IITIAN1997 STUDIO

Process control, valves, PLC and SCADA

JLEE IE · 11 practice questions with answers

Practise and take a mock test →

Controllers, final control elements and automation

Topics: Process variables and dynamics, dead time; on–off, P, PI, PD and PID control; tuning (Ziegler–Nichols); feedback, feed-forward, cascade and ratio control; control valves, characteristics, actuators, positioners, I/P converters; PLC architecture and ladder logic; DCS and SCADA; P&ID symbols.

Process dynamics and controller modes

Processes have capacity (giving first-order lags) and often dead time. On–off control is simple but cycles. Proportional control leaves an offset (for a unit set-point change with process gain K, offset = 1/(1 + K_cK)); integral action removes the offset but adds overshoot; derivative action anticipates and damps. Proportional band PB = 100/K_c %.

  • P: offset; I: removes offset; D: damps
  • PB = 100/K_c %
  • Offset = 1/(1 + K_c K)

Example: A controller has a proportional band of 25 %. Find K_c.

  1. K_c = 100/25.
  2. = 4.

Answer: 4

Example: With K_c = 4 and process gain 1, find the offset after a unit set-point change (P only).

  1. Offset = 1/(1 + 4 × 1).
  2. = 0.2 (20 %).

Answer: 0.2

Tuning and control strategies

Ziegler–Nichols (ultimate gain method): raise P gain until steady oscillation at K_u with period P_u; then PID: K_c = 0.6K_u, T_i = P_u/2, T_d = P_u/8. Strategies: feedback, feed-forward (acts on measured disturbances), cascade (a fast inner loop under a slow outer loop), ratio control (keeps two flows in proportion), split range and override.

  • Z–N PID: 0.6K_u, P_u/2, P_u/8
  • Cascade: inner loop faster
  • Ratio: B = r × A

Example: K_u = 8 and P_u = 10 s. Find the Ziegler–Nichols PID settings.

  1. K_c = 0.6 × 8 = 4.8.
  2. T_i = 10/2 = 5 s; T_d = 10/8 = 1.25 s.

Answer: K_c 4.8, T_i 5 s, T_d 1.25 s

Example: A ratio controller keeps B = 2 × A. Flow A is 50 L/min. What is B’s set point?

  1. B = 2 × 50.
  2. = 100 L/min.

Answer: 100 L/min

Final control elements and PLCs

Control valves have characteristics: linear, equal percentage (most common for process control) and quick opening (on–off). Air-to-open valves fail closed; air-to-close valves fail open: choose for safety. I/P converters turn 4–20 mA into 3–15 psi (0.2–1.0 bar) air; positioners ensure the stem goes where it is told. PLCs run ladder logic in a scan cycle (read inputs, run program, write outputs).

  • Air-to-open = fail closed
  • 4–20 mA → 3–15 psi
  • PLC scan: inputs, logic, outputs

Example: An I/P converter receives 12 mA. Find its output pressure (3–15 psi).

  1. 12 mA is half of the 4–20 mA span.
  2. 3 + 0.5 × 12 = 9 psi.

Answer: 9 psi

Example: A steam valve to a reactor must shut if air fails. Air-to-open or air-to-close?

  1. It must close when the air signal is lost.
  2. Air-to-open (fail closed).

Answer: Air-to-open

Proportional control leaves offset, integral removes it, and derivative anticipates rate of change. Proportional band = 100/K_c. On–off control is simple, but cycles about the set point. Cascade control uses a fast secondary loop inside a primary one; ratio control keeps two flows proportional; feed-forward acts on a measured disturbance. Control valves have quick-opening, linear or equal-percentage characteristics, and fail-safe action is air-to-open or air-to-close. An I/P converter turns 4–20 mA into 3–15 psi. A PLC scans inputs, runs a ladder program and writes outputs in a repeating cycle. SCADA supervises plants through RTUs and HMIs, and a DCS distributes control across controllers.

  • Ziegler–Nichols: P: K_c = 0.5K_u; PI: 0.45K_u, τᵢ = P_u/1.2; PID: 0.6K_u, τᵢ = P_u/2, τ_d = P_u/8.
  • Valve C_v: Q = C_v√(ΔP/SG).
  • Ladder: NO and NC contacts, coils, timers, counters.
  • P&ID tag FIC = flow indicating controller.
  • Air-to-open valves fail closed.

Key formulas

  • PB = 100/K_c
  • u = K_c(e + (1/τᵢ)∫e dt + τ_d de/dt)
  • Q = C_v√(ΔP/SG)

Practice questions

Offset is removed by

  1. proportional
  2. integral
  3. derivative
  4. on–off
Show the answer

Answer: B. integral Reset.

Derivative action responds to

  1. error magnitude
  2. rate of change of error
  3. time integral
  4. set point only
Show the answer

Answer: B. rate of change of error Anticipates.

Proportional band with K_c = 2 is

  1. 2%
  2. 20%
  3. 50%
  4. 200%
Show the answer

Answer: C. 50% 100/2.

A PLC’s scan begins with

  1. reading inputs
  2. printing
  3. tuning loops
  4. writing to SCADA only
Show the answer

Answer: A. reading inputs Input, program, output.

An air-to-open valve on air failure

  1. fails closed
  2. fails open
  3. stays half
  4. pumps
Show the answer

Answer: A. fails closed Spring closes.

An I/P converter gives

  1. pneumatic from current
  2. current from voltage
  3. digital from analogue
  4. power from air
Show the answer

Answer: A. pneumatic from current To the valve.

A loop inside another loop is

  1. cascade
  2. ratio
  3. on–off
  4. open-loop
Show the answer

Answer: A. cascade Secondary fast loop.

Feed-forward acts on

  1. a measured disturbance
  2. the offset
  3. the set point error
  4. noise only
Show the answer

Answer: A. a measured disturbance Before error appears.

In P&ID tags, TIC stands for

  1. temperature indicating controller
  2. total input current
  3. timer in control
  4. tank inlet check
Show the answer

Answer: A. temperature indicating controller ISA codes.

The relay logic-like PLC language is

  1. ladder diagram
  2. Java
  3. HTML
  4. SQL
Show the answer

Answer: A. ladder diagram IEC 61131.

For ratio control you keep

  1. two flows in proportion
  2. pressure zero
  3. time constant
  4. valve closed
Show the answer

Answer: A. two flows in proportion Blending.

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →