IITIAN1997 STUDIO

Engineering Graphics

JLEE and JMEE · 177 practice questions with answers

Practise and take a mock test →

Drawing basics: instruments, lines, lettering, dimensioning and scales

Topics: Drawing instruments and sheet sizes (BIS SP 46), types of lines and their uses, lettering, methods and rules of dimensioning, representative fraction, plain, diagonal and vernier scales.

Why engineers draw, and how a sheet is set out

A drawing tells a worker exactly what to make without a single spoken word. Two people who share no language can still build the same part from the same drawing, because the symbols and rules are standard. In India those rules come from the Bureau of Indian Standards, mainly SP 46.

Paper sizes are chosen so that each size is half of the one above it: A0 has an area of one square metre, A1 is half of that, and so on down to A4. Every sheet gets a border, which leaves a margin for filing, and a title block in the lower right corner. The title block holds the name, the drawing number, the scale, the date and the projection symbol, so anyone can identify the sheet at a glance.

  • A4: 210 × 297 mm
  • A3: 297 × 420 mm
  • A2: 420 × 594 mm
  • A1: 594 × 841 mm
  • A0: 841 × 1189 mm

Example: What is the ratio of the longer side to the shorter side of any A-size sheet, and why does it matter?

  1. Check A4: 297/210 = 1.414.
  2. Check A3: 420/297 = 1.414.
  3. This is √2. Halving a √2 sheet across its long side gives two sheets of the same shape.

Answer: The ratio is √2, so a drawing can be enlarged or reduced between sizes without changing its proportions.

Lines: each type has one meaning

A reader understands a drawing from its lines, so each kind of line must be used only for its proper purpose. The thick continuous line shows what you can actually see. A thin continuous line carries information about the object, such as dimensions and hatching. Short dashes show an edge hidden behind a surface, and a thin chain line marks a centre or an axis.

When lines coincide, an order of priority decides which one is drawn: a visible edge comes first, then a hidden edge, then a cutting plane, then a centre line, and last a dimension or extension line.

Example: A hole runs right through a block. In the front view, you cannot see the hole. How should it be drawn?

  1. The hole’s edges lie behind the front face, so they are hidden: use short dashes.
  2. The hole has an axis, so add one thin chain line along its centre.
  3. The outline of the block stays thick and continuous.

Answer: Two dashed lines for the hole’s edges with a chain centre line between them, inside a thick outline.

Lettering and dimensioning

Lettering is written in single-stroke capitals, in which each stroke has the thickness of the pen, because this is quick and easy to read. It may be vertical or inclined at 75° to the horizontal.

A dimension has three parts. Extension lines lead away from the object, leaving a small gap. A dimension line with arrowheads runs between them. A figure gives the size. Dimensions are in millimetres, and the unit is not written beside each number. In the aligned system, figures are read from the bottom or right side of the sheet; in the unidirectional system, all of them are read from the bottom.

  • Give each dimension once only.
  • Keep dimensions outside the views where you can.
  • Do not use an outline or a centre line as a dimension line.
  • Put smaller dimensions nearer the view so that lines do not cross.
  • Show a diameter with ⌀ and a radius with R.

Representative fraction and the plain scale

A bridge cannot fit on a sheet and a watch part is too small to draw at its true size, so a scale changes the size in a stated ratio. The representative fraction (R.F.) is the length on the drawing divided by the actual length, with both in the same unit. So it has no unit of its own. An R.F. below 1 reduces, and an R.F. above 1 enlarges.

A plain scale reads two units, such as metres and decimetres. Its length is R.F. × the longest length to be measured. Divide it into equal main parts, place zero at the end of the first part and number to the right, then divide the first part into the smaller unit. A length is read by taking main parts to the right of zero and small parts to the left.

Example: Construct a plain scale of R.F. = 1/50 to show metres and decimetres, long enough to measure 8 m. Show 5.6 m on it.

  1. Length of scale = 8 m × 1/50 = 800 cm/50 = 16 cm.
  2. Draw a 16 cm line and divide it into 8 equal parts: each part is 1 m.
  3. Mark 0 at the end of the first part, then 1, 2, 3 … to the right.
  4. Divide the first part into 10: each small part is 1 dm.
  5. For 5.6 m, take 5 main parts to the right of 0 and 6 small parts to the left.
  6. Write “R.F. = 1/50” and the units on the scale.

Answer: A scale 16 cm long. The length 5.6 m measures 5.6 × 2 = 11.2 cm on it.

The diagonal scale

A plain scale reads only two units. To read a third, a diagonal scale uses similar triangles. A small length, such as one tenth of a part, is divided into ten equal bits by drawing a sloping line across ten equal heights. Each step up the slope moves sideways by exactly one tenth of the small division.

Example: Construct a diagonal scale of R.F. = 1/4000 to read up to 500 m in metres. Show 438 m.

  1. Length of scale = 500 m/4000 = 50000 cm/4000 = 12.5 cm.
  2. Divide it into 5 equal parts: each is 100 m and 2.5 cm long.
  3. Divide the first part into 10: each is 10 m.
  4. Erect a perpendicular at the left end and mark 10 equal heights: each height stands for 1 m.
  5. Draw the diagonals across the first part.
  6. For 438 m, go up to height 8 (8 m), and measure from the 400 mark to the diagonal for 30 m.

Answer: A scale 12.5 cm long. On height line 8, 438 m runs from the 400 division to the third diagonal.

The vernier scale

A vernier reads a fine fraction of the main division with no diagonals. Usually, 10 vernier divisions cover the length of 9 main divisions. Each vernier division is therefore shorter by one tenth of a main division, which is the least count. To read one, note the main scale just before the vernier zero, then find which vernier line exactly matches a main line and add that number of least counts.

  • Least count = 1 MSD − 1 VSD = MSD/n, for a direct vernier.
  • The reading = main scale reading + vernier line × least count.
  • Vernier callipers commonly have a least count of 0.1 mm or 0.02 mm.

Example: In a vernier, 10 vernier divisions equal 9 main divisions, and 1 MSD = 1 mm. The main scale reads 24 mm, and the 7th vernier line coincides. Find the reading.

  1. 1 VSD = 9/10 = 0.9 mm.
  2. Least count = 1 − 0.9 = 0.1 mm.
  3. Reading = 24 + 7 × 0.1.

Answer: 24.7 mm

How JLEE asks it: lines, dimensioning and scales

Expect questions on line types (thick continuous for visible outlines, thin dashed for hidden edges, thin chain for centre lines), dimensioning rules (aligned and unidirectional systems, no dimension repeated) and the representative fraction.

RF = drawing length ÷ actual length in the same units. The length of a scale = RF × the maximum length to be measured.

  • RF = drawing size / actual size
  • Length of scale = RF × maximum length
  • Hidden edges: thin dashed lines

Example: 1 cm on a drawing represents 5 m. Find the RF.

  1. 5 m = 500 cm.
  2. RF = 1/500.

Answer: 1 : 500

Example: With RF 1/500, how long must a scale be to measure up to 50 m?

  1. 50 m = 5000 cm.
  2. Length = 5000/500 = 10 cm.

Answer: 10 cm

Drawings follow BIS SP 46. Sheet A0 is 1 m² (841 × 1189 mm) and each smaller size halves the previous (A4 = 210 × 297 mm). Continuous thick lines show visible outlines, thin dashed lines hidden edges, thin chain lines centre lines, thin continuous lines dimension and hatching lines, and thick chain lines cutting planes. Dimensions are given in millimetres, placed once, outside the view where possible, and read from the bottom or right (aligned) or from the bottom only (unidirectional). The representative fraction RF = drawing length/actual length; a diagonal scale reads three units (e.g. m, dm, cm) and a vernier scale uses the difference between main- and vernier-scale divisions.

  • RF > 1 is an enlarging scale, RF < 1 a reducing scale, RF = 1 full size.
  • Length of scale = RF × maximum length to be measured.
  • Least count of a vernier = 1 MSD − 1 VSD.
  • Single-stroke capital letters; height ratio of lower-case to capitals about 7 : 10.
  • Arrowhead length to width ratio about 3 : 1.

Key formulas

  • RF = drawing size / actual size
  • Scale length = RF × max length
  • LC = MSD − VSD

Practice questions

The size of an A4 sheet is

  1. 297 × 420 mm
  2. 210 × 297 mm
  3. 148 × 210 mm
  4. 420 × 594 mm
Show the answer

Answer: B. 210 × 297 mm Half of A3.

Hidden edges are shown by

  1. continuous thick lines
  2. thin dashed lines
  3. thin chain lines
  4. thick chain lines
Show the answer

Answer: B. thin dashed lines BIS convention.

Centre lines are drawn as

  1. thin chain lines
  2. thick continuous lines
  3. dashed lines
  4. zig-zag lines
Show the answer

Answer: A. thin chain lines Long-dash short-dash.

If 1 cm on a drawing represents 1 m, the RF is

  1. 1/10
  2. 1/100
  3. 1/1000
  4. 100
Show the answer

Answer: B. 1/100 1 cm/100 cm.

A scale with RF greater than 1 is

  1. reducing
  2. enlarging
  3. full size
  4. diagonal
Show the answer

Answer: B. enlarging Drawing larger than the object.

A diagonal scale can read

  1. one unit
  2. two units
  3. three units
  4. only fractions
Show the answer

Answer: C. three units For example m, dm and cm.

In the unidirectional system dimensions are read from

  1. the bottom only
  2. the right only
  3. bottom and right
  4. any side
Show the answer

Answer: A. the bottom only All horizontal text.

The area of an A0 sheet is

  1. 0.5 m²
  2. 1 m²
  3. 2 m²
  4. 0.25 m²
Show the answer

Answer: B. 1 m² 841 × 1189 mm.

Cutting-plane lines are

  1. thin continuous
  2. thin chain, thick at the ends and bends
  3. dashed
  4. freehand
Show the answer

Answer: B. thin chain, thick at the ends and bends BIS cutting-plane line.

The least count of a vernier with 10 VSD = 9 MSD of 1 mm is

  1. 0.1 mm
  2. 0.9 mm
  3. 1 mm
  4. 0.01 mm
Show the answer

Answer: A. 0.1 mm 1 − 0.9.

Engineering drawing is:

  1. Technical language of engineers for communicating design info
  2. Artistic drawing
  3. None
  4. Freehand sketch
Show the answer

Answer: A. Technical language of engineers for communicating design info

A dimension line ends with:

  1. Circles
  2. No terminator
  3. Squares
  4. Arrowheads at each end of measured extent
Show the answer

Answer: D. Arrowheads at each end of measured extent

Tolerance ±0.5 means:

  1. Acceptable range is nominal −0.5 to +0.5
  2. Exactly that value
  3. Random variation
  4. None
Show the answer

Answer: A. Acceptable range is nominal −0.5 to +0.5

Scale 2:1 on drawing means:

  1. Object drawn twice larger than actual
  2. Same size
  3. None
  4. Half size
Show the answer

Answer: A. Object drawn twice larger than actual

GD&T controls:

  1. Form, orientation, location and runout of features
  2. Only size
  3. Only finish
  4. None
Show the answer

Answer: A. Form, orientation, location and runout of features

Surface roughness Ra indicates:

  1. Average roughness in microns
  2. Colour
  3. Coating type
  4. None
Show the answer

Answer: A. Average roughness in microns

Parts list (BOM) in assembly drawing:

  1. Lists all components with part numbers, quantities, materials
  2. Shows only dimensions
  3. None
  4. Shows only weld details
Show the answer

Answer: A. Lists all components with part numbers, quantities, materials

A phantom line (double-short-dash) represents:

  1. Hidden lines
  2. None
  3. Alternate positions or adjacent parts not drawn
  4. Centre lines
Show the answer

Answer: C. Alternate positions or adjacent parts not drawn

Knurling symbol on drawing represents:

  1. Finish
  2. Textured surface pattern on cylindrical parts for grip
  3. Thread
  4. Weld
Show the answer

Answer: B. Textured surface pattern on cylindrical parts for grip

Thread notation M20×2.5 means:

  1. 20 inch diameter
  2. Metric thread, 20mm diameter, 2.5mm pitch
  3. None
  4. Random
Show the answer

Answer: B. Metric thread, 20mm diameter, 2.5mm pitch

Taper symbol on drawing indicates:

  1. None
  2. Gradual change in diameter over length
  3. Bend
  4. Step
Show the answer

Answer: B. Gradual change in diameter over length Gradual change in diameter over length (ratio shown)

Fillet weld symbol is:

  1. Right-angle triangle on reference line
  2. Square
  3. Circle
  4. Diamond
Show the answer

Answer: A. Right-angle triangle on reference line

Groove weld (butt weld) symbol:

  1. Circle
  2. Triangle
  3. None
  4. V-groove, U-groove, or bevel groove symbol on reference line
Show the answer

Answer: D. V-groove, U-groove, or bevel groove symbol on reference line

Spot weld symbol:

  1. Diamond
  2. Circle on reference line
  3. None
  4. Triangle
Show the answer

Answer: B. Circle on reference line

Surface finish symbol √ indicates:

  1. None
  2. Any process
  3. Material removal by machining required
  4. No machining
Show the answer

Answer: C. Material removal by machining required

Symbol with circle in √ means:

  1. Machining required
  2. No material removal
  3. Grinding required
  4. None
Show the answer

Answer: B. No material removal No material removal (surface as produced)

Limits and fits - clearance fit:

  1. Shaft larger than hole
  2. Shaft always smaller than hole
  3. None
  4. Shaft = hole
Show the answer

Answer: B. Shaft always smaller than hole Shaft always smaller than hole (positive clearance)

Interference fit:

  1. Clearance always
  2. None
  3. Shaft smaller
  4. Shaft larger than hole
Show the answer

Answer: D. Shaft larger than hole Shaft larger than hole (force fit needed for assembly)

Transition fit:

  1. Always clearance
  2. May be clearance or interference depending on actual sizes
  3. None
  4. Always interference
Show the answer

Answer: B. May be clearance or interference depending on actual sizes

ISO hole-basis system:

  1. Hole size fixed; shaft varied to achieve fit
  2. Both vary equally
  3. None
  4. Shaft fixed
Show the answer

Answer: A. Hole size fixed; shaft varied to achieve fit

Running dimensioning (chain) accumulates:

  1. None
  2. Reduces error
  3. No tolerances
  4. Tolerances
Show the answer

Answer: D. Tolerances Tolerances (avoid for precision; use datum dimensioning)

Datum dimensioning:

  1. All dimensions from single datum
  2. None
  3. Random
  4. Chain dimensioning
Show the answer

Answer: A. All dimensions from single datum All dimensions from single datum - tolerances don't accumulate

Micro symbol µ in drawing context:

  1. Micrometre; used for surface roughness Ra values
  2. Nano
  3. Milli
  4. None
Show the answer

Answer: A. Micrometre; used for surface roughness Ra values Micrometre (millionths of metre); used for surface roughness Ra values

Arrow type used for dimension lines:

  1. Circle
  2. Closed filled arrowhead
  3. Slash
  4. Open arrow
Show the answer

Answer: B. Closed filled arrowhead Closed filled arrowhead (most common in engineering)

Radius dimension labelled with:

  1. R before dimension
  2. Φ before
  3. None
  4. D before
Show the answer

Answer: A. R before dimension R before dimension (e.g. R25)

Diameter dimension labelled with:

  1. D only
  2. Φ before dimension
  3. None
  4. R before
Show the answer

Answer: B. Φ before dimension Φ (or Ø) before dimension

Countersink symbol:

  1. Circle
  2. U-shape
  3. None
  4. V-shaped symbol with angle specified
Show the answer

Answer: D. V-shaped symbol with angle specified

Cabinet drawing foreshortens depth to:

  1. Full length
  2. Half actual length
  3. Quarter
  4. None
Show the answer

Answer: B. Half actual length

Knurling symbol on drawing shows:

  1. Weld
  2. Thread
  3. Finish
  4. Raised diamond or straight pattern on cylindrical surface
Show the answer

Answer: D. Raised diamond or straight pattern on cylindrical surface

Symbol ⏥ in GD&T means:

  1. Circularity
  2. Cylindricity
  3. Flatness tolerance
  4. None
Show the answer

Answer: C. Flatness tolerance

Symbol ○ in GD&T means:

  1. Circularity
  2. None
  3. Cylindricity
  4. Straightness
Show the answer

Answer: A. Circularity Circularity (roundness)

Symbol ⌭ in GD&T means:

  1. Flatness
  2. Cylindricity
  3. None
  4. Circularity
Show the answer

Answer: B. Cylindricity

Symbol ∥ in GD&T means:

  1. Parallelism tolerance
  2. None
  3. Angularity
  4. Perpendicularity
Show the answer

Answer: A. Parallelism tolerance

Symbol ⊥ in GD&T means:

  1. Parallelism
  2. Angularity
  3. None
  4. Perpendicularity tolerance
Show the answer

Answer: D. Perpendicularity tolerance

True position tolerance:

  1. Form tolerance
  2. None
  3. Controls location of a feature relative to datum
  4. Size tolerance
Show the answer

Answer: C. Controls location of a feature relative to datum Controls location of a feature relative to datum - uses ⊕ symbol

Runout tolerance controls:

  1. None
  2. Form only
  3. Surface variation during rotation about datum axis
  4. Location only
Show the answer

Answer: C. Surface variation during rotation about datum axis

Profile of a surface tolerance:

  1. None
  2. Line only
  3. 3D tolerance zone surrounding true profile surface
  4. 2D only
Show the answer

Answer: C. 3D tolerance zone surrounding true profile surface

Maximum Material Condition (MMC):

  1. Minimum size
  2. Average size
  3. Feature at largest size
  4. None
Show the answer

Answer: C. Feature at largest size Feature at largest size - shaft at max diameter, hole at min diameter

Least Material Condition (LMC):

  1. Maximum size
  2. None
  3. Feature at smallest size
  4. Average size
Show the answer

Answer: C. Feature at smallest size Feature at smallest size - shaft at min diameter, hole at max diameter

Regardless of Feature Size (RFS):

  1. None
  2. Only at MMC
  3. Only at LMC
  4. Tolerance applies regardless of actual feature size
Show the answer

Answer: D. Tolerance applies regardless of actual feature size Tolerance applies regardless of actual feature size - default in ISO

Conical taper notation on drawing:

  1. Only ratio
  2. None
  3. 1:n format or angle
  4. Only angle
Show the answer

Answer: C. 1:n format or angle 1:n format (e.g. 1:10 means diameter changes 1mm per 10mm length) or angle

Slope notation on drawing:

  1. 1:n format for flat taper
  2. Angle only
  3. None
  4. Percentage only
Show the answer

Answer: A. 1:n format for flat taper 1:n format for flat taper (height changes 1 per n length)

Deep hole drilling symbol:

  1. None
  2. Φ
  3. Depth symbol ↧ with dimension value
  4. R
Show the answer

Answer: C. Depth symbol ↧ with dimension value

Counterbore symbol:

  1. Spotface
  2. Countersink
  3. None
  4. ⌴ with dimensions for diameter and depth
Show the answer

Answer: D. ⌴ with dimensions for diameter and depth

Countersink symbol:

  1. Spotface
  2. None
  3. Counterbore
  4. ⌵ with included angle and diameter
Show the answer

Answer: D. ⌵ with included angle and diameter

Spotface symbol:

  1. ⌴ with SF note
  2. Counterbore
  3. Countersink
  4. None
Show the answer

Answer: A. ⌴ with SF note ⌴ with SF note - shallow flat-bottomed recess for seating washer

Repetitive features notation:

  1. Text description only
  2. None
  3. Each drawn individually
  4. '4× Φ10' means four holes of 10mm diameter
Show the answer

Answer: D. '4× Φ10' means four holes of 10mm diameter

Symmetry symbol in older standards:

  1. None
  2. Flatness
  3. ⌯; replaced in newer ISO by general positional tolerance
  4. Location tolerance
Show the answer

Answer: C. ⌯; replaced in newer ISO by general positional tolerance ⌯ (symmetry about datum); replaced in newer ISO by general positional tolerance

Engineering drawing standard in India:

  1. BIS
  2. None
  3. ASME only
  4. ASTM only
Show the answer

Answer: A. BIS BIS (Bureau of Indian Standards) - SP-46, IS 696 etc.; also ISO standards adopted

Sheet sizes in engineering drawing:

  1. B series only
  2. Letter sizes only
  3. None
  4. A0 to A4; ISO A series
Show the answer

Answer: D. A0 to A4; ISO A series A0 (largest) to A4 (smallest); ISO A series - each half of previous

A0 sheet size:

  1. None
  2. 420 × 594 mm
  3. 594 × 841 mm
  4. 841 × 1189 mm
Show the answer

Answer: D. 841 × 1189 mm

A4 sheet size:

  1. 210 × 297 mm
  2. 297 × 420 mm
  3. 148 × 210 mm
  4. None
Show the answer

Answer: A. 210 × 297 mm

Revision table on drawing:

  1. Title block only
  2. None
  3. Contains revision letter, date, description, drawn/checked/approved columns
  4. Notes only
Show the answer

Answer: C. Contains revision letter, date, description, drawn/checked/approved columns

Zone system on drawing:

  1. Optional
  2. Alphanumeric grid on border to locate features
  3. None
  4. Only for large drawings
Show the answer

Answer: B. Alphanumeric grid on border to locate features Alphanumeric grid on border (A-D vertical, 1-8 horizontal) to locate features

Fold marks on drawing sheets:

  1. Sheet limits
  2. Indicate how to fold large sheets to A4 size for filing
  3. Revision marks
  4. None
Show the answer

Answer: B. Indicate how to fold large sheets to A4 size for filing

Material specification on drawing:

  1. Colour only
  2. e.g. IS 2062 Grade E250 for structural steel; ASTM A36 in USA
  3. None
  4. Trade name only
Show the answer

Answer: B. e.g. IS 2062 Grade E250 for structural steel; ASTM A36 in USA

Heat treatment notation on drawing:

  1. Weld symbol
  2. None
  3. e.g. 'Harden and temper to 55-60 HRC' in general notes
  4. Tolerance symbol
Show the answer

Answer: C. e.g. 'Harden and temper to 55-60 HRC' in general notes

Hardness on drawing specified as:

  1. Rockwell, Vickers, Brinell with range
  2. Only temperature
  3. Only process
  4. None
Show the answer

Answer: A. Rockwell, Vickers, Brinell with range Rockwell (HRC, HRB), Vickers (HV), Brinell (HB) with range

Electroplating specification on drawing:

  1. None
  2. e.g. 'Zinc plate 12µm per IS 1573' in notes
  3. Weld
  4. Material change
Show the answer

Answer: B. e.g. 'Zinc plate 12µm per IS 1573' in notes

Painting/coating specification:

  1. None
  2. Only colour
  3. Only thickness
  4. e.g. 'Prime coat + 2 finish coats, 75µm DFT, RAL 7035' in notes
Show the answer

Answer: D. e.g. 'Prime coat + 2 finish coats, 75µm DFT, RAL 7035' in notes

Casting drawing shows:

  1. Parting line, draft angle, machining allowance, shrinkage allowance
  2. None
  3. Only external shape
  4. Only material
Show the answer

Answer: A. Parting line, draft angle, machining allowance, shrinkage allowance

Forging drawing shows:

  1. None
  2. Flash line, die parting, draft angle, forging tolerances
  3. Only material
  4. Only dimensions
Show the answer

Answer: B. Flash line, die parting, draft angle, forging tolerances

Sheet metal drawing shows:

  1. Only material
  2. Only folded shape
  3. Developed blank with bend lines, bend radius, bend allowance
  4. None
Show the answer

Answer: C. Developed blank with bend lines, bend radius, bend allowance Developed (flat) blank with bend lines, bend radius, bend allowance

Bend allowance:

  1. Fillet weld size
  2. Extra material needed for bend
  3. Draft angle
  4. None
Show the answer

Answer: B. Extra material needed for bend Extra material needed for bend - function of bend radius, angle, material thickness

K-factor in sheet metal:

  1. None
  2. Hardness factor
  3. Safety factor
  4. Ratio describing neutral axis location in bend; typically 0.3-0.5
Show the answer

Answer: D. Ratio describing neutral axis location in bend; typically 0.3-0.5

Weld symbol on drawing - the arrow side:

  1. Weld made on the same side as the arrow
  2. None
  3. Both sides
  4. Opposite side
Show the answer

Answer: A. Weld made on the same side as the arrow

Weld symbol - other side (far side):

  1. Symbol placed above reference line
  2. Below reference line
  3. On arrow
  4. None
Show the answer

Answer: A. Symbol placed above reference line Symbol placed above reference line (no arrow directly)

All-around weld:

  1. Triangle
  2. None
  3. Circle at junction of arrow and reference line
  4. Square
Show the answer

Answer: C. Circle at junction of arrow and reference line

Weld all over symbol:

  1. No symbol
  2. 'All around' circle + flag for field weld if made on site
  3. None
  4. Dotted circle
Show the answer

Answer: B. 'All around' circle + flag for field weld if made on site

Coaxiality tolerance:

  1. Controls alignment of axis of feature with datum axis
  2. Parallelism
  3. None
  4. Straightness
Show the answer

Answer: A. Controls alignment of axis of feature with datum axis Controls alignment of axis of feature with datum axis - related to concentricity

Bonus tolerance in GD&T:

  1. No bonus
  2. Additional tolerance available when feature departs from MMC toward LMC
  3. Fixed tolerance only
  4. None
Show the answer

Answer: B. Additional tolerance available when feature departs from MMC toward LMC Additional tolerance available when feature departs from MMC toward LMC - (M) modifier

Free state variation:

  1. None
  2. Always constrained
  3. Flexible parts may need FT symbol to specify tolerance in free state
  4. No FT symbol
Show the answer

Answer: C. Flexible parts may need FT symbol to specify tolerance in free state Flexible parts may need FT symbol to specify tolerance in free (unclamped) state

Angularity tolerance:

  1. Perpendicularity only
  2. Controls angular surface or axis relative to datum
  3. None
  4. Parallelism only
Show the answer

Answer: B. Controls angular surface or axis relative to datum Controls angular surface or axis relative to datum - uses ∠ symbol

Pattern location tolerancing (composite):

  1. None
  2. Not applicable
  3. Single tier only
  4. Two-tier feature control frame
Show the answer

Answer: D. Two-tier feature control frame Two-tier feature control frame - upper FRTZF (pattern location), lower FRTZF (feature relationship)

Iso GPS standards (Geometrical Product Specifications):

  1. ASME Y14.5 only
  2. No international standard
  3. ISO 1101, ISO 5459, ISO 14253
  4. None
Show the answer

Answer: C. ISO 1101, ISO 5459, ISO 14253 ISO 1101, ISO 5459, ISO 14253 - international GD&T standards

ASME Y14.5-2018:

  1. ISO only
  2. 1994 standard
  3. USA GD&T standard
  4. None
Show the answer

Answer: C. USA GD&T standard USA GD&T standard - updated from 2009 version; clarifies composite tolerances, adds new concepts

Surface texture measurement - cut-off wavelength λc:

  1. None
  2. Only Ra measured
  3. Separates roughness from waviness
  4. No separation
Show the answer

Answer: C. Separates roughness from waviness Separates roughness from waviness - typically 0.8 mm for most engineering surfaces

Waviness (W) vs roughness (R):

  1. Waviness
  2. None
  3. No distinction
  4. Same parameter
Show the answer

Answer: A. Waviness Waviness: longer wavelength form errors; Roughness: short wavelength surface texture - different significance

Rz vs Ra surface roughness:

  1. Rz = average of 5 peak-to-valley heights; Ra = average roughness
  2. Ra = Rz
  3. Same parameter
  4. None
Show the answer

Answer: A. Rz = average of 5 peak-to-valley heights; Ra = average roughness Rz = average of 5 peak-to-valley heights; Ra = average roughness - Rz more sensitive to peaks

Engineering drawings for 3D printing (AM):

  1. Include layer direction, support structures, surface finish note, and material specification
  2. None
  3. No special notes
  4. Same as casting
Show the answer

Answer: A. Include layer direction, support structures, surface finish note, and material specification

Build orientation in AM drawings:

  1. Not important
  2. Critical for mechanical properties, surface finish, and support requirements
  3. None
  4. Random
Show the answer

Answer: B. Critical for mechanical properties, surface finish, and support requirements Critical for mechanical properties, surface finish, and support requirements - noted on drawing

DXF/DWG file formats:

  1. DXF = AutoCAD interchange format; DWG = native AutoCAD format
  2. PDF only
  3. None
  4. Image only
Show the answer

Answer: A. DXF = AutoCAD interchange format; DWG = native AutoCAD format DXF = AutoCAD interchange format; DWG = native AutoCAD format - widely used in industry

STEP (AP203/AP214) file format:

  1. DXF only
  2. Standard for Exchange of Product Data
  3. PDF only
  4. None
Show the answer

Answer: B. Standard for Exchange of Product Data Standard for Exchange of Product Data - 3D CAD neutral format for interoperability

Revision triangle symbol on drawing:

  1. None
  2. No location marking
  3. Filled triangle with revision letter
  4. Cloud only
Show the answer

Answer: C. Filled triangle with revision letter Filled triangle with revision letter - marks location of change on drawing

Drawing transmittal record:

  1. Email only
  2. Formal list of drawings sent to client/vendor
  3. No record needed
  4. None
Show the answer

Answer: B. Formal list of drawings sent to client/vendor Formal list of drawings sent to client/vendor - document control procedure

Superseded drawing status:

  1. Previous revision replaced but retained for reference
  2. None
  3. Voided completely
  4. Active still
Show the answer

Answer: A. Previous revision replaced but retained for reference Previous revision replaced but retained for reference - marked SUPERSEDED on title block

Void drawing status:

  1. None
  2. Superseded
  3. Drawing cancelled
  4. Active drawing
Show the answer

Answer: C. Drawing cancelled Drawing cancelled - never built or erroneously issued - marked VOID

Engineering change notice (ECN):

  1. None
  2. No documentation
  3. Informal memo
  4. Formal document authorising and documenting change to engineering drawing or design
Show the answer

Answer: D. Formal document authorising and documenting change to engineering drawing or design

DCR (Drawing Change Request):

  1. ECN already approved
  2. Formal request proposing change before it is approved and implemented
  3. No formal process
  4. None
Show the answer

Answer: B. Formal request proposing change before it is approved and implemented

Interchangeability in drawings:

  1. Tolerances set so any manufactured part fits mating part
  2. No tolerances
  3. None
  4. Custom fit only
Show the answer

Answer: A. Tolerances set so any manufactured part fits mating part Tolerances set so any manufactured part fits mating part - basis of mass production

Go/No-Go gauges:

  1. Verify that features are within tolerance limits
  2. Measure exact size
  3. None
  4. No verification
Show the answer

Answer: A. Verify that features are within tolerance limits Verify that features are within tolerance limits - Go gauge fits easily; No-Go does not fit

CMM (Coordinate Measuring Machine):

  1. Manual measurement
  2. Automated 3D measurement of manufactured parts against CAD model
  3. 2D only
  4. None
Show the answer

Answer: B. Automated 3D measurement of manufactured parts against CAD model Automated 3D measurement of manufactured parts against CAD model - GD&T verification

First article inspection (FAI):

  1. None
  2. No inspection
  3. Complete inspection of first production part to verify it meets drawing requirements before production run
  4. Only final inspection
Show the answer

Answer: C. Complete inspection of first production part to verify it meets drawing requirements before production run

STEP AP242 standard:

  1. "
  2. L
  3. a
  4. [
Show the answer

Answer: D. [

PLM (Product Lifecycle Management):

  1. [
  2. S
  3. o
  4. "
Show the answer

Answer: A. [

Model-Based Definition (MBD):

  1. A
  2. l
  3. [
  4. "
Show the answer

Answer: C. [

Digital twin in engineering:

  1. [
  2. "
  3. V
  4. i
Show the answer

Answer: A. [

Augmented Reality (AR) for drawings:

  1. "
  2. [
  3. O
  4. v
Show the answer

Answer: B. [

Geometric tolerancing - straightness of axis:

  1. Controls how straight the axis of a cylinder must be
  2. None
  3. Surface straightness only
  4. Not applicable to axis
Show the answer

Answer: A. Controls how straight the axis of a cylinder must be Controls how straight the axis of a cylinder must be - uses ⏤ symbol

Positional tolerance for a hole pattern:

  1. Only size tolerance
  2. Controls location and orientation of holes relative to datum
  3. None
  4. Only roundness
Show the answer

Answer: B. Controls location and orientation of holes relative to datum Controls location and orientation of holes relative to datum - most commonly used GD&T call-out

Geometrical constructions and engineering curves

Topics: Bisecting lines and angles, regular polygons, conic sections by eccentricity and other methods, cycloid, epicycloid, hypocycloid, involute and spirals.

Conics by the eccentricity method

A conic is the path of a point P that moves so that its distance from a fixed point (the focus, F) divided by its distance from a fixed line (the directrix) stays constant. This constant is the eccentricity, e. If e is below 1 the curve is an ellipse, if e = 1 a parabola, and if e is above 1 a hyperbola. The same construction draws all three.

First place the vertex V on the axis, dividing the distance from directrix to focus so that VF/VD = e. Then a sloping line from the directrix’s foot through a point above V gives, at any position along the axis, a height equal to e times the distance from the directrix. Use that height as a radius from F, and cut the vertical line at that position. Each pair of cuts gives two points on the curve.

Example: Draw an ellipse with the focus 50 mm from the directrix and e = 2/3. Find the position of the vertex and describe the construction.

  1. VF/VD = 2/3, and VF + VD = 50 mm.
  2. So VF = 50 × 2/5 = 20 mm and VD = 30 mm.
  3. At V, erect VE = VF = 20 mm and join D to E, extending the line. Its height at any point is 2/3 of the distance from the directrix.
  4. Mark points 1, 2, 3 … along the axis beyond V and draw verticals.
  5. With F as centre and each vertical’s height up to the sloping line as radius, cut that vertical above and below the axis.
  6. Join the points with a smooth curve.

Answer: The vertex lies 30 mm from the directrix and 20 mm from the focus.

Example: Show how to draw the tangent and normal at a point P on this conic.

  1. Join P to the focus F.
  2. At F, draw a line at 90° to PF, meeting the directrix at T.
  3. Join T to P: this is the tangent.
  4. Through P, draw a line at 90° to the tangent: this is the normal.

Answer: Tangent PT, with the normal perpendicular to it at P.

Cycloid and involute

Roll a circle along a straight line without slipping and watch one point on its rim: its path is a cycloid. In one full turn, the circle travels a distance equal to its circumference, πD, and the point rises to a height D. To draw it, divide the circle and the length πD into 12 equal parts. As the centre moves to each position, the point stands at the matching height, found by striking an arc from the new centre.

If the circle rolls on the outside of another circle the curve is an epicycloid, and on the inside it is a hypocycloid. An involute is the path of the end of a taut string unwound from a circle. Gear teeth are shaped this way because such teeth transmit motion smoothly.

  • Cycloid: base length πD, height D.
  • Involute of a circle: unwound string length after one turn = πD.
  • Epicycloid: rolls outside. Hypocycloid: rolls inside.

Example: A circle of 50 mm diameter rolls along a line. Find the base length and height of the cycloid and give the first steps of drawing it.

  1. Base length = πD = π × 50 ≈ 157 mm.
  2. Height = D = 50 mm.
  3. Draw the circle with its point P at the bottom, and a 157 mm base.
  4. Divide the circle and the base into 12 equal parts.
  5. Draw horizontals through the divisions of the circle, and find the centres C1 to C12 along the line through its centre.
  6. With centre C1 and radius 25 mm, cut horizontal 1: this is P1. Repeat for all the rest and join the points smoothly.

Answer: A curve 157 mm long and 50 mm high.

Conic sections from a cone

Cutting a right circular cone at different angles shows why these curves are called conic sections. Compare the angle between the cutting plane and the axis with the half-angle at the apex. A plane perpendicular to the axis gives a circle. A larger angle than the half-angle gives an ellipse. An equal angle, meaning the plane is parallel to a generator, gives a parabola. A smaller angle gives a hyperbola.

How JLEE asks it: engineering curves

The eccentricity e = distance from the focus ÷ distance from the directrix decides the conic: e < 1 ellipse, e = 1 parabola, e > 1 hyperbola. A cycloid is traced by a point on a circle rolling along a line; one full revolution covers a base length of πD. An involute is traced by the end of a string unwound from a circle.

  • e < 1 ellipse; e = 1 parabola; e > 1 hyperbola
  • cycloid base = πD for one revolution
  • involute: unwinding a taut string

Example: A circle of 50 mm diameter rolls without slipping for one revolution. How long is the base of the cycloid?

  1. Base length = circumference = πD.
  2. π × 50 ≈ 157.1 mm.

Answer: ≈ 157.1 mm

Example: A point moves so its distance from a fixed point is 2/3 of its distance from a fixed line. Name the curve.

  1. e = 2/3.
  2. e < 1, so the curve is an ellipse.

Answer: Ellipse

A conic is the path of a point whose distance from a fixed point (focus) bears a constant ratio e to its distance from a fixed line (directrix): e < 1 ellipse, e = 1 parabola, e > 1 hyperbola. Cutting a cone parallel to the base gives a circle, inclined to the base a closed ellipse, parallel to a generator a parabola, and parallel to the axis a hyperbola. A cycloid is traced by a point on a circle rolling on a straight line; epicycloid when it rolls outside another circle, hypocycloid inside. An involute is traced by the end of a string unwound from a circle or polygon and is the profile of gear teeth.

  • Length of a cycloid base = πD (one revolution).
  • Archimedean spiral: radius increases uniformly with angle (cams).
  • Ellipse methods: concentric circles, rectangle, oblong, arcs of circles, eccentricity.
  • Rectangular hyperbola: asymptotes at right angles (PV = constant).
  • Involute of a circle is used for gear teeth.

Key formulas

  • e = distance from focus / distance from directrix
  • Cycloid base = πD

Practice questions

A parabola has eccentricity

  1. < 1
  2. = 1
  3. > 1
  4. 0
Show the answer

Answer: B. = 1 Definition.

The curve traced by a point on a circle rolling on a straight line is a

  1. cycloid
  2. involute
  3. spiral
  4. helix
Show the answer

Answer: A. cycloid Cycloid.

Gear teeth profiles are usually

  1. cycloids
  2. involutes
  3. parabolas
  4. ellipses
Show the answer

Answer: B. involutes Involute profile.

A section of a cone parallel to a generator is a

  1. circle
  2. ellipse
  3. parabola
  4. hyperbola
Show the answer

Answer: C. parabola Parabola.

The base length of a cycloid for one revolution of a 50 mm circle is

  1. 50 mm
  2. 100 mm
  3. 157 mm
  4. 314 mm
Show the answer

Answer: C. 157 mm π × 50.

A point rolling inside a circle traces a

  1. hypocycloid
  2. epicycloid
  3. cycloid
  4. involute
Show the answer

Answer: A. hypocycloid Inside → hypo.

Cam profiles commonly use the

  1. Archimedean spiral
  2. hyperbola
  3. cycloid
  4. ellipse
Show the answer

Answer: A. Archimedean spiral Uniform rise.

The curve PV = constant is a

  1. parabola
  2. rectangular hyperbola
  3. ellipse
  4. straight line
Show the answer

Answer: B. rectangular hyperbola Boyle’s law curve.

Profile of a line tolerance:

  1. None
  2. Flat surface
  3. 3D profile
  4. 2D tolerance zone along a curve relative to true profile
Show the answer

Answer: D. 2D tolerance zone along a curve relative to true profile

IFC file format:

  1. Industry Foundation Classes
  2. Mechanical only
  3. None
  4. Piping only
Show the answer

Answer: A. Industry Foundation Classes Industry Foundation Classes - BIM (Building Information Modelling) standard for construction

Orthographic projection of points, lines, planes and solids

Topics: Principal planes, first and third angle projection, projections of points and lines (true length and inclinations), traces, projections of planes, projections of prisms, pyramids, cylinders and cones in simple positions.

The idea of first-angle projection

Imagine an object between you and a transparent plane. Parallel rays from its corners, perpendicular to the plane, mark its outline on the plane. A vertical plane (VP) gives the front view, and a horizontal plane (HP) gives the top view. The two planes meet along the reference line XY. To put both views on flat paper, the HP is swung down about XY.

In first-angle projection, which BIS recommends, the object is above the HP and in front of the VP. After the HP swings down, the top view lies below the front view. In third-angle projection, the planes lie between you and the object, so the top view lies above the front view.

Example: In first-angle projection, where is the view from the left placed on the sheet?

  1. In first angle, each view is drawn on the far side of the object from where you look.
  2. Looking from the left, the view appears on the right of the front view.

Answer: To the right of the front view

Example: A 30 mm cube rests on the HP with one face parallel to the VP and 10 mm in front of it. Describe its front and top views in first-angle projection.

  1. Front view: a 30 mm square standing on XY, since the cube rests on the HP.
  2. Top view: a 30 mm square below XY, its edge nearest XY drawn 10 mm below it, because that face is 10 mm in front of the VP.

Answer: A square on XY above, and a square starting 10 mm below XY

Projections of points

A point is fixed by its distance from each plane. The front view a′ is drawn at the point’s height above or below XY, and the top view a at its distance in front of or behind the VP. Both lie on one projector, perpendicular to XY. Height decides where a′ goes, and distance from the VP decides where a goes.

  • First quadrant: a′ above XY, a below XY.
  • Second quadrant: both above XY.
  • Third quadrant: a′ below XY, a above XY.
  • Fourth quadrant: both below XY.

Example: A point P is 20 mm below HP and 30 mm behind VP. State its quadrant and describe its views.

  1. Below HP and behind VP means the third quadrant.
  2. The front view shows the height: p′ is 20 mm below XY.
  3. The top view shows the distance from VP: behind VP places p 30 mm above XY.
  4. Both lie on one projector.

Answer: Third quadrant, with p′ 20 mm below XY and p 30 mm above XY.

Projections of lines

A line parallel to a plane shows its true length (TL) on that plane. A line perpendicular to a plane shows as a point on that plane. A line inclined to a plane is foreshortened on it, and a line inclined to both planes is foreshortened in both views, with apparent angles larger than the true ones.

To draw a line inclined to both planes, first draw it as if it were parallel to the VP, at its true angle θ: its base gives the plan length, and its top gives the height of b′. Then do the same with the other angle to get the elevation length and the distance of b from the VP. Finally, swing each length to meet its locus line.

Example: A line AB, 80 mm long, has A 15 mm above HP and 20 mm in front of VP. It is inclined at 30° to HP and 45° to VP. Find the lengths and the positions of b′ and b.

  1. Plan length = 80 cos 30° = 69.3 mm.
  2. Elevation length = 80 cos 45° = 56.6 mm.
  3. Height of b′ above HP = 15 + 80 sin 30° = 55 mm.
  4. Distance of b from VP = 20 + 80 sin 45° = 76.6 mm.
  5. Horizontal distance between the projectors = √(69.3² − 56.6²) = √(4802 − 3204) ≈ 40 mm.
  6. Mark b′ on the 55 mm line and b on the 76.6 mm line, 40 mm along from A.

Answer: Top view 69.3 mm, front view 56.6 mm, with end projectors 40 mm apart.

Projections of planes and solids

A plane parallel to the HP shows its true shape in the top view and appears as a line in the front view. A plane inclined to the HP shows as a line at its inclination in the front view, and is foreshortened in the top view.

Solids are drawn in stages. In stage 1, the solid rests in the simplest position, with its axis perpendicular to a plane, so that the view on that plane shows the true shape of the base. In stage 2, the front view from stage 1 is redrawn tilted. Every corner’s distance from XY in the top view stays unchanged, so each new top-view point is found by projecting down from the tilted view and across from the first top view.

  • Prism and cylinder: two equal bases joined by side faces.
  • Pyramid and cone: one base and an apex.
  • A hidden edge lies behind a visible surface: draw it dashed.

How JLEE asks it: orthographic projection

In first-angle projection (used in India, BIS SP 46) the object sits between the observer and the plane, so the top view (plan) is drawn below the front view (elevation). In third angle the plan is above.

A line inclined at θ to the HP shows its true length in the elevation when parallel to the VP; its plan is shortened to L cos θ and its height difference is L sin θ.

  • First angle: plan below elevation
  • Plan length = L cos θ (θ to HP)
  • Height difference = L sin θ

Example: An 80 mm line is parallel to the VP and inclined at 30° to the HP. Find its plan length and the difference in height of its ends.

  1. Plan = 80 cos 30° ≈ 69.3 mm.
  2. Height difference = 80 sin 30° = 40 mm.

Answer: Plan ≈ 69.3 mm; rise 40 mm

Example: In first-angle projection, where is the left side view placed?

  1. The object is viewed from the left and projected onto the plane behind it.
  2. The left view is drawn on the right of the front view.

Answer: To the right of the front view

Orthographic projection uses parallel projectors perpendicular to the plane. In first-angle projection (used in India, BIS) the object is between the observer and the plane, so the top view is drawn below the front view and the left view on the right; in third-angle the plane is between observer and object and the top view is above. A line parallel to a plane shows its true length on that plane; when inclined to both, its true length is found by rotation or an auxiliary view. A solid resting on its base in the HP has its true-shape base in the top view and its height in the front view.

  • Symbol of first-angle projection: truncated cone with the circle view on the right.
  • A point in the 1st quadrant is above HP and in front of VP: FV above XY, TV below XY.
  • A line perpendicular to HP appears as a point in the top view.
  • Traces: HT is where the line meets HP, VT where it meets VP.
  • A plane perpendicular to both HP and VP is a profile plane.

Key formulas

  • TL² = (ΔX)² + (ΔY)² + (ΔZ)²
  • Plan length = TL cos θ (θ to HP)

Practice questions

India (BIS) recommends

  1. first-angle projection
  2. third-angle projection
  3. second-angle projection
  4. perspective
Show the answer

Answer: A. first-angle projection SP 46.

In first-angle projection the top view is placed

  1. above the front view
  2. below the front view
  3. to the left
  4. anywhere
Show the answer

Answer: B. below the front view Object between observer and plane.

A line perpendicular to the HP appears in the top view as

  1. a point
  2. its true length
  3. a shortened line
  4. a circle
Show the answer

Answer: A. a point Projectors coincide.

A point 20 mm above HP and 30 mm in front of VP lies in the

  1. 1st quadrant
  2. 2nd quadrant
  3. 3rd quadrant
  4. 4th quadrant
Show the answer

Answer: A. 1st quadrant Above HP, in front of VP.

The true length of a line is seen in a view to which the line is

  1. perpendicular
  2. parallel
  3. inclined
  4. oblique
Show the answer

Answer: B. parallel Parallel to the plane.

The point where a line meets the HP is its

  1. VT
  2. HT
  3. end point
  4. midpoint
Show the answer

Answer: B. HT Horizontal trace.

A cylinder resting on its base in the HP shows in the top view a

  1. rectangle
  2. circle
  3. triangle
  4. ellipse
Show the answer

Answer: B. circle True-shape base.

The number of principal planes of projection is

  1. 1
  2. 2
  3. 3
  4. 4
Show the answer

Answer: C. 3 HP, VP and profile plane.

Projectors in orthographic projection are

  1. converging
  2. parallel and perpendicular to the plane
  3. inclined
  4. curved
Show the answer

Answer: B. parallel and perpendicular to the plane Definition.

The front view of a cone resting on its base in the HP is a

  1. circle
  2. triangle
  3. rectangle
  4. trapezium
Show the answer

Answer: B. triangle Isosceles triangle.

In first-angle projection, front view is placed:

  1. Below the top view
  2. Above the top view
  3. To the right
  4. None
Show the answer

Answer: A. Below the top view Below the top view (European standard)

In third-angle projection, front view placed:

  1. Above the top view
  2. Below top view
  3. To the left
  4. None
Show the answer

Answer: A. Above the top view Above the top view (American standard)

Hidden lines are shown as:

  1. Chain lines
  2. Solid thin lines
  3. Dashed lines
  4. None
Show the answer

Answer: C. Dashed lines

Centre lines shown as:

  1. Solid lines
  2. Long-short-long alternating dashes
  3. None
  4. Dashed lines
Show the answer

Answer: B. Long-short-long alternating dashes

Cutting plane line is:

  1. None
  2. Thick chain line with arrows showing viewing direction
  3. Dashed line
  4. Solid thin line
Show the answer

Answer: B. Thick chain line with arrows showing viewing direction

Datum in GD&T is:

  1. Reference feature from which measurements are made
  2. Any surface
  3. None
  4. Random point
Show the answer

Answer: A. Reference feature from which measurements are made

Flatness tolerance ensures:

  1. All points on surface lie between two parallel planes
  2. Cylindrical
  3. Circular shape
  4. None
Show the answer

Answer: A. All points on surface lie between two parallel planes

Circularity (roundness) tolerance:

  1. None
  2. All points on circle lie between two concentric circles
  3. Flatness
  4. Straightness
Show the answer

Answer: B. All points on circle lie between two concentric circles

Title block includes:

  1. None
  2. Instrument list
  3. Process conditions only
  4. Drawing number, scale, material, projection symbol, date, name
Show the answer

Answer: D. Drawing number, scale, material, projection symbol, date, name

Dimensioning rule - dimension should be placed:

  1. Inside always
  2. Randomly
  3. Outside the view if possible, clearly readable
  4. On the object
Show the answer

Answer: C. Outside the view if possible, clearly readable

Welding symbol reference line is:

  1. None
  2. Dashed line
  3. Vertical line
  4. Horizontal line with arrow pointing to weld joint
Show the answer

Answer: D. Horizontal line with arrow pointing to weld joint

Auxiliary view is:

  1. Top view
  2. Front view
  3. View projected onto plane other than principal planes to show true shape of inclined surface
  4. None
Show the answer

Answer: C. View projected onto plane other than principal planes to show true shape of inclined surface

Third angle symbol on drawing:

  1. Circle with cone pointing right
  2. No symbol needed
  3. Circle with cone left
  4. None
Show the answer

Answer: A. Circle with cone pointing right Circle with cone pointing right (truncated cone symbol)

Datum feature symbol in GD&T:

  1. None
  2. Diamond
  3. Circle
  4. Capital letter in box with triangle leader pointing to feature
Show the answer

Answer: D. Capital letter in box with triangle leader pointing to feature

Symmetry tolerance:

  1. None
  2. Flatness
  3. Profile tolerance
  4. Controls median plane/points relative to datum plane
Show the answer

Answer: D. Controls median plane/points relative to datum plane Controls median plane/points relative to datum plane - replaced by positional tolerance in ISO 2017

DRF (Datum Reference Frame):

  1. Three mutually perpendicular datum planes established from datum features for GD&T measurements
  2. Not needed
  3. None
  4. Single datum only
Show the answer

Answer: A. Three mutually perpendicular datum planes established from datum features for GD&T measurements

Primary, secondary, tertiary datums:

  1. Primary
  2. 2 datums only
  3. None
  4. All same
Show the answer

Answer: A. Primary Primary: 3 points; Secondary: 2 points; Tertiary: 1 point - constrain all 6 DOF

Sections, development of surfaces and isometric projection

Topics: Sectional views, section planes and hatching, true shape of a section; development of prisms, pyramids, cylinders and cones; isometric scale, isometric projection and isometric view of simple solids.

Why and how a solid is cut

Dashed lines become confusing when an object has much hidden detail inside. So we imagine a plane cutting it, remove the part between the plane and the viewer, and draw what remains. The cut surface is hatched with thin lines at 45° to the main outline, evenly spaced.

When the plane is perpendicular to the VP and inclined to the HP, it shows as a straight line in the front view. Mark where this line cuts each edge, and project these points down to the top view to obtain the sectional top view.

The section still looks foreshortened in that view. Its true shape is found on an auxiliary plane parallel to the cut: draw a new reference line X₁Y₁ parallel to the cutting line, draw projectors at right angles to it, and set off each point’s distance from XY as measured in the top view.

Example: A cylinder of 50 mm diameter stands on the HP, and a plane perpendicular to the VP cuts it at 45° to the HP. What is the true shape of the section?

  1. The plane cuts all the generators, so the section is an ellipse.
  2. Its minor axis equals the diameter: 50 mm.
  3. Its major axis is the length of the cutting line inside the cylinder: 50/cos 45°.
  4. 50/0.7071 = 70.7 mm.

Answer: An ellipse with a major axis of 70.7 mm and a minor axis of 50 mm.

Isometric projection and the isometric scale

An isometric view shows three faces in one picture. Its three axes make 120° with one another. Vertical edges stay vertical, and the others are drawn at 30° to the horizontal. Since all three axes are equally inclined to the viewing plane, all edges shrink by the same factor, √(2/3) ≈ 0.816.

An isometric drawing ignores this shrinking and uses true lengths. The picture has the same shape but is about 22.5% larger, and it is much quicker to make. A true isometric projection uses the isometric scale, which you construct by comparing a 45° line carrying true lengths with a 30° line.

Example: A block measures 40 × 30 × 20 mm. Find the lengths used in an isometric projection, and in an isometric drawing.

  1. Isometric length = 0.816 × true length.
  2. 40 × 0.816 = 32.6 mm.
  3. 30 × 0.816 = 24.5 mm.
  4. 20 × 0.816 = 16.3 mm.
  5. An isometric drawing uses 40, 30 and 20 mm directly.

Answer: Projection: 32.6, 24.5 and 16.3 mm. Drawing: 40, 30 and 20 mm.

Circles: the four-centre method

A circle on an isometric face appears as an ellipse. To draw it, enclose it in an isometric square whose side equals the circle’s diameter. Join each obtuse corner to the midpoints of the two opposite sides. These lines cross at two points. The two obtuse corners and these two crossing points are the four centres: draw two large arcs and two small arcs, and they join smoothly.

  • Lines not parallel to the axes (non-isometric lines) do not keep the scale: locate their end points first.
  • To convert isometric to orthographic: choose the front direction, then read widths, heights and depths along the axes.
  • To convert orthographic to isometric: draw a box around the object, then cut away.

Example: A 40 mm circle lies on the top face of a block. What size of isometric square encloses it in an isometric drawing, and in an isometric projection?

  1. In an isometric drawing, true lengths are used: a 40 mm rhombus.
  2. In an isometric projection, lengths are scaled by 0.816: 40 × 0.816 = 32.6 mm.

Answer: 40 mm in the drawing, about 32.6 mm in the projection

How JLEE asks it: sections, development and isometric drawing

Development unfolds a surface flat: a cylinder’s side becomes a rectangle πD long; a cone’s side becomes a sector with angle θ = 360° × r/l, where r is the base radius and l the slant height.

Isometric drawings use the isometric scale: isometric length ≈ 0.816 × true length (√(2/3)). An isometric view (without the scale) uses true lengths and looks larger.

