CSTR or PFR — which needs a smaller volume and why?
Answer. For positive-order reactions a PFR needs less volume for the same conversion, because it operates at the high inlet concentration and only gradually reaches the low outlet concentration.
Why. A CSTR is perfectly mixed, so the whole volume reacts at the low outlet concentration (lowest rate). On a Levenspiel plot (F_A0/−r_A vs X) the CSTR volume is the rectangle, the PFR the area under the curve.
How.
- CSTR: V = F_A0X/(−r_A)_exit.
- PFR: V = F_A0∫dX/(−r_A).
- CSTRs in series approach PFR behaviour.
- CSTRs win for autocatalytic reactions at low conversion, strong temperature control and liquid-phase reactions needing mixing.
What is a catalyst? Does it change equilibrium?
Answer. A substance that speeds up a reaction by providing a path with lower activation energy, without being consumed. It does not change equilibrium conversion — it only helps reach it faster.
Why. It lowers the activation energy of forward and reverse reactions equally, so K = k_f/k_r is unchanged.
How.
- Selectivity: a good catalyst favours the desired path (e.g. silver for ethylene oxide).
- Deactivation by coking, sintering, poisoning (S, metals, chlorides) and attrition.
- Regeneration: burn coke (FCC), reduce, or replace.
Only in industry. Catalyst life decides turnaround intervals; plants track reactor ΔT, ΔP and product quality to decide when to raise temperature (end-of-run) or change catalyst.
What is a runaway reaction and how is it prevented?
Answer. A loss of temperature control where heat generation (exponential in T) outruns heat removal (linear in T), so temperature and rate accelerate.
Why. Arrhenius: rate doubles every ~10 °C; cooling grows only with ΔT. Beyond a critical point (Semenov) there is no stable balance.
How.
- Design: adequate cooling, small batch inventory, semi-batch addition of reagent.
- Controls: high-temperature interlocks to stop feed, emergency cooling, quench or kill agents.
- Relief: rupture discs and vent sizing for two-phase flow (DIERS).
- Know the onset temperature from calorimetry (DSC, ARC).
Only in industry. Bhopal (MIC), Seveso and many fine-chemical accidents were runaways. HAZOP always asks: what if cooling fails or reagent is added too fast?
What is residence time distribution and why is it measured?
Answer. The distribution of times that fluid elements spend in a vessel, measured by injecting a tracer and recording the outlet concentration.
Why. Real reactors are neither ideal PFR nor CSTR; dead zones, channelling and bypassing reduce conversion. RTD diagnoses these flaws.
How.
- Pulse or step tracer; E(t) curve; mean time t_m = ∫tE dt.
- Compare t_m with V/Q: smaller suggests dead volume, early peak suggests bypass.
- Models: tanks-in-series, axial dispersion.
Only in industry. Radioactive tracer studies (BARC isotope services) diagnose refinery columns and reactors without shutdown.
Why is ammonia synthesis carried out at high pressure and moderate temperature?
Answer. N₂ + 3H₂ ⇌ 2NH₃ is exothermic with a decrease in moles: high pressure (150–250 bar) favours equilibrium; temperature (~400–500 °C) is a compromise between rate and equilibrium.
Why. Le Chatelier: fewer moles on the product side favours high P; exothermic reaction favours low T, but the iron catalyst is too slow at low T.
How.
- Iron catalyst promoted with K₂O and Al₂O₃.
- Conversion per pass ~15–25 %; ammonia condensed and unreacted gas recycled; purge removes inerts (Ar, CH₄).
- Interbed cooling keeps the reaction on track.
What is the Thiele modulus and effectiveness factor?
Answer. φ compares reaction rate with pore-diffusion rate in a catalyst pellet; η = actual rate / rate if the whole pellet saw surface concentration.
Why. Fast reactions consume reactant before it penetrates the pores; the inside of the pellet is wasted (η ≈ 1/φ at large φ).
How.
- φ = L√(k/D_e).
- Small φ (< 0.4): η ≈ 1. Large φ: η ≈ 1/φ.
- Use smaller pellets, egg-shell catalysts or larger pores to raise η.
Batch or continuous process — how do you decide?
Answer. Continuous for large, steady production of one product; batch for small volumes, many products, long reactions or strict traceability (pharma, speciality chemicals).
Why. Continuous plants have lower cost per tonne and steady quality but are inflexible; batch plants are flexible but have downtime and labour per batch.
How.
- Rule of thumb: above ~5000 t/y of one product, continuous is usually cheaper.
- Semi-batch to control exotherms.
- Hybrid trains (batch reaction, continuous separation) are common.
What are the types of reactors used in industry? Give examples.
Answer. Stirred tanks, tubular, fixed bed, fluidised bed, moving bed, slurry, trickle bed and bubble columns.
Why. Choice depends on phases, heat of reaction, catalyst life and scale.
How.
- Fixed bed: hydrotreating, ammonia, methanol, reforming.
- Fluidised: FCC, acrylonitrile, PE (UNIPOL).
- Moving bed: CCR reformer.
- Tubular: steam cracking furnace, reformer tubes.
- Slurry: HDPE, Fischer–Tropsch.
What is conversion, selectivity and yield?
Answer. Conversion: fraction of reactant consumed. Selectivity: desired product formed per unwanted product (or per reactant consumed). Yield: desired product per reactant fed.
Why. High conversion with poor selectivity wastes feed; plants often run at modest conversion with recycle to keep selectivity high.
How.
- Yield = conversion × selectivity (fractional definition).
- Example: ethylene oxide plants run ~10 % per-pass conversion to keep selectivity ~85–90 %.
Why is a purge stream necessary in a recycle loop?
Answer. To remove inerts or by-products that enter with the feed and would otherwise accumulate without limit in the loop.
Why. Steady state requires every species entering to leave; inerts have no other exit.
How.
- Purge fraction set by balance: inert in feed = inert out with purge.
- Ammonia loop purges argon and methane; hydrogen is recovered from the purge by PSA or membranes.
Organisation names show where a topic is a likely focus because of what the organisation does; they are not claims that a particular question was asked. Recruitment routes change each year, so confirm in the official notification.