IITIAN1997 STUDIO

Nuclear & heavy water: interview questions

12 questions · PHWR, heavy-water production, three stages, PUREX, ALARA

Practise with animations →

Why does India’s PHWR use heavy water? Why can it use natural uranium?

Answer. Heavy water is an excellent moderator with very low neutron absorption, so enough neutrons survive to sustain fission in natural uranium (0.7 % U-235) without enrichment.

Why. Deuterium absorbs far fewer neutrons than ordinary hydrogen; light-water reactors lose too many neutrons and need enriched fuel.

How.

  1. Pressurised heavy water reactors: fuel bundles in horizontal pressure tubes, heavy-water coolant and a separate low-temperature moderator in the calandria.
  2. On-power refuelling keeps reactivity steady.
  3. Indian PHWRs: 220 MWe and 700 MWe designs operated by NPCIL.

Open this question

How is heavy water produced? Explain the bithermal exchange principle.

Answer. By chemical exchange of deuterium between two compounds in cold and hot towers — e.g. hydrogen sulphide–water (Girdler sulphide) or ammonia–hydrogen — followed by vacuum distillation to final purity.

Why. The equilibrium distribution of deuterium between the compounds depends on temperature: in H₂S–water, deuterium prefers water in the cold tower and moves back to H₂S in the hot tower, so cycling between them enriches one stream.

How.

  1. Natural water has ~150 ppm D; many stages of enrichment reach ~15–30 %.
  2. Final enrichment by vacuum distillation of water to 99.8 % D₂O (reactor grade).
  3. India has operated plants using both H₂S–water and ammonia-based processes; the Heavy Water Board runs them.

Only in industry. H₂S–water plants handle large inventories of toxic H₂S — safety systems dominate their design.

Open this question

Describe India’s three-stage nuclear power programme.

Answer. Stage 1: PHWRs on natural uranium produce power and plutonium. Stage 2: fast breeder reactors use plutonium and breed more fissile material (and U-233 from thorium blankets). Stage 3: thorium-based reactors use U-233.

Why. India has limited uranium but large thorium reserves; breeding makes thorium usable in the long run.

How.

  1. PFBR (500 MWe, Kalpakkam) is sodium-cooled.
  2. Reprocessing (PUREX) links the stages.
  3. AHWR design aims at thorium utilisation.

Open this question

What is the PUREX process?

Answer. Plutonium Uranium Reduction EXtraction: spent fuel is dissolved in nitric acid; uranium and plutonium are extracted into tri-butyl phosphate (≈30 % in dodecane), leaving fission products in the aqueous raffinate; plutonium is then reduced to Pu(III) to partition it from uranium.

Why. TBP forms complexes with U(VI) and Pu(IV) nitrates but not with most fission products; Pu(III) is not extractable, enabling separation.

How.

  1. Head end: chopping, dissolution, clarification.
  2. Co-decontamination cycle, partitioning cycle, purification cycles.
  3. Equipment: mixer–settlers, pulsed columns, centrifugal contactors; all remote and shielded.
  4. High-level waste is vitrified.

Open this question

Why must a reactor be cooled even after shutdown?

Answer. Fission products keep releasing decay heat — about 6–7 % of full power just after shutdown, falling to ~1 % in hours — enough to melt fuel without cooling.

Why. Radioactive decay continues regardless of the chain reaction stopping.

How.

  1. Shutdown cooling systems, emergency core cooling, passive systems (natural circulation, gravity tanks).
  2. Fukushima (2011) lost power for cooling after the tsunami, leading to core damage.

Open this question

What are the units of radiation dose? What is ALARA?

Answer. Becquerel: activity (decays per second). Gray: absorbed energy (J/kg). Sievert: dose equivalent weighted for radiation type and tissue. ALARA: keep exposure As Low As Reasonably Achievable.

Why. Different radiations harm tissue differently (alpha far more per gray inside the body).

How.

  1. Protection by time, distance (inverse square) and shielding (lead for gamma, concrete, water; hydrogen-rich materials for neutrons).
  2. Occupational limit (ICRP/AERB): 20 mSv/y averaged over 5 years.
  3. Dosimeters (TLD) for workers.

Open this question

What is the role of moderator, coolant and control rods in a reactor?

Answer. Moderator slows fast neutrons to thermal energy where fission of U-235 is likely; coolant removes heat; control rods absorb neutrons to control or stop the chain reaction.

Why. Thermal neutrons have a much higher fission cross-section in U-235; absorbers (boron, cadmium) make k_eff below 1.

How.

  1. Moderators: light water, heavy water, graphite.
  2. Coolants: water, heavy water, CO₂, liquid sodium (fast reactors).
  3. Shutdown systems: rods and liquid poison injection (gadolinium nitrate in PHWR).

Open this question

Why is zirconium alloy used for fuel cladding and pressure tubes?

Answer. Zirconium has very low neutron absorption, good corrosion resistance in hot water and adequate strength.

Why. Structural materials in the core must not waste neutrons; zirconium absorbs far fewer than steel.

How.

  1. Zircaloy-2/4 for cladding; Zr-2.5Nb for PHWR pressure tubes.
  2. Concerns: hydrogen pick-up and hydride embrittlement, Zr–steam reaction at high temperature in accidents.
  3. India’s Nuclear Fuel Complex, Hyderabad, makes fuel and zirconium components.

Open this question

How is high-level radioactive waste managed?

Answer. High-level liquid waste from reprocessing is concentrated, vitrified in borosilicate glass, filled into stainless canisters and stored with cooling, pending deep geological disposal.

Why. Glass locks the fission products into a durable, leach-resistant solid.

How.

  1. Low and intermediate waste: treatment (ion exchange, evaporation), cementation, near-surface disposal.
  2. India operates waste immobilisation plants (e.g. at Trombay, Tarapur, Kalpakkam).

Open this question

What are radioisotope applications in industry?

Answer. Radiotracers to measure flows, RTD and leaks; gamma scanning of columns; radiography of welds; nucleonic level and density gauges; sterilisation and food irradiation.

Why. Gamma rays penetrate steel, so the inside of operating equipment can be studied without shutdown.

How.

  1. Gamma scan of a distillation column shows tray damage, flooding or missing packing.
  2. Tracer injection gives RTD of reactors and flow rates in pipelines.
  3. BARC/BRIT provide isotopes and services.

Open this question

What is uranium enrichment? Why does a PHWR not need it?

Answer. Raising the U-235 fraction above natural 0.7 % (to ~3–5 % for LWRs) by gas centrifuges using UF₆; PHWRs use heavy water’s neutron economy to run on natural uranium.

Why. The 1 % mass difference between U-235 and U-238 hexafluorides is separated in many centrifuge stages (cascades).

How.

  1. Separative work units (SWU) measure effort.
  2. Light-water reactors (e.g. Kudankulam VVER) use enriched fuel.

Open this question

Why is a BARC interview considered fundamentals-heavy, and how should you prepare?

Answer. BARC panels probe a few subjects you choose in depth, asking why behind every formula, derivations from first principles and applications to nuclear plants.

Why. Research and plant work need engineers who understand fundamentals rather than memorised results.

How.

  1. Pick 2–3 core subjects (e.g. mass transfer, heat transfer, thermodynamics) and master derivations and physical meaning.
  2. Expect follow-ups: “Why log mean?”, “Derive the Fenske equation”, “What if the assumption fails?”.
  3. Revise your project thoroughly; be honest when you do not know.
  4. Read basics of the nuclear fuel cycle and heavy-water production.

Open this question

Organisation names show where a topic is a likely focus because of what the organisation does; they are not claims that a particular question was asked. Recruitment routes change each year, so confirm in the official notification.

Practise with animations →