  • cylinder: rectangle πD × h
  • cone: sector angle = 360° r/l
  • isometric length ≈ 0.816 × true length

Example: Find the development of the side of a cylinder of diameter 50 mm and height 60 mm.

  1. Width = πD = π × 50 ≈ 157.1 mm.
  2. A rectangle 157.1 mm × 60 mm.

Answer: 157.1 × 60 mm rectangle

Example: A cone has base radius 30 mm and slant height 60 mm. Find the sector angle of its development.

  1. θ = 360° × 30/60.
  2. = 180°: a semicircle of radius 60 mm.

Answer: 180°

Example: What is the isometric length of a 100 mm edge?

  1. Isometric scale factor ≈ 0.816.
  2. 100 × 0.816 ≈ 81.6 mm.

Answer: ≈ 81.6 mm

A section plane cuts an imaginary part away to expose the interior; cut surfaces are hatched with thin lines at 45°. The true shape of a section appears on a plane parallel to the cutting plane. Development unfolds the surface of a solid into a plane: parallel-line development for prisms and cylinders (rectangle of length πD for a cylinder), radial-line development for pyramids and cones (a sector of angle θ = 360° × r/L for a cone of base radius r and slant height L). In isometric projection the three axes are 120° apart and every length is shortened to 0.816 (isometric scale); an isometric view uses true lengths and is larger by about 22.5%.

  • Isometric scale factor = √(2/3) ≈ 0.816.
  • Circles appear as ellipses in isometric (four-centre method).
  • Development of a cylinder of diameter D and height H: rectangle πD × H.
  • Sector angle of a cone: θ = 360° r/L.
  • Hatching lines are usually at 45° and 1–2 mm apart.

Key formulas

  • isometric length = 0.816 × true length
  • θ = 360° × r/L
  • cylinder development = πD × H

Practice questions

The angle between isometric axes is

  1. 90°
  2. 120°
  3. 60°
  4. 45°
Show the answer

Answer: B. 120° Equal angles.

The isometric scale shortens lengths to about

  1. 0.5
  2. 0.707
  3. 0.816
  4. 0.866
Show the answer

Answer: C. 0.816 √(2/3).

The development of a cylinder is a

  1. sector
  2. rectangle
  3. triangle
  4. trapezium
Show the answer

Answer: B. rectangle πD × H.

The development of a cone is a

  1. rectangle
  2. sector of a circle
  3. triangle
  4. circle
Show the answer

Answer: B. sector of a circle Radial-line development.

A cone of base radius 30 mm and slant height 90 mm develops into a sector of angle

  1. 90°
  2. 120°
  3. 60°
  4. 180°
Show the answer

Answer: B. 120° 360 × 30/90.

Section lines (hatching) are usually drawn at

  1. 30°
  2. 45°
  3. 60°
  4. 90°
Show the answer

Answer: B. 45° BIS practice.

In isometric projection a circle appears as

  1. a circle
  2. an ellipse
  3. a parabola
  4. a rhombus
Show the answer

Answer: B. an ellipse Four-centre approximation.

Radial-line development is used for

  1. prisms
  2. cylinders
  3. pyramids and cones
  4. cubes
Show the answer

Answer: C. pyramids and cones Apex-based surfaces.

The true shape of a section is seen on a plane

  1. perpendicular to the section plane
  2. parallel to the section plane
  3. inclined at 45°
  4. horizontal always
Show the answer

Answer: B. parallel to the section plane Parallel view.

An isometric view (not projection) is drawn with

  1. isometric lengths
  2. true lengths
  3. half lengths
  4. double lengths
Show the answer

Answer: B. true lengths Simplified, larger drawing.

Orthographic projection shows:

  1. 3D perspective
  2. None
  3. 2D views of 3D object
  4. Isometric only
Show the answer

Answer: C. 2D views of 3D object 2D views (front, top, side) of 3D object

Isometric drawing uses:

  1. Two axes
  2. Four axes
  3. Three axes at 120° to each other
  4. Random axes
Show the answer

Answer: C. Three axes at 120° to each other Three axes at 120° to each other (30° to horizontal)

A sectional view shows:

  1. Plan view
  2. Interior details by cutting through object
  3. External view
  4. None
Show the answer

Answer: B. Interior details by cutting through object

Section lines (hatching) indicate:

  1. Material cut in cross-section
  2. Dimension
  3. Surface finish
  4. Weld
Show the answer

Answer: A. Material cut in cross-section Material cut in cross-section (usually 45° lines)

Exploded assembly drawing shows:

  1. Only one part
  2. Cross-section
  3. Parts separated to illustrate assembly sequence
  4. None
Show the answer

Answer: C. Parts separated to illustrate assembly sequence

Break lines for long uniform sections use:

  1. Wavy or zigzag line to indicate portion not shown
  2. Dashed line
  3. Chain line
  4. Solid line
Show the answer

Answer: A. Wavy or zigzag line to indicate portion not shown

Oblique drawing shows:

  1. True 3D
  2. None
  3. Front face in true shape; depth lines at 45°
  4. Only top view
Show the answer

Answer: C. Front face in true shape; depth lines at 45°

Cabinet drawing:

  1. Full depth oblique
  2. Isometric
  3. Oblique drawing with depth foreshortened to 1/2
  4. None
Show the answer

Answer: C. Oblique drawing with depth foreshortened to 1/2

Development (pattern) drawing shows:

  1. Unfolded flat surface of 3D object
  2. Elevation
  3. Cross-section
  4. None
Show the answer

Answer: A. Unfolded flat surface of 3D object Unfolded flat surface of 3D object (sheet metal work)

True length of a line shown in:

  1. Any view
  2. None
  3. View where line is parallel to projection plane
  4. Only isometric
Show the answer

Answer: C. View where line is parallel to projection plane

Solid of revolution section hatching:

  1. Alternating section lines for assembly sections
  2. Same as single part
  3. No hatching
  4. None
Show the answer

Answer: A. Alternating section lines for assembly sections

Cutting plane perpendicular to axis of cylinder gives:

  1. Circle as section
  2. Ellipse
  3. None
  4. Rectangle
Show the answer

Answer: A. Circle as section

Cutting plane at angle to axis of cylinder gives:

  1. Circle
  2. None
  3. Parabola
  4. Ellipse as section
Show the answer

Answer: D. Ellipse as section

Interpenetration of solids is shown by:

  1. None
  2. No special line
  3. Curve of intersection
  4. Dashed line
Show the answer

Answer: C. Curve of intersection Curve of intersection (common boundary where two solids meet)

Isometric axes are at:

  1. None
  2. 90° to each other
  3. 120° to each other; two lower axes at 30° to horizontal
  4. 60°
Show the answer

Answer: C. 120° to each other; two lower axes at 30° to horizontal

Oblique drawing - cavalier projection:

  1. Depth lines at 45°; full depth
  2. Half depth
  3. Quarter depth
  4. None
Show the answer

Answer: A. Depth lines at 45°; full depth Depth lines at 45°; full depth (not foreshortened)

Total runout:

  1. Profile only
  2. Controls cumulative variation of entire surface during rotation
  3. Only at one cross-section
  4. None
Show the answer

Answer: B. Controls cumulative variation of entire surface during rotation

Square cross-section symbol:

  1. □ before dimension
  2. R
  3. Φ
  4. None
Show the answer

Answer: A. □ before dimension □ before dimension (e.g. □25 means 25mm square)

Runout tolerances - circular runout:

  1. None
  2. Controls surface variation at each cross-section during one revolution
  3. Profile tolerance
  4. Total runout
Show the answer

Answer: B. Controls surface variation at each cross-section during one revolution Controls surface variation at each cross-section during one revolution - 2D check

Concentricity tolerance:

  1. Coaxiality
  2. Controls centre of cross-sections relative to datum axis
  3. Runout
  4. None
Show the answer

Answer: B. Controls centre of cross-sections relative to datum axis Controls centre of cross-sections relative to datum axis - stricter than coaxiality

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →