IITIAN1997 STUDIO

Process Equipment Design-I (2018)

Exchangers, thick shells and tanks, drawn to code.

Open the interactive studio →

Shell-and-tube, double-pipe and condenser design by Kern, thick-walled high-pressure vessels (Lamé), API 650 storage-tank courses, heads and opening compensation, separation-equipment drawings and jacketed reactors from the ASTU CHE181701 syllabus (2018-19 scheme).

What is inside

  • Kern design of exchangers, condensers and evaporators
  • Thick cylinders and high-pressure vessels
  • Tank shells, heads and nozzle reinforcement
  • Jacketed reactor vessels

Syllabus: ASTU CHE181701 Process Equipment Design-I (2018 scheme), semester 7, 2018-19 scheme. Official syllabus PDF.

Design of heat-transfer equipment

Topics: Design and drawing of heat exchangers with and without phase change, evaporators and condensers.

Kern’s method for shell-and-tube exchangers

Process design starts from the heat balance Q = m_hc_h(T₁ − T₂) = m_cc_c(t₂ − t₁), then the LMTD with the correction factor for the pass arrangement (F_T ≥ 0.75, otherwise add shells), an assumed overall coefficient U, and a trial area A = Q/(UF_TΔT_lm). Fluid allocation: corrosive, fouling, high-pressure or cooling water go on the tube side (easier to clean, cheaper alloy); viscous or condensing fluids usually on the shell side.

From the trial area choose tube size (19.05 mm or 25.4 mm OD, BWG 14–16), length (2.44, 3.66, 4.88, 6.1 m), pitch (1.25 d_o triangular or square for cleaning) and passes; count tubes and find the shell diameter from tube-count tables. Tube-side h_i: Sieder–Tate/Dittus–Boelter (Nu = 0.023Re^0.8Pr^⅓(μ/μ_w)^0.14) with velocity 1–2.5 m/s for liquids. Shell-side h_o by Kern: equivalent diameter, cross-flow area a_s = D_sCB/P_T, j_H chart. Clean and dirt coefficients: 1/U_d = 1/h_o + R_do + (d_o ln(d_o/d_i))/(2k_w) + (d_o/d_i)(R_di + 1/h_i). Check U_calc ≥ U_assumed and pressure drops (tube ≤ 70 kPa, shell ≤ 35–70 kPa for liquids).

With phase change: a condenser uses Nusselt’s film theory (horizontal tubes h = 0.725[k³ρ²gλ/(μd_oΔT N^(1/6)... )]^¼, or the Kern loading form), with the condensing coefficient large and often the water side controlling; vent non-condensables; for sub-cooling or desuperheating split the duty into zones. Reboilers and evaporators use nucleate-boiling correlations (Mostinski) with a maximum flux check. Drawings: TEMA designation (e.g. AES, BEM), tube sheet layout, baffles (25 % cut, spacing 0.2–1 D_s), tie rods, nozzles, saddles.

  • Q from heat balance; LMTD × F_T.
  • Assume U, find area, choose tubes and shell.
  • h_i (Sieder–Tate), h_o (Kern), fouling.
  • Check U and pressure drops.

Example: A kerosene cooler: duty 600 kW, LMTD 45 K, F_T = 0.9, assumed U = 350 W/m²K. Tubes 19.05 mm OD × 4.88 m. How many tubes?

  1. A = Q/(UF_TΔT) = 600 000/(350 × 0.9 × 45) = 42.3 m².
  2. Area per tube = π × 0.01905 × 4.88 = 0.292 m².
  3. Tubes = 42.3/0.292 = 145 → choose 148 from the tube-count table.

Answer: About 148 tubes, then check h_i, h_o and U.

Shell-and-tube design (Kern): heat balance, LMTD with F_T, assumed U, trial area, tube size/length/pitch/passes, tube count and shell diameter, h_i by Sieder–Tate, h_o by Kern’s j_H method, fouling resistances, U_d and pressure-drop checks; TEMA types. Double-pipe exchangers for small duties (hairpins). Condensers: Nusselt film coefficients, vertical vs horizontal tubes, non-condensables. Evaporators: boiling coefficients, BPR, single and multiple effects.

  • F_T < 0.75: add another shell.
  • Fouling fluid on the tube side.
  • Triangular pitch packs more tubes; square pitch for cleaning.
  • Baffle cut 25 %, spacing 0.2–1 D_s.
  • Condensers: horizontal tubes usually better.

Key formulas

  • Q = UAF_TΔT_lm
  • Nu = 0.027Re^0.8Pr^⅓(μ/μ_w)^0.14
  • 1/U_o = 1/h_o + R_o + d_o ln(d_o/d_i)/2k + (d_o/d_i)(R_i + 1/h_i)
  • a_s = D_sCB/P_T

Practice questions

Which fluid is normally placed in the tubes?

  1. the less fouling one
  2. cooling water or corrosive fluid
  3. the condensing vapour
  4. the viscous oil
Show the answer

Answer: B. cooling water or corrosive fluid Cleaning and alloy cost.

If F_T is below 0.75 one should

  1. accept it
  2. use more shell passes
  3. reduce U
  4. increase fouling
Show the answer

Answer: B. use more shell passes Avoid temperature cross.

Kern’s method is used to calculate

  1. tube-side h only
  2. shell-side h and pressure drop
  3. tank thickness
  4. column height
Show the answer

Answer: B. shell-side h and pressure drop Equivalent diameter and j_H.

Square pitch is chosen when

  1. maximum tubes are needed
  2. the shell side must be cleaned mechanically
  3. the fluid is clean
  4. the shell is small
Show the answer

Answer: B. the shell side must be cleaned mechanically Cleaning lanes.

TEMA type AES has

  1. fixed tube sheets
  2. a floating head
  3. U-tubes
  4. no baffles
Show the answer

Answer: B. a floating head S = floating head with backing device.

Theory questions

Explain the design of a horizontal shell-and-tube condenser. (5 marks)

Show the model answer

Heat balance gives the condensing duty (plus desuperheating and sub-cooling zones if present). Choose cooling water in the tubes (fouling, cleaning) and vapour on the shell side. Assume U (e.g. 700–1000 W/m²K for steam/organics), find LMTD and area. Condensing coefficient by Nusselt for horizontal tubes, h = 0.725[k³ρ(ρ − ρ_v)gλ/(μd_oΔT N_r)]^¼ or Kern’s loading form; tube-side h from Sieder–Tate at 1.5–2 m/s. Include fouling, check U and pressure drop. Provide a vent for non-condensables, baffles with vertical cut, an impingement plate at the vapour inlet, and a large condensate outlet. TEMA type often AEL or BEM.

Describe the step-by-step design of a shell-and-tube heat exchanger by Kern’s method. (10 marks)

Show the model answer

1. Specification: flows, temperatures, properties, allowable pressure drops, fouling factors. 2. Heat balance; unknown outlet temperature. 3. Fluid allocation. 4. LMTD, R and S, F_T for 1-2 passes (≥ 0.75). 5. Assume U (tables), A = Q/(UF_TΔT_lm). 6. Choose tube OD, BWG, length, pitch, layout; number of tubes; passes for tube velocity 1–2 m/s; shell diameter from tube-count table. 7. Tube side: Re, Pr, h_i (Sieder–Tate), refer to OD. 8. Shell side: baffle spacing, a_s = D_sCB/P_T, G_s, D_e, Re_s, j_H, h_o. 9. Clean U_c and design U_d with fouling; compare with assumed; iterate if needed; check excess area 10–20 %. 10. Pressure drops: tube side ΔP = (4fLn/d_i + 4n)(ρv²/2); shell side (Kern) ΔP = fG_s²D_s(N_B + 1)/(2ρD_eφ). 11. Mechanical design and drawing: shell thickness, tube sheet, baffles, tie rods, nozzles, supports.

Design of high-pressure systems

Topics: Design of high-pressure vessels.

Thick cylinders and their construction

A vessel is thin-walled when D/t > 20; then hoop stress σ = PD/2t is uniform. In high-pressure service (ammonia and methanol synthesis at 150–300 bar, polyethylene at 1500–3000 bar, hydrocracking, isostatic presses) the wall becomes thick and the stress varies through it. Lamé’s solution for a cylinder under internal pressure P: σ_r = A − B/r², σ_θ = A + B/r², with σ_r = −P at r_i and 0 at r_o; maximum hoop stress at the bore σ_θ = P(K² + 1)/(K² − 1), K = r_o/r_i. Setting this to the allowable stress gives K = √((S + P)/(S − P)), so pressures approaching S cannot be held by a single thick shell however thick.

Failure theories: maximum principal stress (Rankine) for brittle materials; maximum shear stress (Tresca: σ_θ − σ_r ≤ S_y) and distortion energy (von Mises) for ductile steels. The Tresca form gives P = S_y(K² − 1)/(2K²) at first yield. Codes (ASME VIII Div. 2/3) use these with appropriate factors.

