IITIAN1997 STUDIO

Petroleum technology

JLEE CHE · 10 practice questions with answers

Practise and take a mock test →

Origin, exploration, drilling and production

Topics: Nature and composition of petroleum; petroleum geology, reservoir rock properties (porosity, permeability, saturation), traps; exploration by geological and geophysical methods; drilling methods, drilling fluids, well completion; production and recovery.

Petroleum geology and the reservoir

Petroleum forms from buried organic matter cooked under heat and pressure, migrates upward and collects in porous, permeable reservoir rock (sandstone, limestone) under an impermeable cap rock, in a trap (anticline, fault, salt dome, stratigraphic). Assam’s Digboi field (oil found in 1889) is among the oldest in the world.

Porosity φ is the pore fraction of the rock; permeability is how easily fluid flows through it; saturation is the fraction of pore space filled by water, oil or gas.

  • Source rock → reservoir → trap with cap rock
  • Porosity = pore volume/bulk volume
  • Original oil in place ∝ area × thickness × φ × (1 − Sw)

Example: A 100 cm³ core has 20 cm³ of pores. Find its porosity.

  1. φ = 20/100.
  2. = 0.20 = 20 %.

Answer: 20 %

Example: Estimate oil in place: area 640 acres, thickness 30 ft, φ = 0.2, Sw = 0.3, Bo = 1.2 (N = 7758 A h φ (1 − Sw)/Bo, barrels).

  1. N = 7758 × 640 × 30 × 0.2 × 0.7 / 1.2.
  2. ≈ 1.74 × 10⁷ barrels.

Answer: ≈ 17 million bbl

Drilling

Rotary drilling turns a bit on a drill string; drilling mud is pumped down the pipe and returns up the annulus carrying cuttings, cooling the bit and, through its hydrostatic pressure, holding back formation fluids to prevent blowouts. Casing is cemented in stages; the well is completed with perforations and a wellhead (Christmas tree).

  • Mud: carries cuttings, cools, controls pressure
  • Hydrostatic p = ρgh (0.052 × ppg × ft psi)
  • Casing and cementing seal the well

Example: Find the hydrostatic pressure of 10 ppg mud at 10 000 ft.

  1. p = 0.052 × 10 × 10 000.
  2. = 5200 psi.

Answer: 5200 psi

Example: In SI: mud of 1200 kg/m³ at 3000 m depth.

  1. p = 1200 × 9.81 × 3000.
  2. ≈ 35.3 MPa.

Answer: ≈ 35 MPa

Production and recovery

Primary recovery uses the reservoir’s own energy (solution gas, gas cap, water drive) and typically recovers 10–25 % of the oil. Secondary recovery injects water or gas to maintain pressure; enhanced (tertiary) methods use heat, gases such as CO₂, or chemicals. Artificial lift (sucker-rod pumps, gas lift, electric submersible pumps) helps when pressure falls.

Water cut is the fraction of water in the produced liquid; it rises as the field matures.

  • Primary 10–25 %; water flood adds more
  • Artificial lift when pressure falls
  • Water cut = water/total liquid

Example: A well produces 700 bbl of oil and 300 bbl of water a day. Find the water cut.

  1. Water cut = 300/(700 + 300).
  2. = 30 %.

Answer: 30 %

Oil forms from buried organic matter, migrates through permeable rock and collects in a reservoir below an impervious cap rock, held in a structural or stratigraphic trap. Porosity is the fraction of rock that is pore space and sets the storage; permeability sets how readily fluid flows. Exploration uses gravity, magnetic and, most importantly, seismic surveys. Rotary drilling turns a bit on a drill string while drilling mud cools the bit, carries cuttings up and balances formation pressure. A blowout preventer guards against uncontrolled flow, and a Christmas tree of valves controls a completed well. Recovery starts with natural drive (primary), then water or gas injection (secondary), then enhanced methods (tertiary).

  • Assam’s Digboi field is among the oldest in the world; Digboi refinery dates from 1901.
  • Cable-tool drilling is the older percussion method.
  • Bentonite is a common mud additive; barite raises mud density.
  • Casing strengthens the bore and is cemented in place.
  • Natural gas is mainly methane.

Key formulas

  • Porosity φ = V_pores/V_bulk
  • Darcy: q = kAΔp/(μL)

Practice questions

The storage capacity of a reservoir rock depends on

  1. porosity
  2. colour
  3. hardness
  4. magnetism
Show the answer

Answer: A. porosity Pore space.

Ease of fluid flow through rock is

  1. permeability
  2. porosity
  3. viscosity
  4. density
Show the answer

Answer: A. permeability Connected pores.

The most widely used exploration method is

  1. seismic
  2. pacing
  3. chain survey
  4. dowsing
Show the answer

Answer: A. seismic Geophysical.

Drilling mud does NOT serve to

  1. refine crude oil
  2. cool the bit
  3. lift cuttings
  4. balance formation pressure
Show the answer

Answer: A. refine crude oil Refining happens elsewhere.

Mud density is raised with

  1. barite
  2. salt water only
  3. sand
  4. oil
Show the answer

Answer: A. barite High-density mineral.

Uncontrolled flow from a well is prevented by the

  1. blowout preventer
  2. Christmas tree only
  3. derrick
  4. mud pit
Show the answer

Answer: A. blowout preventer BOP.

Water flooding is a

  1. secondary recovery method
  2. primary recovery method
  3. drilling method
  4. refining process
Show the answer

Answer: A. secondary recovery method Injection to maintain pressure.

Natural gas is mainly

  1. methane
  2. butane
  3. propane
  4. ethylene
Show the answer

Answer: A. methane CH₄.

The impervious layer holding oil in place is the

  1. cap rock
  2. reservoir rock
  3. source rock
  4. casing
Show the answer

Answer: A. cap rock Seal.

Assam’s historic oil town with an early refinery is

  1. Digboi
  2. Silchar
  3. Tezpur
  4. Dhubri
Show the answer

Answer: A. Digboi Refinery from 1901.

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →