IITIAN1997 STUDIO

Mass Transfer

Diffusion to distillation, step by step.

Open the interactive studio →

Diffusion, two-film theory, absorption (Kremser), drying, crystallisation, adsorption, leaching, extraction and distillation (flash, Rayleigh, McCabe–Thiele, Fenske–Underwood–Gilliland) from the ASTU MTO-I and MTO-II syllabi.

What is inside

  • Diffusion, mass-transfer theories and absorption
  • Drying, crystallisation and adsorption
  • Leaching, extraction and distillation
  • Calculators, MCQs, theory answers and videos

Syllabus: ASTU CHE241503 · CHE181602 Mass Transfer Operations I & II, semester 5 & 6, MTO-I NEP 2020; MTO-II 2018 scheme. Official syllabus PDF.

Molecular diffusion and mass-transfer coefficients

Topics: Basics of mass transfer; steady ordinary molecular diffusion and convective diffusion; diffusion in gases, liquids, biological solutions and gels, and solids; diffusion through constant and variable area; mass-transfer coefficients and their types; eddy diffusion.

Diffusion and vapour–liquid equilibrium

Fick’s law: the molar flux is proportional to the concentration gradient, N = −D dC/dz. Mass-transfer coefficients lump this into N = k ΔC across a film.

For ideal liquid mixtures Raoult’s law gives pᵢ = xᵢPᵢ°; the vapour is richer in the more volatile component. Relative volatility α = (y/x)_A / (y/x)_B = P_A°/P_B° for ideal systems; the larger α, the easier the separation. Azeotropes boil at constant composition and cannot be separated by ordinary distillation.

  • N = −D dC/dz
  • pᵢ = xᵢPᵢ° (Raoult); p = Hx (Henry)
  • α = P_A°/P_B°

Example: At 80 °C, P°(benzene) = 757 and P°(toluene) = 291 mmHg. For x_B = 0.5 find the total pressure and y_B.

  1. P = 0.5 × 757 + 0.5 × 291 = 524 mmHg.
  2. y_B = 378.5/524 = 0.722.

Answer: P = 524 mmHg, y_B ≈ 0.72

Example: Find the relative volatility of benzene to toluene at 80 °C.

  1. α = 757/291.
  2. ≈ 2.6.

Answer: ≈ 2.6

Fick’s law J_A = −D_AB dC_A/dz gives the diffusive flux relative to the mixture. For A diffusing through stagnant B (e.g. evaporation from a liquid surface) N_A = (D_AB P/RTz)·ln[(P − p_A2)/(P − p_A1)] = (D_AB P/RTz)(p_A1 − p_A2)/p_BM; for equimolar counter-diffusion N_A = D_AB(p_A1 − p_A2)/(RTz). Mass-transfer coefficients lump this: N_A = k_c ΔC = k_G Δp = k_y Δy. Gas diffusivities are ~10⁻⁵ m²/s, liquids ~10⁻⁹ m²/s.

  • Stagnant B gives a higher flux than equimolar counter-diffusion by the factor P/p_BM.
  • Diffusivity in gases ∝ T^1.75/P (Fuller); in liquids ∝ T/μ (Wilke–Chang).
  • k_G = k_c/RT; k_y = k_G P.
  • Eddy diffusion in turbulent flow is far faster than molecular diffusion.

Key formulas

  • J_A = −D_AB dC_A/dz
  • N_A = (D_AB P/RTz)(p_A1 − p_A2)/p_BM (A through stagnant B)
  • N_A = D_AB(p_A1 − p_A2)/(RTz) (equimolar)
  • p_BM = (p_B2 − p_B1)/ln(p_B2/p_B1)

Practice questions

Typical diffusivity of a gas at 1 atm is of the order of

  1. 10⁻⁵ m²/s
  2. 10⁻⁹ m²/s
  3. 10⁻¹ m²/s
  4. 10⁻¹² m²/s
Show the answer

Answer: A. 10⁻⁵ m²/s Gases diffuse fast.

For diffusion of A through stagnant B, the flux contains

  1. p_BM
  2. only Δp
  3. T⁴
  4. k_x
Show the answer

Answer: A. p_BM Log-mean of B.

Gas diffusivity varies with pressure as

  1. P
  2. 1/P
  3. P²
  4. independent
Show the answer

Answer: B. 1/P Halving pressure doubles D.

k_G and k_c are related by

  1. k_G = k_c RT
  2. k_G = k_c/RT
  3. k_G = k_c P
  4. k_G = k_c
Show the answer

Answer: B. k_G = k_c/RT C = p/RT.

Theory questions

Water evaporates from the bottom of a 0.1 m tube into dry air at 25 °C, 1 atm (p_vap = 3.17 kPa, D = 2.6 × 10⁻⁵ m²/s). Find the flux. (5 marks)

Show the model answer

p_A1 = 3.17 kPa at the surface, p_A2 = 0 at the top. N = (D P/(R T z)) ln[(P − p_A2)/(P − p_A1)] = (2.6 × 10⁻⁵ × 101 325/(8.314 × 298 × 0.1)) × ln(101.325/98.155) = 0.01063 × 0.0318 ≈ 3.4 × 10⁻⁴ mol/m²s.

Distinguish molecular and eddy diffusion. (3 marks)

Show the model answer

Molecular diffusion is due to random molecular motion and is slow; eddy (turbulent) diffusion is due to mixing by turbulent eddies, is many times faster and depends on flow, not just properties.

Diffusion equation and theories of mass transfer

Topics: Mass diffusion equation (equation of continuity); film theory, two-film theory, penetration theory, surface-renewal theory, boundary-layer theory.

The species continuity equation balances accumulation, convection, diffusion and reaction. Theories predict the mass-transfer coefficient: film theory k = D/δ (k ∝ D); Higbie’s penetration theory k = 2√(D/πt_c) (k ∝ D^0.5); Danckwerts’ surface renewal k = √(Ds) (k ∝ D^0.5); boundary-layer theory k ∝ D^(2/3). The two-film theory places two resistances in series at a gas–liquid interface with equilibrium at the interface.

  • Film: k ∝ D¹; penetration and surface renewal: k ∝ D^0.5; boundary layer: k ∝ D^(2/3).
  • Two-film: 1/K_y = 1/k_y + m/k_x.
  • Gas-film control when m is small (very soluble gas); liquid-film control when m is large.

Key formulas

  • k_film = D/δ
  • k_Higbie = 2√(D/(π t_c))
  • k_Danckwerts = √(D s)
  • 1/K_y = 1/k_y + m/k_x

Practice questions

According to film theory, k is proportional to

  1. D
  2. √D
  3. D^(2/3)
  4. D²
Show the answer

Answer: A. D k = D/δ.

Penetration theory was proposed by

  1. Lewis and Whitman
  2. Higbie
  3. Danckwerts
  4. Fick
Show the answer

Answer: B. Higbie 1935.

For a very soluble gas, the controlling resistance is in the

  1. gas film
  2. liquid film
  3. interface
  4. wall
Show the answer

Answer: A. gas film m small.

In surface-renewal theory k varies as

  1. D
  2. D^0.5
  3. D^(2/3)
  4. D^0
Show the answer

Answer: B. D^0.5 k = √(Ds).

Theory questions

Explain the two-film theory with a sketch and derive the overall coefficient. (5 marks)

Show the model answer

Two stagnant films on either side of the interface, equilibrium y_i = m x_i at the interface. N = k_y(y − y_i) = k_x(x_i − x). With y* = m x, y − y* = (y − y_i) + m(x_i − x) = N/k_y + mN/k_x, so 1/K_y = 1/k_y + m/k_x.

Compare film and penetration theories. (4 marks)

Show the model answer

Film theory: steady diffusion through a stagnant film, k ∝ D, film thickness unknown. Penetration theory: unsteady diffusion into fluid elements exposed for time t_c, k ∝ √D, closer to experiment for short contact.

Interphase mass transfer and gas absorption

Topics: Equilibrium between phases; mass transfer between two phases; interface concentration profiles; overall coefficients; material balance in contacting equipment; counter- and co-current operation; absorption, gas solubility, equilibrium and operating lines; batch and continuous stage-wise contactors; tower packings and their characteristics.

Absorption, extraction and drying

Gas absorption dissolves a component of a gas in a liquid (packed or tray towers); stripping is the reverse. Liquid–liquid extraction transfers a solute into a second solvent. Leaching extracts a solute from a solid.

Drying removes moisture: a constant-rate period (surface wet, like evaporation from water) is followed by a falling-rate period below the critical moisture content. Moisture on a dry basis X = water/dry solid; wet basis w = water/total.

  • Absorption: gas → liquid; stripping: liquid → gas
  • Dry basis X = water/dry solid
  • Constant rate, then falling rate

Example: 100 kg of wet solid with 40 % moisture (wet basis) is dried to 10 %. How much water is removed?

  1. Dry solid = 60 kg; final mass = 60/0.9 = 66.7 kg.
  2. Water removed = 100 − 66.7 = 33.3 kg.

Answer: 33.3 kg

Example: Express 40 % moisture (wet basis) on a dry basis.

  1. X = 40 kg water / 60 kg dry solid.
  2. = 0.667 kg/kg.

Answer: 0.667

In absorption a gas solute dissolves in a liquid. A balance on a counter-current tower gives the operating line Y₁ − Y₂ = (L_s/G_s)(X₁ − X₂) in solute-free ratios; it lies above the equilibrium line for absorption. Minimum liquid flow makes the operating line touch the equilibrium curve; actual flow is usually 1.2–1.5 times the minimum. Stage-wise towers are counted by stepping between lines (Kremser equation for dilute, linear systems); packed towers use height = HTU × NTU.

  • Operating line slope = L_s/G_s; equilibrium y = mx (Henry).
  • Absorption factor A = L/(mG); A > 1 makes good absorption possible.
  • Packing: Raschig rings, Pall rings, saddles, structured packing; wetting, pressure drop and flooding matter.
  • Z = HTU × NTU; NTU_OG ≈ ∫dy/(y − y*).

Key formulas

  • Y₁ − Y₂ = (L_s/G_s)(X₁ − X₂)
  • A = L/(mG)
  • Kremser: (y₁ − y₂)/(y₁ − mx₂) = (A^(N+1) − A)/(A^(N+1) − 1)
  • Z = H_OG × N_OG

Practice questions

For absorption, the operating line lies

  1. below the equilibrium line
  2. above the equilibrium line
  3. on it
  4. vertical
Show the answer

Answer: B. above the equilibrium line Solute moves gas → liquid.

At minimum liquid rate the number of stages is

  1. zero
  2. one
  3. infinite
  4. two
Show the answer

Answer: C. infinite Pinch.

The absorption factor is

  1. mG/L
  2. L/(mG)
  3. G/L
  4. m
Show the answer

Answer: B. L/(mG) A = L/mG.

Height of a packed tower equals

  1. HTU × NTU
  2. HTU/NTU
  3. NTU only
  4. HETP/NTU
Show the answer

Answer: A. HTU × NTU Z = H·N.

Theory questions

Explain minimum liquid-to-gas ratio in absorption with a sketch. (4 marks)

Show the model answer

As L_s/G_s falls, the operating line swings toward the equilibrium curve; when they touch (pinch), infinite stages are needed: that slope is the minimum. Practical designs use 1.2–1.5 × minimum.

Gas with 2 % solute is to be reduced to 0.1 % by pure solvent with m = 1 and A = 1.5. How many ideal stages (Kremser)? (5 marks)

Show the model answer

Fraction absorbed = (0.02 − 0.001)/0.02 = 0.95 = (A^(N+1) − A)/(A^(N+1) − 1). Solve: A^(N+1) = (0.95 − 1.5)/(0.95 − 1) = 11; (N + 1) ln 1.5 = ln 11 ⇒ N + 1 = 5.91 ⇒ N ≈ 4.9, so 5 stages.

Drying

Topics: Theory and mechanism; drying characteristics and rate curve; estimation of drying time; classification of driers; calculation of drying period; equations for various dryers; tray drying with varying air conditions; material and heat balances for continuous dryers.

A wet solid dries first at a constant rate (surface wet, rate set by heat and mass transfer from air) until the critical moisture X_c, then at a falling rate. Constant-rate time t_c = L_s(X₀ − X_c)/(A N_c); falling-rate time (linear) t_f = L_s(X_c − X*)/(A N_c)·ln[(X_c − X*)/(X − X*)]. Moisture is expressed on a dry basis X = kg water/kg dry solid. Dryers: tray, tunnel, rotary, drum, spray, fluidised bed, freeze.

  • Free moisture = X − X* (X* equilibrium moisture).
  • Constant rate N_c = h(T − T_w)/λ_w.
  • Spray dryers suit solutions (milk powder); rotary dryers suit granular solids.
  • Continuous dryer balances: L_s(X₁ − X₂) = G_s(Y₂ − Y₁).

Key formulas

  • X = water/dry solid
  • t_c = L_s(X₀ − X_c)/(A N_c)
  • t_f = [L_s(X_c − X*)/(A N_c)] ln[(X_c − X*)/(X − X*)]
  • N_c = h(T − T_w)/λ_w

Practice questions

During the constant-rate period the surface temperature is close to the

  1. dry-bulb temperature
  2. wet-bulb temperature
  3. dew point
  4. boiling point
Show the answer

Answer: B. wet-bulb temperature Surface behaves like a free water surface.

Moisture on a dry basis is

  1. water/total
  2. water/dry solid
  3. dry solid/water
  4. water/air
Show the answer

Answer: B. water/dry solid X.

Milk powder is made in a

  1. tray dryer
  2. spray dryer
  3. rotary kiln
  4. drum filter
Show the answer

Answer: B. spray dryer Atomised droplets.

Below the critical moisture content the rate

  1. stays constant
  2. falls
  3. rises
  4. is zero
Show the answer

Answer: B. falls Internal resistance controls.

Theory questions

100 kg (dry basis) of solid is dried from X = 0.4 to 0.1 on 2 m² with N_c = 1 kg/m²h, X_c = 0.2, X* = 0.02 (linear falling rate). Find the drying time. (5 marks)

Show the model answer

Constant: 100(0.4 − 0.2)/(2 × 1) = 10 h. Falling: 100(0.18)/(2 × 1) × ln(0.18/0.08) = 9 × 0.811 ≈ 7.3 h. Total ≈ 17.3 h.

Draw the drying rate curve and explain each period. (4 marks)

Show the model answer

Rate vs moisture: warm-up, constant-rate period (surface saturated, external control), critical moisture, falling-rate period (dry patches then internal diffusion control) down to equilibrium moisture.

Crystallisation

Topics: Theory; solid–liquid phase equilibrium; nucleation and crystal growth; solubility and material balance; batch crystallisation; continuous cooling crystallisers; DTB crystalliser; melt crystallisation.

Crystals form from supersaturated solutions: supersaturation drives nucleation (birth) and growth. A material balance with the solubility at the final temperature gives the yield; hydrates carry water of crystallisation, which must be counted. Cooling, evaporative and vacuum crystallisers, and the draft-tube-baffle (DTB) unit, control supersaturation and crystal size.

  • Supersaturation S = C/C* drives the process.
  • Primary (homogeneous/heterogeneous) and secondary nucleation.
  • ΔL law (McCabe): geometrically similar crystals grow at the same linear rate.
  • Hydrate yield: account for water of crystallisation using molar masses.

Key formulas

  • Solute balance: F x_F = C x_C + M x_M
  • Hydrate mass fraction of salt = M_salt/M_hydrate
  • S = C/C*

Practice questions

The driving force for crystallisation is

  1. undersaturation
  2. supersaturation
  3. temperature only
  4. pressure
Show the answer

Answer: B. supersaturation S > 1.

The ΔL law was proposed by

  1. McCabe
  2. Treybal
  3. Fick
  4. Nusselt
Show the answer

Answer: A. McCabe Equal linear growth.

DTB stands for

  1. double-tube boiler
  2. draft-tube baffle
  3. dry tray bed
  4. distillation tray bubble
Show the answer

Answer: B. draft-tube baffle A crystalliser type.

In a hydrate, the mass fraction of salt is

  1. M_salt/M_hydrate
  2. M_hydrate/M_salt
  3. 1
  4. M_water/M_salt
Show the answer

Answer: A. M_salt/M_hydrate CuSO₄ in CuSO₄·5H₂O is 159.6/249.7.

Theory questions

1000 kg of 30 % Na₂SO₄ solution is cooled; the mother liquor holds 15 % Na₂SO₄ and the crystals are Na₂SO₄·10H₂O (salt fraction 142/322). Find the crystal yield. (5 marks)

Show the model answer

Salt: 300 = 0.441C + 0.15(1000 − C) ⇒ 300 − 150 = (0.441 − 0.15)C ⇒ C ≈ 515 kg of decahydrate.

Explain nucleation and crystal growth. (3 marks)

Show the model answer

Nucleation creates new crystals (primary: from clear solution; secondary: from existing crystals). Growth adds solute to existing faces by diffusion and surface integration; both depend on supersaturation.

Adsorption, chromatography and ion exchange

Topics: Introduction to adsorption, chromatography and ion exchange.

Adsorption concentrates solutes on a solid surface. Equilibrium is described by isotherms: Langmuir q = q_m KC/(1 + KC) (monolayer) and Freundlich q = KC^(1/n). Fixed beds show a moving mass-transfer zone and a breakthrough curve. Chromatography separates by differing affinities for a stationary phase; ion exchange swaps ions between a resin and a solution (water softening, demineralisation).

  • Adsorbents: activated carbon, silica gel, alumina, zeolites.
  • Breakthrough time ends the useful bed life.
  • Langmuir assumes a monolayer of identical sites.
  • Cation resins in H⁺ form remove hardness; regeneration with acid.

Key formulas

  • Langmuir: q = q_m KC/(1 + KC)
  • Freundlich: q = K C^(1/n)
  • Bed capacity = mass × q

Practice questions

The Langmuir isotherm assumes

  1. multilayers
  2. a monolayer
  3. no saturation
  4. gas phase only
Show the answer

Answer: B. a monolayer Single layer.

Silica gel is used to adsorb

  1. water vapour
  2. oxygen
  3. nitrogen
  4. helium
Show the answer

Answer: A. water vapour A desiccant.

Water softening by resin is an example of

  1. adsorption
  2. ion exchange
  3. distillation
  4. drying
Show the answer

Answer: B. ion exchange Ca²⁺ exchanged.

The end of useful bed life is marked by

  1. regeneration
  2. breakthrough
  3. nucleation
  4. flooding
Show the answer

Answer: B. breakthrough Solute appears at the outlet.

Theory questions

Explain the breakthrough curve in fixed-bed adsorption. (4 marks)

Show the model answer

Outlet concentration vs time: zero while the mass-transfer zone moves through the bed, then rising (breakthrough) as the zone reaches the exit, to the feed value at exhaustion. A sharp curve means efficient use of the bed.

Compare Langmuir and Freundlich isotherms. (3 marks)

Show the model answer

Langmuir: theoretical, monolayer, approaches a maximum q_m. Freundlich: empirical power law, no maximum, fits heterogeneous surfaces over moderate ranges.

Solid–liquid extraction (leaching)

Topics: Classification; rate of leaching; contacting strategy and equipment; equilibrium; extraction calculations; supercritical extraction.

Leaching dissolves a soluble component from a solid with a solvent (sugar from beet, oil from seeds). Ideal stages assume the solution leaving with the solids has the same composition as the overflow. Counter-current multistage leaching uses solvent efficiently; Bollman and Rotocel extractors are common equipment. Supercritical CO₂ extracts caffeine and flavours without solvent residues.

  • Rate increases with smaller particles, higher temperature and agitation.
  • Underflow carries solution with the inert solids.
  • Counter-current gives the highest recovery for a given solvent.
  • Supercritical CO₂: above 31 °C and 73.8 bar.

Key formulas

  • Overflow and underflow balances per stage
  • Recovery = solute extracted/solute in feed

Practice questions

Extraction of oil from soybean is

  1. distillation
  2. leaching
  3. drying
  4. absorption
Show the answer

Answer: B. leaching Solid–liquid extraction.

Supercritical CO₂ is used to remove

  1. salt
  2. caffeine
  3. iron
  4. water
Show the answer

Answer: B. caffeine Decaffeination.

Leaching rate rises with

  1. larger particles
  2. smaller particles
  3. lower temperature
  4. no stirring
Show the answer

Answer: B. smaller particles More area, shorter path.

A Bollman extractor is used for

  1. gas absorption
  2. leaching
  3. distillation
  4. evaporation
Show the answer

Answer: B. leaching Moving-basket leaching.

Theory questions

State the factors affecting the rate of leaching. (4 marks)

Show the model answer

Particle size, solvent choice, temperature, agitation and the structure of the solid (diffusion through pores).

Why is counter-current contacting preferred in leaching? (3 marks)

Show the model answer

The freshest solvent meets the most exhausted solid, keeping a driving force throughout and giving higher recovery with less solvent.

Liquid–liquid extraction

Topics: Ternary liquid equilibria; solvent selection; single-stage, multistage and cross-current extraction; design calculations for stage-wise extraction.

A solvent partly immiscible with the feed carrier extracts solute; equilibrium is plotted on triangular diagrams with tie lines and the plait point. The distribution coefficient K = y/x and selectivity guide solvent choice. Cross-current extraction uses fresh solvent at every stage; counter-current extraction approaches the efficiency of distillation stages.

  • Solvent selection: high selectivity and capacity, low miscibility with carrier, easy recovery, cheap, safe.
  • Lever-arm rule gives phase amounts on the triangle.
  • Immiscible solvents: single stage fraction left = 1/(1 + E), with E = KS/F.

Key formulas

  • K = y/x
  • E = K·S/F (extraction factor)
  • Fraction unextracted (single stage) = 1/(1 + E)
  • n cross-current stages: 1/(1 + E/n)ⁿ (solvent split equally)

Practice questions

The point where the two liquid phases become identical is the

  1. plait point
  2. triple point
  3. dew point
  4. azeotrope
Show the answer

Answer: A. plait point Tie lines shrink to a point.

A good extraction solvent should have

  1. low selectivity
  2. high selectivity
  3. high miscibility with carrier
  4. high cost
Show the answer

Answer: B. high selectivity Selective for solute.

Splitting solvent across several cross-current stages

  1. extracts less
  2. extracts more
  3. has no effect
  4. is impossible
Show the answer

Answer: B. extracts more Better use of solvent.

Phase amounts on a triangular diagram follow the

  1. lever-arm rule
  2. Raoult law
  3. Fick law
  4. Kremser
Show the answer

Answer: A. lever-arm rule Mixing rule.

Theory questions

100 kg feed is extracted with 100 kg of immiscible solvent, K = 2 (mass ratio basis). Compare one stage with two cross-current stages of 50 kg each. (5 marks)

Show the model answer

One stage: E = 2, fraction left = 1/3 = 33 %. Two stages: E = 1 each, left = (1/2)² = 25 %. Splitting extracts more.

List the properties of a good solvent for extraction. (3 marks)

Show the model answer

Selectivity, high distribution coefficient, insolubility in the carrier, density difference for settling, easy recovery, low viscosity, chemical stability, low cost and toxicity.

Distillation

Topics: Vapour–liquid equilibrium, T–x–y diagram, bubble and dew points, relative volatility, non-ideality and azeotropes, enthalpy–concentration diagram; flash, steam, batch (Rayleigh) and continuous multistage distillation; batch distillation with reflux; minimum and total reflux; tray efficiency; reboilers; McCabe–Thiele and Ponchon–Savarit methods; packed columns.

Distillation and the McCabe–Thiele method

McCabe–Thiele assumes constant molar overflow. The rectifying operating line is y = [R/(R + 1)]x + x_D/(R + 1); the q-line through the feed point has slope q/(q − 1) (vertical for saturated liquid feed). Steps between the equilibrium curve and the operating lines count the theoretical stages.

Total reflux gives the minimum number of stages (Fenske): N_min = ln[(x_D/(1 − x_D))((1 − x_B)/x_B)]/ln α. Minimum reflux gives infinite stages; operating reflux is usually 1.2–1.5 times the minimum.

  • Rectifying line slope R/(R + 1), intercept x_D/(R + 1)
  • Saturated liquid feed: q = 1, vertical q-line
  • Fenske: minimum stages at total reflux

Example: With R = 2 and x_D = 0.9, find the slope and intercept of the rectifying line.

  1. Slope = 2/3 ≈ 0.667.
  2. Intercept = 0.9/3 = 0.3.

Answer: y = 0.667x + 0.3

Example: Find N_min for x_D = 0.95, x_B = 0.05 and α = 2.5.

  1. N_min = ln(19 × 19)/ln 2.5 = 5.889/0.916.
  2. ≈ 6.4 stages (including the reboiler).

Answer: ≈ 6.4

Distillation separates by relative volatility α. Flash distillation makes one equilibrium stage; batch differential distillation follows Rayleigh: ln(F/W) = ∫dx/(y* − x). Continuous columns are designed by McCabe–Thiele (constant molar overflow): rectifying line slope R/(R + 1), q-line slope q/(q − 1), steps between curve and lines give ideal stages; Fenske gives N_min at total reflux and Underwood the minimum reflux. Ponchon–Savarit uses enthalpy balances when molar overflow is not constant.

  • α = (y/x)_A/(y/x)_B; ideal: α = P_A°/P_B°.
  • Azeotropes cannot be crossed by ordinary distillation.
  • Optimum reflux ≈ 1.2–1.5 R_min.
  • Overall efficiency = ideal stages/actual stages.

Key formulas

  • y = αx/(1 + (α − 1)x)
  • y = [R/(R + 1)]x + x_D/(R + 1)
  • N_min = ln[(x_D/(1 − x_D))((1 − x_W)/x_W)]/ln α
  • ln(F/W) = ∫ dx/(y* − x)

Practice questions

At total reflux the number of stages is

  1. maximum
  2. minimum
  3. infinite
  4. zero
Show the answer

Answer: B. minimum Fenske.

For a saturated liquid feed the q-line is

  1. horizontal
  2. vertical
  3. at 45°
  4. absent
Show the answer

Answer: B. vertical q = 1.

Batch differential distillation is described by the

  1. Rayleigh equation
  2. Kremser equation
  3. Fenske equation
  4. Ergun equation
Show the answer

Answer: A. Rayleigh equation ln(F/W) = ∫…

Steam distillation is used for

  1. heat-sensitive, water-immiscible liquids
  2. azeotropes
  3. gases
  4. salts
Show the answer

Answer: A. heat-sensitive, water-immiscible liquids Boils below 100 °C.

Theory questions

With α = 2.5, x_D = 0.95 and x_W = 0.05, find N_min. (3 marks)

Show the model answer

N_min = ln(19 × 19)/ln 2.5 = 5.889/0.916 ≈ 6.4 stages (including the reboiler).

Explain the McCabe–Thiele method and its assumptions. (5 marks)

Show the model answer

Assumes constant molar overflow (equal latent heats, negligible heat effects), ideal stages. Draw the equilibrium curve, rectifying line through (x_D, x_D) with intercept x_D/(R + 1), q-line through (x_F, x_F), stripping line through (x_W, x_W); step from the top between curve and lines; the number of steps = ideal stages, the step crossing the q-line is the feed stage.

Notes, examples and questions were written for this studio; the prescribed books are listed in the studio for reference.

Frequently asked questions

What is the Mass Transfer Studio?

Diffusion to distillation, step by step. Diffusion, two-film theory, absorption (Kremser), drying, crystallisation, adsorption, leaching, extraction and distillation (flash, Rayleigh, McCabe–Thiele, Fenske–Underwood–Gilliland) from the ASTU MTO-I and MTO-II syllabi.

What can I do in the Mass Transfer Studio?

Diffusion, mass-transfer theories and absorption; Drying, crystallisation and adsorption; Leaching, extraction and distillation; Calculators, MCQs, theory answers and videos.

Is the Mass Transfer Studio free?

Yes. It is free and runs in your browser with no sign-up.

Open the interactive studio →