IITIAN1997 STUDIO

Non-conventional energy and mechatronics

JLEE ME · 10 practice questions with answers

Practise and take a mock test →

Solar, wind, biomass and power plants

Topics: Energy sources and need for renewables; solar thermal and photovoltaic; wind power; biomass and biogas; geothermal, tidal, small hydro; fuel cells; sensors, actuators and mechatronics basics; thermal, hydro, nuclear and diesel power plants.

Solar energy

Solar radiation at the ground peaks near 1000 W/m². Flat-plate collectors heat water; concentrating collectors reach higher temperatures. Photovoltaic cells convert light to electricity at about 15–22 % efficiency (silicon); output P = G × A × η, and daily energy ≈ rated power × peak sun hours.

  • P = G A η
  • Daily energy = P × peak sun hours
  • Flat plate: water heating

Example: A 1.6 m² panel at 20 % efficiency receives 1000 W/m². Find its output and daily energy for 5 peak sun hours.

  1. P = 1000 × 1.6 × 0.2 = 320 W.
  2. Energy = 320 × 5 = 1.6 kWh/day.

Answer: 320 W; 1.6 kWh

Wind, biomass and other renewables

Wind power P = ½ρAv³C_p: it grows with the cube of wind speed, and C_p cannot exceed the Betz limit of 59.3 %. Biomass is burnt, gasified or digested; biogas from anaerobic digestion is about 55–65 % methane. Geothermal, tidal and small hydro add to the mix; fuel cells turn hydrogen and oxygen directly into electricity.

  • P = ½ρAv³C_p
  • Betz limit 59.3 %
  • Biogas ≈ 60 % methane

Example: A 40 m rotor (C_p = 0.4) faces a 10 m/s wind (ρ = 1.225). Find the power.

  1. A = π × 20² ≈ 1257 m².
  2. P = 0.5 × 1.225 × 1257 × 1000 × 0.4 ≈ 308 kW.

Answer: ≈ 308 kW

Example: If wind speed doubles, how does wind power change?

  1. P ∝ v³.
  2. 2³ = 8 times.

Answer: 8 times

Power plants and mechatronics

Thermal plants follow the Rankine cycle (efficiency about 33–40 %; heat rate = 3600/η kJ/kWh); hydro plants convert P = ρgQHη; nuclear plants use fission heat; diesel plants suit standby and small loads.

Mechatronics combines mechanics, electronics and control: sensors (LVDT, strain gauge, thermocouple, proximity sensors) feed a controller (microcontroller or PLC) that drives actuators (motors, solenoids, hydraulic and pneumatic cylinders).

  • Heat rate = 3600/η kJ/kWh
  • Hydro: P = ρgQHη
  • Sensor → controller → actuator

Example: A thermal plant is 36 % efficient. Find its heat rate.

  1. Heat rate = 3600/0.36.
  2. = 10 000 kJ/kWh.

Answer: 10 000 kJ/kWh

Example: A hydro plant uses 10 m³/s under 50 m head at 90 % efficiency. Find the power.

  1. P = 1000 × 9.81 × 10 × 50 × 0.9.
  2. ≈ 4.4 MW.

Answer: ≈ 4.4 MW

Solar radiation can run collectors or photovoltaic cells; a silicon cell produces about 0.5–0.6 V, with panels formed from cells in series. Flat-plate collectors heat water to moderate temperatures, and concentrators reach higher ones. Wind turbine power is P = ½ρAV³C_p, with the Betz limit on C_p at 59.3%. Biogas from anaerobic digestion is mainly methane. A fuel cell converts chemical energy to electricity directly. In a nuclear reactor, moderators slow neutrons and control rods absorb them. Thermal plants use coal and the Rankine cycle; hydro plants use head and flow.

  • Solar constant ≈ 1367 W/m².
  • Biogas: about 55–65% methane.
  • Moderators: heavy water, graphite; control rods: cadmium, boron.
  • Tidal power uses barrages and range of tide.
  • Load factor = average load/maximum demand.

Key formulas

  • P = ½ρAV³C_p
  • C_p,max = 16/27
  • P_hydro = ρgQHη
  • Load factor = P_avg/P_max

Practice questions

Wind power varies with speed as

  1. V
  2. V²
  3. V³
  4. √V
Show the answer

Answer: C. V³ P ∝ V³.

The Betz limit is about

  1. 25%
  2. 59.3%
  3. 80%
  4. 100%
Show the answer

Answer: B. 59.3% 16/27.

Biogas mainly contains

  1. methane
  2. hydrogen
  3. oxygen
  4. nitrogen
Show the answer

Answer: A. methane Plus CO₂.

Photovoltaic cells convert sunlight into

  1. heat
  2. electricity
  3. wind
  4. fuel
Show the answer

Answer: B. electricity Direct conversion.

A moderator in a reactor

  1. absorbs all neutrons
  2. slows neutrons
  3. cools by evaporation
  4. makes fuel
Show the answer

Answer: B. slows neutrons Graphite, heavy water.

Control rods are made of materials such as

  1. cadmium
  2. copper
  3. aluminium
  4. iron
Show the answer

Answer: A. cadmium Neutron absorbers.

A fuel cell gives

  1. direct electricity
  2. mechanical work only
  3. steam
  4. wind
Show the answer

Answer: A. direct electricity Electrochemical.

Load factor is

  1. max/avg
  2. avg/max
  3. installed/avg
  4. avg × max
Show the answer

Answer: B. avg/max Definition.

Which is non-renewable?

  1. coal
  2. wind
  3. solar
  4. tidal
Show the answer

Answer: A. coal Fossil fuel.

Hydro plant power depends on

  1. head and discharge
  2. wind speed
  3. sunlight
  4. ash
Show the answer

Answer: A. head and discharge P = ρgQHη.

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →