IITIAN1997 STUDIO

Electrical engineering materials and drawing

JLEE EE · 10 practice questions with answers

Practise and take a mock test →

Conductors, insulators, magnetic and semiconductor materials

Topics: Conducting materials: copper, aluminium, ACSR, silver, tungsten, nichrome, eureka, manganin; thermocouples, superconductors; insulating materials, dielectric strength, thermal classes; magnetic materials; semiconductor materials; electrical symbols, machine and wiring drawing.

Conducting materials

Silver is the best conductor, then copper and aluminium. Copper is used for windings and cables; aluminium (lighter and cheaper) and ACSR (aluminium conductor, steel reinforced) for overhead lines. High-resistance alloys: nichrome for heating elements, manganin and constantan (eureka) for standard resistors and shunts because their resistance hardly changes with temperature. Tungsten, with its very high melting point, makes lamp filaments.

  • Silver > copper > aluminium (conductivity)
  • Nichrome: heaters; manganin: standards
  • ACSR for overhead lines

Example: Copper has ρ = 1.72 and aluminium 2.82 × 10⁻⁸ Ω·m. How much more resistance has an aluminium wire of the same size?

  1. Ratio = 2.82/1.72.
  2. ≈ 1.64 times.

Answer: ≈ 1.64 times

Example: Which material suits the shunt of an ammeter?

  1. Its resistance must stay constant as it warms.
  2. Manganin (low temperature coefficient).

Answer: Manganin

Insulating materials

Insulators are rated by dielectric strength (kV/mm) and thermal class, the maximum operating temperature: Y 90 °C, A 105, E 120, B 130, F 155, H 180, C above 180. Common insulators: PVC, XLPE, mica, porcelain, glass, rubber, transformer oil and SF₆ gas.

  • Classes: Y 90, A 105, E 120, B 130, F 155, H 180 °C
  • Dielectric strength in kV/mm
  • Transformer oil insulates and cools

Example: What is the maximum temperature for class F insulation?

  1. Class F is rated to 155 °C.
  2. 155 °C.

Answer: 155 °C

Example: An insulator withstands 10 kV/mm. What thickness is needed for 33 kV with a safety factor of 2?

  1. Design stress = 10/2 = 5 kV/mm.
  2. Thickness = 33/5 = 6.6 mm.

Answer: 6.6 mm

Magnetic and semiconductor materials

Soft magnetic materials (silicon steel, ferrites) have narrow hysteresis loops and low losses, ideal for transformer and motor cores; laminating them cuts eddy-current loss. Hard magnetic materials (Alnico, ferrite, neodymium magnets) keep their magnetism for permanent magnets. Hysteresis loss per cycle is proportional to the loop area.

Semiconductors: silicon (band gap ≈ 1.1 eV) and germanium (≈ 0.67 eV); doping with pentavalent atoms gives n-type, trivalent gives p-type.

  • Soft: narrow loop, cores; hard: wide loop, magnets
  • Laminations reduce eddy loss
  • Si 1.1 eV; Ge 0.67 eV

Example: Why are transformer cores laminated?

  1. Thin insulated sheets break up the eddy-current paths.
  2. This reduces eddy-current loss and heating.

Answer: To reduce eddy-current loss

Silver has the lowest resistivity but copper is the practical conductor, and aluminium is used where weight matters; ACSR is aluminium conductor steel reinforced for overhead lines. High-resistivity alloys are nichrome (heaters), manganin and eureka/constantan (standard resistors, with low temperature coefficient). Tungsten’s high melting point suits lamp filaments. Insulators are rated by dielectric strength and thermal class (Y 90 °C, A 105, E 120, B 130, F 155, H 180). Soft magnetic materials such as silicon steel suit transformer cores (low hysteresis), and hard magnetic materials suit permanent magnets (Alnico). Superconductors lose resistance below a critical temperature.

  • Copper conductivity reference: 100% IACS.
  • Transformer oil cools and insulates; test its dielectric strength.
  • Mica has high dielectric strength and heat resistance.
  • Silicon and germanium are semiconductors, doped to n- or p-type.
  • Thermocouple materials: copper–constantan, chromel–alumel.

Key formulas

  • ρ₂ = ρ₁[1 + α(T₂ − T₁)]
  • Class A = 105 °C, Class H = 180 °C

Practice questions

The best conductor at room temperature is

  1. copper
  2. silver
  3. aluminium
  4. gold
Show the answer

Answer: B. silver Lowest resistivity.

Heating elements use

  1. copper
  2. nichrome
  3. silver
  4. aluminium
Show the answer

Answer: B. nichrome High resistivity and temperature.

Standard resistors use

  1. manganin
  2. iron
  3. tungsten
  4. silver
Show the answer

Answer: A. manganin Low temperature coefficient.

Lamp filaments are made of

  1. tungsten
  2. copper
  3. nichrome
  4. aluminium
Show the answer

Answer: A. tungsten High melting point.

ACSR conductors are used for

  1. overhead lines
  2. house wiring
  3. motor windings
  4. PCBs
Show the answer

Answer: A. overhead lines Steel-reinforced strength.

Transformer cores use

  1. silicon steel
  2. copper
  3. cast iron
  4. Alnico
Show the answer

Answer: A. silicon steel Low hysteresis.

Permanent magnets use

  1. Alnico
  2. silicon steel
  3. mica
  4. copper
Show the answer

Answer: A. Alnico Hard magnetic.

Class A insulation is limited to

  1. 90 °C
  2. 105 °C
  3. 155 °C
  4. 180 °C
Show the answer

Answer: B. 105 °C Class A.

Superconductors have below critical temperature

  1. infinite resistance
  2. zero resistance
  3. higher resistance
  4. constant high resistance
Show the answer

Answer: B. zero resistance Definition.

Mica is a

  1. conductor
  2. insulator
  3. semiconductor
  4. magnet
Show the answer

Answer: B. insulator Dielectric.

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →