Distribution, illumination, heating, welding, traction
Topics: Primary and secondary distribution, losses, radial and ring mains; illumination laws and lamps; electric heating and welding; electric traction; electrolysis, electroplating; refrigeration; energy conservation.
Distribution systems
Primary distribution (11 kV) feeds distribution transformers; secondary distribution (415/230 V, three-phase four-wire) feeds consumers. Radial systems are simple but a fault cuts everyone beyond it; ring mains supply each point from two directions. Voltage drop in a distributor = current × loop resistance.
- 11 kV primary; 415/230 V secondary
- Ring main: two paths
- Drop = I × loop resistance
Example: A two-wire distributor carries 20 A with a loop resistance of 0.5 Ω. Find the voltage drop.
- V = 20 × 0.5.
- = 10 V.
Answer: 10 V
Example: Why is a ring main more reliable than a radial feeder?
- Each point is fed from two directions.
- A fault on one section can be isolated while the rest stays supplied.
Answer: Supply from two directions
Illumination
Illuminance (lux) falls with the square of distance: E = I/d²; on a tilted surface E = I cos θ/d². The lumen method gives the number of lamps N = E × A/(Φ × UF × MF), where UF is the utilisation factor and MF the maintenance factor. LEDs give well over 100 lumens per watt, far more than incandescent lamps (about 12–15).
- E = I/d²
- Lumen method: N = EA/(Φ UF MF)
- LEDs: highest efficacy
Example: A 100 cd lamp hangs 2 m above a table. Find the illuminance directly below.
- E = 100/2².
- = 25 lux.
Answer: 25 lux
Example: A 50 m² room needs 300 lux using 3000 lm lamps (UF 0.5, MF 0.8). How many lamps?
- N = 300 × 50/(3000 × 0.5 × 0.8) = 12.5.
- Use 13 lamps.
Answer: 13
Heating, welding, traction and electrolysis
Electric heating: resistance (ovens, heaters), induction (melting, cooking), dielectric (drying wood, plastics). Faraday’s law of electrolysis: mass deposited m = ZIt (Z the electrochemical equivalent), used in electroplating and refining. Traction uses DC series or three-phase induction motors for their high starting torque; regenerative braking returns energy.
- m = ZIt
- Heater: P = mcΔT/(t × η)
- Traction: high starting torque
Example: Copper (Z = 0.000329 g/C) is plated at 10 A for 1 hour. Find the mass deposited.
- m = 0.000329 × 10 × 3600.
- ≈ 11.8 g.
Answer: ≈ 11.8 g
Example: A heater must warm 10 L of water from 20 °C to 80 °C in 30 min at 90 % efficiency. Find its power.
- Heat = 10 × 4186 × 60 ≈ 2.51 MJ; over 1800 s = 1395 W.
- At 90 %: ≈ 1550 W.
Answer: ≈ 1.55 kW
Distribution steps voltage down to 11 kV and 415/240 V, with radial feeders being simple and ring mains more reliable. Illuminance follows the inverse square law E = I cos θ/d², in lux. LEDs have the highest efficacy among common lamps. Resistance heating uses Joule’s law; induction heating suits metals, and dielectric heating suits insulators. Arc welding uses low voltage, high current, with transformers or generators. Electric traction uses DC series motors (or modern AC) for high starting torque. Faraday’s law of electrolysis gives mass m = ZIt. Energy use is reduced by better power factor, efficient lamps and variable speed drives.
- 1 lux = 1 lumen/m².
- Utilisation factor = lumens reaching the plane/lumens emitted.
- Regenerative braking returns energy to the supply.
- Mass deposited m = ZIt.
- Three-phase 4-wire distribution offers 415 V line, 240 V phase.
Key formulas
- E = I cos θ/d²
- m = ZIt
- H = I²Rt
- V_L = √3 V_ph
Practice questions
The unit of illuminance is
- lumen
- lux
- candela
- watt
Show the answer
Answer: B. lux lm/m².
Illuminance varies with distance as
- d
- 1/d
- 1/d²
- d²
Show the answer
Answer: C. 1/d² Inverse square law.
Traction uses mainly DC
- series motors
- shunt motors
- compound motors
- stepper motors
Show the answer
Answer: A. series motors High starting torque.
Faraday’s law of electrolysis gives
- m = ZIt
- E = IR
- P = VI
- F = BIl
Show the answer
Answer: A. m = ZIt Mass deposited.
Arc welding requires
- high voltage, low current
- low voltage, high current
- no current
- only DC series motors
Show the answer
Answer: B. low voltage, high current Stable arc.
Ring mains compared with radial feeders offer
- less reliability
- better continuity
- no protection
- no cost
Show the answer
Answer: B. better continuity Supply from both sides.
Induction heating suits
- metals
- wood
- plastic only
- glass only
Show the answer
Answer: A. metals Eddy currents.
Dielectric heating suits
- insulators
- copper
- steel
- aluminium
Show the answer
Answer: A. insulators Dielectric loss.
Regenerative braking
- returns energy to supply
- wastes energy in resistors
- uses air only
- locks wheels
Show the answer
Answer: A. returns energy to supply Motor acts as generator.
Line voltage of a 240 V phase system is about
- 240 V
- 415 V
- 110 V
- 11 kV
Show the answer
Answer: B. 415 V √3 × 240.
The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.