IITIAN1997 STUDIO

Gauges, transmitters & meters: interview questions

13 questions · Bourdon gauges, PT vs gauge, 4–20 mA, DPT, rotameters, calibration, alarms vs trips

Practise with animations →

How does a Bourdon-tube pressure gauge work?

Answer. A curved, flattened metal tube tends to straighten when pressure acts inside it; the tip movement is magnified by a linkage and gear to move the pointer.

Why. Pressure acts on a larger area on the outer side of the curved tube than on the inner side, creating a net force that opens the curve in proportion to pressure.

How.

  1. Select a range so normal pressure is in the middle third of the dial (the gauge reads 1.5–2 × operating pressure at full scale).
  2. Use a siphon (pigtail) on steam lines so hot steam does not reach the tube.
  3. Use a snubber or glycerine-filled gauge where pressure pulsates (pump discharge).
  4. Use a diaphragm seal for corrosive, viscous or slurry fluids.
  5. Gauges have an isolation valve and are calibrated periodically against a dead-weight tester.

Only in industry. A gauge that reads zero is not proof that a line is depressurised — the gauge may be choked or its valve closed. Always bleed and check before opening.

Open this question

What is the difference between a pressure gauge and a pressure transmitter?

Answer. A gauge only shows pressure locally; a transmitter converts pressure into a 4–20 mA (or digital) signal sent to the DCS for display, alarm, control and trip.

Why. The control room needs live values for control loops and interlocks; a field gauge needs a person to read it.

How.

  1. Transmitters use strain-gauge, capacitive or piezo-resistive sensors.
  2. 4 mA = zero of range (live zero), 20 mA = full scale; below ~3.8 mA indicates a broken wire or fault.
  3. HART protocol rides on the 4–20 mA for diagnostics.
  4. Plants keep a local gauge near important transmitters so the operator can cross-check.

Only in industry. When the DCS reading looks odd, the field operator is asked to “check the local gauge” — mismatch usually means a choked impulse line or a transmitter needing calibration.

Open this question

Why is a 4–20 mA signal used and not 0–20 mA?

Answer. Because 4 mA is a “live zero”: a broken wire gives 0 mA, which the system recognises as a fault instead of a genuine zero reading.

Why. With 0–20 mA, a cut cable would look like “zero pressure” and could cause a wrong action. The 4 mA also powers two-wire transmitters.

How.

  1. Value = LRV + (I − 4)/16 × span.
  2. Example: 0–10 bar transmitter showing 12 mA reads 5 bar.
  3. Current signals are not affected by cable resistance over long distances, unlike voltage.

Open this question

What is a DPT (differential pressure transmitter) and where is it used?

Answer. A transmitter that measures the difference between two pressures (high side and low side); used for flow across an orifice, level in vessels, filter and strainer ΔP and column ΔP.

Why. Many process variables show up as a pressure difference: flow (ΔP ∝ Q²), liquid level (ΔP = ρgh), and fouling or blockage.

How.

  1. Flow: DPT across orifice, square-root extraction in the transmitter or DCS.
  2. Level: high side at bottom, low side at top (dry leg) or with a filled reference leg (wet leg).
  3. Three-valve or five-valve manifold: open equalising valve first, then isolate, to avoid over-ranging one side.
  4. Zero check: equalise both sides and confirm 4 mA.

Only in industry. Commissioning a DPT in the wrong sequence (opening one side with the equaliser closed) can damage the cell — the manifold sequence is a classic field question.

Open this question

What are the four basic process variables and how is each measured?

Answer. Pressure (gauges, transmitters), temperature (thermocouples, RTDs, thermometers), flow (orifice, magnetic, Coriolis, vortex, rotameter) and level (gauge glass, DPT, radar, displacer).

Why. Nearly every control loop and safety trip uses one of these four.

How.

  1. P: Bourdon gauge locally, transmitter to DCS.
  2. T: thermocouple in a thermowell; RTD for accuracy.
  3. F: orifice + DPT most common; Coriolis for mass flow.
  4. L: gauge glass locally, DPT or radar remotely.

Open this question

What is a rotameter and why must it be vertical?

Answer. A variable-area flow meter: a float rises in a tapered tube until the drag force of the flow balances its weight; float height gives flow.

Why. The balance between gravity on the float and fluid drag only works when the tube is vertical with flow upward.

How.

  1. Read at the float’s reading edge (usually the widest part).
  2. Calibrated for a specific fluid density; correct for other fluids.
  3. Used for purge flows, sample lines, small chemical dosing.

Open this question

What is a thermowell? Why is it used?

Answer. A closed metal tube inserted into the process into which the temperature sensor is placed.

Why. It protects the sensor from pressure, corrosion and flow and lets the sensor be removed without stopping the process.

How.

  1. Check wake frequency (vibration) at high velocities.
  2. It adds a small time lag to the measurement.
  3. Spare thermowells allow a test thermometer to be inserted for cross-checking.

Open this question

What is calibration and why is it done regularly?

Answer. Comparing an instrument against a known standard and adjusting its zero and span so it reads correctly.

Why. Sensors drift with time, temperature, vibration and fouling; wrong readings lead to off-spec product or missed trips.

How.

  1. Five-point check (0, 25, 50, 75, 100 %) rising and falling.
  2. Pressure: dead-weight tester or calibrator; temperature: dry-block calibrator.
  3. Record as-found and as-left values; tag with calibration date.
  4. Safety instruments follow stricter proof-test intervals.

Open this question

What is a gauge glass and how is it used safely?

Answer. A transparent column connected to a vessel through top and bottom isolation valves showing liquid level directly; magnetic and reflex types are used for higher pressures and hazardous fluids.

Why. It gives a direct local level reading to cross-check transmitters.

How.

  1. Blow down the glass to clean it: close top valve, open drain, then reverse to flush both connections.
  2. Ball-check valves in gauge cocks stop flow if the glass breaks.
  3. Avoid ordinary glass in toxic or high-pressure service.

Open this question

What is the difference between an alarm, an interlock and a trip?

Answer. An alarm warns the operator to act; an interlock prevents an unsafe action or sequence (e.g. pump cannot start with suction valve closed); a trip automatically shuts equipment or a unit down when a limit is crossed.

Why. Layers of protection: operator response first, automatic action when it is too late for people.

How.

  1. Typical set points: high alarm (H), high-high trip (HH).
  2. Permissives allow start only when conditions are healthy.
  3. Trips are tested periodically; bypasses need authorisation.

Open this question

What is an orifice flow meter and why is it the most common in plants?

Answer. A thin plate with a hole in the line creates a pressure drop proportional to the square of flow; a DPT measures it and the flow is computed (Q ∝ √ΔP).

Why. It is cheap, simple, standardised (ISO 5167), has no moving parts and can be changed easily for a new range.

How.

  1. Needs straight pipe upstream and downstream.
  2. Permanent pressure loss is high (40–90 % of ΔP).
  3. Range ~3–4:1; for wide ranges use other meters.
  4. Bore wear or fouling causes error — inspect during shutdowns.

Open this question

How is gas flow measured? What is a gas meter?

Answer. By diaphragm meters (domestic PNG), rotary/turbine meters (commercial and industrial), ultrasonic meters (large pipelines and custody transfer), orifice meters with flow computers, and Coriolis or thermal mass meters for process gas.

Why. Gas volume changes with pressure and temperature, so volumetric readings must be corrected to standard conditions for billing (SCM).

How.

  1. Electronic volume correctors use measured P and T (and gas composition).
  2. Custody-transfer stations have metering runs, filters and prover checks.
  3. Units: standard cubic metres (SCM), MMSCMD for pipelines.

Open this question

Why is there liquid (glycerine) inside some pressure gauges?

Answer. The case is filled with glycerine (or silicone oil) to damp the pointer: it stops needle flutter from vibration and pressure pulsation, protects the movement from wear and corrosion, and keeps moisture out so the dial does not fog.

Why. Near pumps and compressors the pressure pulses many times a second; in a dry gauge the pointer shakes, becomes unreadable, and the gears and linkage wear out quickly. The viscous liquid slows the pointer’s movement without changing the reading.

How.

  1. Used on pump and compressor discharges, hydraulic systems and vibrating skids.
  2. Glycerine for normal temperatures; silicone oil for very cold or hot locations (glycerine thickens in cold).
  3. Not for oxygen or strong oxidiser service — use dry or special-fluid gauges there.
  4. A gauge with low liquid level or a cloudy fill should be replaced; a small vent plug relieves case pressure from temperature changes.
  5. For severe pulsation, add a snubber in the gauge line as well.

Only in industry. If a liquid-filled gauge’s pointer still shakes, the pulsation is severe — fit a snubber or check the pump for cavitation or a faulty valve.

Open this question

Organisation names show where a topic is a likely focus because of what the organisation does; they are not claims that a particular question was asked. Recruitment routes change each year, so confirm in the official notification.

Practise with animations →