IITIAN1997 STUDIO

Electronic test and measurements

JLEE ECE / ETE · 10 practice questions with answers

Practise and take a mock test →

CRO, meters, generators and transducers

Topics: Errors and accuracy; analog and digital multimeters; CRO and DSO; signal generators; frequency counters; Q-meter, spectrum analyser, logic analyser; bridges; transducers and data acquisition.

Errors, accuracy and meters

Accuracy is closeness to the true value; precision is repeatability; resolution is the smallest detectable change. Errors are gross, systematic or random. A meter’s accuracy given as ±% of full scale gives a larger percentage error at low readings, so readings near full scale are better. A 3½-digit DMM reads up to 1999.

  • % error = (measured − true)/true × 100
  • ±% FSD hurts low readings
  • Accuracy vs precision vs resolution

Example: A voltmeter reads 102 V when the true value is 100 V. Find the % error.

  1. (102 − 100)/100 × 100.
  2. = 2 %.

Answer: 2 %

Example: A 0–100 V meter is ±1 % of full scale. What is the possible error at 20 V, as a % of reading?

  1. ±1 % of 100 V = ±1 V.
  2. ±1/20 = ±5 % of the reading.

Answer: ±5 %

Oscilloscopes and signal generators

A CRO or DSO plots voltage against time. Period = divisions × time/div; frequency = 1/period; peak-to-peak voltage = divisions × volts/div. Lissajous figures compare two frequencies: f_y/f_x = number of horizontal tangencies ÷ number of vertical tangencies. Function generators give sine, square and triangle waves; spectrum analysers show frequency content.

  • T = divisions × time/div
  • V_pp = divisions × volts/div
  • Lissajous ratio from tangencies

Example: One cycle spans 4 divisions at 0.5 ms/div. Find the frequency.

  1. T = 4 × 0.5 = 2 ms.
  2. f = 1/0.002 = 500 Hz.

Answer: 500 Hz

Example: A sine wave spans 3 divisions peak to peak at 2 V/div. Find its RMS value.

  1. V_pp = 6 V, so V_m = 3 V.
  2. V_rms = 3/√2 ≈ 2.12 V.

Answer: ≈ 2.1 V

Transducers and bridges

Transducers turn physical quantities into electrical signals: strain gauges (gauge factor GF = (ΔR/R)/ε), LVDTs for displacement, thermocouples, RTDs and thermistors for temperature, piezoelectric crystals for force and vibration, photodiodes for light. Bridges (Wheatstone, Maxwell, Schering) measure R, L and C; a Q-meter measures coil quality.

  • GF = (ΔR/R)/ε
  • LVDT: displacement
  • Type K ≈ 41 µV/°C

Example: A 120 Ω strain gauge changes by 0.24 Ω at strain 0.001. Find the gauge factor.

  1. ΔR/R = 0.002.
  2. GF = 0.002/0.001 = 2.

Answer: 2

Example: A type K thermocouple gives about 41 µV/°C. Estimate its output for a 100 °C difference.

  1. 41 × 100 µV.
  2. ≈ 4.1 mV.

Answer: ≈ 4.1 mV

Accuracy is closeness to the true value, precision is repeatability, and sensitivity of a voltmeter is the ohms-per-volt rating. A CRO deflects an electron beam by vertical and horizontal plates; a sawtooth time base gives the sweep; Lissajous figures compare frequency and phase. A DMM digitises input, commonly with a dual-slope integrating ADC. A function generator gives sine, square and triangle waves. A spectrum analyser shows amplitude against frequency, and a logic analyser shows many digital channels. A Q-meter uses series resonance to measure coil quality.

  • A voltmeter should have high input resistance to avoid loading.
  • CRO: electron gun, deflection plates, phosphor screen.
  • Frequency counters count pulses in a gate time.
  • Bridges: Wheatstone (R), Maxwell (L), Schering (C), Wien (f).
  • Peak-to-peak V_pp = 2√2 V_rms for a sine.

Key formulas

  • S = 1/I_fsd Ω/V
  • V_pp = 2√2 V_rms
  • f_y/f_x = horizontal/vertical tangencies

Practice questions

A CRO’s time base waveform is

  1. sine
  2. square
  3. sawtooth
  4. triangle always
Show the answer

Answer: C. sawtooth Linear sweep.

Lissajous patterns are used to find

  1. frequency and phase
  2. resistance
  3. current only
  4. power only
Show the answer

Answer: A. frequency and phase XY mode.

An ideal voltmeter has input resistance

  1. zero
  2. infinite
  3. 50 Ω
  4. 1 Ω
Show the answer

Answer: B. infinite No loading.

Dual-slope ADCs are valued for

  1. very high speed
  2. noise rejection
  3. large output
  4. no reference
Show the answer

Answer: B. noise rejection Integration averages.

A spectrum analyser displays

  1. amplitude vs frequency
  2. amplitude vs time
  3. current vs voltage
  4. phase only
Show the answer

Answer: A. amplitude vs frequency Frequency domain.

A Q-meter operates on

  1. series resonance
  2. rectification
  3. digital logic
  4. beat notes only
Show the answer

Answer: A. series resonance Voltage magnification.

Voltmeter sensitivity is expressed in

  1. Ω/V
  2. V/Ω
  3. A/V
  4. W/V
Show the answer

Answer: A. Ω/V ohms per volt.

Repeatability of readings is

  1. accuracy
  2. precision
  3. sensitivity
  4. range
Show the answer

Answer: B. precision Consistency.

A Wien bridge can measure

  1. frequency
  2. resistivity
  3. temperature only
  4. torque
Show the answer

Answer: A. frequency Also capacitance.

A logic analyser is used for

  1. many digital channels
  2. audio power
  3. high voltage
  4. insulation
Show the answer

Answer: A. many digital channels Timing and state.

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →