Mechanisms, drives, governors and machine elements
Topics: Links and kinematic pairs, mechanisms and inversions; belts and ropes; gears and gear trains; cams; flywheels and governors; balancing and vibration; keys, couplings, bearings, joints.
Links, pairs and mechanisms
A mechanism is a kinematic chain with one link fixed. Grübler’s criterion gives the degrees of freedom of a planar mechanism: F = 3(n − 1) − 2j − h (n links, j lower pairs, h higher pairs). A four-bar chain has F = 1. Grashof’s law: if s + l ≤ p + q, at least one link can rotate fully.
Inversions: the single slider-crank chain gives the IC engine, Whitworth and crank-and-slotted-lever quick-return mechanisms; the double slider gives the elliptical trammel and Oldham’s coupling.
- F = 3(n − 1) − 2j − h
- Four-bar: F = 1
- Grashof: s + l ≤ p + q
Example: Find the degrees of freedom of a four-bar chain (4 links, 4 turning pairs).
- F = 3(4 − 1) − 2 × 4.
- = 1.
Answer: 1
Example: Which mechanism is an inversion of the double slider-crank chain: the elliptical trammel or the Whitworth quick return?
- The trammel has two sliders in perpendicular grooves.
- The elliptical trammel.
Answer: Elliptical trammel
Belts and gear trains
A belt drive’s speed ratio N₂/N₁ = D₁/D₂ (ignoring slip); the tension ratio T₁/T₂ = e^(μθ) and power = (T₁ − T₂)v. Gears give positive drive: N₂/N₁ = T₁/T₂ (teeth). In a compound train, multiply the ratios of each pair; idlers change direction but not the speed ratio.
- Belt: N₂/N₁ = D₁/D₂
- T₁/T₂ = e^(μθ)
- Gears: N₂/N₁ = T₁/T₂, pair by pair
Example: A compound train has pairs 20/40 and 15/45 teeth. The input runs at 1200 rpm. Find the output speed.
- Ratio = (20/40) × (15/45) = 1/6.
- Output = 1200/6 = 200 rpm.
Answer: 200 rpm
Example: A belt has μ = 0.3 and lap angle 180°. Find T₁/T₂.
- T₁/T₂ = e^(0.3π).
- ≈ 2.57.
Answer: ≈ 2.57
Flywheels, governors and vibration
A flywheel stores energy to smooth speed within a cycle (fluctuation ΔE = Iω²C_s); a governor controls the mean speed against load changes. Watt governor height h ≈ 895/N² m (N in rpm); Porter and Hartnell governors are loaded for higher speeds.
Free vibration of a spring–mass system has natural frequency f = (1/2π)√(k/m); resonance occurs when the forcing frequency matches it, which is why rotating parts are balanced.
- Flywheel: within a cycle; governor: mean speed
- Watt: h = 895/N² m
- f_n = (1/2π)√(k/m)
Example: Find the height of a Watt governor running at 100 rpm.
- h = 895/100².
- ≈ 0.0895 m (about 90 mm).
Answer: ≈ 90 mm
Example: Find the natural frequency of a 10 kg mass on a 10 kN/m spring.
- ω = √(10 000/10) ≈ 31.6 rad/s.
- f = 31.6/(2π) ≈ 5.0 Hz.
Answer: ≈ 5 Hz
A kinematic chain with one link fixed is a mechanism, and fixing different links gives inversions. A four-bar chain has n = 4 and is the base of many mechanisms (Grashof’s law decides crank rotation). A single slider-crank gives the IC engine and a quick-return mechanism. Belts transmit by friction, with tension ratio T₁/T₂ = e^(μθ), and velocity ratio N₂/N₁ = D₁/D₂ neglecting slip. Gears give positive drive with velocity ratio inversely proportional to teeth. A flywheel smooths speed fluctuation within a cycle, and a governor regulates mean speed under changing load. Spur gears have straight teeth for parallel shafts, helical gears run quieter, and bevel gears join intersecting shafts.
- Lower pair: surface contact; higher pair: point or line contact.
- Worm gears give large reductions between non-intersecting shafts.
- Flywheel energy fluctuation ΔE = Iω²Cs.
- Governors: Watt, Porter, Proell (dead weight), Hartnell (spring).
- Module m = D/T; circular pitch = πm.
Key formulas
- T₁/T₂ = e^(μθ)
- N₂/N₁ = T₁/T₂ (teeth)
- m = D/T
- P = (T₁ − T₂)v
- ΔE = Iω²Cs
Practice questions
A flywheel controls speed variation
- over a long period under changing load
- within one cycle
- in only gas engines
- never
Show the answer
Answer: B. within one cycle Stores and releases energy.
A governor controls
- fluctuation in one cycle
- mean speed with load changes
- gear ratio
- belt tension
Show the answer
Answer: B. mean speed with load changes Adjusts fuel supply.
Sliding contact in a bearing or slider is a
- lower pair
- higher pair
- rolling pair
- free pair
Show the answer
Answer: A. lower pair Surface contact.
Gear and cam contact is a
- lower pair
- higher pair
- turning pair
- sliding pair
Show the answer
Answer: B. higher pair Line or point contact.
Intersecting shafts are joined by
- spur gears
- bevel gears
- helical gears only
- rack and pinion
Show the answer
Answer: B. bevel gears Conical teeth.
The tension ratio in a flat belt is
- e^(μθ)
- μθ
- θ/μ
- e^(θ)
Show the answer
Answer: A. e^(μθ) Tight/slack.
The Hartnell governor is
- spring-controlled
- dead-weight
- pendulum
- hydraulic
Show the answer
Answer: A. spring-controlled Spring-loaded.
A worm and worm wheel gives
- small speed reduction
- large speed reduction
- no reduction
- parallel-shaft drive
Show the answer
Answer: B. large speed reduction High ratio.
Module of a gear is
- T/D
- D/T
- πD/T
- T × D
Show the answer
Answer: B. D/T Pitch diameter/teeth.
Quick-return motion is used in
- shapers
- lathes only
- turbines
- boilers
Show the answer
Answer: A. shapers Slow cut, fast return.
The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.