IITIAN1997 STUDIO

Industrial measurement: pressure, flow, level, temperature

JLEE IE · 11 practice questions with answers

Practise and take a mock test →

Measuring process variables

Topics: Pressure: manometers, Bourdon tube, bellows, diaphragm, McLeod and Pirani gauges; flow: orifice, venturi, rotameter, magnetic, turbine, ultrasonic, Coriolis; level: float, displacer, differential pressure, capacitance, ultrasonic; temperature: bimetal, RTD, thermistor, thermocouple, pyrometers; viscosity, humidity, density.

Pressure measurement

Units: 1 bar = 100 kPa ≈ 750 mmHg ≈ 10.2 m of water. Manometers and U-tubes for low pressures; Bourdon tubes, bellows and diaphragms for gauges; strain-gauge and capacitive transmitters for process work. Vacuum: McLeod gauge (reference), Pirani (thermal conductivity) and ionisation gauges for very low pressures. Absolute = gauge + atmospheric.

  • 1 bar ≈ 750 mmHg ≈ 10.2 m H₂O
  • Bourdon: gauge pressure
  • Pirani, McLeod: vacuum

Example: Express 1 bar in metres of water.

  1. h = p/ρg = 100 000/(1000 × 9.81).
  2. ≈ 10.2 m.

Answer: ≈ 10.2 m

Example: Which gauge measures vacuum by the cooling of a heated wire?

  1. Heat loss depends on gas pressure at low pressures.
  2. The Pirani gauge.

Answer: Pirani

Flow measurement

Head meters (orifice, venturi, flow nozzle, pitot) give Q ∝ √Δp. Variable-area rotameters read directly; magnetic flowmeters use Faraday’s law e = BDv (conductive liquids only); turbine meters give pulses proportional to volume; ultrasonic and vortex meters have no moving parts; Coriolis meters measure mass flow directly.

  • Q ∝ √Δp
  • Magnetic: e = B D v
  • Coriolis: mass flow

Example: A magnetic flowmeter has B = 0.1 T, pipe diameter 0.1 m and velocity 2 m/s. Find the EMF.

  1. e = BDv = 0.1 × 0.1 × 2.
  2. = 0.02 V = 20 mV.

Answer: 20 mV

Example: A turbine meter gives 100 pulses per litre. At 500 pulses per second, what is the flow?

  1. 500/100 = 5 L/s.
  2. = 300 L/min.

Answer: 5 L/s

Level and temperature measurement

Level: sight glass, float, displacer, DP (h = Δp/ρg), capacitance, ultrasonic and radar (distance from echo time, level = tank height − distance). Temperature: thermistors (narrow, sensitive), RTDs (about −200 to 850 °C, accurate), thermocouples (up to about 1800 °C), radiation pyrometers (non-contact, very hot bodies).

  • DP level: h = Δp/ρg
  • Ultrasonic: distance = v t/2
  • Pyrometer: no contact, high T

Example: A DP transmitter on a water tank reads 29.43 kPa. Find the level.

  1. h = 29 430/(1000 × 9.81).
  2. = 3 m.

Answer: 3 m

Example: An ultrasonic gauge on top of a 5 m tank hears its echo after 10 ms (sound 343 m/s). Find the level.

  1. Distance = 343 × 0.01/2 ≈ 1.715 m.
  2. Level = 5 − 1.715 ≈ 3.29 m.

Answer: ≈ 3.29 m

Elastic elements measure gauge pressure: Bourdon tubes (high), bellows (low to medium), diaphragms (low). McLeod and Pirani gauges read vacuum. Head flowmeters have Q ∝ √ΔP; a rotameter is variable-area; magnetic meters need conductive fluid, following Faraday’s law; Coriolis meters measure mass flow directly. Level uses p = ρgh in differential-pressure transmitters. RTDs (Pt100, 100 Ω at 0 °C, α ≈ 0.00385) are accurate and near linear; thermocouples follow the Seebeck effect, needing cold-junction compensation. Radiation pyrometers measure very high temperature without contact.

  • Thermocouples: K (chromel–alumel), J (iron–constantan), S/R (Pt–Rh).
  • Orifice has highest permanent loss; venturi the lowest of head meters.
  • Hygrometers measure humidity; psychrometers use wet and dry bulbs.
  • Redwood and Saybolt viscometers read efflux time.
  • Zero suppression and elevation adjust DP level transmitters.

Key formulas

  • Q ∝ √ΔP
  • R = R₀(1 + αΔT)
  • p = ρgh
  • Q = C_d A√(2gh)

Practice questions

An orifice flowmeter’s flow is proportional to

  1. ΔP
  2. √ΔP
  3. ΔP²
  4. 1/ΔP
Show the answer

Answer: B. √ΔP Head meter.

A magnetic flowmeter requires fluid that is

  1. conductive
  2. non-conductive
  3. gaseous
  4. cold only
Show the answer

Answer: A. conductive Faraday’s law.

Mass flow is measured directly by a

  1. Coriolis meter
  2. pitot tube
  3. rotameter
  4. weir
Show the answer

Answer: A. Coriolis meter Tube twist.

A Pt100 at 0 °C has resistance

  1. 0 Ω
  2. 10 Ω
  3. 100 Ω
  4. 1000 Ω
Show the answer

Answer: C. 100 Ω Name.

A thermocouple works on the

  1. Seebeck effect
  2. Hall effect
  3. Doppler effect
  4. Coriolis effect
Show the answer

Answer: A. Seebeck effect Thermo-EMF.

Type K thermocouple is

  1. chromel–alumel
  2. iron–constantan
  3. copper–constantan
  4. Pt–Rh
Show the answer

Answer: A. chromel–alumel General purpose.

Very high vacuum is measured by

  1. Bourdon tube
  2. McLeod gauge
  3. bellows
  4. U-tube only
Show the answer

Answer: B. McLeod gauge Compressed gas.

A rotameter is a

  1. variable-area meter
  2. head meter
  3. turbine meter
  4. magnetic meter
Show the answer

Answer: A. variable-area meter Float in taper tube.

Hot metal in furnaces is measured by a

  1. radiation pyrometer
  2. mercury thermometer
  3. RTD
  4. bimetal strip
Show the answer

Answer: A. radiation pyrometer Non-contact.

Liquid level by DP depends on

  1. ρgh
  2. flow speed
  3. colour
  4. viscosity only
Show the answer

Answer: A. ρgh Hydrostatic.

Bourdon tubes measure

  1. pressure
  2. temperature only
  3. flow only
  4. pH
Show the answer

Answer: A. pressure Elastic deformation.

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →