IITIAN1997 STUDIO

Fertilisers & gas chemicals: interview questions

8 questions · Ammonia, urea, methanol, nitric acid, green hydrogen

Practise with animations →

Describe ammonia production from natural gas.

Answer. Desulphurised natural gas is steam-reformed to syngas, air is added in a secondary reformer to supply nitrogen, CO is shifted to CO₂ and H₂, CO₂ is removed, traces of CO/CO₂ are methanated, and the 3:1 H₂/N₂ gas is compressed and converted over iron catalyst.

Why. Each step prepares a clean hydrogen–nitrogen mixture; oxygen compounds poison the ammonia catalyst.

How.

  1. Primary reformer: Ni catalyst in tubes ~800 °C, steam/carbon ratio ~3.
  2. Secondary reformer: air burns some H₂, raising temperature; adds N₂.
  3. HT shift (Fe–Cr ~350–400 °C), LT shift (Cu–Zn ~200 °C).
  4. CO₂ removal (Benfield, aMDEA) — CO₂ goes to urea.
  5. Synthesis loop 150–200 bar, refrigeration to condense NH₃.

Open this question

How is urea made? What is biuret and why is it controlled?

Answer. NH₃ and CO₂ react at ~140–160 bar to ammonium carbamate, which dehydrates to urea and water; unconverted carbamate is decomposed and recycled; the solution is concentrated and prilled or granulated. Biuret forms when urea is heated too long and is harmful to some crops.

Why. Carbamate formation is fast and exothermic; dehydration to urea is slow and equilibrium-limited, so recycle is essential.

How.

  1. Stripping processes (CO₂ or NH₃ stripping) recover carbamate efficiently.
  2. Keep biuret low (Indian FCO limit 1.5 % for fertiliser urea) by short residence time at high temperature.
  3. India mandates neem-coated urea (since 2015) to reduce diversion and slow nitrogen release.

Open this question

What is the steam-to-carbon ratio in a reformer and why is it important?

Answer. Moles of steam per mole of carbon in the hydrocarbon feed (typically ~2.5–3.5); too low a ratio causes carbon deposition on the nickel catalyst.

Why. Reactions like CH₄ → C + 2H₂ and 2CO → C + CO₂ form coke when steam is short; excess steam shifts equilibrium away from carbon.

How.

  1. Interlocks trip feed on low steam flow.
  2. Higher S/C costs energy (more steam), so plants optimise it.
  3. Tube-skin temperatures and pressure drop show coking.

Open this question

How is methanol produced?

Answer. From syngas (CO, CO₂, H₂) over Cu/ZnO/Al₂O₃ catalyst at ~50–100 bar and 220–280 °C, followed by distillation.

Why. Exothermic, equilibrium-limited reaction: low temperature favours conversion but the catalyst needs ~250 °C for rate; per-pass conversion is modest, so the gas is recycled.

How.

  1. CO + 2H₂ ⇌ CH₃OH; CO₂ + 3H₂ ⇌ CH₃OH + H₂O.
  2. Isothermal (steam-raising) reactors remove heat.
  3. Purge keeps inerts low.

Open this question

How is nitric acid made?

Answer. Ostwald process: ammonia is oxidised with air over platinum–rhodium gauze at ~850–900 °C to NO, which is oxidised to NO₂ and absorbed in water to give nitric acid.

Why. Very short contact on Pt–Rh favours NO over N₂; NO₂ absorption needs cooling and pressure.

How.

  1. 4NH₃ + 5O₂ → 4NO + 6H₂O.
  2. 2NO + O₂ → 2NO₂; 3NO₂ + H₂O → 2HNO₃ + NO.
  3. Tail-gas treatment for NOx and N₂O.

Open this question

Why is CO₂ removed before ammonia synthesis, and where does it go?

Answer. CO₂ (and CO) are oxygen compounds that poison the iron synthesis catalyst and would form ammonium carbamate in the loop; the recovered CO₂ is the raw material for urea.

Why. Oxygen compounds oxidise the active iron surface.

How.

  1. Hot potassium carbonate (Benfield) or activated MDEA absorption.
  2. Methanation converts traces to methane (inert, purged).

Open this question

What is green hydrogen and why is it discussed in energy interviews?

Answer. Hydrogen made by water electrolysis using renewable electricity, with near-zero CO₂ emissions. India’s National Green Hydrogen Mission (2023) targets about 5 million tonnes a year by 2030.

Why. Refineries and fertiliser plants are the largest hydrogen users; today’s grey hydrogen from steam reforming emits ~9–10 kg CO₂ per kg H₂.

How.

  1. Electrolysers: alkaline, PEM, solid oxide (~50–55 kWh/kg H₂).
  2. Uses: refinery hydrotreating, green ammonia, methanol, steel.
  3. Challenges: cost of electricity, storage and transport.

Open this question

What is the difference between prilling and granulation of urea?

Answer. Prilling sprays molten urea from the top of a tall tower; droplets solidify as they fall into small prills (~1–2 mm). Granulation grows larger, harder granules (2–4 mm) by spraying urea onto recycled seed particles in a fluid bed.

Why. Granules are stronger, less dusty and better for bulk handling and blending; prilling is cheaper but emits dust.

How.

  1. Prill towers need large air flows and dust scrubbers.
  2. Granulators use fluidised beds with formaldehyde additive for hardness.

Open this question

Organisation names show where a topic is a likely focus because of what the organisation does; they are not claims that a particular question was asked. Recruitment routes change each year, so confirm in the official notification.

Practise with animations →