Frequently asked questions
How are chemical engineers recruited at RCF?
Management trainees have been recruited through written tests and interviews. Always confirm in the current official notification.
What should I prepare for a RCF chemical engineering interview?
RCF (Rashtriya Chemicals and Fertilizers) works in fertilisers and industrial chemicals: Ammonia, urea, nitric acid and industrial chemicals at Trombay and Thal. Likely focus areas: Fertilisers & gas chemicals, Reactors & catalysts, Utilities, Process safety & plant practice.
Rashtriya Chemicals and Fertilizers: official website
Questions to prepare (170)
- Describe ammonia production from natural gas.
- How is urea made? What is biuret and why is it controlled?
- What is the steam-to-carbon ratio in a reformer and why is it important?
- How is methanol produced?
- How is nitric acid made?
- Why is CO₂ removed before ammonia synthesis, and where does it go?
- What is green hydrogen and why is it discussed in energy interviews?
- What is the difference between prilling and granulation of urea?
- CSTR or PFR — which needs a smaller volume and why?
- What is a catalyst? Does it change equilibrium?
- What is a runaway reaction and how is it prevented?
- Why is ammonia synthesis carried out at high pressure and moderate temperature?
- What are the types of reactors used in industry? Give examples.
- What is conversion, selectivity and yield?
- Why is a purge stream necessary in a recycle loop?
- Why is boiler feed water treated? What is a deaerator?
- How does a DM (demineralisation) plant work?
- Why is instrument air dried? What is its dew point?
- Why do plants use nitrogen? How is it produced?
- What is cooling water treatment and what is cycles of concentration?
- What is an effluent treatment plant in a refinery?
- What is the difference between a fire-tube and a water-tube boiler?
- What is steam quality and why does it matter?
- What are the types of steam in a plant and how is steam generated?
- Why does a steam turbine keep rotating for some time after it is shut down? What is barring/turning gear?
- What is the difference between a back-pressure and a condensing steam turbine?
- Why are compressors provided with intercoolers and knock-out drums?
- How is refinery water reused after treatment, and where does fresh water come from?
- Can water be made from air? How?
- What is boiler blowdown? Why is it needed?
- What are the important boiler mountings and accessories?
- Why does cooling-tower water need make-up and chemical dosing?
- What is a pressure-reducing and desuperheating station (PRDS)?
- What is HAZOP? Explain guide words with an example.
- What is the difference between a safety valve, a relief valve and a rupture disc?
- What is a permit-to-work system? Name the types of permits.
- What is LOTO (lock-out tag-out)?
- What are LEL and UEL? What is flash point and auto-ignition temperature?
- Explain the fire triangle and classes of fire. Which extinguisher for which fire?
- What happened at Bhopal? What lessons did the industry learn?
- Why are vessels purged with nitrogen before start-up and before maintenance?
- What is Management of Change (MOC)?
- What is the hierarchy of controls?
- What do you do if you see a hydrocarbon leak in the plant?
- What is a scrubber and where is it used in a plant?
- What are the types of work permits?
- What PPE is used in a plant? Name types of gloves and their uses.
- How does an incident happen? What is the difference between a near miss, an incident and an accident?
- Can working in a plant affect smell or cause health problems like hair loss? How are workers protected?
- When is a rupture disc used instead of, or together with, a pressure safety valve?
- What is the difference between a gas mask (canister respirator) and an SCBA? When is each used?
- Why are mobile phones not allowed in refinery and plant areas?
- How many people are needed for a maintenance job, and what safety measures apply in different situations?
- What is a gas detector and how are fixed gas detectors used in plants?
- What does hazardous area classification (Zone 0, 1, 2) mean?
- What is the difference between a compressor, a blower and a fan?
- Why is steam used as a heating medium? Why saturated rather than superheated steam?
- What is a steam trap? Name the types.
- Why are evaporators operated as multiple effects?
- Why does an absorber operate at high pressure and low temperature, and a stripper at low pressure and high temperature?
- What is a cooling tower? Explain range and approach.
- How does a membrane separate gases or salts? Give plant uses.
- What is feed-forward and ratio control?
- How do you control the temperature of an exothermic reactor?
- What types of corrosion occur in process plants?
- What is the difference between design pressure, operating pressure and MAWP? What is a hydrotest?
- What are NDT methods used in plants?
- What is creep? Where is it a concern?
- Why is stainless steel used and why can it still crack?
- What is a turnaround (shutdown) and what does a process engineer do in it?
- Tell me about yourself.
- Why do you want to join a PSU (or this company)?
- Explain your final-year project.
- What did you learn during your industrial training or internship?
- What are your strengths and weaknesses?
- Are you willing to work in shifts and remote locations?
- What current developments in the energy sector do you know?
- Why should we hire you?
- A senior asks you to bypass an interlock to restart a unit quickly. What do you do?
- Where do you see yourself in five years?
- How does a Bourdon-tube pressure gauge work?
- What is the difference between a pressure gauge and a pressure transmitter?
- Why is a 4–20 mA signal used and not 0–20 mA?
- What is a DPT (differential pressure transmitter) and where is it used?
- What are the four basic process variables and how is each measured?
- What is a rotameter and why must it be vertical?
- What is a thermowell? Why is it used?
- What is calibration and why is it done regularly?
- How do you know whether a gate valve, a globe valve or a butterfly valve is open or closed?
- What is an NRV (non-return valve)? Where is it fitted on a pump and why?
- Why is the discharge isolation (gate) valve placed after the NRV on a pump?
- What does “crack open” a valve mean?
- What are LO, LC, CSO, CSC (always-open and always-closed) valves?
- What is a pneumatic control valve? What do air-to-open and air-to-close mean?
- What is a solenoid valve and how does it open?
- Name valve types and their uses.
- What is a valve key? Why should cheater bars be avoided?
- What are the detailed types of pumps used in a plant?
- How do you start a centrifugal pump from standby? Give the procedure.
- How do you change over from running pump A to standby pump B?
- How do you safely take a running pump out for maintenance and connect the standby?
- If you are confused whether pump A or pump B is running, how do you find out?
- Why are daily readings of ampere, pressure and temperature taken for pumps and motors?
- What is multistage in a pump or compressor? Why is it used?
- What is the head of a pump? Why is it expressed in metres and not bar?
- How is a line identified on a P&ID? Explain the line number.
- What do the different line types mean on a P&ID?
- What are pipe colour codes used in plants?
- What is MOC (material of construction) and how is it chosen for a line?
- What are a ferrule, a nut-and-bolt (stud bolt) and a gasket used for in piping?
- Why are Teflon tape and copper tape used?
- Why are lines and equipment insulated? What are glass wool, rock wool and calcium silicate used for?
- What is a strainer? Why is it placed before pumps?
- Why are platforms and walkways made of gratings and not concrete?
- What is erosion in pipes and how is it different from corrosion? How are both controlled?
- What is draft in a furnace? Why is negative pressure maintained?
- What are the types of furnaces and heaters in a refinery?
- What are refractory bricks and castables? Why are they used in furnaces?
- What are the types of heaters and coils used in process plants?
- What is shift duty in a plant? Explain handover and takeover.
- What does a shift-in-charge do?
- Why are daily samples collected and tested in plants? What does the lab do?
- Why are trends used in DCS? What can a trend tell you?
- What is the difference between DCS, SCADA and PLC? Where is each used in a refinery or pipeline?
- Why doesn’t a refinery shut down when one relay, SSR or MCB trips?
- What is an electrical substation in a plant?
- What are walkie-talkies used for, and why must they be intrinsically safe?
- What are daily rounds and log sheets in a plant?
- How does the purchase process work in a PSU plant? Explain indent, quotation and purchase order.
- What is delegation of financial powers? Why can an officer approve only up to a limit (e.g. ₹50 000 a month)?
- How is a departmental budget prepared and controlled?
- How should an engineer write an official email to a vendor or another department?
- What allowances and benefits do PSU engineers get? What is PRP (bonus)?
- What is the future of the oil and gas industry?
- What are the types of compressors and where is each used?
- How is a reciprocating compressor started?
- What are dry gas seals in centrifugal compressors?
- What is the difference between a steam turbine and a gas turbine?
- In which order are hot and cold fluids introduced when starting a heat exchanger?
- How do you detect a tube leak in a heat exchanger?
- How are heat exchangers cleaned?
- What is a gauge glass and how is it used safely?
- What is the difference between an alarm, an interlock and a trip?
- What is an orifice flow meter and why is it the most common in plants?
- What is preventive, predictive and breakdown maintenance?
- What is the difference between pressure, gauge pressure and absolute pressure? What is vacuum?
- What is the difference between temperature, heat and heat flow? Why do we measure temperature at many points?
- What is hydrotesting of a line before commissioning, and what is pneumatic testing?
- Why are expansion loops and bellows provided in pipelines?
- What is the purpose of a spectacle blind and a spade?
- What is pre-commissioning and commissioning of a unit?
- What is GeM and what are the types of tenders?
- What is L1 and how are bids compared?
- What is the difference between a purchase order and a work order (service contract)?
- What do you know about the organisation you are applying to?
- How would you handle a disagreement with a senior operator who has more experience than you?
- What is a bypass line around a control valve and why is it provided?
- What is a balance line in a pump?
- What is the minimum flow (minimum continuous flow) of a centrifugal pump and how is it protected?
- What is a pressure control valve (PCV) and how is it different from a PSV?
- How is gas flow measured? What is a gas meter?
- How are electrical cables laid and connected in a refinery?
- Why does a control room have a raised (hollow) floor and false ceiling?
- Why is the temperature kept very low in a control room or rack room?
- How do you keep a healthy body and mind while working rotating shifts?
- Why don’t well-maintained compressors and multistage pumps make as much noise as you might expect? How is plant noise controlled?
- Which pump would you choose for which service? Give a quick guide.
- What are the components of a PSU engineer’s salary along with basic pay?
- What are vents and drains on lines and equipment for?
- Why is there liquid (glycerine) inside some pressure gauges?
Organisation names show where a topic is a likely focus because of what the organisation does; they are not claims that a particular question was asked. Recruitment routes change each year, so confirm in the official notification.