To use the wall efficiently the inner layers are pre-compressed: shrink-fit compound cylinders (an outer cylinder heated and shrunk on); autofrettage (over-pressurising so the bore yields and residual compression remains); multilayer vessels (many thin wrapped and welded layers, inherently leak-before-break); wire- or strip-wound vessels. Closures for high pressure: Bridgman self-sealing plugs, lens rings, wave rings, threaded or clamped closures. Materials: Cr–Mo low-alloy steels (resistance to hydrogen attack per the Nelson curves), with stainless overlay against corrosion.

  • Thin if D/t > 20.
  • Lamé: σ_θ,max = P(K² + 1)/(K² − 1).
  • K = √((S + P)/(S − P)).
  • Shrink fit, autofrettage, multilayer.

Example: An ammonia converter shell: P = 30 MPa, D_i = 1000 mm, allowable S = 180 MPa. Find the wall thickness by Lamé and compare with thin-wall theory.

  1. K = √((180 + 30)/(180 − 30)) = √1.4 = 1.183.
  2. t = r_i(K − 1) = 500 × 0.183 = 91.6 mm.
  3. Thin-wall (ASME form): t = PR/(S − 0.6P) = 30 × 500/(180 − 18) = 92.6 mm.

Answer: About 92 mm; at this K the two agree; at higher P/S Lamé is required.

Thick-walled cylinders (D/t < 20): Lamé stresses σ_r = A − B/r², σ_θ = A + B/r²; maximum hoop stress at the bore P(K² + 1)/(K² − 1); K = √((S + P)/(S − P)). Failure theories: Rankine, Tresca, von Mises. Efficient construction: shrink-fit compound cylinders, autofrettage, multilayer and wire-wound vessels. High-pressure closures and materials (Cr–Mo steels, Nelson curves for hydrogen service).

  • Inner fibre most stressed.
  • Adding thickness gives diminishing returns beyond K ≈ 2.
  • Autofrettage leaves residual compression at the bore.
  • Multilayer vessels leak before they break.
  • Hydrogen attack limits carbon steel at high T and pH₂.

Key formulas

  • σ_θ = P r_i²(r_o² + r²)/[r²(r_o² − r_i²)]
  • K = √((S + P)/(S − P))
  • P_yield (Tresca) = S_y(K² − 1)/(2K²)

Practice questions

A cylinder is usually treated as thick when

  1. D/t > 20
  2. D/t < 20
  3. P < 1 bar
  4. t < 1 mm
Show the answer

Answer: B. D/t < 20 Non-uniform stress.

Maximum hoop stress in a thick cylinder under internal pressure occurs at

  1. outer surface
  2. inner surface
  3. mid-wall
  4. ends only
Show the answer

Answer: B. inner surface Bore.

Autofrettage

  1. heats the vessel
  2. creates residual compressive stress at the bore
  3. adds a liner
  4. reduces thickness
Show the answer

Answer: B. creates residual compressive stress at the bore Controlled overpressure.

Radial stress at the outer free surface is

  1. P
  2. −P
  3. zero
  4. σ_θ
Show the answer

Answer: C. zero Free boundary.

For ductile steels the preferred failure theory is

  1. maximum principal stress
  2. maximum shear or distortion energy
  3. maximum strain only
  4. none
Show the answer

Answer: B. maximum shear or distortion energy Tresca or von Mises.

Theory questions

Derive Lamé’s equations for a thick cylinder subjected to internal pressure. (10 marks)

Show the model answer

Consider an element at radius r of thickness dr, unit length. Radial equilibrium: σ_θ − σ_r = r dσ_r/dr. Plane sections remain plane: longitudinal strain constant ⇒ σ_r + σ_θ = 2A (constant). Substituting: 2A − 2σ_r = r dσ_r/dr ⇒ d(r²σ_r)/dr = 2Ar ⇒ σ_r = A − B/r², σ_θ = A + B/r². Boundary conditions: σ_r(r_i) = −P, σ_r(r_o) = 0 ⇒ A = Pr_i²/(r_o² − r_i²), B = Pr_i²r_o²/(r_o² − r_i²). Hence σ_θ = [Pr_i²/(r_o² − r_i²)](1 + r_o²/r²), maximum at r_i: P(K² + 1)/(K² − 1). Longitudinal stress (closed ends) σ_z = Pr_i²/(r_o² − r_i²) = A. Design: set σ_θ,max = S ⇒ K = √((S + P)/(S − P)); t = r_i(K − 1).

Explain methods of pre-stressing high-pressure vessels. (5 marks)

Show the model answer

Because hoop stress is concentrated at the bore, the outer material is under-used. Pre-stressing puts the inner layers in residual compression so that, under pressure, the stress is more uniform. (1) Shrink fitting: outer cylinder bored slightly smaller than the inner’s OD, heated, slipped on and cooled; interface pressure compresses the inner shell. (2) Autofrettage: the vessel is pressurised beyond yield of the inner layers; on release the elastic outer layers squeeze the yielded bore, leaving residual compression (used for gun barrels and high-pressure tubing). (3) Multilayer construction: thin sheets wrapped and welded in tension around a core; each layer pre-stresses the ones beneath; no thick forgings needed; vent holes give leak detection. (4) Wire or strip winding under tension around a core.

Design of storage tanks

Topics: Design of storage tanks, head design and compensation design.

Tank shell, roof, heads and openings

Atmospheric storage tanks for oils and chemicals are designed to API 650 (or IS 803). The shell is made of courses (plate rings 1.8–2.5 m high) whose thickness falls towards the top because the hydrostatic hoop stress falls with height. The one-foot method gives t = 4.9D(H − 0.3)G/S_d + CA (mm, with D and H in metres, S_d in MPa) for the design condition, and t = 4.9D(H − 0.3)/S_t for the hydrotest; the larger governs, subject to a minimum nominal thickness of 5–10 mm by diameter. Bottom plates are lap-welded on a sand pad; roofs are self-supported cone or dome, supported cone with rafters, or floating roofs (pontoon, double-deck) for volatile products to cut vapour loss. Wind girders stiffen open-top and floating-roof tanks.

Pressure vessels and pressurised storage (LPG bullets and spheres) need formed heads. Thicknesses (IS 2825/ASME): torispherical t = 0.885PR_c/(SE − 0.1P) (crown radius = D, knuckle 6 %), 2:1 ellipsoidal t = PD/(2SE − 0.2P), hemispherical t = PR/(2SE − 0.2P) — half the shell thickness. Flat covers need t = CD√(P/S) and are only used for small diameters. Choice depends on pressure: torispherical up to ~15 bar, ellipsoidal to ~25 bar, hemispherical beyond.

Compensation (reinforcement) of openings: a hole removes metal that carried hoop stress. The area-replacement rule requires the removed area d × t_r to be replaced within a reinforcement zone (width d on each side, height 2.5t) by excess shell thickness, excess nozzle thickness, weld metal, and if needed a reinforcing pad (outside diameter up to 2d). Small openings (below ~50 mm in thin shells) may be exempt. Pads have a tell-tale hole to test welds.

  • API 650 one-foot method.
  • Shell courses thicker at the bottom.
  • Heads: torispherical, ellipsoidal, hemispherical, flat.
  • Area replacement for openings.

Example: A 20 m diameter × 12 m tank stores water (G = 1). S_d = 160 MPa, CA = 1.5 mm, S_t = 171 MPa. Find the bottom course thickness.

  1. Design: t = 4.9 × 20 × (12 − 0.3) × 1/160 + 1.5 = 7.17 + 1.5 = 8.67 mm.
  2. Hydrotest: t = 4.9 × 20 × 11.7/171 = 6.71 mm.
  3. Design governs: 8.67 → use 9 mm (above the 6 mm minimum for this diameter).

Answer: 9 mm bottom course.

Example: Compare head thicknesses for D = 2 m, P = 1 MPa, S = 120 MPa, E = 1.

  1. Torispherical: 0.885 × 1 × 2000/(120 − 0.1) = 14.8 mm.
  2. Ellipsoidal 2:1: 1 × 2000/(240 − 0.2) = 8.3 mm.
  3. Hemispherical: 1 × 1000/(240 − 0.2) = 4.2 mm.

Answer: 14.8, 8.3 and 4.2 mm: hemispherical is thinnest but costliest to form.

API 650 tanks: shell courses by the one-foot method t = 4.9D(H − 0.3)G/S_d + CA (design) and 4.9D(H − 0.3)/S_t (hydrotest), minimum thickness by diameter; bottom, fixed and floating roofs, wind girders. Heads: torispherical t = 0.885PR_c/(SE − 0.1P), ellipsoidal t = PD/(2SE − 0.2P), hemispherical t = PR/(2SE − 0.2P), flat t = CD√(P/S). Opening compensation by area replacement: d·t_r replaced by excess shell, nozzle, weld and pad within limits.

  • Floating roofs reduce evaporation losses.
  • Hydrotest uses water, no corrosion allowance.
  • Hemispherical head ≈ half the shell thickness.
  • Reinforcing pad up to 2d diameter.
  • Spheres for high-pressure gas storage.

Key formulas

  • t = 4.9D(H − 0.3)G/S_d + CA
  • t_tori = 0.885PR_c/(SE − 0.1P)
  • t_ellip = PD/(2SE − 0.2P)
  • A_required = d·t_r

Practice questions

In API 650 the shell thickness is checked at

  1. the top of each course
  2. 0.3 m above the bottom of each course
  3. mid-course
  4. the roof
Show the answer

Answer: B. 0.3 m above the bottom of each course One-foot method.

Which head is thinnest for the same pressure?

  1. flat
  2. torispherical
  3. ellipsoidal
  4. hemispherical
Show the answer

Answer: D. hemispherical Membrane stress PR/2t.

Floating roofs are used to

  1. support snow
  2. reduce vapour losses
  3. save steel
  4. heat the oil
Show the answer

Answer: B. reduce vapour losses No vapour space.

Opening compensation replaces

  1. the nozzle
  2. the area of metal removed
  3. the flange
  4. the gasket
Show the answer

Answer: B. the area of metal removed Area replacement rule.

Shell courses are thickest

  1. at the top
  2. at the bottom
  3. in the middle
  4. all equal
Show the answer

Answer: B. at the bottom Hydrostatic head.

Theory questions

Explain the design of an API 650 storage tank shell, bottom and roof. (10 marks)

Show the model answer

Data: capacity, diameter and height (H/D 0.4–1.2 economical), liquid SG, design and test stresses, corrosion allowance, wind and seismic data. Shell: number of courses = H/plate height; thickness of each course by the one-foot method t_d = 4.9D(H − 0.3)G/S_d + CA and t_t = 4.9D(H − 0.3)/S_t; take larger, round up, not below the minimum (5 mm for D < 15 m, 6 mm to 36 m, 8 mm to 60 m, 10 mm above); variable-design-point method for large tanks. Bottom: annular plates under the shell, lap-welded bottom plates ≥ 6 mm plus CA, sloped for drainage, on a compacted sand pad or ring wall. Roof: self-supported cone (slope 1:6 to 3:4) or dome, or supported cone with rafters and columns for large D; floating roof for volatile liquids with seals. Check wind (intermediate girders), overturning, uplift and anchoring, seismic (sloshing). Appurtenances: manholes, nozzles (reinforced), vents, ladders, gauging.

Explain compensation for openings in pressure vessels. (5 marks)

Show the model answer

An opening in a shell removes load-carrying metal and produces stress concentration (≈ 2.5–3 times the membrane stress at the edge of a hole in a cylinder). The area-compensation method requires the cross-sectional area removed, A = d·t_r (t_r = required shell thickness), to be replaced within a limit zone: parallel to the shell up to d on either side of the centre-line (or d/2 + t + t_n), and normal to the shell up to 2.5t or 2.5t_n. Available: A₁ excess shell = d(t − t_r); A₂ excess nozzle wall = 2 × 2.5t(t_n − t_rn); A₃ inward nozzle projection; A₄ weld area. If ΣA < A, add a reinforcing pad of area (A − ΣA), thickness usually ≤ shell thickness, outside diameter ≤ 2d. Alternatives: thicker nozzle necks, forged inserts. Openings below limits (e.g. ≤ 89 mm in shells ≤ 10 mm) need no calculation in ASME.

Drawing of phase-separation equipment

Topics: Drawing of physical separation equipment: hydrocyclones, packed towers, plate columns, electrostatic precipitators; schematic of pipe fittings and joints.

What each drawing must show

A hydrocyclone has a short cylindrical feed chamber with a tangential inlet, a long cone (included angle 10–20°), a vortex finder (overflow pipe) projecting down into the cylinder, and an apex (underflow) nozzle. Standard proportions relative to the cylinder diameter D_c: inlet ≈ D_c/7 to D_c/4, vortex finder ≈ D_c/3 to D_c/5, cylinder length ≈ D_c, cone length 2–5 D_c. The drawing shows sectional elevation, plan with the involute inlet, and flanged connections. The cut size scales as d₅₀ ∝ D_c^1.5/ (ΔP^0.25 Δρ^0.5) roughly — smaller cyclones cut finer.

A packed tower drawing shows: the shell with flanged sections, packing support plate (gas-injection type, > 75 % free area), random or structured packing, liquid distributor (orifice pan or trough, 40–100 drip points/m²), redistributors every 3–6 m (or 5–10 diameters for random packing), hold-down plate, demister at the top, gas inlet and liquid outlet with a seal. A plate column shows the trays with downcomers, weirs and active area, tray spacing, manholes every 10–20 trays, feed and draw-off nozzles, reflux inlet, reboiler return, skirt and base.

An electrostatic precipitator has discharge electrodes (wires or rigid spiked frames at −30 to −70 kV) between grounded collecting plates (spacing 250–400 mm), a gas distribution screen at the inlet, rappers to shake dust into hoppers, insulators and a transformer–rectifier. Efficiency follows Deutsch: η = 1 − exp(−wA/Q). Pipe fittings: elbows (90°, 45°, long and short radius), tees, reducers (concentric, eccentric), unions, couplings, caps, plugs; joints — threaded, socket-weld, butt-weld, flanged (weld-neck, slip-on, blind, lap-joint with gaskets and bolts); valves symbols (gate, globe, check, ball, butterfly). Drawings follow IS 10711/ISO conventions with first-angle projection.

  • Hydrocyclone: tangential inlet, vortex finder, apex.
  • Packed tower: support, distributor, redistributor, hold-down, demister.
  • ESP: discharge wires, collecting plates, rappers; Deutsch η.
  • Pipe joints: threaded, socket, butt-weld, flanged.

Example: An ESP treats 100 m³/s of flue gas with drift velocity 0.1 m/s. What plate area gives 99.5 % efficiency?

  1. η = 1 − exp(−wA/Q) ⇒ A = −(Q/w) ln(1 − η).
  2. A = −(100/0.1) × ln 0.005 = 1000 × 5.30.
  3. = 5300 m².

Answer: About 5300 m² of collecting plate.

Drawing practice for separation equipment: hydrocyclone (tangential inlet, cylindrical section, cone, vortex finder, apex; proportions to D_c), packed tower (support plate, distributors, redistributors every 3–6 m, hold-down, demister), plate column (trays, downcomers, weirs, spacing, manholes, nozzles, skirt), ESP (discharge electrodes, collecting plates, rappers, hoppers; Deutsch η = 1 − e^(−wA/Q)), and pipe fittings and joints (elbows, tees, reducers, flanges, threaded and welded joints, valve symbols).

  • Smaller cyclones cut finer particles.
  • Redistribute liquid to prevent wall flow.
  • Manholes every 10–20 trays.
  • ESP efficiency rises exponentially with plate area.
  • Weld-neck flanges for high pressure.

Key formulas

  • η = 1 − exp(−wA/Q)
  • d₅₀ ∝ D_c^1.5

Practice questions

The overflow pipe of a hydrocyclone is the

  1. apex
  2. vortex finder
  3. involute
  4. spigot
Show the answer

Answer: B. vortex finder Carries fines upward.

Liquid redistributors in packed towers prevent

  1. flooding
  2. wall flow and channelling
  3. foaming
  4. weeping
Show the answer

Answer: B. wall flow and channelling Liquid migrates to the wall.

ESP efficiency is given by

  1. Fenske
  2. Deutsch–Anderson
  3. Kremser
  4. Lamé
Show the answer

Answer: B. Deutsch–Anderson η = 1 − e^(−wA/Q).

A blind flange is used to

  1. join two pipes
  2. close the end of a pipe or nozzle
  3. reduce size
  4. change direction
Show the answer

Answer: B. close the end of a pipe or nozzle Closure.

Eccentric reducers are used on pump suctions to

  1. save cost
  2. avoid vapour pockets
  3. increase pressure
  4. reduce noise
Show the answer

Answer: B. avoid vapour pockets Flat side on top.

Theory questions

Draw a hydrocyclone and an electrostatic precipitator and explain their working. (10 marks)

Show the model answer

Hydrocyclone: slurry enters tangentially into the cylindrical section, forming a vortex; centrifugal force throws coarse, dense particles to the wall, where they spiral down the cone and leave through the apex (underflow); fine particles and most liquid move to the inner upward vortex and leave through the vortex finder (overflow). Cut size depends on diameter, pressure drop and density difference; proportions: inlet ≈ D_c/7, vortex finder ≈ D_c/5, cone angle 10–20°. ESP: dirty gas passes between earthed collecting plates with discharge electrodes at high negative voltage; corona discharge ionises gas; particles become charged and migrate to the plates; rappers knock collected dust into hoppers. Efficiency η = 1 − exp(−wA/Q) (Deutsch). Used for fly ash in power plants and cement kilns; efficiency above 99 % for fine particles with low pressure drop.

Draw and label a packed absorption tower and explain the function of each internal. (10 marks)

Show the model answer

Sketch: vertical shell with gas inlet at bottom, gas outlet at top through a mist eliminator; liquid inlet at top to a distributor; packed beds with support plates; redistributor between beds; hold-down plates; liquid outlet at bottom with a seal leg; manholes and handholes. Functions: support plate carries the packing weight and allows gas and liquid to pass with high free area (gas-injection type avoids premature flooding); liquid distributor spreads liquid uniformly (orifice, trough or spray), critical for structured packing; redistributor collects wall liquid and redistributes it every 3–6 m; hold-down plate stops packing from fluidising during surges (essential for plastic packing); demister removes entrained droplets; packing (Raschig rings, Pall rings, saddles, structured gauze/sheet) provides interfacial area with low pressure drop; bottom sump provides liquid hold-up for the pump.

Design of reactor vessels

Topics: Classification, material of construction, heating systems and design considerations.

Agitated reactor vessels

Reactors are classified by operation (batch, semi-batch, continuous), by flow pattern (stirred tank, tubular, packed bed, fluidised bed), by phases (homogeneous, gas–liquid, liquid–liquid, slurry, three-phase trickle bed) and by service (atmospheric, pressure, high-pressure autoclave). The workhorse of fine chemicals and pharmaceuticals is the jacketed stirred vessel (1–40 m³): cylindrical shell with dished heads, H/D ≈ 1–1.5, agitator with seal or magnetic drive, baffles (four, width D/10–D/12), nozzles for charging, sampling, venting, rupture disc and bottom discharge valve.

Material of construction follows corrosion data and product purity: carbon steel for neutral organics; SS 304/316L for most aqueous and organic service; glass-lined steel for acids and halides (but avoid thermal shock and HF, hot strong alkali); Hastelloy, titanium, tantalum or zirconium for severe corrosion; rubber or PTFE linings. Allowances for corrosion (1.5–3 mm) and cleaning, and compatibility with the reaction (catalytic metals, contamination) are considered.

Heating and cooling systems: conventional jacket with spiral baffles (low pressure, h ≈ 500–1500 W/m²K), dimple jacket (thin, higher pressure), half-pipe coil jacket (high pressure and velocity, good for thermal oil), internal coils (more area but cleaning problems), external loop exchangers, and direct steam injection. Batch heating time: t = (mc_p/UA) ln[(T_s − T₁)/(T_s − T₂)]. Design considerations: heat removal for exothermic reactions (runaway prevention, cooling capacity vs heat generation), mixing time and power (P = N_pρN³D⁵), pressure and temperature design with relief devices, foaming and vent sizing (DIERS), mechanical design (shell, jacket — check external pressure on the inner shell from jacket pressure), agitator shaft critical speed, supports (lugs, legs, skirt) and access for cleaning.

  • Classification by operation, flow, phases, pressure.
  • MOC: CS, SS 316L, glass-lined, Hastelloy, Ti.
  • Jackets: conventional, dimple, half-pipe; coils.
  • Heat-up time = (mc_p/UA) ln(ΔT₁/ΔT₂).

Example: A 5000 kg batch (c_p = 3.5 kJ/kgK) is heated from 25 to 90 °C by steam at 143 °C. U = 500 W/m²K, jacket area 10 m². How long?

  1. mc_p/UA = 5000 × 3500/(500 × 10) = 3500 s.
  2. ln[(143 − 25)/(143 − 90)] = ln(118/53) = 0.800.
  3. t = 3500 × 0.800 = 2800 s = 46.7 min.

Answer: About 47 minutes.

Reactor classification by operation, flow pattern, phases and pressure. Stirred jacketed vessels: H/D 1–1.5, dished heads, agitator, baffles, nozzles, relief. Materials: carbon steel, stainless, glass-lined, high alloys, linings with corrosion allowance. Heating and cooling: conventional, dimple and half-pipe jackets, internal coils, external loops; t = (mc_p/UA) ln[(T_s − T₁)/(T_s − T₂)]. Design considerations: heat removal and runaway, mixing power, pressure/temperature and relief, external-pressure check of the jacketed shell, supports and access.

  • Glass-lined steel for acids; not for HF or hot alkali.
  • Half-pipe jackets for high pressure.
  • Check inner shell for jacket pressure (external).
  • Cooling capacity must exceed heat generation.
  • Relief sizing for runaway (DIERS).

Key formulas

  • t = (mc_p/UA) ln[(T_s − T₁)/(T_s − T₂)]
  • P = N_pρN³D⁵
  • Q_gen = (−ΔH)rV

Practice questions

Glass-lined reactors should not be used with

  1. dilute HCl
  2. HF
  3. acetic acid
  4. water
Show the answer

Answer: B. HF Fluoride attacks glass.

A half-pipe jacket is preferred for

  1. very low pressure
  2. high-pressure heating media
  3. no heating
  4. cryogenic only
Show the answer

Answer: B. high-pressure heating media Strong small channels.

Batch heating time with condensing steam depends logarithmically on

  1. steam pressure only
  2. (T_s − T₁)/(T_s − T₂)
  3. agitator speed
  4. vessel height
Show the answer

Answer: B. (T_s − T₁)/(T_s − T₂) Unsteady balance.

Baffles in a stirred tank

  1. prevent vortexing and improve mixing
  2. reduce power to zero
  3. are only for cooling
  4. are not used
Show the answer

Answer: A. prevent vortexing and improve mixing Turn swirl into mixing.

A jacketed shell must also be checked for

  1. internal pressure only
  2. external pressure from the jacket
  3. wind only
  4. nothing
Show the answer

Answer: B. external pressure from the jacket Buckling.

Theory questions

Discuss the selection of materials of construction for reactor vessels. (5 marks)

Show the model answer

Considerations: corrosion resistance to reactants, products and cleaning agents at operating temperature; mechanical strength at temperature and pressure; product purity and catalytic effects (iron can discolour or catalyse side reactions); thermal conductivity and shock resistance; fabricability and weldability; cost and availability. Choices: carbon steel (cheap; neutral organics, alkalis), stainless steel 304/316L (most chemicals, food and pharma; avoid chlorides with stress), glass-lined steel (strong acids, halogens, high purity; avoid HF, hot alkali, thermal shock), Hastelloy and Inconel (chlorides, hot acids), titanium (wet chlorine, oxidising chlorides), lead or rubber linings, FRP for low temperature. A corrosion allowance is added to thickness.

Discuss the design considerations of a jacketed agitated batch reactor. (10 marks)

Show the model answer

Process: reaction kinetics and heat of reaction fix volume, batch cycle and heat duty; check that cooling capacity UAΔT exceeds peak heat generation with margin (runaway criteria, Semenov); mixing needs (blending, suspension, gas dispersion) set impeller type (turbine, pitched blade, anchor for viscous), speed and power P = N_pρN³D⁵. Geometry: H/D ≈ 1–1.5, baffles, dished heads, working volume 70–80 %. Material: from corrosion data; glass-lined, stainless or alloys; corrosion allowance. Heat transfer: jacket type, area, U from inside (agitated) and jacket-side coefficients, heat-up and cool-down times; internal coils if area is short. Mechanical: shell and head thickness for internal pressure, external pressure from jacket or vacuum (stiffeners), jacket thickness, nozzles reinforced, agitator shaft and seal (mechanical seal, magnetic drive for toxic service), supports (lugs or legs), weights. Safety: relief valve or rupture disc sized for runaway, temperature and pressure instrumentation, interlocks, inerting, earthing. Drawing: elevation with jacket, agitator, nozzles schedule.

Notes, examples and questions were written for this studio; the prescribed books are listed in the studio for reference.

Frequently asked questions

What is the Process Equipment Design-I (2018) Studio?

Exchangers, thick shells and tanks, drawn to code. Shell-and-tube, double-pipe and condenser design by Kern, thick-walled high-pressure vessels (Lamé), API 650 storage-tank courses, heads and opening compensation, separation-equipment drawings and jacketed reactors from the ASTU CHE181701 syllabus (2018-19 scheme).

What can I do in the Process Equipment Design-I (2018) Studio?

Kern design of exchangers, condensers and evaporators; Thick cylinders and high-pressure vessels; Tank shells, heads and nozzle reinforcement; Jacketed reactor vessels.

Is the Process Equipment Design-I (2018) Studio free?

Yes. It is free and runs in your browser with no sign-up.

Open the interactive studio →