IITIAN1997 STUDIO

Petroleum Refining & Petrochemicals

Crude to petrol, polymers and beyond.

Open the interactive studio →

Crude evaluation, API and Watson K, desalting, atmospheric and vacuum distillation, FCC, hydroprocessing, reforming, alkylation, Claus and MEROX, petrochemicals, Indmax and bio-refineries from the ASTU CHE241402 syllabus.

What is inside

  • Crude evaluation, API gravity and TBP cuts
  • Distillation, FCC, hydrotreating and reforming
  • Amine, Claus, MEROX, hydrogen and lube oils
  • Petrochemicals, Indmax and ethanol

Syllabus: ASTU CHE241402 Petroleum Refining and Petrochemicals, semester 4, NEP 2020 (2024-25 onwards). Official syllabus PDF.

Introduction to the petroleum refinery

Topics: Indian petroleum refineries, prospects and future; composition of crude oil; classification and evaluation of crude oil; properties and testing of petroleum products.

Indian refineries, crude composition and crude evaluation

India is one of the world’s largest refiners, with about two dozen refineries and a capacity of roughly 250 million tonnes a year. Public-sector companies (IOCL, BPCL, HPCL, ONGC-MRPL, CPCL, NRL) own most of them; Reliance’s Jamnagar complex is the largest single refining site in the world. Assam holds the oldest: Digboi (1901), followed by Guwahati (1962), Bongaigaon and Numaligarh, which is being expanded. Growth now comes from petrochemical integration, cleaner (BS-VI) fuels, ethanol blending and biofuels.

Crude oil is a mixture of hydrocarbons: paraffins (straight and branched alkanes), naphthenes (cycloalkanes) and aromatics, with small amounts of sulphur compounds (mercaptans, sulphides, thiophenes), nitrogen and oxygen compounds, metals (nickel, vanadium), salts and water. Olefins are essentially absent from crude; they are made in cracking units. Crudes are classified by their dominant family (paraffinic, naphthenic, intermediate or aromatic base, often via the Watson factor K = T_b^(1/3)/SG), by density (API gravity = 141.5/SG − 131.5: light > 31.1, medium 22.3–31.1, heavy < 22.3) and by sulphur (sweet < 0.5 wt %, sour above).

A crude assay evaluates a crude before purchase: API gravity, sulphur, pour point, viscosity, salt, water and sediment, Conradson carbon residue, metals and acid number, plus a true-boiling-point (TBP) distillation that gives the yield and properties of each cut. Products are tested against specifications: density, distillation range, flash point (safety in storage), Reid vapour pressure and octane number for petrol, smoke point and freezing point for kerosene and jet fuel, cetane number, cloud and pour point and sulphur for diesel, viscosity and viscosity index for lubes, and penetration and softening point for bitumen.

  • API = 141.5/SG − 131.5; water = 10 °API.
  • Watson K: paraffinic ≈ 12.5–13, naphthenic ≈ 11–11.5, aromatic < 10.5.
  • Sweet crude < 0.5 wt % S; sour above.
  • Flash point: storage safety; RVP: volatility; smoke point: kerosene flame quality.

Example: A crude has a specific gravity of 0.876. Find its API gravity and class.

  1. °API = 141.5/0.876 − 131.5.
  2. = 161.53 − 131.5 = 30.0.

Answer: 30 °API: a medium crude (22.3–31.1).

Example: A cut has SG 0.82 and mean average boiling point 200 °C. Find its Watson K and say what kind of hydrocarbon dominates.

  1. T_b = (200 + 273.15) × 1.8 = 851.7 °R.
  2. T_b^(1/3) = 9.479.
  3. K = 9.479/0.82 = 11.56.

Answer: K ≈ 11.6: between naphthenic and intermediate, so naphthenes are significant.

Crude oil and its distillation

Crude oil is a mixture of hydrocarbons (paraffins, naphthenes, aromatics) with sulphur, nitrogen and metal compounds. API gravity = 141.5/SG − 131.5: light crudes have high API. Atmospheric distillation separates gas, naphtha, kerosene, diesel and residue; the residue goes to a vacuum column to recover heavy gas oils without cracking them.

  • °API = 141.5/SG − 131.5
  • Atmospheric then vacuum distillation
  • Products from light to heavy: LPG → bitumen

Example: A crude has SG 0.85. Find its API gravity.

  1. °API = 141.5/0.85 − 131.5.
  2. ≈ 35 °API (a light-to-medium crude).

Answer: ≈ 35 °API

Example: Why is the atmospheric residue distilled under vacuum?

  1. Its components boil above the temperature where they start to crack.
  2. Lower pressure lowers the boiling points, so they distil without cracking.

Answer: To avoid thermal cracking

India refines about 250 Mt/y in two dozen refineries (Jamnagar largest; Digboi, 1901, the oldest still working). Crude is a mixture of paraffins, naphthenes and aromatics with sulphur, nitrogen, metals, salt and water. Crudes are classified by base (Watson K), density (API gravity) and sulphur (sweet/sour) and evaluated by an assay including a TBP distillation. Products are tested for density, distillation, flash point, RVP, octane, smoke point, cetane, cloud and pour points, viscosity and bitumen penetration and softening point.

  • Olefins are not present in crude oil; cracking makes them.
  • Higher API = lighter crude = more light products.
  • Conradson carbon indicates coke-forming tendency.
  • Ni and V poison cracking catalysts.

Key formulas

  • °API = 141.5/SG − 131.5
  • K = T_b^(1/3)/SG (T_b in °R)
  • Diesel index = AP(°F) × °API/100

Practice questions

Which hydrocarbon family is essentially absent from crude oil?

  1. Paraffins
  2. Naphthenes
  3. Aromatics
  4. Olefins
Show the answer

Answer: D. Olefins Formed by cracking.

A crude of 10 °API has the density of

  1. air
  2. water
  3. mercury
  4. propane
Show the answer

Answer: B. water SG = 1.

A Watson K of 12.8 indicates a

  1. paraffinic crude
  2. aromatic crude
  3. naphthenic crude
  4. asphalt
Show the answer

Answer: A. paraffinic crude High K.

A sour crude contains more than about

  1. 0.5 wt % sulphur
  2. 5 wt % water
  3. 1 % salt
  4. 10 % aromatics
Show the answer

Answer: A. 0.5 wt % sulphur Sulphur.

The oldest operating refinery in India is at

  1. Jamnagar
  2. Digboi
  3. Barauni
  4. Mathura
Show the answer

Answer: B. Digboi 1901.

Theory questions

Describe the composition of crude oil and the methods of classifying crudes. (5 marks)

Show the model answer

Hydrocarbons: paraffins (n- and iso-alkanes), naphthenes (cyclopentanes, cyclohexanes), aromatics (benzene to polynuclear), no olefins. Non-hydrocarbons: sulphur (mercaptans, sulphides, thiophenes), nitrogen (pyridines, pyrroles), oxygen (naphthenic acids), metals (Ni, V in porphyrins), salts, water and sediment. Classification: by base using the Watson characterisation factor (paraffinic, intermediate, naphthenic, aromatic) or the US Bureau of Mines correlation index; by API gravity (light, medium, heavy); by sulphur (sweet, sour).

What is a crude assay? List the tests and explain the use of the TBP curve. (5 marks)

Show the model answer

A crude assay is a set of laboratory tests used to value a crude and plan its processing: API gravity, sulphur, pour point, viscosity, Reid vapour pressure of the whole crude, salt, BS&W, Conradson carbon, asphaltenes, metals, acid number and a TBP distillation (with ASTM distillations and properties of each cut). The TBP curve (volume % distilled vs temperature in a high-efficiency column) gives the yield of each product between chosen cut points; property curves for each cut (sulphur, density, octane, cetane, pour point) show whether products meet specifications.

Processing of crude oil

Topics: Dehydration and desalting; atmospheric and vacuum distillation; coking, visbreaking and thermal cracking; solvent deasphalting; fluidised catalytic cracking; hydroprocessing: hydrotreating and hydrocracking; catalytic reforming; alkylation and isomerisation.

Primary processing: desalting, atmospheric and vacuum distillation

Crude arrives with brine droplets and sediment. Salts (mainly NaCl, MgCl₂, CaCl₂) hydrolyse in the furnace to HCl, which corrodes overhead equipment, and also foul exchangers and poison catalysts. In the desalter the crude is heated to about 120–150 °C, mixed with 3–8 % wash water through a mixing valve to dissolve the salt, and the emulsion is broken in a large horizontal vessel by an electric field (electrostatic desalting); salt content falls to a few ppm and the brine is drained.

The atmospheric distillation unit (crude distillation unit, the refinery’s “mother unit”) heats the desalted crude in a pre-heat train and a fired furnace to about 350–370 °C, the highest temperature it can stand without cracking, and flashes it into a column of 30–50 trays with stripping steam at the bottom. Products are drawn from the top down: gas and LPG, light and heavy naphtha, kerosene, light and heavy diesel (gas oil), and reduced crude at the bottom. Side strippers remove light ends from each side product, and pump-around circuits remove heat.

The reduced crude still contains valuable gas oil boiling up to about 550–565 °C, which would crack if heated at atmospheric pressure. The vacuum distillation unit operates at about 25–100 mmHg absolute at the flash zone, so these components boil at lower temperatures: vacuum gas oils (feed to FCC or hydrocracking, or lube base stocks) are drawn off and vacuum residue leaves the bottom for coking, visbreaking, deasphalting or bitumen.

  • Desalter: 120–150 °C, wash water, electrostatic field.
  • CDU furnace outlet ≈ 350–370 °C.
  • VDU flash zone ≈ 25–100 mmHg abs.
  • VGO → FCC/hydrocracker; vacuum residue → coker, visbreaker, SDA, bitumen.

Conversion processes: thermal, catalytic and hydrogen addition

Thermal processes crack residues by heat alone through free radicals. Visbreaking is mild cracking (about 450–480 °C, short time) to reduce the viscosity of residue so that less cutter stock is needed for fuel oil. Delayed coking cracks residue completely at about 480–500 °C in large drums, producing gas, naphtha, gas oils and solid petroleum coke; drums alternate between filling and decoking. Solvent deasphalting uses propane or butane to dissolve the paraffinic part of vacuum residue (deasphalted oil, a cracking or lube feed) and reject asphaltenes as pitch.

Fluid catalytic cracking (FCC) cracks vacuum gas oil over a fine zeolite catalyst in a riser reactor at about 500–540 °C in a few seconds, through carbocation mechanisms that favour branched and aromatic products: high-octane gasoline, LPG rich in propylene and butylenes, light cycle oil and slurry. Coke deposited on the catalyst is burnt in the regenerator at about 680–730 °C; the hot catalyst returns to the riser and supplies the heat for cracking, so the unit is in heat balance.

Hydroprocessing adds hydrogen over metal-sulphide catalysts. Hydrotreating (CoMo, NiMo, about 300–400 °C, 30–150 bar) removes sulphur, nitrogen and metals and saturates olefins without much change of boiling range; it makes BS-VI fuels possible. Hydrocracking (bifunctional catalysts, higher pressure 100–200 bar) both cracks and hydrogenates, converting VGO into very clean diesel, kerosene and naphtha. Catalytic reforming (Pt–Re on chlorided alumina, about 500 °C, low pressure, in fixed-bed or continuous-regeneration units) converts low-octane naphtha into high-octane reformate by dehydrogenating naphthenes and dehydrocyclising paraffins, releasing hydrogen. Alkylation joins isobutane and light olefins over HF or H₂SO₄ to give alkylate, an ideal high-octane, low-aromatic petrol component; isomerisation turns n-pentane and n-hexane into branched isomers over Pt catalysts.

  • Visbreaking: lower viscosity; coking: residue → coke + liquids.
  • FCC: VGO → gasoline + LPG (propylene); heat balance with coke burning.
  • Hydrotreating removes S, N, metals; hydrocracking converts VGO.
  • Reforming: naphthenes → aromatics + H₂; alkylation: iC₄ + olefin → iso-octane.

Example: An FCC unit converts 100 m³ of VGO into gas, LPG, 55 m³ gasoline, 15 m³ light cycle oil and 7 m³ slurry. What is the conversion?

  1. Conversion is defined on material boiling below the gasoline end point (≈ 221 °C).
  2. Conversion = 100 − (LCO + slurry) = 100 − (15 + 7).

Answer: 78 vol %.

Example: A reformer dehydrogenates 1000 kg/h of methylcyclohexane (C₇H₁₄, M = 98.19) completely to toluene (M = 92.14). How much toluene and hydrogen is made?

  1. C₇H₁₄ → C₇H₈ + 3H₂.
  2. Moles = 1000/98.19 = 10.18 kmol/h.
  3. Toluene = 10.18 × 92.14 = 938 kg/h; H₂ = 30.55 kmol/h = 61.6 kg/h = 685 Nm³/h.
  4. Check: 938 + 61.6 ≈ 1000 kg/h.

Answer: 938 kg/h of toluene and about 685 Nm³/h of hydrogen.

Example: An alkylation unit reacts 100 kmol/h of butene with isobutane at an isobutane/olefin ratio of 8. How much isobutane is recycled and how much alkylate (C₈H₁₈, M = 114.2) is made?

  1. i-C₄H₁₀ + C₄H₈ → C₈H₁₈; 100 kmol/h of isobutane reacts.
  2. Isobutane fed to the reactor = 8 × 100 = 800 kmol/h; recycle = 800 − 100 = 700 kmol/h (plus any make-up).
  3. Alkylate = 100 × 114.2 = 11 420 kg/h.

Answer: About 700 kmol/h recycled and 11.4 t/h of alkylate; the large excess suppresses olefin polymerisation.

Conversion processes

Cracking breaks large molecules: thermal cracking and visbreaking by heat; fluid catalytic cracking (FCC) over zeolite catalyst gives high-octane gasoline; hydrocracking uses hydrogen and gives clean middle distillates. Coking turns residue into coke and lighter products.

Catalytic reforming (platinum catalyst) turns naphtha into aromatics, raising octane and yielding hydrogen; alkylation joins isobutane and olefins into high-octane alkylate; isomerisation turns straight chains into branched ones.

  • FCC: zeolite, makes gasoline
  • Reforming: Pt catalyst, aromatics, H₂
  • Branched and aromatic = higher octane

Example: Which refinery process makes aromatics and hydrogen from naphtha?

  1. Dehydrogenation of naphthenes over platinum produces aromatics and H₂.
  2. This is catalytic reforming.

Answer: Catalytic reforming

Example: A fuel knocks like a blend of 70 % iso-octane and 30 % n-heptane. What is its octane number?

  1. Octane number = % iso-octane in the matching reference blend.
  2. 70.

Answer: 70

Desalting removes salt (to prevent HCl corrosion) by washing and electrostatic separation. Atmospheric distillation (mother unit) splits crude into gas, LPG, naphtha, kerosene, diesel and reduced crude; vacuum distillation recovers gas oils from the residue without cracking. Visbreaking, delayed coking and solvent deasphalting upgrade residue. FCC cracks VGO to gasoline and LPG with a coke-burning heat balance. Hydrotreating removes S, N and metals; hydrocracking converts VGO to middle distillates. Catalytic reforming raises naphtha octane and makes hydrogen; alkylation and isomerisation make branched high-octane petrol components.

  • CDU furnace outlet is limited to about 370 °C to avoid cracking.
  • Vacuum lowers boiling points so heavy oils distil without cracking.
  • FCC is the main source of refinery propylene.
  • Reformer hydrogen feeds hydrotreaters.

Key formulas

  • FCC conversion = 100 − (LCO + slurry) vol %
  • C/O = heat needed/(c_p,cat ΔT)
  • C₇H₁₄ → C₇H₈ + 3H₂ (reforming)
  • iC₄H₁₀ + C₄H₈ → C₈H₁₈ (alkylation)

Practice questions

The main purpose of desalting crude is to prevent

  1. octane loss
  2. HCl corrosion and fouling
  3. coke formation in FCC
  4. high RVP
Show the answer

Answer: B. HCl corrosion and fouling Salts hydrolyse to HCl.

Vacuum distillation is used because heavy fractions would otherwise

  1. freeze
  2. crack at the required temperature
  3. evaporate too fast
  4. react with steam
Show the answer

Answer: B. crack at the required temperature Lower boiling points under vacuum.

The heat for cracking in an FCC riser comes mainly from

  1. a fired heater on the riser
  2. hot regenerated catalyst
  3. steam
  4. electric heaters
Show the answer

Answer: B. hot regenerated catalyst Heat balance.

Catalytic reforming mainly

  1. raises naphtha octane and produces hydrogen
  2. removes sulphur
  3. makes coke
  4. cracks residue
Show the answer

Answer: A. raises naphtha octane and produces hydrogen Aromatisation.

Alkylate is made from

  1. benzene and ethylene
  2. isobutane and light olefins
  3. methane and steam
  4. naphtha and hydrogen
Show the answer

Answer: B. isobutane and light olefins Acid catalysed.

Delayed coking converts residue into lighter products and

  1. bitumen
  2. petroleum coke
  3. alkylate
  4. reformate
Show the answer

Answer: B. petroleum coke Solid coke in drums.

Theory questions

With a neat sketch, describe atmospheric and vacuum distillation of crude oil. (6 marks)

Show the model answer

Desalted crude is preheated by product streams, heated in a fired furnace to ≈ 350–370 °C and enters the flash zone of a 30–50 tray atmospheric column with stripping steam at the bottom. Vapour rises and is fractionated; products are withdrawn: overhead gas and naphtha (condensed, reflux returned), side draws of kerosene, light and heavy gas oil through side strippers, pump-arounds removing heat. Reduced crude from the bottom is reheated to ≈ 400 °C and flashed in a vacuum column (25–100 mmHg absolute, steam ejectors), giving light and heavy vacuum gas oils as side draws (FCC/hydrocracker feed or lube stocks) and vacuum residue at the bottom (coker, visbreaker, SDA, bitumen). Vacuum lowers boiling points so cracking is avoided.

Describe the FCC process and explain how the unit is kept in heat balance. (6 marks)

Show the model answer

Preheated VGO is atomised into the bottom of a riser where it meets hot regenerated zeolite catalyst (≈ 700 °C); it vaporises and cracks in 2–4 s at ≈ 500–540 °C. Cyclones in the reactor separate catalyst from cracked vapours, which go to the main fractionator (gas, LPG, gasoline, LCO, slurry). Spent catalyst is steam-stripped and flows to the regenerator, where air burns the coke (to CO₂/CO) at 680–730 °C; flue gas goes through cyclones, CO boiler or expander. Heat balance: the heat released by burning coke = heat carried by circulating catalyst = heat to vaporise and crack the feed + losses. If more coke forms, the regenerator gets hotter, the catalyst circulation needed (C/O) falls and conversion falls, so the unit regulates itself.

Compare hydrotreating and hydrocracking. (4 marks)

Show the model answer

Both add hydrogen over sulphided metal catalysts. Hydrotreating: CoMo/NiMo on alumina, 300–400 °C, 30–150 bar, removes S, N, O, metals and saturates olefins with little cracking (< 10 %); feeds are naphtha, kerosene, diesel, VGO; purpose is product quality and catalyst protection. Hydrocracking: bifunctional (metal + acidic zeolite/amorphous silica-alumina), 350–430 °C, 100–200 bar, large hydrogen consumption; cracks VGO or residue into lighter, saturated, very low-sulphur diesel, jet fuel and naphtha; purpose is conversion.

Purification and treatment of petroleum products

Topics: Production and treatment of LPG and CNG; amine treating; sulphur recovery; MEROX process; hydrogen generation; extraction of aromatics; recovery of olefins; additives and odorants; solvent dewaxing; removal of objectionable gases and elements; lube oil processing.

Gas treating, sulphur recovery and sweetening

LPG (mainly propane and butane) comes from crude distillation, FCC and reformer gas plants and from natural-gas processing. It must be sweetened and dried, and a stenching agent (ethyl mercaptan) is added so leaks can be smelt. CNG is natural gas (mostly methane) dried and compressed to about 200–250 bar for vehicles. Refinery fuel gas and LPG streams contain H₂S and CO₂, removed by amine treating: the gas contacts a lean aqueous amine (MEA, DEA or MDEA) in an absorber; the rich amine is regenerated by steam stripping, releasing acid gas.

The acid gas (H₂S) goes to the Claus sulphur recovery unit. One third of the H₂S is burnt to SO₂ in a reaction furnace; the remaining H₂S reacts with the SO₂ (2H₂S + SO₂ → 3S + 2H₂O) thermally and then in two or three catalytic converters over alumina, with sulphur condensed between stages. Recovery is about 95–98 %; tail-gas treating (e.g. hydrogenating everything back to H₂S and recycling) raises it above 99.5 %.

Light distillates (LPG, naphtha, kerosene/ATF) contain mercaptans, which smell and corrode. The MEROX process extracts mercaptans into caustic soda or converts them in place over a cobalt phthalocyanine catalyst with air into disulphides: 4RSH + O₂ → 2RSSR + 2H₂O (sweetening). Heavier streams are hydrotreated instead.

  • Amines: MEA (fast, unselective), DEA, MDEA (selective for H₂S).
  • Claus: burn ⅓ of H₂S, then 2H₂S + SO₂ → 3S + 2H₂O.
  • MEROX: 4RSH + O₂ → 2RSSR + 2H₂O.
  • Odorant (ethyl mercaptan) added to LPG for safety.

Example: A gas contains 100 kmol/h of H₂S. A 15 wt % MEA solution (M = 61.08) is loaded to 0.35 mol H₂S per mol MEA. Find the MEA and solution circulation.

  1. MEA = 100/0.35 = 285.7 kmol/h.
  2. Mass of MEA = 285.7 × 61.08 = 17 450 kg/h.
  3. Solution = 17 450/0.15 = 116 300 kg/h.

Answer: About 116 t/h of 15 % MEA solution.

Example: Kerosene (50 m³/h, 800 kg/m³) contains 200 wt ppm mercaptan sulphur. How much air does MEROX sweetening need (stoichiometric)?

  1. S = 50 × 800 × 200 × 10⁻⁶ = 8 kg/h = 0.2495 kmol/h RSH.
  2. 4RSH + O₂ → 2RSSR + 2H₂O: O₂ = 0.2495/4 = 0.0624 kmol/h.
  3. Air = 0.0624/0.21 = 0.297 kmol/h ≈ 6.7 Nm³/h.

Answer: About 6.7 Nm³/h of air (in practice a small excess).

Hydrogen, aromatics, olefins and lube oils

Hydrogen demand rises with tighter fuel specifications. Besides reformer hydrogen, refineries build steam methane reformers: desulphurised natural gas or naphtha reacts with steam over nickel catalyst at about 800–900 °C (CH₄ + H₂O → CO + 3H₂, strongly endothermic), followed by water-gas shift (CO + H₂O → CO₂ + H₂) and pressure-swing adsorption to give 99.9 % hydrogen.

Aromatics (benzene, toluene, xylenes: BTX) are recovered from reformate or pyrolysis gasoline by liquid–liquid extraction or extractive distillation with selective polar solvents such as sulfolane, N-methylpyrrolidone or glycols, followed by fractionation. Light olefins (ethylene, propylene) are recovered from FCC and cracker gases by compression, cooling and cryogenic fractionation; propylene is split from propane in a large superfractionator.

Lube oil base stocks are made from vacuum distillates and deasphalted oil. Solvent extraction (furfural, NMP, phenol) removes aromatics to raise the viscosity index; solvent dewaxing (methyl ethyl ketone–toluene, chilled to about −20 °C) crystallises and filters out waxes to lower the pour point; hydrofinishing improves colour and stability. Modern plants use hydrocracking and catalytic dewaxing (isomerising waxes) instead. Additives (antioxidants, detergents, pour-point depressants, viscosity-index improvers, cetane improvers, anti-knock agents) adjust finished products.

  • SMR: CH₄ + H₂O → CO + 3H₂, then shift and PSA.
  • BTX extraction: sulfolane, NMP, glycols.
  • Dewaxing: MEK–toluene, chill and filter.
  • Viscosity index: how little viscosity changes with temperature.

Products, specifications and treating

Petrol is rated by octane number (resistance to knocking); diesel by cetane number (ease of self-ignition; BS-VI diesel requires at least 51). Kerosene by smoke point; lubricating oils by viscosity index; bitumen by penetration.

Treating removes impurities: hydrodesulphurisation (R–SH + H₂ → R–H + H₂S) for low-sulphur fuels (BS-VI allows 10 ppm sulphur), sweetening converts mercaptans, and amine units remove H₂S from gas.

  • Petrol: octane; diesel: cetane
  • BS-VI: 10 ppm sulphur
  • HDS: R–SH + H₂ → R–H + H₂S

Example: Write the hydrodesulphurisation reaction of a mercaptan.

  1. Hydrogen breaks the C–S bond over a Co–Mo catalyst.
  2. R–SH + H₂ → R–H + H₂S.

Answer: R–SH + H₂ → R–H + H₂S

LPG and CNG are sweetened, dried and odorised. Amine treating (MEA, DEA, MDEA) removes H₂S and CO₂; the Claus process converts H₂S into sulphur (95–98 %, more with tail-gas treating). MEROX extracts or oxidises mercaptans to disulphides. Hydrogen comes from reformers and steam methane reforming with shift and PSA. Aromatics are extracted with sulfolane or NMP; olefins recovered by cryogenic fractionation. Lube oils: solvent extraction (VI), solvent dewaxing (pour point), hydrofinishing; additives finish all products.

  • MDEA is selective for H₂S over CO₂.
  • Claus needs exactly one third of the H₂S burnt.
  • Sweetening converts but does not remove sulphur; hydrotreating removes it.
  • Dewaxing lowers pour point; extraction raises VI.

Key formulas

  • 2H₂S + SO₂ → 3S + 2H₂O
  • 4RSH + O₂ → 2RSSR + 2H₂O
  • CH₄ + H₂O → CO + 3H₂ ; CO + H₂O → CO₂ + H₂

Practice questions

The odorant added to LPG is

  1. methane
  2. ethyl mercaptan
  3. benzene
  4. MTBE
Show the answer

Answer: B. ethyl mercaptan Smell for leak detection.

MEROX treatment converts mercaptans into

  1. H₂S
  2. disulphides
  3. sulphur
  4. SO₂
Show the answer

Answer: B. disulphides Oxidation.

In the Claus process the fraction of H₂S burnt to SO₂ is

  1. all
  2. one half
  3. one third
  4. one tenth
Show the answer

Answer: C. one third 2 : 1 ratio.

Solvent dewaxing is done to lower the

  1. viscosity index
  2. pour point
  3. flash point
  4. octane
Show the answer

Answer: B. pour point Remove wax.

Sulfolane is used to

  1. extract aromatics
  2. remove water
  3. make hydrogen
  4. dewax oils
Show the answer

Answer: A. extract aromatics BTX extraction.

Theory questions

Describe amine treating and the Claus sulphur recovery process. (6 marks)

Show the model answer

Sour gas enters the bottom of an absorber and contacts lean amine (MEA/DEA/MDEA, 15–50 wt %) flowing down; H₂S and CO₂ react reversibly to form salts. Sweet gas leaves the top. Rich amine is flashed, heated against lean amine and stripped with steam in a regenerator (≈ 120 °C), releasing acid gas; lean amine is cooled and returned. The acid gas goes to the Claus unit: in the reaction furnace (≈ 1000–1300 °C) one third of the H₂S burns to SO₂ and part of the Claus reaction occurs; a waste-heat boiler cools the gas, sulphur is condensed, and the gas is reheated through two or three alumina catalytic converters (2H₂S + SO₂ → 3S + 2H₂O) with condensers after each. Tail gas is incinerated or treated (SCOT) for > 99.5 % recovery.

Explain the manufacture of lube oil base stocks from vacuum distillates. (5 marks)

Show the model answer

Vacuum distillates (and deasphalted oil from propane deasphalting of vacuum residue) are solvent-extracted with furfural/NMP to remove aromatics and polar compounds, raising the viscosity index and oxidation stability. The raffinate is dewaxed by mixing with MEK–toluene, chilling to −10 to −25 °C and filtering out wax crystals on rotary vacuum filters, lowering pour point. Hydrofinishing (mild hydrotreating) improves colour and stability. Alternatively hydrocracking plus catalytic isodewaxing gives Group II/III base oils. Additives are blended to make finished lubricants.

Petrochemicals

Topics: Introduction and classification of petrochemicals; chemicals from natural gas and synthesis gas; chemicals from olefins: ethylene, propylene and butylene derivatives; aromatics; intermediates for synthetic fibres and plastics.

From feedstocks to building blocks

Petrochemicals are chemicals made from petroleum or natural gas. They are usually classified as first-generation building blocks (synthesis gas, methanol, ammonia; ethylene, propylene, butadiene; benzene, toluene, xylenes), intermediates (ethylene oxide, ethylene glycol, vinyl chloride, styrene, cumene, phenol, acrylonitrile, caprolactam, terephthalic acid) and end products (polymers, fibres, rubbers, detergents, solvents).

Natural gas and synthesis gas (CO + H₂ from steam reforming or gasification) give ammonia (Haber–Bosch), methanol (Cu/ZnO, about 250 °C, 50–100 bar), and from methanol formaldehyde, acetic acid (carbonylation) and olefins (methanol-to-olefins). Light olefins come mainly from steam cracking of ethane, LPG or naphtha at about 800–850 °C with steam dilution and residence times under a second, followed by quenching, compression and cryogenic separation; FCC adds propylene.

Ethylene derivatives: polyethylene (LDPE by high-pressure free-radical polymerisation, HDPE and LLDPE with Ziegler–Natta or metallocene catalysts), ethylene oxide (silver catalyst, direct oxidation) and ethylene glycol, ethylene dichloride and vinyl chloride for PVC, ethylbenzene and styrene, ethanol. Propylene derivatives: polypropylene, acrylonitrile (ammoxidation), propylene oxide, cumene (benzene + propylene) and from it phenol and acetone, isopropanol, oxo alcohols. Butylene and butadiene derivatives: synthetic rubbers (SBR, polybutadiene), MTBE (methanol + isobutylene), butanols. Aromatics: benzene → ethylbenzene/styrene, cumene/phenol, cyclohexane → caprolactam (nylon 6) and adipic acid (nylon 6,6), linear alkylbenzene (detergents); p-xylene → purified terephthalic acid (PTA) → polyester (PET) with ethylene glycol.

  • Building blocks: syngas, methanol; C₂=, C₃=, C₄; BTX.
  • Ethylene → PE, EO/MEG, EDC/VCM/PVC, styrene.
  • Propylene → PP, acrylonitrile, cumene/phenol, PO.
  • p-Xylene → PTA → PET (with MEG).

Example: Ethylene is oxidised to ethylene oxide (C₂H₄ + ½O₂ → C₂H₄O) with 80 % selectivity (the rest burns). How much ethylene is consumed per tonne of EO?

  1. EO: 1000/44.05 = 22.70 kmol.
  2. Ethylene reacted = 22.70/0.80 = 28.38 kmol.
  3. Mass = 28.38 × 28.05 = 796 kg.

Answer: About 0.80 t of ethylene per tonne of EO (0.64 t would be needed at 100 % selectivity).

Example: Ethane is cracked (C₂H₆ → C₂H₄ + H₂) with 65 % conversion per pass and 80 mol % selectivity to ethylene; unconverted ethane is recycled. Find the ethylene per pass and the ultimate mass yield.

  1. Per 100 kmol ethane fed: 65 react, 0.8 × 65 = 52 kmol ethylene = 1459 kg.
  2. With recycle all ethane eventually reacts at 80 % selectivity.
  3. Ultimate yield = 0.80 × 28.05/30.07 = 0.746 kg ethylene per kg ethane.

Answer: 52 kmol per pass; about 75 wt % ultimate yield.

Example: p-Xylene is oxidised to terephthalic acid: C₈H₁₀ + 3O₂ → C₈H₆O₄ + 2H₂O. How much p-xylene and oxygen are needed per tonne of PTA at 100 % yield?

  1. PTA: 1000/166.13 = 6.019 kmol.
  2. p-Xylene = 6.019 × 106.17 = 639 kg.
  3. O₂ = 3 × 6.019 × 32 = 578 kg.

Answer: 0.639 t p-xylene and 0.578 t oxygen per tonne of PTA.

Feedstocks and cracking

Petrochemicals start from natural gas (methane, ethane) and refinery streams (naphtha, reformate). Steam cracking at about 800–850 °C with very short residence time breaks ethane or naphtha into ethylene, propylene and butadiene; catalytic reforming supplies benzene, toluene and xylenes (BTX).

  • Steam cracking → olefins
  • Reforming → aromatics (BTX)
  • Methane → syngas → methanol, ammonia

Example: Ethane is cracked: C₂H₆ → C₂H₄ + H₂. Find the maximum mass yield of ethylene.

  1. Ethane 30 g gives ethylene 28 g.
  2. 28/30 ≈ 93 %.

Answer: ≈ 93 %

Example: Which process supplies most benzene, toluene and xylenes?

  1. Dehydrogenation of naphthenes gives aromatics.
  2. Catalytic reforming (plus pyrolysis gasoline from crackers).

Answer: Catalytic reforming

Unit processes

Petrochemical routes are built from a few unit processes: cracking, reforming, hydrogenation (adds H₂), dehydrogenation (removes H₂), alkylation (adds an alkyl group), polymerisation, isomerisation, oxidation, chlorination, sulphonation and hydration.

  • Benzene + ethylene → ethylbenzene (alkylation)
  • Ethylbenzene → styrene (dehydrogenation)
  • Ethylene + water → ethanol (hydration)

Example: Name the unit processes: benzene + ethylene → ethylbenzene; ethylbenzene → styrene + H₂.

  1. Adding an ethyl group to the ring is alkylation.
  2. Removing hydrogen is dehydrogenation.

Answer: Alkylation; dehydrogenation

Products: monomers, detergents, insecticides

Ethylene → polyethylene, ethylene oxide and glycol, vinyl chloride (via ethylene dichloride) → PVC; propylene → polypropylene; butadiene → synthetic rubber; benzene → styrene, phenol, nylon intermediates. Synthetic detergents: linear alkylbenzene (LAB) is sulphonated to LAS, which is biodegradable, unlike the old branched ABS.

  • Ethylene → EDC → VCM → PVC
  • LAB → LAS (biodegradable)
  • Butadiene → synthetic rubber

Example: Outline how PVC is made from ethylene.

  1. Ethylene + Cl₂ → ethylene dichloride; cracking gives vinyl chloride + HCl.
  2. Vinyl chloride is polymerised to PVC.

Answer: C₂H₄ → EDC → VCM → PVC

Example: Why did detergents switch from branched ABS to linear LAS?

  1. Branched chains resist bacterial breakdown and caused foaming rivers.
  2. Linear chains biodegrade.

Answer: Biodegradability

Petrochemicals: first-generation building blocks (syngas, methanol, ammonia, ethylene, propylene, butadiene, BTX), intermediates (EO/MEG, VCM, styrene, cumene/phenol, acrylonitrile, caprolactam, PTA) and end products (polymers, fibres, rubbers, detergents). Syngas gives ammonia and methanol; steam cracking gives olefins; reformate gives BTX. Ethylene → PE, EO/MEG, PVC, styrene; propylene → PP, acrylonitrile, cumene/phenol; butadiene → rubbers; p-xylene + MEG → PET.

  • Steam cracking: 800–850 °C, steam dilution, < 1 s, quench.
  • LDPE: high pressure, free radical; HDPE/LLDPE: Ziegler–Natta.
  • Cumene process co-produces phenol and acetone.
  • Nylon 6 from caprolactam; nylon 6,6 from adipic acid + HMDA.

Key formulas

  • C₂H₄ + ½O₂ → C₂H₄O
  • C₆H₆ + C₃H₆ → cumene → phenol + acetone
  • C₈H₁₀ + 3O₂ → C₈H₆O₄ + 2H₂O
  • CO + 2H₂ → CH₃OH

Practice questions

The main feed for PET is PTA and

  1. propylene glycol
  2. mono-ethylene glycol
  3. methanol
  4. styrene
Show the answer

Answer: B. mono-ethylene glycol Polyester.

Phenol is made commercially mainly by the

  1. cumene process
  2. Claus process
  3. Fischer–Tropsch process
  4. Solvay process
Show the answer

Answer: A. cumene process Co-product acetone.

Acrylonitrile is made by

  1. ammoxidation of propylene
  2. chlorination of ethylene
  3. hydration of ethylene
  4. cracking of butane
Show the answer

Answer: A. ammoxidation of propylene SOHIO process.

LDPE is produced by

  1. Ziegler–Natta catalysis at low pressure
  2. free-radical polymerisation at high pressure
  3. condensation
  4. fermentation
Show the answer

Answer: B. free-radical polymerisation at high pressure 1000–3000 bar.

Caprolactam is the monomer of

  1. nylon 6
  2. PET
  3. PVC
  4. SBR
Show the answer

Answer: A. nylon 6 Ring-opening polymerisation.

Theory questions

Classify petrochemicals and give the main derivatives of ethylene and propylene. (6 marks)

Show the model answer

Classes: first-generation (basic building blocks: syngas, methanol, ammonia, ethylene, propylene, butadiene, benzene, toluene, xylenes), second-generation intermediates and end products. Ethylene: polyethylene (LDPE, LLDPE, HDPE), ethylene oxide → glycols, ethanolamines, surfactants; ethylene dichloride → vinyl chloride → PVC; ethylbenzene → styrene → polystyrene, SBR, ABS; ethanol; vinyl acetate; alpha-olefins. Propylene: polypropylene; acrylonitrile → acrylic fibre, ABS; propylene oxide → polyols, propylene glycol; cumene → phenol + acetone → bisphenol A, polycarbonate; isopropanol; oxo alcohols (butanol, 2-ethylhexanol); acrylic acid.

Describe steam cracking of naphtha for the production of olefins. (5 marks)

Show the model answer

Naphtha (or ethane/LPG) is mixed with steam (0.4–0.8 kg/kg) to lower hydrocarbon partial pressure and reduce coking, heated in convection coils and cracked in radiant tubes at 800–850 °C for 0.1–0.5 s. Products are quenched immediately in transfer-line exchangers (making high-pressure steam) and oil/water quench to stop secondary reactions. Gasoline and fuel oil are separated; cracked gas is compressed (4–5 stages), caustic-washed for CO₂/H₂S, dried and chilled; cryogenic fractionation separates methane/hydrogen, ethylene/ethane (C₂ splitter), propylene/propane (C₃ splitter), C₄s (butadiene extraction) and pyrolysis gasoline (aromatics). Acetylene is hydrogenated selectively. Furnaces are decoked periodically with steam–air.

Recent advances in refinery and petrochemical sectors

Topics: Indmax process, bio-refinery, ethanol production, future trends in petroleum refinery operations (taught by an oil & gas specialist).

Indmax, bio-refineries, ethanol and the refinery of the future

Indmax is an Indian Oil R&D technology: a high-severity fluid catalytic cracking process that converts heavy residues into light olefins (ethylene, propylene) and LPG together with high-octane gasoline, using a special catalyst formulation, higher riser temperature and higher catalyst-to-oil ratio than conventional FCC. The first Indmax unit was built at IOCL’s Guwahati refinery, and a large one runs at Paradip. Similar deep catalytic cracking ideas (DCC, petro-FCC) point the same way: making more petrochemicals per barrel of crude.

A bio-refinery processes biomass into fuels, chemicals and power, much as a refinery processes crude. First-generation ethanol is fermented from sugarcane juice, molasses or grain starch by yeast (C₆H₁₂O₆ → 2C₂H₅OH + 2CO₂), distilled to 95 % and dehydrated by molecular sieves to fuel-grade anhydrous ethanol. Second-generation (2G) ethanol comes from lignocellulosic residues such as rice straw (pre-treatment, enzymatic hydrolysis, fermentation), as at IOCL’s Panipat plant; Numaligarh is building a bamboo-based bio-refinery in Assam. India’s ethanol blending programme reached about 20 % blending in petrol (E20) around 2025. Other routes: biodiesel by transesterification of oils, compressed biogas, sustainable aviation fuel, and co-processing of bio-oils in hydrotreaters.

Future trends: higher conversion of residues (residue hydrocracking, gasification), crude-to-chemicals complexes, cleaner fuels (BS-VI and beyond), energy efficiency and digitalisation (advanced process control, real-time optimisation, digital twins), carbon capture, green hydrogen from electrolysis to replace grey hydrogen, and integration with renewable power as transport electrifies.

  • Indmax: residue → light olefins + LPG + gasoline (IOCL).
  • Fermentation: C₆H₁₂O₆ → 2C₂H₅OH + 2CO₂ (max 0.511 kg/kg).
  • 2G ethanol from straw and bamboo; E20 blending.
  • Green hydrogen, CCS and crude-to-chemicals.

Example: What is the theoretical ethanol yield from 1 tonne of glucose, and the real yield at 90 % of theoretical?

  1. C₆H₁₂O₆ (180.16) → 2C₂H₅OH (2 × 46.07 = 92.14) + 2CO₂.
  2. Theoretical = 92.14/180.16 = 0.511 t.
  3. At 90 %: 0.46 t ≈ 0.58 m³ (density 0.789).

Answer: 0.511 t theoretical, about 0.46 t (580 L) in practice.

Example: A state sells 1000 million litres of petrol a year. How much ethanol is needed for E20, and how much petrol is saved?

  1. E20 = 20 % ethanol by volume in the blend.
  2. Ethanol = 0.20 × 1000 = 200 million litres; petroleum petrol = 800 million litres.
  3. Ethanol has about two-thirds of petrol’s energy per litre, so slightly more blend volume is needed for the same distance.

Answer: 200 million litres of ethanol replaces 200 million litres of petrol (net saving a little less on an energy basis).

Indmax (IOCL) is a high-severity FCC that turns residue into light olefins, LPG and high-octane gasoline. Bio-refineries convert biomass into fuels and chemicals: 1G ethanol from sugar and starch, 2G ethanol from straw and bamboo (Panipat, Numaligarh), biodiesel, biogas, SAF; India reached about E20 blending. Future refineries: more residue conversion, crude-to-chemicals, cleaner fuels, digitalisation, carbon capture and green hydrogen.

  • Indmax favours propylene and LPG over gasoline.
  • Fuel ethanol must be anhydrous (molecular sieves break the azeotrope).
  • 2G ethanol uses non-food residues.
  • Green hydrogen replaces SMR hydrogen.

Key formulas

  • C₆H₁₂O₆ → 2C₂H₅OH + 2CO₂
  • Max ethanol = 0.511 kg/kg glucose
  • Triglyceride + 3CH₃OH → 3 methyl esters + glycerol

Practice questions

Indmax technology was developed by

  1. IOCL R&D
  2. UOP
  3. Shell
  4. Exxon
Show the answer

Answer: A. IOCL R&D Indian Oil.

The theoretical mass yield of ethanol from glucose is about

  1. 0.25
  2. 0.51
  3. 0.75
  4. 1.0
Show the answer

Answer: B. 0.51 92.14/180.16.

2G ethanol is produced from

  1. sugarcane juice
  2. grain starch
  3. lignocellulosic residues
  4. crude oil
Show the answer

Answer: C. lignocellulosic residues Straw, bamboo.

Fuel ethanol is dehydrated beyond the azeotrope using

  1. molecular sieves
  2. simple distillation
  3. filtration
  4. centrifugation
Show the answer

Answer: A. molecular sieves Adsorption of water.

Indmax mainly maximises

  1. bitumen
  2. light olefins and LPG
  3. lube oils
  4. coke
Show the answer

Answer: B. light olefins and LPG High severity.

Theory questions

Write a note on the Indmax process. (4 marks)

Show the model answer

Indmax is a residue fluid catalytic cracking technology from IOCL R&D designed to maximise light olefins and LPG. It uses a proprietary catalyst with high activity and metal tolerance, higher riser outlet temperature (≈ 550–600 °C), high catalyst-to-oil ratio (12–20) and short contact time, processing heavy feeds such as residue. Products: high yields of LPG (rich in propylene), ethylene in dry gas, and high-octane gasoline, with lower slurry. It enables petrochemical integration (polypropylene), as at the Paradip refinery; the first unit was at Guwahati.

What is a bio-refinery? Describe the production of fuel ethanol. (5 marks)

Show the model answer

A bio-refinery integrates conversion processes to produce fuels, power and chemicals from biomass, maximising value from each fraction. Fuel ethanol: (1G) sugarcane juice/molasses or grain starch (liquefied and saccharified by enzymes) is fermented by Saccharomyces yeast at 30–35 °C to 8–12 % ethanol; the beer is distilled to ≈ 95 % (azeotrope) and dehydrated in molecular-sieve beds to 99.5 %+; stillage is treated (biogas, fertiliser). (2G) lignocellulose (straw, bamboo) is pre-treated (steam explosion, dilute acid) to open the structure, cellulose and hemicellulose are hydrolysed by cellulases, sugars fermented, and lignin burnt for power. Ethanol is blended into petrol (E10–E20).

Notes, examples and questions were written for this studio; the prescribed books are listed in the studio for reference.

Frequently asked questions

What is the Petroleum Refining & Petrochemicals Studio?

Crude to petrol, polymers and beyond. Crude evaluation, API and Watson K, desalting, atmospheric and vacuum distillation, FCC, hydroprocessing, reforming, alkylation, Claus and MEROX, petrochemicals, Indmax and bio-refineries from the ASTU CHE241402 syllabus.

What can I do in the Petroleum Refining & Petrochemicals Studio?

Crude evaluation, API gravity and TBP cuts; Distillation, FCC, hydrotreating and reforming; Amine, Claus, MEROX, hydrogen and lube oils; Petrochemicals, Indmax and ethanol.

Is the Petroleum Refining & Petrochemicals Studio free?

Yes. It is free and runs in your browser with no sign-up.

Open the interactive studio →