IITIAN1997 STUDIO

Engineering materials

JLEE ME · 102 practice questions with answers

Practise and take a mock test →

Metals, alloys and heat treatment

Topics: Properties of materials; ferrous metals: iron–carbon diagram, steels and cast irons; non-ferrous alloys; heat treatment: annealing, normalising, hardening, tempering, surface hardening; testing of materials; plastics and composites.

Properties and testing

Mechanical properties: strength, hardness, toughness, ductility, brittleness, fatigue and creep resistance. The tensile test gives yield strength, ultimate tensile strength (P_max/A₀) and percentage elongation (ductility). Hardness tests: Brinell (ball), Rockwell (quick, depth), Vickers (diamond pyramid). Impact tests (Izod, Charpy) measure toughness.

  • UTS = P_max/A₀
  • % elongation = (L_f − L₀)/L₀ × 100
  • Brinell, Rockwell, Vickers

Example: A 10 mm bar breaks at 50 kN maximum load. Find the UTS.

  1. A₀ = π × 5² ≈ 78.5 mm².
  2. UTS = 50 000/78.5 ≈ 637 MPa.

Answer: ≈ 637 MPa

Example: A 50 mm gauge length stretches to 62 mm. Find the percentage elongation.

  1. (62 − 50)/50 × 100.
  2. = 24 %.

Answer: 24 %

Iron–carbon diagram

Steel contains up to about 2.1 % carbon, cast iron 2.1–6.67 %. At 727 °C austenite of 0.8 % C (eutectoid) turns into pearlite (ferrite + cementite). Hypo-eutectoid steels (< 0.8 % C) have ferrite plus pearlite; hyper-eutectoid steels have cementite plus pearlite. The lever rule gives the fraction of each phase.

Cast irons: grey (graphite flakes, good damping), white (hard, brittle), malleable and spheroidal-graphite (ductile).

  • Eutectoid 0.8 % C, 727 °C
  • Steel up to ≈ 2.1 % C
  • Lever rule for fractions

Example: A 0.4 % C steel is cooled slowly below 727 °C. Estimate the fraction of pearlite (ferrite holds 0.02 % C).

  1. Pearlite fraction = (0.4 − 0.02)/(0.8 − 0.02).
  2. ≈ 0.49 (about half).

Answer: ≈ 49 %

Heat treatment and alloys

Annealing (slow furnace cooling) softens and relieves stress; normalising (air cooling) refines grain; hardening (quenching from austenite) forms hard, brittle martensite; tempering reheats it to restore toughness. Surface hardening: carburising, nitriding, cyaniding, flame and induction hardening give a hard case on a tough core.

Non-ferrous alloys: brass (Cu + Zn), bronze (Cu + Sn), duralumin (Al + Cu + Mg + Mn), gun metal (Cu + Sn + Zn). Stainless steel contains at least about 10.5 % chromium.

  • Anneal: soften; normalise: refine grain
  • Harden by quench; temper for toughness
  • Brass Cu–Zn; bronze Cu–Sn

Example: Why is a hardened chisel tempered?

  1. Quenching leaves brittle martensite that could chip or shatter.
  2. Tempering trades a little hardness for toughness.

Answer: To restore toughness

Example: Which alloy is copper with tin?

  1. Brass is copper with zinc.
  2. Bronze.

Answer: Bronze

Steels contain up to about 2.1% carbon and cast irons beyond that. On the iron–carbon diagram the eutectoid is at 0.8% C, 723 °C (austenite → pearlite) and the eutectic at 4.3% C, 1147 °C. Annealing softens metal by slow furnace cooling, normalising refines grain by air cooling, hardening quenches to form martensite, and tempering reduces the resulting brittleness. Case hardening (carburising, nitriding) gives a hard surface and a tough core. Brass is copper with zinc, bronze copper with tin. Hardness is tested by Brinell, Rockwell and Vickers, and toughness by Izod and Charpy impact tests.

  • Cementite (Fe₃C) is hard and brittle; ferrite is soft.
  • Stainless steel has at least about 10.5% Cr, commonly 18-8 (Cr–Ni).
  • Duralumin is Al with Cu, Mg, Mn.
  • Malleable iron from white cast iron by annealing; grey iron has graphite flakes.
  • Ductility is ability to be drawn; malleability to be hammered into sheets.

Key formulas

  • Eutectoid: 0.8% C, 723 °C
  • Eutectic: 4.3% C, 1147 °C
  • BHN = 2P/[πD(D − √(D² − d²))]

Practice questions

Eutectoid carbon content of steel is about

  1. 0.08%
  2. 0.8%
  3. 2.1%
  4. 4.3%
Show the answer

Answer: B. 0.8% At 723 °C.

Martensite is formed by

  1. slow cooling
  2. quenching
  3. air cooling
  4. tempering
Show the answer

Answer: B. quenching Rapid cooling.

Tempering is done after

  1. annealing
  2. hardening
  3. casting
  4. forging only
Show the answer

Answer: B. hardening Reduces brittleness.

Brass is an alloy of copper and

  1. tin
  2. zinc
  3. lead
  4. aluminium
Show the answer

Answer: B. zinc Bronze has tin.

Bronze is an alloy of copper and

  1. tin
  2. zinc
  3. iron
  4. magnesium
Show the answer

Answer: A. tin Tin bronze.

Stainless steel owes its corrosion resistance mainly to

  1. carbon
  2. chromium
  3. lead
  4. sulphur
Show the answer

Answer: B. chromium Passive oxide film.

Impact strength is measured by

  1. the Izod test
  2. the Brinell test
  3. the Rockwell test
  4. the tensile test only
Show the answer

Answer: A. the Izod test Izod and Charpy.

Grey cast iron contains carbon as

  1. flakes of graphite
  2. cementite only
  3. spheres
  4. gas
Show the answer

Answer: A. flakes of graphite Flake graphite.

Normalising cools steel in

  1. the furnace
  2. still air
  3. water
  4. oil
Show the answer

Answer: B. still air Air cooling.

Nitriding produces

  1. a hard surface
  2. a soft surface
  3. a brittle core
  4. grey iron
Show the answer

Answer: A. a hard surface Surface hardening.

“Bog iron”, used to remove H₂S from coke-oven gas, is

  1. an intimate mixture of saw dust and iron dust (i.e. moist ferric hydroxide).
  2. iron impregnated with resin (usually bakelite).
  3. carbon free iron.
  4. none of these.
Show the answer

Answer: A. an intimate mixture of saw dust and iron dust (i.e. moist ferric hydroxide).

Iron containing up to about 2 % carbon is called

  1. pig iron
  2. wrought iron
  3. low carbon steel
  4. none of these
Show the answer

Answer: D. none of these

The softest mineral on Mohs’ scale is

  1. talc
  2. gypsum
  3. rubber
  4. none of these
Show the answer

Answer: A. talc

Karbate is

  1. a mixture of iron dust and saw dust.
  2. carbon impregnated with resin (usually bakelite).
  3. an acid resistant material.
  4. both (b) and (c).
Show the answer

Answer: D. both (b) and (c).

Duralumin is an alloy of

  1. aluminium, copper and manganese.
  2. aluminium, nickel and silicon.
  3. aluminium and nickel.
  4. none of these.
Show the answer

Answer: A. aluminium, copper and manganese.

The corrosion resistance of steel is improved by adding

  1. phosphorous and tungsten.
  2. nickel and chromium.
  3. lead and vanadium.
  4. molybdenum and tungsten.
Show the answer

Answer: B. nickel and chromium.

White metal is an alloy of

  1. lead, tin and cadmium
  2. copper, tin and zinc
  3. copper and lead
  4. none of these
Show the answer

Answer: A. lead, tin and cadmium

Adding cobalt to steel improves its

  1. cutting ability
  2. corrosion resistance
  3. tensile strength
  4. none of these
Show the answer

Answer: A. cutting ability

Pig iron tapped from a blast furnace contains about ____ % carbon.

  1. 0.2
  2. 2
  3. 4
  4. 8
Show the answer

Answer: C. 4

The carbon content of steel lies in the range of about ____ %.

  1. 0.1-2
  2. 4-6
  3. 2-4
  4. 0.001-0.01
Show the answer

Answer: A. 0.1-2

A very suitable material for storing 50 % caustic soda solution is

  1. karbate
  2. high silicon cast iron
  3. monel
  4. none of these
Show the answer

Answer: C. monel

A 15 % brine solution can be stored in a vessel of

  1. monel
  2. karbate
  3. cast iron
  4. none of these
Show the answer

Answer: A. monel

Concentrated nitric acid is best stored in

  1. cast iron
  2. monel
  3. karbate
  4. aluminium or chromium alloys (Cr >18% for cold acid)
Show the answer

Answer: D. aluminium or chromium alloys (Cr >18% for cold acid)

Babbitt metal for bearings consists mainly of

  1. mainly tin (85%) and lead.
  2. saw dust and iron dust mixture.
  3. zinc and aluminium.
  4. copper and aluminium.
Show the answer

Answer: A. mainly tin (85%) and lead.

The rollers of mills that squeeze juice from sugar cane are made of

  1. stainless steel
  2. cast iron
  3. mild steel
  4. monel
Show the answer

Answer: B. cast iron

The photochemical reactor for chlorinating benzene to BHC is lined with

  1. karbate
  2. lead or glass
  3. fireclay bricks
  4. PVC
Show the answer

Answer: B. lead or glass

The polymerisation reactor for SBR rubber is made of

  1. cast iron
  2. stainless steel or glass lined vessel
  3. karbate
  4. wrought iron
Show the answer

Answer: B. stainless steel or glass lined vessel

Evaporators and their tubes for concentrating NaOH to about 70 % are made of

  1. Cast iron
  2. Steel
  3. Nickel
  4. Karbate
Show the answer

Answer: C. Nickel

Type 316 stainless steel contains approximately

  1. 16–18 % Cr, 10–14 % Ni and 2–3 % Mo
  2. 20–22 % Cr and 8–10 % Ni
  3. 2–4 % Cr, 22 % Ni and 2–4 % Mo
  4. none of these
Show the answer

Answer: A. 16–18 % Cr, 10–14 % Ni and 2–3 % Mo

Caustic soda can be stored in ____ drums.

  1. steel
  2. cast iron
  3. brass
  4. gun metal
Show the answer

Answer: A. steel

Brass is an alloy of

  1. nickel and tin
  2. copper and zinc
  3. tin and lead
  4. copper, nickel and zinc
Show the answer

Answer: B. copper and zinc

The carbonating tower of the Solvay process is made of

  1. cast iron
  2. stainless steel
  3. karbate
  4. lead lined steel
Show the answer

Answer: A. cast iron

Gun metal is an alloy of

  1. nickel, tin and copper
  2. copper, tin and zinc
  3. copper, phosphorus and nickel
  4. manganese, phosphorus and nickel
Show the answer

Answer: B. copper, tin and zinc

The balls of a ball mill are usually made of

  1. steel
  2. cast iron
  3. stainless steel
  4. bronze
Show the answer

Answer: A. steel

Bronze is an alloy of copper with

  1. lead
  2. tin
  3. nickel
  4. zinc
Show the answer

Answer: B. tin

Rotary cement kilns are lined with

  1. fireclay
  2. silica
  3. lead
  4. high alumina & high magnesia
Show the answer

Answer: D. high alumina & high magnesia

In the kraft pulping process, the digester is commonly made of

  1. cast iron
  2. stainless steel
  3. karbate carbon
  4. wrought iron
Show the answer

Answer: A. cast iron

Dry chlorine can be handled in vessels of

  1. iron or steel
  2. PVC
  3. nickel
  4. brass
Show the answer

Answer: A. iron or steel

A glass-melting tank furnace is built of

  1. mild steel
  2. cast iron
  3. refractory blocks
  4. stainless steel
Show the answer

Answer: C. refractory blocks

Stainless steel contains

  1. chromium and nickel
  2. copper
  3. aluminium
  4. vanadium
Show the answer

Answer: A. chromium and nickel

In a mercury cell for caustic soda, the anode and cathode are respectively

  1. moving mercury and graphite.
  2. graphite and moving mercury.
  3. moving mercury and carbon.
  4. moving mercury and crimped steel wire.
Show the answer

Answer: B. graphite and moving mercury.

Monel metal is an alloy of

  1. molybdenum and nickel.
  2. nickel and copper.
  3. molybdenum and aluminium,
  4. molybdenum and zinc.
Show the answer

Answer: B. nickel and copper.

German silver is an alloy of

  1. copper, nickel and zinc.
  2. copper, aluminium and silver.
  3. silver, zinc and aluminium.
  4. silver, nickel and zinc.
Show the answer

Answer: A. copper, nickel and zinc.

Nichrome (chromel) is an alloy of

  1. chromium and molybdenum.
  2. nickel and chromium.
  3. molybdenum and nickel.
  4. chromium and aluminium.
Show the answer

Answer: B. nickel and chromium.

A material lacking toughness is called

  1. plastic
  2. malleable
  3. brittle
  4. ductile
Show the answer

Answer: C. brittle

Materials that break at small strains are brittle; those that deform considerably before breaking are

  1. rigid
  2. tough
  3. ductile
  4. plastic
Show the answer

Answer: C. ductile

Removing the scale formed on steel during hot rolling by acid treatment is called

  1. descaling
  2. shot blasting
  3. pickling
  4. skimming
Show the answer

Answer: C. pickling

Which joining method gives the weakest joint?

  1. soldering
  2. welding
  3. brazing
  4. rivetting
Show the answer

Answer: A. soldering

As the carbon content of steel rises, its

  1. yield stress decreases.
  2. elongation percent increases.
  3. tensile strength increases.
  4. impact strength increases.
Show the answer

Answer: C. tensile strength increases.

The tensile strength of common plastics lies roughly between ____ kg/mm².

  1. 10 to 50
  2. 50 to 100
  3. 0.01 to 0.1
  4. 0.1 to 10
Show the answer

Answer: D. 0.1 to 10

Which of these abrasives is synthetic?

  1. Corundum
  2. Emery
  3. Pumice
  4. Silicon caride
Show the answer

Answer: D. Silicon caride

Which of these is NOT ferromagnetic?

  1. Nickel
  2. Cobalt
  3. Aluminium
  4. Iron
Show the answer

Answer: C. Aluminium

Young’s modulus measures a material’s

  1. stiffness
  2. malleability
  3. creep resistance
  4. tensile strength
Show the answer

Answer: A. stiffness

Whether a material is ductile or brittle is best judged by the ____ test.

  1. Impact
  2. Cupping
  3. Hardness
  4. Tensile
Show the answer

Answer: A. Impact

For steel to respond to hardening treatment, its carbon content should be at least about ____ %.

  1. 0.2
  2. 0.4
  3. 0.6
  4. 0.8
Show the answer

Answer: A. 0.2

Photographic plates are coated with

  1. silver nitrate
  2. silver halide
  3. calcium silicats
  4. metallic silver
Show the answer

Answer: B. silver halide

Power-saw blades are made of

  1. Wrought iron
  2. Stainless steel
  3. Mild steel
  4. High speed steel
Show the answer

Answer: D. High speed steel

Which welding process reaches the highest temperature?

  1. Arc welding
  2. Gas welding
  3. Thermit welding
  4. Resistance welding
Show the answer

Answer: A. Arc welding

In brazing, metals are joined

  1. without melting the base metal.
  2. by melting the base metal.
  3. at temperatures above 450°C.
  4. none of these.
Show the answer

Answer: A. without melting the base metal.

A metal weighs 5 kg in air and 4 kg in water. Its specific gravity is

  1. 5
  2. 1.25
  3. 2.5
  4. 3.75
Show the answer

Answer: A. 5

The Rockwell number indicates

  1. hardness of a substance.
  2. colour of a pigment.
  3. density of a polymer.
  4. active ingredients in a fertiliser.
Show the answer

Answer: A. hardness of a substance.

Which metal reacts violently with water?

  1. Mercury
  2. Sodium
  3. Calcium
  4. Magnesium
Show the answer

Answer: B. Sodium

Lubrication is used to control

  1. friction
  2. wear
  3. temperature
  4. all (a), (b) & (c)
Show the answer

Answer: D. all (a), (b) & (c)

A material that expands freely on heating develops

  1. no
  2. compressive
  3. tensile
  4. thermal
Show the answer

Answer: A. no

The flux most used for brazing is

  1. zinc chloride
  2. borax
  3. ammonium chloride
  4. rosin
Show the answer

Answer: B. borax

Work-hardening steel for excavator buckets and bulldozer blades contains iron, carbon and

  1. manganese
  2. silicon
  3. nickel
  4. chromium
Show the answer

Answer: A. manganese

The cobalt–chromium–tungsten cast alloy used for cutting tools is

  1. Stellite
  2. High speed steel
  3. Cermet
  4. Alnico
Show the answer

Answer: A. Stellite

The most wear-resistant carbide for cutting tools is

  1. Aluminium carbide
  2. Tungsten carbide
  3. Nickel carbide
  4. Iron carbide
Show the answer

Answer: B. Tungsten carbide

Twist drills are usually made of

  1. cermets
  2. high speed steel
  3. alloy steel
  4. tungsten carbide
Show the answer

Answer: B. high speed steel

Adding which elements increases the hardness of carbon tool steel?

  1. vanadium & chromium
  2. silicon
  3. tungsten
  4. manganese
Show the answer

Answer: A. vanadium & chromium

Ceramic cutting-tool tips are made from

  1. carbon
  2. silicon carbide
  3. aluminium oxide
  4. tungsten
Show the answer

Answer: C. aluminium oxide

Electrochemical corrosion needs a ____ in contact with the metal.

  1. air
  2. oxygen
  3. liquid medium
  4. gaseous medium
Show the answer

Answer: C. liquid medium

Which lubricants have the least oiliness?

  1. Mineral oils
  2. Vegetable oils
  3. Greases
  4. Animal oils
Show the answer

Answer: A. Mineral oils

For a machine working at high temperature and load, the best lubricant is a

  1. grease
  2. solid lubricant
  3. animal oils
  4. mineral oils
Show the answer

Answer: B. solid lubricant

Automobile catalytic converters use a ____ catalyst.

  1. alumina
  2. platinum
  3. vanadium pentoxide
  4. iron oxide
Show the answer

Answer: B. platinum

The low-melting bismuth–lead alloy used for fuses is

  1. Wood's metal
  2. Babbit metal
  3. Monel metal
  4. Duralumin
Show the answer

Answer: A. Wood's metal

Holes for riveted joints are best made by

  1. drilling
  2. tapping
  3. reaming
  4. punching
Show the answer

Answer: A. drilling

For a riveted joint, if plate thickness is made four times larger, the rivet diameter should be made about ____ times larger.

  1. two
  2. four
  3. six
  4. eight
Show the answer

Answer: A. two

Iron loses its ferromagnetism at the Curie point, about ____ °C.

  1. 768
  2. 908
  3. 1400
  4. 1539
Show the answer

Answer: A. 768

Which material shows a distinct yield point?

  1. hard bronze
  2. soft brass
  3. cold rolled mild steel
  4. hot rolled mild steel
Show the answer

Answer: D. hot rolled mild steel

Steels commonly contain chromium up to about ____ %.

  1. 12
  2. 18
  3. 24
  4. 30
Show the answer

Answer: B. 18

The maximum permissible sulphur in steel is about ____ %.

  1. 0.015
  2. 0.055
  3. 0.505
  4. 0.805
Show the answer

Answer: B. 0.055

Which of these is the most malleable?

  1. Lead
  2. Copper
  3. Aluminium
  4. Wrought iron
Show the answer

Answer: A. Lead

Which element controls the properties of steel most?

  1. Manganese
  2. Silicon
  3. Carbon
  4. Vanadium
Show the answer

Answer: C. Carbon

Which addition increases the depth of hardening of steel?

  1. Chromium
  2. Nickel
  3. Tungsten
  4. Vanadium
Show the answer

Answer: A. Chromium

Fatigue resistance is measured by the

  1. elastic limit.
  2. ultimate tensile strength.
  3. Young's modulus.
  4. endurance limit.
Show the answer

Answer: D. endurance limit.

As impurities in a metal increase, its corrosion resistance

  1. increase
  2. decrease
  3. remain same
  4. may increase or decrease; depending on the type of metal
Show the answer

Answer: D. may increase or decrease; depending on the type of metal

Dezincification is corrosion of

  1. steel
  2. brass
  3. stainless steel
  4. babbit metal
Show the answer

Answer: B. brass

Cermets are usually about 80 % ceramic and 20 % metal. Which of these is a cermet?

  1. Zirconia
  2. Alumina
  3. Bakelite
  4. Tungsten carbide
Show the answer

Answer: D. Tungsten carbide

Foundry crucibles are made of

  1. lead
  2. stainless steel
  3. graphite
  4. cast iron
Show the answer

Answer: C. graphite

Dezincification mainly attacks

  1. brass
  2. nichrome
  3. stainless steel
  4. monel
Show the answer

Answer: A. brass

A fibrous fracture surface is typical of ____ materials.

  1. hard
  2. elastic
  3. ductile
  4. brittle
Show the answer

Answer: C. ductile

Which treatment does NOT protect a metal from corrosion?

  1. tempering
  2. chromising
  3. aluminising
  4. alloying
Show the answer

Answer: A. tempering

Silicon steel for electrical machines contains about ____ % silicon.

  1. 0.3-0.4
  2. 12-14
  3. 3-4
  4. 20-25
Show the answer

Answer: C. 3-4

Cold chisels and hammers are made of

  1. high speed steel
  2. high carbon steel
  3. forged steel
  4. mild steel
Show the answer

Answer: B. high carbon steel

Steel is heat-treated mainly to change its

  1. mechanical properties.
  2. physical properties.
  3. chemical composition.
  4. all a, b & c.
Show the answer

Answer: A. mechanical properties.

Coating steel with aluminium for resistance to oxidation up to about 700 °C is called

  1. Vaneering
  2. Galvanising
  3. Electroplating
  4. Calorising
Show the answer

Answer: D. Calorising

Cast iron water mains are usually joined by ____ joints.

  1. Collar
  2. Flanged
  3. Bell and Spigot
  4. Expansion
Show the answer

Answer: C. Bell and Spigot

Which of these is NOT a metalloid?

  1. Arsenic
  2. Antimony
  3. Lead
  4. none of these
Show the answer

Answer: C. Lead

The ultimate shear strength of steel is roughly ____ times its ultimate tensile strength.

  1. 0.5
  2. 0.75
  3. 1.5
  4. 2.5
Show the answer

Answer: B. 0.75

Which material has a negative coefficient of linear expansion when stretched?

  1. Iron
  2. Copper
  3. Rubber
  4. Nickel
Show the answer

Answer: C. Rubber

Factor of safety for ductile materials is the ratio of ____ stress to working stress.

  1. tensile
  2. compressive
  3. yield
  4. bearing
Show the answer

Answer: C. yield

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →