IITIAN1997 STUDIO

Size reduction, separation, filtration, mixing (Unit Operation-III and IV)

JLEE CHE · 342 practice questions with answers

Practise and take a mock test →

Size reduction, screening, separation and mixing

Topics: Particle size and shape, sphericity, screen analysis, Tyler mesh; size-reduction laws (Rittinger, Kick, Bond) and equipment (jaw and gyratory crushers, roll crushers, ball mill, hammer mill); critical speed of a ball mill; screening and effectiveness; settling (Stokes’ law), thickening, sedimentation; filtration (cake and filter media, filter aids, plate-and-frame, rotary drum); centrifuges, cyclones, bag filters, electrostatic precipitators; mixing and agitation; conveying.

Particle size and screen analysis

Particle size is measured by sieving (Tyler or IS sieves), described by mesh number (openings per inch). A 200-mesh Tyler screen has 74 µm openings. Shape is described by sphericity: the surface area of a sphere with the same volume divided by the particle’s actual surface area (1 for a sphere, about 0.81 for a cube).

Screen effectiveness compares the oversize recovered in the overflow and the undersize in the underflow with the ideal separation.

  • 200 mesh ≈ 74 µm
  • Sphericity ≤ 1 (sphere = 1)
  • Cumulative analysis gives the size distribution

Example: Find the sphericity of a cube.

  1. Sphericity = π^(1/3)(6V)^(2/3)/A; for a cube of edge 1, V = 1, A = 6.
  2. = π^(1/3) × 6^(2/3) / 6 ≈ 0.806.

Answer: ≈ 0.81

Example: What is the opening of a 200-mesh Tyler screen?

  1. Standard Tyler value.
  2. 0.074 mm (74 µm).

Answer: 74 µm

Size reduction and the ball mill

Energy laws: Rittinger (fine grinding) E = K_R(1/D₂ − 1/D₁), proportional to new surface; Kick (coarse crushing) E = K_K ln(D₁/D₂), the same energy for the same reduction ratio; Bond (in between) W = 10 Wi (1/√P − 1/√F) with sizes in µm.

Jaw and gyratory crushers for coarse, roll crushers for intermediate, ball and hammer mills for fine grinding. A ball mill runs at 65–80 % of its critical speed n_c = 42.3/√(D − d) rpm, at which the balls would centrifuge.

  • Kick: E ∝ ln(D₁/D₂)
  • Rittinger: E ∝ (1/D₂ − 1/D₁)
  • n_c = 42.3/√(D − d) rpm (D, d in m)

Example: By Kick’s law, crushing 50 → 10 mm needs E. What does 10 → 2 mm need?

  1. Both have a reduction ratio of 5.
  2. Kick’s law gives the same energy: E.

Answer: E (the same)

Example: Find the critical speed of a 1.2 m mill with 50 mm balls, and a suitable running speed.

  1. n_c = 42.3/√(1.2 − 0.05) ≈ 39.4 rpm.
  2. At 75 %: about 29.6 rpm.

Answer: ≈ 39 rpm; run ≈ 30 rpm

Settling, filtration and mixing

A small particle falling through a fluid reaches a terminal velocity given by Stokes’ law (Re < 1): v = g d²(ρp − ρ)/(18μ). Thickeners and classifiers use the difference in settling speeds. Centrifuges multiply g to settle fine particles.

Filtration builds a cake whose resistance grows with the volume filtered; filter aids keep compressible cakes porous. Mixers: propellers and turbines for liquids; ribbon blenders and tumblers for powders.

  • v = g d²(ρp − ρ)/18μ (Re < 1)
  • v ∝ d²
  • Cake resistance grows with filtrate volume

Example: Find the settling velocity of 50 µm sand (ρ = 2650) in water (μ = 0.001 Pa·s).

  1. v = 9.81 × (50 × 10⁻⁶)² × 1650 / (18 × 0.001).
  2. ≈ 2.25 × 10⁻³ m/s = 2.25 mm/s.

Answer: ≈ 2.25 mm/s

Example: If the particle diameter is halved, how does the Stokes velocity change?

  1. v ∝ d².
  2. (1/2)² = 1/4: it falls four times slower.

Answer: one quarter

Rittinger’s law (energy ∝ new surface, 1/D₂ − 1/D₁) suits fine grinding, Kick’s law (energy ∝ ln(D₁/D₂)) coarse crushing, and Bond’s law (energy ∝ 1/√D₂ − 1/√D₁) the intermediate range. Jaw and gyratory crushers handle coarse feed, rolls intermediate, and ball mills fine grinding; a ball mill runs at 65–80% of its critical speed N_c = (1/2π)√(g/(R − r)). Stokes’ law gives the terminal velocity of a small sphere u_t = g d²(ρ_p − ρ)/(18μ) for Re < 1. Filtration through a cake follows Darcy’s law; filter aids (diatomaceous earth) keep fine cakes porous. Cyclones separate dust by centrifugal force, and electrostatic precipitators remove very fine particles with high efficiency.

  • Sphericity of a sphere is 1; all other shapes < 1.
  • Tyler mesh number = openings per linear inch.
  • Ball mill critical speed ∝ 1/√D.
  • Free-crushing vs choke-feeding; open vs closed-circuit grinding.
  • Thickeners increase solids concentration of slurries by settling.

Key formulas

  • u_t = g d²(ρ_p − ρ)/(18μ)
  • N_c = (1/2π)√(g/(R − r))
  • Rittinger: E = K_R(1/D₂ − 1/D₁)
  • Kick: E = K_K ln(D₁/D₂)

Practice questions

Rittinger’s law applies best to

  1. coarse crushing
  2. fine grinding
  3. all sizes
  4. screening
Show the answer

Answer: B. fine grinding Energy ∝ new surface.

Kick’s law is suited to

  1. fine grinding
  2. coarse crushing
  3. filtration
  4. mixing
Show the answer

Answer: B. coarse crushing Energy ∝ ln of size ratio.

A ball mill is operated at about what fraction of its critical speed?

  1. 10–20%
  2. 65–80%
  3. 100%
  4. 150%
Show the answer

Answer: B. 65–80% Cascading action.

Stokes’ law is valid for particle Reynolds number

  1. < 1
  2. > 1000
  3. 500–2×10⁵
  4. any
Show the answer

Answer: A. < 1 Creeping flow.

The sphericity of a sphere is

  1. 0
  2. 0.5
  3. 1
  4. > 1
Show the answer

Answer: C. 1 Definition.

A jaw crusher is a

  1. primary crusher
  2. fine grinder
  3. ultrafine mill
  4. screen
Show the answer

Answer: A. primary crusher Coarse feed.

Filter aids are used to

  1. increase cake resistance
  2. keep the cake porous
  3. dissolve the cake
  4. heat the slurry
Show the answer

Answer: B. keep the cake porous Diatomaceous earth.

Very fine dust is removed most efficiently by

  1. a cyclone
  2. a settling chamber
  3. an electrostatic precipitator
  4. a screen
Show the answer

Answer: C. an electrostatic precipitator High-efficiency.

Mesh number of a screen is

  1. opening size in mm
  2. openings per linear inch
  3. wire diameter
  4. area of openings
Show the answer

Answer: B. openings per linear inch Tyler series.

The terminal velocity in Stokes’ range varies with particle diameter as

  1. d
  2. d²
  3. √d
  4. 1/d
Show the answer

Answer: B. d² u_t ∝ d².

For a cylinder whose length equals its diameter, the surface-to-volume shape factor (relative to a sphere of the same diameter) is

  1. 1.5
  2. 0.5
  3. 1.0
  4. 2.0
Show the answer

Answer: C. 1.0

In the Taylor screen series, the aperture of one screen divided by that of the next finer screen is

  1. 2
  2. √2
  3. 1.5
  4. √3
Show the answer

Answer: B. √2

The aperture of a 200-mesh Taylor screen is about

  1. 0.0074 cm
  2. 0.0074 mm
  3. 0.0047 cm
  4. 74 milli-microns
Show the answer

Answer: A. 0.0074 cm

Cumulative analysis gives specific surface more accurately than differential analysis because

  1. assumption that all particles in a single fraction are equal in size.
  2. fact that screening is more effective.
  3. assumption that all particles in a single fraction are equal in size, is not needed.
  4. none of these.
Show the answer

Answer: C. assumption that all particles in a single fraction are equal in size, is not needed.

The equivalent diameter of a particle is the diameter of a sphere having the same

  1. ratio of surface to volume as the actual volume.
  2. ratio of volume to surface as the particle.
  3. volume as the particle.
  4. none of these.
Show the answer

Answer: B. ratio of volume to surface as the particle.

Soft, non-abrasive materials are reduced to fines mainly by

  1. attrition
  2. compression
  3. cutting
  4. none of these
Show the answer

Answer: A. attrition

Crushing efficiency is the ratio of

  1. surface energy created by crushing to the energy absorbed by the solid.
  2. energy absorbed by the solid to that fed to the machine.
  3. energy fed to the machine to the surface energy created by crushing.
  4. energy absorbed by the solid to the surface energy created by crushing.
Show the answer

Answer: A. surface energy created by crushing to the energy absorbed by the solid.

Rittinger’s law states that the work of crushing is proportional to

  1. work required to form a particle of any size is proportional to the square of the surface to volume ratio.
  2. work required is proportional to the square root of the surface to volume ratio.
  3. work required in crushing is proportional to the new surface created.
  4. crushing efficiency is dependent on the size of the feed and product.
Show the answer

Answer: C. work required in crushing is proportional to the new surface created.

Bond’s crushing law

  1. calls for relatively less energy for the smaller product particles, than does the Rittinger law.
  2. is less realistic in estimating the power requirements of commercial crushers.
  3. states that work required is proportional to the square root of the volume to surface ratio.
  4. states that the work required for crushing is proportional to the new surface created.
Show the answer

Answer: A. calls for relatively less energy for the smaller product particles, than does the Rittinger law.

The work index is defined as the energy (kWh per ton) needed to reduce a very large feed until 80 % of the product passes a

  1. gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen
  2. energy needed to crush one tonne of feed to 200 microns.
  3. energy needed to crush small feed so 80% passes a 200 mesh screen.
  4. energy needed to crush one ton of feed to 100 microns.
Show the answer

Answer: A. gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen

A ball mill should run at a speed

  1. less than
  2. much more than
  3. at least equal to
  4. slightly more than
Show the answer

Answer: A. less than

A fluid-energy mill is used for

  1. cutting
  2. grinding
  3. ultragrinding
  4. crushing
Show the answer

Answer: C. ultragrinding

Compared with dry grinding in a revolving mill, wet grinding

  1. gives less wear on chamber walls
  2. requires more energy
  3. increases capacity
  4. complicates handling of the product
Show the answer

Answer: C. increases capacity

Cement clinker is ground finely in a

  1. roll crusher
  2. ball mill
  3. tube mill
  4. hammer mill
Show the answer

Answer: C. tube mill

In a fertiliser plant, molten ammonium nitrate is mixed with ground limestone in a

  1. pug mill
  2. mixer-extruder
  3. banbury mixer
  4. muller mixer
Show the answer

Answer: A. pug mill

For primary breaking of hard rock, use a

  1. gyratory crusher
  2. ball mill
  3. tube mill
  4. squirrel-cage disintegrator
Show the answer

Answer: A. gyratory crusher

Fibrous material is broken down in a

  1. roll crusher
  2. squirrel-cage disintegrator
  3. ball mill
  4. tube mill
Show the answer

Answer: B. squirrel-cage disintegrator

As the product is ground finer, the energy needed

  1. decreases
  2. increases
  3. is same as for coarser grinding
  4. is 1.5 times that for coarser grinding
Show the answer

Answer: B. increases

Increasing the throughput of a screen makes its effectiveness

  1. decreases
  2. increases
  3. does not effect
  4. none of these
Show the answer

Answer: A. decreases

Screen effectiveness (efficiency) equals

  1. recovery/rejection
  2. recovery
  3. rejection
  4. none of these
Show the answer

Answer: D. none of these

Traces of suspended solids are removed from a liquid in a

  1. classifier
  2. clarifier
  3. sparkler filter
  4. rotary vacuum filter
Show the answer

Answer: B. clarifier

A vacuum filter is best suited to

  1. removal of fines from liquid.
  2. liquids having high vapour pressure.
  3. liquids of very high viscosity.
  4. none of these.
Show the answer

Answer: A. removal of fines from liquid.

A filter aid is added mainly to

  1. increase the rate of filtration.
  2. decrease the pressure drop.
  3. increase the porosity of the cake.
  4. act as a support base for the septum.
Show the answer

Answer: C. increase the porosity of the cake.

Filter-medium resistance is the resistance of

  1. filter cloth.
  2. embedded particles in the septum.
  3. filter cloth and the embedded particle collectively.
  4. none of these.
Show the answer

Answer: C. filter cloth and the embedded particle collectively.

While a filter cake is being washed,

  1. all the resistances are constant.
  2. filter medium resistance increases.
  3. filter medium resistance decreases.
  4. cake resistance decreases.
Show the answer

Answer: A. all the resistances are constant.

In a compressible cake, porosity is

  1. minimum at the filter medium.
  2. minimum at the upstream face.
  3. maximum at the filter medium.
  4. same throughout the thickness of cake.
Show the answer

Answer: A. minimum at the filter medium.

The unit of specific cake resistance is

  1. gm/cm²
  2. cm/gm
  3. cm/gm²
  4. gm/gm
Show the answer

Answer: B. cm/gm

Filter-medium resistance is governed by

  1. pressure drop alone
  2. flow rate alone
  3. both pressure drop and flow rate
  4. cake thickness
Show the answer

Answer: C. both pressure drop and flow rate

For a completely compressible cake, the compressibility coefficient is

  1. 0
  2. 1
  3. 0 to 1
  4. ∞
Show the answer

Answer: B. 1

In continuous filtration at constant pressure drop, the filtrate rate varies inversely as the

  1. square root of filtration time
  2. square of viscosity
  3. filtration time
  4. washing time
Show the answer

Answer: A. square root of filtration time

To separate sugar solution from settled mud, use a

  1. sparkler
  2. plate and frame
  3. centrifugal
  4. rotary drum vacuum
Show the answer

Answer: C. centrifugal

Water is removed from lubricating oil in a

  1. tubular centrifuge
  2. clarifier
  3. sparkler filter
  4. vacuum leaf filter
Show the answer

Answer: A. tubular centrifuge

Dust-laden air is commonly cleaned in a

  1. cyclone separator
  2. bag filter
  3. gravity settler
  4. tubular centrifuge
Show the answer

Answer: A. cyclone separator

The most widely used filter aid is

  1. diatomaceous earth
  2. calcium silicate
  3. sodium carbonate
  4. silica gel
Show the answer

Answer: A. diatomaceous earth

Activated carbon is separated from glycerine with a

  1. plate and frame filter
  2. rotary vacuum filter
  3. batch basket centrifuge
  4. none of these
Show the answer

Answer: A. plate and frame filter

Paper mills filter water through a

  1. open sand
  2. plate and frame
  3. vacuum leaf
  4. sparkler
Show the answer

Answer: A. open sand

A rotary drum vacuum filter typically turns at about ____ rpm.

  1. 1
  2. 50
  3. 100
  4. 500
Show the answer

Answer: A. 1

A gelatinous solid that blinds the cloth is best filtered on a ____ filter.

  1. sparkler
  2. plate and frame
  3. vacuum leaf
  4. precoat
Show the answer

Answer: D. precoat

A screen is “blinded” when

  1. oversizes are present in undersize fraction.
  2. undersizes are retained in oversize fraction.
  3. screen is plugged with solid particles.
  4. screen capacity is abruptly increased.
Show the answer

Answer: C. screen is plugged with solid particles.

The size of ultrafine particles is best stated as

  1. centimetre
  2. screen size
  3. micron
  4. surface area per unit mass
Show the answer

Answer: D. surface area per unit mass

Ultrafine grinders work mainly by

  1. slow compression
  2. impact
  3. attrition
  4. cutting action
Show the answer

Answer: C. attrition

Trommels separate particles according to their

  1. size
  2. density
  3. wettability
  4. electrical and magnetic properties
Show the answer

Answer: A. size

The energy used by a ball mill depends on

  1. its speed.
  2. its ball load.
  3. the density of the material being ground.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

The grinding efficiency of a ball mill is only about ____ %.

  1. 1-5
  2. 40-50
  3. 75-80
  4. 90-95
Show the answer

Answer: A. 1-5

Screen capacity is expressed as

  1. tons/hr
  2. tons/ft²
  3. both (a) and (b)
  4. tons/hr-ft²
Show the answer

Answer: D. tons/hr-ft²

Which screen has the highest capacity?

  1. Grizzlies
  2. Trommels
  3. Shaking screen
  4. Vibrating screen
Show the answer

Answer: D. Vibrating screen

Separating particles of different size, shape and density by settling in a fluid is called

  1. classification
  2. froth floatation
  3. thickening
  4. clarification
Show the answer

Answer: A. classification

Iron ore is most commonly beneficiated by

  1. flocculation.
  2. froth floatation.
  3. jigging and tabling.
  4. none of these.
Show the answer

Answer: C. jigging and tabling.

Froth flotation is best suited to

  1. iron ores
  2. sulphide ores
  3. quartzite
  4. none of these
Show the answer

Answer: B. sulphide ores

Compared with free crushing, choke crushing

  1. results in increased capacity.
  2. consumes less power.
  3. consumes more power.
  4. both (a) and (c).
Show the answer

Answer: C. consumes more power.

A sticky material is best conveyed by a

  1. Apron conveyor
  2. Belt conveyor
  3. Screw conveyor
  4. Pneumatic conveyor
Show the answer

Answer: C. Screw conveyor

Ore concentration by jigging depends on differences in

  1. specific gravities
  2. wettability
  3. shape
  4. none of these
Show the answer

Answer: A. specific gravities

The Chance process is used for

  1. cleaning of coal.
  2. concentration of iron ore.
  3. concentration of pyrites.
  4. water treatment
Show the answer

Answer: A. cleaning of coal.

If a basket centrifuge’s radius is halved and its speed doubled, then the

  1. linear speed of the basket is doubled.
  2. linear speed of the basket is halved.
  3. centrifugal force is doubled.
  4. capacity of centrifuge is increased.
Show the answer

Answer: C. centrifugal force is doubled.

Two liquids with a very small density difference are best separated in a

  1. disc bowl centrifuge.
  2. sharples super centrifuge.
  3. batch basket centrifuge.
  4. sparkler filter.
Show the answer

Answer: B. sharples super centrifuge.

Fine materials are best sized on a

  1. trommel
  2. grizzly
  3. shaking screen
  4. vibrating screen
Show the answer

Answer: D. vibrating screen

Which conveyor is not recommended for abrasive materials?

  1. Belt conveyor
  2. Apron conveyor
  3. Flight conveyor
  4. Chain conveyor
Show the answer

Answer: C. Flight conveyor

In froth flotation, the reagent that makes particles cling to air bubbles is a

  1. collector
  2. frother
  3. modifier
  4. activator
Show the answer

Answer: A. collector

In froth flotation, pine oil acts as a

  1. collector
  2. modifier
  3. frother
  4. activator
Show the answer

Answer: C. frother

The float-and-sink test checks whether coal can be cleaned by

  1. gravity separation
  2. wettability
  3. particle shape
  4. none of these
Show the answer

Answer: A. gravity separation

A paddle agitator

  1. is suitable for mixing low viscosity liquids.
  2. produces axial flow.
  3. moves at very high speed.
  4. none of these.
Show the answer

Answer: A. is suitable for mixing low viscosity liquids.

Very viscous liquids and pastes are agitated with

  1. propellers
  2. turbine agitators
  3. multiple blade paddles
  4. none of these
Show the answer

Answer: C. multiple blade paddles

A propeller agitator

  1. produces mainly axial flow.
  2. is used for mixing high viscosity pastes.
  3. runs at very slow speed (2 rpm).
  4. all (a), (b) and (c)
Show the answer

Answer: A. produces mainly axial flow.

A helical-screw agitator is used for

  1. mixing highly viscous pastes.
  2. blending immiscible liquids.
  3. mixing liquids at very high temperature (>250°C).
  4. none of these.
Show the answer

Answer: A. mixing highly viscous pastes.

Which filter may be unsuitable for volatile liquids?

  1. Pressure filter
  2. Gravity filter
  3. Centrifugal filter
  4. Vacuum filter
Show the answer

Answer: D. Vacuum filter

In a washing-type plate-and-frame press, washing rate divided by the final filtration rate is

  1. 4
  2. 1/4
  3. 1
  4. 1/2
Show the answer

Answer: B. 1/4

For efficient grinding, a ball mill must run

  1. at a speed less than the critical speed.
  2. at a speed more than the critical speed.
  3. at a speed equal to the critical speed.
  4. with minimum possible small balls.
Show the answer

Answer: A. at a speed less than the critical speed.

Ultrafine powders are transported with a ____ conveyor.

  1. belt
  2. pneumatic
  3. screw
  4. none of these
Show the answer

Answer: B. pneumatic

Ultrafine particles are produced in a

  1. ball mill
  2. rod mill
  3. hammer crusher
  4. fluid energy mill
Show the answer

Answer: D. fluid energy mill

A gyratory crusher breaks material mainly by

  1. impact
  2. compression
  3. attrition
  4. cutting
Show the answer

Answer: B. compression

Mesh number is the number of openings per

  1. square inch
  2. linear inch
  3. square foot
  4. linear foot
Show the answer

Answer: B. linear inch

Fine talc powder is made from granules in a

  1. roller crusher
  2. ball mill
  3. jaw crusher
  4. gyratory crusher
Show the answer

Answer: B. ball mill

Pasty material is conveyed by a

  1. apron conveyor
  2. belt conveyor
  3. screw conveyor
  4. bucket elevator
Show the answer

Answer: C. screw conveyor

Diatomaceous earth is used as a

  1. explosive
  2. filter aid
  3. filter medium
  4. catalyst
Show the answer

Answer: B. filter aid

A ball mill is used for

  1. crushing
  2. coarse grinding
  3. fine grinding
  4. attrition
Show the answer

Answer: C. fine grinding

The capacity of a belt conveyor depends on its

  1. speed
  2. thickness
  3. length
  4. none of these.
Show the answer

Answer: A. speed

Dry powdery solids are commonly moved by a ____ conveyor.

  1. belt
  2. bucket
  3. screw
  4. none of these
Show the answer

Answer: C. screw

Grizzlies are used to separate ____ solids.

  1. coarse
  2. fine
  3. any size
  4. none of these
Show the answer

Answer: A. coarse

Cyclones are used mainly to separate

  1. solids
  2. solids from fluids
  3. liquids
  4. solids from solids
Show the answer

Answer: B. solids from fluids

A tube mill differs from a ball mill mainly in

  1. length to diameter ratio.
  2. size of the grinding media.
  3. final product size.
  4. operating speed.
Show the answer

Answer: A. length to diameter ratio.

Apron conveyors are used for

  1. heavy loads and short runs.
  2. small loads and long runs.
  3. heavy loads and long runs.
  4. none of these.
Show the answer

Answer: A. heavy loads and short runs.

The sphericity of a Raschig ring whose length equals its diameter is

  1. >1
  2. <1
  3. 1
  4. 2
Show the answer

Answer: B. <1

The sphericity of pulverised coal particles is

  1. 1
  2. <1
  3. >1
  4. ∞
Show the answer

Answer: B. <1

Particles of different densities are separated in a

  1. filters
  2. thickness
  3. cyclones
  4. sorting classifier
Show the answer

Answer: D. sorting classifier

A plot of the reciprocal of filtration rate against filtrate volume is a straight line for

  1. compressible cakes and laminar
  2. incompressible cake and laminar
  3. compressible cake and turbulent
  4. incompressible cake and turbulent
Show the answer

Answer: B. incompressible cake and laminar

A 200-mesh screen has 200 openings per linear

  1. cm²
  2. cm
  3. inch
  4. inch²
Show the answer

Answer: C. inch

For constant-pressure filtration, a plot of filtrate volume against time is a

  1. Parabola
  2. Straight line
  3. Hyperbola
  4. Exponential curve
Show the answer

Answer: A. Parabola

Raising the drum speed of a rotary drum filter makes the filtration rate

  1. increases
  2. increases linearly
  3. decreases
  4. is not affected
Show the answer

Answer: A. increases

Large-scale sedimentation is carried out in

  1. classifiers
  2. rotary drum filters
  3. thickeners
  4. cyclones
Show the answer

Answer: C. thickeners

In constant-rate filtration, the inlet pressure

  1. increases continuously
  2. decreases gradually
  3. remains constant
  4. none of these
Show the answer

Answer: A. increases continuously

The critical speed of a ball mill (mill radius R₁, ball radius R₂) is

  1. Nc = (1/4π)·√(g/(R₁-R₂))
  2. Nc = (1/2π)·√(g/(R₁-R₂))
  3. Nc = (1/π)·√(g/(R₁-R₂))
  4. Nc = (1/2π)·√((R₁-R₂)/g)
Show the answer

Answer: B. Nc = (1/2π)·√(g/(R₁-R₂))

For a roll crusher (roll diameter d_r, feed d_f, product gap d_p), half the angle of nip α satisfies

  1. cos α = (dr+dp)/(dr+df)
  2. cos α = (dr+df)/(dr+dp)
  3. tan α = (dr+dp)/(dr+df)
  4. sin α = (dr+dp)/(dr+df)
Show the answer

Answer: A. cos α = (dr+dp)/(dr+df)

The mass flow of granular solids through a circular orifice of diameter D varies as

  1. M ∝ √D
  2. M ∝ D²
  3. M ∝ D^2.5
  4. M ∝ D
Show the answer

Answer: C. M ∝ D^2.5

In screen analysis, “−10 mm +5 mm” means particles that

  1. 10 mm screen and retained on 5 mm screen.
  2. 5 mm screen and retained on 10 mm screen.
  3. both 5 mm and 10 mm screens.
  4. neither 5 mm nor 10 mm screen.
Show the answer

Answer: A. 10 mm screen and retained on 5 mm screen.

The critical speed N of a trommel varies with its diameter D as

  1. N ∝ 1/√D
  2. N ∝ √D
  3. N ∝ D
  4. N ∝ 1/D
Show the answer

Answer: A. N ∝ 1/√D

The equivalent diameter of a 3 cm × 6 cm rectangular channel is about ____ cm.

  1. 20
  2. 12
  3. 8
  4. 4
Show the answer

Answer: D. 4

For a non-spherical particle, sphericity

  1. is the surface area of a sphere of equal volume divided by the particle’s actual surface area.
  2. has the dimension of length.
  3. is always greater than 1.
  4. is the volume of a sphere of equal surface area divided by the actual volume.
Show the answer

Answer: A. is the surface area of a sphere of equal volume divided by the particle’s actual surface area.

Which law gives the crushing energy as proportional to the new surface created?

  1. Taggarts rule
  2. Fick's law
  3. Rittinger's law
  4. none of these
Show the answer

Answer: C. Rittinger's law

If the equivalent diameter of a cube is taken as its edge length, its sphericity is

  1. 0.5
  2. 1
  3. √2
  4. √3
Show the answer

Answer: B. 1

The sphericity of Raschig rings is

  1. 0.5
  2. 1
  3. <1
  4. √3
Show the answer

Answer: C. <1

As screen capacity rises, screen effectiveness

  1. remains unchanged
  2. increases
  3. decreases
  4. decreases exponentially
Show the answer

Answer: C. decreases

The specific surface of spheres is proportional to

  1. Dp²
  2. Dp
  3. 1/Dp
  4. 1/Dp²
Show the answer

Answer: C. 1/Dp

A jaw crusher reduces size mainly by

  1. attrition
  2. compression
  3. cutting
  4. impact
Show the answer

Answer: B. compression

A feed of 25 cm lumps can be taken by a

  1. ball mill
  2. rod mill
  3. fluid energy mill
  4. jaw crusher
Show the answer

Answer: D. jaw crusher

In a ball mill, most size reduction comes from

  1. attrition
  2. compression
  3. impact
  4. cutting
Show the answer

Answer: C. impact

The specific surface (per unit mass) of spheres of diameter D and density ρ is

  1. 6/(Dρ)
  2. 2/(Dρ)
  3. 4/(Dρ)
  4. 12/(Dρ)
Show the answer

Answer: A. 6/(Dρ)

With V the volume, S the surface and D the equivalent diameter of a particle, sphericity equals

  1. 6V/(D.S)
  2. V/(6D.S)
  3. D.S/V
  4. σ·V/(D.S)
Show the answer

Answer: A. 6V/(D.S)

For grinders, the reduction ratio is defined as (D_f feed, D_p product)

  1. Df/Dp
  2. Dp/Df
  3. Df·Dp
  4. none of these
Show the answer

Answer: A. Df/Dp

Fine grinders can have reduction ratios

  1. 5-10
  2. 10-20
  3. 20-40
  4. as high as 100
Show the answer

Answer: D. as high as 100

Filter aid is added to a slurry to

  1. increase the porosity
  2. increase the compressibility co-efficient
  3. decrease the porosity
  4. decrease the compressibility co-efficient
Show the answer

Answer: A. increase the porosity

Which material has the lowest Rittinger number (hardest to create new surface)?

  1. Calcite
  2. Pyrite
  3. Quartz
  4. Galena
Show the answer

Answer: C. Quartz

The crushing efficiency of machines is only about ____ %.

  1. 0.1 to 2
  2. 5 to 10
  3. 20 to 25
  4. 50 to 70
Show the answer

Answer: A. 0.1 to 2

By Bond’s law, the work to produce particles of size D from a very large feed is proportional to

  1. (S/V)p
  2. √(S/V)p
  3. (S/V)p²
  4. (S/V)f
Show the answer

Answer: B. √(S/V)p

In a rotary drum vacuum filter, the controlling resistance is the

  1. piping
  2. cake
  3. filter medium
  4. none of these
Show the answer

Answer: B. cake

Run-of-mine coal for domestic use is usually crushed in a

  1. jaw crusher
  2. hammer crusher
  3. ball mill
  4. tube mill
Show the answer

Answer: B. hammer crusher

During filtration, the filtrate meets the resistance of

  1. filter medium.
  2. cake.
  3. channel carrying the slurry to the upstream side of the cake.
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

During washing of a cake, all resistances

  1. increases
  2. decreases
  3. remain constant
  4. none of these
Show the answer

Answer: C. remain constant

In a plate-and-frame press, flow of filtrate through the cake is

  1. plug
  2. turbulent
  3. laminar
  4. none of these
Show the answer

Answer: C. laminar

Which is a filter aid?

  1. Canvas fabric
  2. Diatomaceous earth
  3. Calcined lime
  4. None of these
Show the answer

Answer: B. Diatomaceous earth

In constant-pressure filtration, the filtrate rate

  1. continuously increases.
  2. continuously decreases.
  3. remains constant throughout.
  4. may increase or decrease; depends on the pressure.
Show the answer

Answer: B. continuously decreases.

Sorting classifiers that use differential settling depend on differences in

  1. particle sizes
  2. densities
  3. terminal velocities
  4. none of these
Show the answer

Answer: C. terminal velocities

Screw conveyors are

  1. run at very high speed.
  2. suitable for sticky materials.
  3. ideal for highly abrasive materials.
  4. none of these.
Show the answer

Answer: B. suitable for sticky materials.

A belt conveyor can

  1. run upto 1 km.
  2. travel at a speed upto 300 metres/minute.
  3. handle materials upto 5000 tons/hr.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

The maximum slope for a belt conveyor is about

  1. 15°
  2. 30°
  3. 45°
  4. 60°
Show the answer

Answer: B. 30°

Bucket elevators are NOT suited to lifting ____ materials.

  1. fine (e.g. -200 mesh size coal)
  2. sticky (e.g. clay paste)
  3. small lumpy (e.g. grains and sand)
  4. free flowing
Show the answer

Answer: B. sticky (e.g. clay paste)

The reduction ratio of a crusher is

  1. ratio of feed opening to discharge opening.
  2. ratio of discharge opening to feed opening.
  3. determining factor for minimum dia of the feed and the product.
  4. none of these.
Show the answer

Answer: A. ratio of feed opening to discharge opening.

The grindability of a material does NOT depend on its

  1. elasticity
  2. hardness
  3. toughness
  4. size
Show the answer

Answer: D. size

The softest of these minerals is

  1. Talc
  2. Feldspar
  3. Corundum
  4. Calcite
Show the answer

Answer: A. Talc

The hardest of these minerals is

  1. Calcite
  2. Quartz
  3. Corundum
  4. Gypsum
Show the answer

Answer: C. Corundum

For grinding coal to −200 mesh in a ball mill, the energy is best estimated by

  1. Rittinger's law
  2. Kick's law
  3. Bond's law
  4. none of these
Show the answer

Answer: A. Rittinger's law

A 200-mesh sieve corresponds to about ____ microns.

  1. 24
  2. 74
  3. 154
  4. 200
Show the answer

Answer: B. 74

In ball-mill grinding,

  1. wet grinding achieves a finer product size than dry grinding.
  2. its capacity decreases with increasing fineness of the products.
  3. grinding cost and power requirement increases with increasing fineness.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

In a hammer crusher,

  1. crushing takes place by impact breaking.
  2. maximum acceptable feed size is 30 cms.
  3. reduction ratio can be varied by adjusting the distance from cage to hammers.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Compared with a ball mill, a tube mill

  1. has a higher length/diameter ratio.
  2. produces a coarser product.
  3. has a higher diameter/length ratio.
  4. uses much larger balls.
Show the answer

Answer: A. has a higher length/diameter ratio.

In a ball mill,

  1. coarse feed requires a larger ball.
  2. fine feed requires a larger ball.
  3. operating speed should be more than the critical speed.
  4. none of these
Show the answer

Answer: A. coarse feed requires a larger ball.

In a roll crusher, the rolls

  1. have the same diameter.
  2. rotate towards each other.
  3. may run at the same or different speeds.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

The power to drive a ball mill with a given ball load varies with mill diameter D as

  1. D
  2. 1/D
  3. D^2.5
  4. 1/D^2.5
Show the answer

Answer: C. D^2.5

Closed-circuit grinding in an air-swept ball mill uses a

  1. classifier.
  2. cyclone separator between mill and classifier.
  3. both (a) and (b).
  4. neither (a) nor (b).
Show the answer

Answer: A. classifier.

In a hammer crusher, size reduction is mainly by

  1. attrition
  2. impact
  3. both (a) and (b)
  4. neither (a) nor (b)
Show the answer

Answer: B. impact

Which equipment grinds ultrafine mainly by attrition?

  1. Jet mills
  2. Fluid energy mill
  3. Micronizer
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

Wheat is milled into flour with a

  1. hammer crusher
  2. roller crusher
  3. impact mill
  4. fluid energy mill
Show the answer

Answer: B. roller crusher

Limestone is normally crushed in a

  1. roll crusher
  2. hammer crusher
  3. ball mill
  4. tube mill
Show the answer

Answer: B. hammer crusher

Coal is pulverised to 200 mesh for boiler firing in a

  1. hammer crusher
  2. ball mill
  3. roll crusher
  4. gyratory crusher
Show the answer

Answer: B. ball mill

Which is a primary crusher for hard, tough stone?

  1. Jaw crusher
  2. Cone crusher
  3. Ball mill
  4. None of these
Show the answer

Answer: A. Jaw crusher

Which is a secondary crusher for hard, tough stone?

  1. Jaw crusher
  2. Cone crusher
  3. Impact crusher
  4. Toothed roll crusher
Show the answer

Answer: B. Cone crusher

Carbon black is pulverised in a

  1. hammer crusher
  2. ball mill
  3. roll crusher
  4. gyratory crusher
Show the answer

Answer: B. ball mill

In a compressible cake, porosity is highest

  1. maximum porosity at the upstream side.
  2. maximum porosity at the filter medium.
  3. same porosity throughout the cake thickness.
  4. none of these.
Show the answer

Answer: A. maximum porosity at the upstream side.

The largest feed size is accepted by a

  1. tube mill
  2. ball mill
  3. jaw crusher
  4. jet pulveriser
Show the answer

Answer: C. jaw crusher

The electrical energy used by a jaw crusher is NOT a function of

  1. average feed size
  2. average product size
  3. machine capacity
  4. none of these
Show the answer

Answer: D. none of these

Reducing 300–1500 mm feed to 100–300 mm product is

  1. secondary
  2. fine
  3. primary
  4. ultrafine
Show the answer

Answer: C. primary

In froth flotation, xanthates act as

  1. conditioner
  2. frother
  3. collector
  4. activator
Show the answer

Answer: C. collector

Screen capacity does NOT depend on

  1. its openings size.
  2. screening mechanism.
  3. screening surface.
  4. atmospheric humidity.
Show the answer

Answer: D. atmospheric humidity.

Gold ore is commonly concentrated by

  1. jigging
  2. tabling
  3. froth floatation
  4. elutriation
Show the answer

Answer: B. tabling

Which is an activator in froth flotation?

  1. Cresylic acid
  2. Copper sulphate
  3. Calcium carbonate
  4. Sodium carbonate
Show the answer

Answer: B. Copper sulphate

Trommels usually turn at about ____ rpm.

  1. 1-2
  2. 15-20
  3. 40-50
  4. 60-75
Show the answer

Answer: B. 15-20

The fluid used for classification in mineral dressing can be

  1. air
  2. water
  3. either (a) or (b)
  4. neither (a) nor (b)
Show the answer

Answer: C. either (a) or (b)

Pine oil and cresylic acid act as ____ in froth flotation.

  1. frother
  2. collector
  3. depressor
  4. conditioner
Show the answer

Answer: A. frother

Reducing 100–300 mm feed to 10–50 mm product is

  1. primary
  2. secondary
  3. fine
  4. ultrafine
Show the answer

Answer: B. secondary

The Sauter mean diameter is the same as the ____ mean diameter.

  1. mass
  2. arithmetic
  3. volume-surface
  4. geometric
Show the answer

Answer: C. volume-surface

Gummy, sticky materials such as molasses are best moved by a ____ conveyor.

  1. drag
  2. ribbon
  3. screw
  4. slat
Show the answer

Answer: B. ribbon

Hot, lumpy, abrasive materials are best carried by a ____ conveyor.

  1. apron
  2. belt
  3. screw
  4. flight
Show the answer

Answer: A. apron

Which of these is a coarse crusher?

  1. Smooth roll crusher
  2. Toothed roll crusher
  3. Gyratory crusher
  4. Tube mill
Show the answer

Answer: C. Gyratory crusher

Which mills are called impactors?

  1. Hammer
  2. Cage
  3. Rolling-compression
  4. none of these
Show the answer

Answer: A. Hammer

Stamp mills are traditionally used for crushing

  1. iron ores
  2. gold ores
  3. talc
  4. diamond
Show the answer

Answer: B. gold ores

Fibrous materials like wood, asbestos and mica are reduced in a

  1. Blake jaw crusher
  2. cage mill
  3. stamp mill
  4. Bradford's breaker
Show the answer

Answer: D. Bradford's breaker

Balls for ball mills are never made of

  1. forged/cast steel
  2. lead
  3. cast iron
  4. alloy steel
Show the answer

Answer: B. lead

For maximum capacity, the ball charge should fill about ____ % of the mill volume.

  1. 10
  2. 25
  3. 50
  4. 75
Show the answer

Answer: C. 50

Among these, which crusher gives the finest product?

  1. Blake jaw crusher
  2. Gyratory crusher
  3. Toothed roll crusher
  4. Dodge jaw crusher
Show the answer

Answer: C. Toothed roll crusher

Cereals, grains and spices are traditionally ground in a

  1. Buhrstone mill
  2. ball mill
  3. crushing rolls
  4. hammer mill
Show the answer

Answer: A. Buhrstone mill

Which material is reduced in steam-heated rollers and roll crushers?

  1. resins
  2. gums
  3. hard rubber
  4. waxes
Show the answer

Answer: C. hard rubber

Grain, gravel, sand and ash over short distances are moved by a ____ conveyor.

  1. flight
  2. slat or drag
  3. ribbon
  4. screw
Show the answer

Answer: A. flight

Sugar mills usually use a ____ centrifuge.

  1. Tubular bowl
  2. Disc-bowl
  3. Suspended batch basket
  4. Perforated horizontal basket continuous
Show the answer

Answer: C. Suspended batch basket

A mixer resembling a ball mill without balls is a ____ mixer.

  1. banbery
  2. pug mill
  3. tumbling
  4. pan
Show the answer

Answer: C. tumbling

Ultracentrifuges separate ____ particles.

  1. coarse
  2. fine
  3. colloidal
  4. dissolved
Show the answer

Answer: C. colloidal

Flocculation can be promoted by adding

  1. electrolyte
  2. surface active agent
  3. both (a) and (b)
  4. neither (a) nor (b)
Show the answer

Answer: C. both (a) and (b)

Filtration in a filter press should be stopped when

  1. cake becomes very dense.
  2. liquor stops flowing out to the discharge.
  3. filtration pressure rises suddenly.
  4. both (b) and (c).
Show the answer

Answer: D. both (b) and (c).

Filtration with a continuously rising slurry inlet pressure is called

  1. constant rate
  2. varying pressure
  3. varying rate
  4. constant pressure
Show the answer

Answer: A. constant rate

The constants in the Bond, Rittinger and Kick laws depend on

  1. feed material.
  2. type of crushing machine.
  3. both (a) and (b).
  4. neither (a) nor (b).
Show the answer

Answer: C. both (a) and (b).

Intermediate and fine grinders reduce size mainly by

  1. cutting action.
  2. compression.
  3. compression and tearing.
  4. impact and attrition.
Show the answer

Answer: D. impact and attrition.

Which of these is NOT a cutting machine?

  1. Dicers
  2. Knife cutters
  3. Slitters
  4. Tube mills
Show the answer

Answer: D. Tube mills

For a given energy input, production rate ____ as the required fineness increases.

  1. decreases
  2. increases
  3. remains unchanged
  4. may increase or decrease; depends on the machine
Show the answer

Answer: A. decreases

The most commonly used filter aid is

  1. Diatomaceous earth
  2. Fuller's earth
  3. Vermiculite
  4. Semi-plastic clay
Show the answer

Answer: A. Diatomaceous earth

Rubber and plastic solids are compounded in a

  1. Banbery mixer
  2. Pan mixer
  3. Pug mill
  4. Charge can mixer
Show the answer

Answer: A. Banbery mixer

Ribbon blenders are used for mixing

  1. Lumpy solids and low viscosity liquids
  2. Dry powders
  3. High viscosity liquids
  4. Thick pastes
Show the answer

Answer: B. Dry powders

Coarse particles are separated from a slurry of fines in a

  1. Thickeners
  2. Classifiers
  3. Hydrocyclones
  4. Decanters
Show the answer

Answer: B. Classifiers

A screen placed across a pipe to catch dirt and rust is a

  1. thickener
  2. classifier
  3. strainer
  4. clarifier
Show the answer

Answer: C. strainer

Removing fine solids from a liquid by settling is called

  1. decantation
  2. flocculation
  3. sedimentation
  4. classification
Show the answer

Answer: C. sedimentation

A gravity decanter separates two

  1. immiscible liquids of different density
  2. miscible liquids of different density
  3. immiscible liquids of same density
  4. miscible liquids of same density
Show the answer

Answer: A. immiscible liquids of different density

Reducing 10–50 mm feed to 2–10 mm product is

  1. primary
  2. secondary
  3. fine
  4. ultrafine
Show the answer

Answer: C. fine

The angle of nip relates to

  1. jaw
  2. roll
  3. gyratory
  4. none of these
Show the answer

Answer: B. roll

Which crusher gives the smallest reduction ratio for a given feed?

  1. Jaw crusher
  2. Roll crusher
  3. Cone crusher
  4. Gyratory crusher
Show the answer

Answer: B. Roll crusher

In a jaw crusher, energy consumed per ton falls with

  1. decreasing size of product at constant size of feed.
  2. decreasing machine capacity.
  3. increasing size of feed at constant reduction ratio.
  4. none of these.
Show the answer

Answer: C. increasing size of feed at constant reduction ratio.

Filtration rate does NOT depend on

  1. pressure drop and area of filtering surface.
  2. resistance of the cake and the septum.
  3. properties of the cake and the filtrate.
  4. none of these.
Show the answer

Answer: D. none of these.

To remove very small amounts of precipitate from a large volume of water, a suitable filter is the

  1. plate and frame
  2. shell and leaf
  3. sand
  4. rotary vacuum
Show the answer

Answer: A. plate and frame

Baffles in agitated vessels reduce

  1. swirling
  2. vortexing
  3. both (a) and (b)
  4. neither (a) nor (b)
Show the answer

Answer: C. both (a) and (b)

Power calculations for mixing involve the

  1. Reynold's
  2. Froude
  3. both (a) and (b)
  4. neither (a) nor (b)
Show the answer

Answer: C. both (a) and (b)

The milligrams of KOH needed to saponify 1 g of oil is its ____ number.

  1. saponification
  2. acid
  3. precipitation
  4. emulsion
Show the answer

Answer: A. saponification

Which is NOT suitable for moving materials along varying paths?

  1. Hand trolley
  2. Belt conveyor
  3. Crane
  4. Truck
Show the answer

Answer: A. Hand trolley

For a paddle agitator, paddle diameter divided by tank diameter is usually up to about

  1. 0.1
  2. 0.8
  3. 0.25
  4. 0.5
Show the answer

Answer: B. 0.8

For a propeller agitator, impeller diameter divided by tank diameter is usually

  1. 0.15-030
  2. 0.5-0.65
  3. 0.75-0.85
  4. 0.60-0.90
Show the answer

Answer: A. 0.15-030

Agitation power depends on the

  1. height & properties of the liquid.
  2. agitator type & speed of agitation.
  3. size of agitator & the tank.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Residence time of solids in a rotary dryer depends on its

  1. rpm
  2. slope & length
  3. flights arrangement
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

Size reduction is achieved by:

  1. Only compression
  2. Only impact
  3. Compression, impact, attrition, and cutting
  4. Heating only
Show the answer

Answer: C. Compression, impact, attrition, and cutting

Jaw crusher uses:

  1. Cutting
  2. Attrition
  3. Compression between fixed and moving jaws for coarse crushing
  4. Impact
Show the answer

Answer: C. Compression between fixed and moving jaws for coarse crushing

Gyratory crusher:

  1. Conical crushing head rotating in conical shell
  2. Impact
  3. Cutting
  4. Attrition
Show the answer

Answer: A. Conical crushing head rotating in conical shell Conical crushing head rotating in conical shell - continuous compression crushing

Ball mill uses:

  1. None
  2. Compression only
  3. Impact and attrition by balls in rotating cylinder
  4. Cutting only
Show the answer

Answer: C. Impact and attrition by balls in rotating cylinder Impact and attrition by balls in rotating cylinder - fine grinding

Rod mill vs ball mill:

  1. Same output
  2. Rod mill coarser product; less over-grinding; rods provide line contact
  3. Ball mill coarser
  4. None
Show the answer

Answer: B. Rod mill coarser product; less over-grinding; rods provide line contact

Hammer mill uses:

  1. None
  2. Cutting
  3. Impact of rotating hammers for intermediate size reduction
  4. Compression
Show the answer

Answer: C. Impact of rotating hammers for intermediate size reduction

Bond's law of size reduction:

  1. None
  2. Kick's law
  3. Rittinger's law
  4. Energy ∝
Show the answer

Answer: D. Energy ∝ Energy ∝ (1/√Dp − 1/√Df) - intermediate sizes

Rittinger's law:

  1. None
  2. Kick's law
  3. Energy ∝ new surface area created
  4. Bond's law
Show the answer

Answer: C. Energy ∝ new surface area created Energy ∝ new surface area created (fine grinding)

Kick's law applies to:

  1. Fine grinding
  2. Intermediate
  3. Coarse crushing
  4. None
Show the answer

Answer: C. Coarse crushing Coarse crushing: energy ∝ ln(Df/Dp)

Screen analysis measures:

  1. Density
  2. Shape
  3. Particle size distribution using series of sieves
  4. None
Show the answer

Answer: C. Particle size distribution using series of sieves

Tyler standard screen series:

  1. Ratio = 1.5
  2. Ratio of adjacent sieve openings = √2
  3. Ratio = 2
  4. None
Show the answer

Answer: B. Ratio of adjacent sieve openings = √2 Ratio of adjacent sieve openings = √2 (or 1.41)

Cyclone separator uses:

  1. Centrifugal force to separate particles from gas without moving parts
  2. Filtration
  3. None
  4. Gravity settling only
Show the answer

Answer: A. Centrifugal force to separate particles from gas without moving parts

Bag filter (fabric filter) removes:

  1. Fine particles from gas stream; efficiency > 99% for PM2.5
  2. Gas molecules
  3. None
  4. Coarse particles only
Show the answer

Answer: A. Fine particles from gas stream; efficiency > 99% for PM2.5

Electrostatic precipitator (ESP):

  1. None
  2. Filter-based
  3. Cyclone-based
  4. Charges particles in corona discharge; collected on grounded plates
Show the answer

Answer: D. Charges particles in corona discharge; collected on grounded plates

Settling velocity (Stokes Law): v ∝

  1. dp² for laminar settling regime
  2. dp
  3. dp³
  4. 1/dp
Show the answer

Answer: A. dp² for laminar settling regime dp² (particle diameter squared) for laminar settling regime

Stokes Law valid for:

  1. Re > 1000
  2. Re = 100
  3. Reynolds number Re_p < 1
  4. None
Show the answer

Answer: C. Reynolds number Re_p < 1 Reynolds number (particle) Re_p < 1 (laminar flow around particle)

Terminal velocity of particle:

  1. Zero velocity
  2. None
  3. Maximum possible
  4. Velocity where drag = gravitational force; particle settles at constant velocity
Show the answer

Answer: D. Velocity where drag = gravitational force; particle settles at constant velocity

Elutriator separates:

  1. By density alone
  2. None
  3. By size alone
  4. Fine particles by upward gas stream
Show the answer

Answer: D. Fine particles by upward gas stream Fine particles by upward gas stream (those with v_terminal < gas velocity are carried away)

Gravity settling chamber:

  1. None
  2. Cyclone type
  3. Large chamber where gas velocity drops; coarse particles settle by gravity
  4. Removes fine particles
Show the answer

Answer: C. Large chamber where gas velocity drops; coarse particles settle by gravity Large chamber where gas velocity drops; coarse particles (>50 µm) settle by gravity

Wet scrubber advantages:

  1. Removes both particulate and gaseous pollutants simultaneously; cools gas
  2. None
  3. Only removes gas
  4. Only removes particles
Show the answer

Answer: A. Removes both particulate and gaseous pollutants simultaneously; cools gas

Venturi scrubber:

  1. High-velocity gas + liquid droplets in venturi throat
  2. None
  3. Gravity scrubber
  4. Packed scrubber
Show the answer

Answer: A. High-velocity gas + liquid droplets in venturi throat High-velocity gas + liquid droplets in venturi throat - collects particles

Filtration: pressure drop across cake ∝

  1. Constant
  2. Flow rate only
  3. None
  4. Thickness of cake (Ruth's filtration equation
Show the answer

Answer: D. Thickness of cake (Ruth's filtration equation Thickness of cake (Ruth's filtration equation: −dV/dt ∝ V)

Filter medium resistance:

  1. None
  2. Zero
  3. Resistance of filter cloth/medium
  4. Cake only
Show the answer

Answer: C. Resistance of filter cloth/medium Resistance of filter cloth/medium (in addition to cake resistance)

Plate and frame filter press:

  1. None
  2. Batch filtration; frames hold cake; plates hold medium
  3. Continuous filter
  4. Rotary filter
Show the answer

Answer: B. Batch filtration; frames hold cake; plates hold medium

Rotary vacuum filter:

  1. Continuous filtration; drum rotates through slurry; vacuum applied inside
  2. None
  3. Press filter
  4. Batch filter
Show the answer

Answer: A. Continuous filtration; drum rotates through slurry; vacuum applied inside

Centrifuge types:

  1. Only batch
  2. Only continuous
  3. Basket, decanter, disc
  4. None
Show the answer

Answer: C. Basket, decanter, disc Basket (batch), decanter (continuous), disc (continuous)

Sigma factor (Σ) of centrifuge:

  1. Separation efficiency
  2. Speed only
  3. None
  4. Area of settling that centrifuge is equivalent to
Show the answer

Answer: D. Area of settling that centrifuge is equivalent to Area of settling that centrifuge is equivalent to: Σ = V·ω²/2g for simple bowl

Sedimentation vs centrifugation:

  1. No difference
  2. None
  3. Centrifuge slower
  4. Centrifugation uses g-forces
Show the answer

Answer: D. Centrifugation uses g-forces Centrifugation uses g-forces (hundreds to thousands times gravity) - much faster

Fluidisation occurs when:

  1. None
  2. Pressure drop across bed equals weight of particles per unit area
  3. Any flow rate
  4. Low flow rate only
Show the answer

Answer: B. Pressure drop across bed equals weight of particles per unit area

Minimum fluidisation velocity (umf):

  1. Maximum velocity
  2. Terminal velocity
  3. Gas velocity at which bed just fluidises; Ergun equation used
  4. None
Show the answer

Answer: C. Gas velocity at which bed just fluidises; Ergun equation used

Bubbling fluidised bed:

  1. None
  2. Gas velocity > umf; excess gas forms bubbles
  3. No bubbles
  4. Dense bed only
Show the answer

Answer: B. Gas velocity > umf; excess gas forms bubbles Gas velocity > umf; excess gas forms bubbles - good mixing, poor gas-solid contact

Spouted bed:

  1. FBB type
  2. None
  3. Central gas jet creates spouting; used for coarse particles
  4. Packed bed
Show the answer

Answer: C. Central gas jet creates spouting; used for coarse particles

Fixed (packed) bed:

  1. Particles stationary; fluid flows through void spaces
  2. Fluidised bed
  3. None
  4. Moving bed
Show the answer

Answer: A. Particles stationary; fluid flows through void spaces Particles stationary; fluid flows through void spaces - good gas-solid contact

Ergun equation gives:

  1. Pressure drop through packed bed as function of velocity, bed geometry, and fluid properties
  2. Filtration rate
  3. None
  4. Settling velocity
Show the answer

Answer: A. Pressure drop through packed bed as function of velocity, bed geometry, and fluid properties

Blake-Kozeny equation (Ergun at low Re):

  1. Turbulent only
  2. Ergun full
  3. ΔP ∝ μuL/ for laminar flow through packed bed
  4. None
Show the answer

Answer: C. ΔP ∝ μuL/ for laminar flow through packed bed ΔP ∝ μuL/(dp²ε³) for laminar flow through packed bed

Conveyor belt efficiency:

  1. Moves bulk solids horizontally or at slight incline; high throughput, low energy
  2. Screw conveyor
  3. None
  4. Pneumatic transport
Show the answer

Answer: A. Moves bulk solids horizontally or at slight incline; high throughput, low energy

Pneumatic conveying - dilute phase:

  1. Particles suspended in high-velocity gas; high wear
  2. None
  3. Dense phase
  4. Mechanical conveying
Show the answer

Answer: A. Particles suspended in high-velocity gas; high wear Particles suspended in high-velocity gas (>15 m/s); high wear

Pneumatic conveying - dense phase:

  1. Slugs or strands of particles at low velocity; less wear, less gas
  2. None
  3. Dilute phase
  4. Mechanical
Show the answer

Answer: A. Slugs or strands of particles at low velocity; less wear, less gas

Screw conveyor:

  1. Pneumatic
  2. None
  3. Belt
  4. Helical screw in tube for horizontal or inclined transport of powders/pastes
Show the answer

Answer: D. Helical screw in tube for horizontal or inclined transport of powders/pastes

Bucket elevator:

  1. Cups on belt/chain for vertical lifting of bulk solids
  2. Conveyor belt
  3. None
  4. Screw
Show the answer

Answer: A. Cups on belt/chain for vertical lifting of bulk solids

Vibrating screen:

  1. None
  2. Sieve with vibration to separate particles by size; easy to clog
  3. Cyclone
  4. Settling chamber
Show the answer

Answer: B. Sieve with vibration to separate particles by size; easy to clog

Trommel screen:

  1. Vibrating screen
  2. Rotating cylindrical screen for coarse size separation
  3. None
  4. Cyclone
Show the answer

Answer: B. Rotating cylindrical screen for coarse size separation

Jigging (mineral processing):

  1. None
  2. Chemical separation
  3. Size separation
  4. Stratification by pulsating water
Show the answer

Answer: D. Stratification by pulsating water Stratification by pulsating water - density separation

Froth flotation:

  1. Filtration
  2. Hydrophobic particles attach to air bubbles and float; used in mineral processing
  3. None
  4. Gravity settling
Show the answer

Answer: B. Hydrophobic particles attach to air bubbles and float; used in mineral processing

Magnetic separation:

  1. Separates magnetic particles from non-magnetic using magnetic field
  2. Density-based
  3. Size-based
  4. None
Show the answer

Answer: A. Separates magnetic particles from non-magnetic using magnetic field Separates magnetic particles (iron, magnetite) from non-magnetic using magnetic field

Electrostatic separation:

  1. None
  2. Density-based
  3. Separates particles with different electrical conductivities using high voltage
  4. Size-based
Show the answer

Answer: C. Separates particles with different electrical conductivities using high voltage

Leaching:

  1. None
  2. Flotation
  3. Filtration
  4. Selective dissolution of soluble components from solid using liquid solvent
Show the answer

Answer: D. Selective dissolution of soluble components from solid using liquid solvent

Spray drying produces:

  1. Films
  2. Powder from liquid droplets dried in hot gas stream
  3. Pellets
  4. None
Show the answer

Answer: B. Powder from liquid droplets dried in hot gas stream

Agglomeration:

  1. Formation of larger particles from fine powder
  2. None
  3. Size reduction
  4. Separation
Show the answer

Answer: A. Formation of larger particles from fine powder Formation of larger particles from fine powder (granulation, pelletisation)

Mixer types for viscous materials:

  1. Propeller
  2. Sigma mixer, Banbury mixer, planetary mixer
  3. None
  4. Turbine agitator
Show the answer

Answer: B. Sigma mixer, Banbury mixer, planetary mixer Sigma (Z-blade) mixer, Banbury mixer, planetary mixer

Power consumption in ball mill ∝

  1. D only
  2. D^3
  3. None
  4. D^2.5 approximately
Show the answer

Answer: D. D^2.5 approximately D^2.5 (mill diameter) approximately - Bond's empirical finding

Critical speed of ball mill:

  1. Minimum speed
  2. Optimal speed
  3. Speed at which centrifugal force equals gravity
  4. None
Show the answer

Answer: C. Speed at which centrifugal force equals gravity Speed at which centrifugal force equals gravity - no grinding above critical speed

Operating speed of ball mill:

  1. 50% critical
  2. None
  3. 65-80% of critical speed for efficient grinding
  4. 100% critical
Show the answer

Answer: C. 65-80% of critical speed for efficient grinding

Attrition mill (stirred media mill):

  1. Agitator stirs media at high speed
  2. None
  3. Compression only
  4. Coarse grinding
Show the answer

Answer: A. Agitator stirs media at high speed Agitator stirs media at high speed - fine grinding < 10 µm - less energy than ball mill

Jet mill (fluid energy mill):

  1. None
  2. Particles accelerated by high-velocity gas jets
  3. Only dry
  4. Wet grinding
Show the answer

Answer: B. Particles accelerated by high-velocity gas jets Particles accelerated by high-velocity gas jets - collide and fracture - ultrafine grinding

Colloid mill:

  1. Dry grinding
  2. Sieving
  3. None
  4. Rotor-stator with narrow gap
Show the answer

Answer: D. Rotor-stator with narrow gap Rotor-stator with narrow gap - reduces particle size in liquid suspensions (emulsions, dispersions)

Homogeniser (high pressure):

  1. None
  2. Forces liquid through narrow valve at high pressure
  3. Only dry
  4. Gravity-based
Show the answer

Answer: B. Forces liquid through narrow valve at high pressure Forces liquid through narrow valve at high pressure - reduces droplet/particle size in emulsions

Particle size distribution parameters:

  1. D10, D50, D90
  2. Only mean
  3. Only range
  4. None
Show the answer

Answer: A. D10, D50, D90 D10, D50, D90 (percentile diameters) - D90 = 90% of particles smaller than this size

Sauter mean diameter (d32):

  1. Median diameter
  2. Volume-surface mean diameter
  3. Arithmetic mean
  4. None
Show the answer

Answer: B. Volume-surface mean diameter Volume-surface mean diameter - relates to surface area per unit volume - used in mass transfer

Laser diffraction particle sizing:

  1. Only sieve
  2. None
  3. Measures angle-dependent light scattering to determine size distribution
  4. Only microscopy
Show the answer

Answer: C. Measures angle-dependent light scattering to determine size distribution Measures angle-dependent light scattering to determine size distribution - 0.1-3000 µm range

Sedimentation particle sizing (Andreasen pipette):

  1. Stokes law-based
  2. Sieving
  3. None
  4. Laser diffraction
Show the answer

Answer: A. Stokes law-based Stokes law-based - withdrawal of samples at intervals; slower but no equipment

Impaction efficiency in cyclone:

  1. Decreases with size
  2. None
  3. Increases with particle size and gas velocity
  4. Constant
Show the answer

Answer: C. Increases with particle size and gas velocity Increases with particle size and gas velocity - coarse particles collected better

Cut size (d50) of cyclone:

  1. None
  2. Particle size at which 50% is collected
  3. Minimum particle
  4. Maximum particle
Show the answer

Answer: B. Particle size at which 50% is collected Particle size at which 50% is collected - smaller cut size = finer separation

Series cyclones:

  1. Single always better
  2. Smaller cyclones in series can achieve finer cut size than single large cyclone
  3. Parallel only
  4. None
Show the answer

Answer: B. Smaller cyclones in series can achieve finer cut size than single large cyclone

Multiclone:

  1. None
  2. Single cyclone
  3. Battery of small parallel cyclones
  4. Fabric filter
Show the answer

Answer: C. Battery of small parallel cyclones Battery of small parallel cyclones - high efficiency for fine particles

Bag filter pulse-jet cleaning:

  1. Mechanical shaking only
  2. Water cleaning
  3. None
  4. Compressed air pulses reverse-clean clogged bags while others continue filtering
Show the answer

Answer: D. Compressed air pulses reverse-clean clogged bags while others continue filtering

ESP efficiency equation:

  1. No equation
  2. η = 1 − exp
  3. None
  4. Linear equation
Show the answer

Answer: B. η = 1 − exp η = 1 − exp(−w·A/Q) (Deutsch-Anderson) - w=drift velocity, A=collection area, Q=gas flow

Wet ESP vs dry ESP:

  1. Wet ESP uses water spray to remove collected particles
  2. None
  3. Same performance
  4. Dry always better
Show the answer

Answer: A. Wet ESP uses water spray to remove collected particles Wet ESP uses water spray to remove collected particles - handles sticky/hygroscopic particles better

Scrubber efficiency depends on:

  1. Only temperature
  2. Gas-liquid contact area, liquid-to-gas ratio, residence time, droplet size
  3. Only liquid rate
  4. None
Show the answer

Answer: B. Gas-liquid contact area, liquid-to-gas ratio, residence time, droplet size

Packed scrubber vs venturi scrubber:

  1. Packed
  2. Always choose packed
  3. None
  4. Always choose venturi
Show the answer

Answer: A. Packed Packed: lower pressure drop, better gas absorption; Venturi: handles high dust, simpler

Cake filtration - constant pressure:

  1. None
  2. Flow rate decreases over time as cake builds
  3. Exponential decrease
  4. Constant flow
Show the answer

Answer: B. Flow rate decreases over time as cake builds Flow rate decreases over time as cake builds - parabolic relationship between V and t

Filter aid (diatomaceous earth, perlite):

  1. None
  2. Reduces flow
  3. Blocks filter
  4. Added to slurry or as pre-coat to improve cake porosity and filtration rate
Show the answer

Answer: D. Added to slurry or as pre-coat to improve cake porosity and filtration rate

Centrifuge G-force calculation:

  1. G = mass/force
  2. None
  3. G = density ratio
  4. G = r·ω²/g
Show the answer

Answer: D. G = r·ω²/g G = r·ω²/g - G-factor = r·ω²/g (dimensionless relative centrifugal force)

Basket centrifuge:

  1. Continuous only
  2. None
  3. Decanter type
  4. Perforated basket spins
Show the answer

Answer: D. Perforated basket spins Perforated basket spins - liquid passes through; cake on walls - batch operation

Decanter centrifuge:

  1. Batch only
  2. Disc type
  3. None
  4. Continuous
Show the answer

Answer: D. Continuous Continuous - solid bowl with screw conveyor; discharges wet solids continuously

Disc stack centrifuge:

  1. Batch only
  2. Low G-force
  3. None
  4. High G-force; for very fine particles and liquid-liquid separation
Show the answer

Answer: D. High G-force; for very fine particles and liquid-liquid separation High G-force (5000-15000 g); for very fine particles and liquid-liquid separation

Fluidised bed advantages over fixed bed:

  1. None
  2. Less mixing
  3. Lower conversion
  4. Better heat and mass transfer; isothermal; handles fine particles; easy solids handling
Show the answer

Answer: D. Better heat and mass transfer; isothermal; handles fine particles; easy solids handling

Circulating fluidised bed (CFB):

  1. Low velocity FBB
  2. High-velocity transport bed with cyclone returning entrained solids
  3. None
  4. Spouted bed
Show the answer

Answer: B. High-velocity transport bed with cyclone returning entrained solids High-velocity transport bed with cyclone returning entrained solids - used in CFB boilers

Pressure drop in fluidised bed:

  1. Zero
  2. ΔP =··g·L
  3. Same as packed bed
  4. None
Show the answer

Answer: B. ΔP =··g·L ΔP = (1−ε)·(ρp−ρf)·g·L - equal to weight of particles per unit area (at fluidisation)

Spouted bed applications:

  1. None
  2. Coating of tablets and seeds; drying of coarse particles
  3. Only fine particles
  4. Only gases
Show the answer

Answer: B. Coating of tablets and seeds; drying of coarse particles Coating of tablets and seeds; drying of coarse particles - food, pharmaceutical

Moving bed reactor:

  1. Only fluidised
  2. None
  3. Solid moves downward, fluid upward
  4. Only fixed
Show the answer

Answer: C. Solid moves downward, fluid upward Solid moves downward, fluid upward - used for catalytic reforming regeneration, blast furnace

Rotary kiln:

  1. Only liquid processing
  2. Rotating inclined cylinder
  3. Only gas processing
  4. None
Show the answer

Answer: B. Rotating inclined cylinder Rotating inclined cylinder - processing solids at high temperature (cement, lime, ore roasting)

Rotary dryer:

  1. None
  2. Slightly inclined rotating cylinder with lifters
  3. Tray dryer
  4. Spray dryer
Show the answer

Answer: B. Slightly inclined rotating cylinder with lifters Slightly inclined rotating cylinder with lifters - direct or indirect drying of granular solids

Spray dryer - co-current vs counter-current:

  1. No difference
  2. None
  3. Co-current
  4. Counter-current always better
Show the answer

Answer: C. Co-current Co-current: inlet hot gas and spray in same direction - protects heat-sensitive materials

Tray (shelf) dryer:

  1. Spray type
  2. None
  3. Trays of material on shelves in heated chamber
  4. Continuous only
Show the answer

Answer: C. Trays of material on shelves in heated chamber Trays of material on shelves in heated chamber - batch, low throughput, labour intensive

Drum dryer:

  1. Spray dryer
  2. Wet material applied to heated rotating drum
  3. None
  4. Tray dryer
Show the answer

Answer: B. Wet material applied to heated rotating drum Wet material applied to heated rotating drum - dried film scraped off

Fluidised bed dryer:

  1. Drum dryer
  2. Tray dryer
  3. High heat and mass transfer; uniform drying; fast; used for granules, powders, crystals
  4. None
Show the answer

Answer: C. High heat and mass transfer; uniform drying; fast; used for granules, powders, crystals

Drying rate curve - constant rate period:

  1. Internal diffusion limits
  2. Both equal
  3. None
  4. Surface evaporation rate = convection rate; temperature = wet bulb temperature
Show the answer

Answer: D. Surface evaporation rate = convection rate; temperature = wet bulb temperature

Falling rate period in drying:

  1. None
  2. Equilibrium
  3. Constant rate
  4. Internal moisture diffusion limits
Show the answer

Answer: D. Internal moisture diffusion limits Internal moisture diffusion limits - rate decreases; critical moisture content boundary

Critical moisture content:

  1. None
  2. Point where falling rate period begins
  3. Final moisture
  4. Initial moisture
Show the answer

Answer: B. Point where falling rate period begins Point where falling rate period begins - depends on material structure

Equilibrium moisture content (EMC):

  1. Zero moisture
  2. Maximum moisture
  3. None
  4. Moisture content at which material neither gains nor loses moisture at given T and RH
Show the answer

Answer: D. Moisture content at which material neither gains nor loses moisture at given T and RH

Psychrometric chart uses:

  1. Only for gases
  2. None
  3. Only for liquids
  4. Determines drying conditions
Show the answer

Answer: D. Determines drying conditions Determines drying conditions - wet/dry bulb T, humidity ratio, enthalpy, dew point

Humidification:

  1. Adding water vapour to gas stream
  2. None
  3. Drying
  4. Filtration
Show the answer

Answer: A. Adding water vapour to gas stream Adding water vapour to gas stream - cooling tower, air conditioning

Dehumidification:

  1. Removing water vapour
  2. Adding moisture
  3. Heating only
  4. None
Show the answer

Answer: A. Removing water vapour Removing water vapour - by cooling below dew point or adsorbent (silica gel, molecular sieves)

Crystallisation driving force:

  1. Pressure only
  2. Supersaturation
  3. None
  4. Temperature only
Show the answer

Answer: B. Supersaturation Supersaturation - solution concentration exceeds solubility; nucleation and growth

Nucleation in crystallisation:

  1. Primary (spontaneous
  2. Only primary
  3. Only secondary
  4. None
Show the answer

Answer: A. Primary (spontaneous Primary (spontaneous - homogeneous, heterogeneous) or secondary (from existing crystals)

Metastable zone in crystallisation:

  1. Region above solubility curve where no spontaneous nucleation
  2. Below solubility curve
  3. Where nucleation is maximum
  4. None
Show the answer

Answer: A. Region above solubility curve where no spontaneous nucleation Region above solubility curve where no spontaneous nucleation - only growth occurs

Draft tube baffle (DTB) crystalliser:

  1. Batch pan only
  2. None
  3. Internal draft tube and baffle create circulation
  4. Forced circulation only
Show the answer

Answer: C. Internal draft tube and baffle create circulation Internal draft tube and baffle create circulation - large uniform crystals

Washing of crystals:

  1. Filtration only
  2. Remove mother liquor by displacement washing or repulping in fresh solvent
  3. Heating to dissolve
  4. None
Show the answer

Answer: B. Remove mother liquor by displacement washing or repulping in fresh solvent Remove mother liquor (impurities) by displacement washing or repulping in fresh solvent

Leaching - counter-current extraction:

  1. None
  2. Maximum concentration driving force
  3. Co-current
  4. Single stage
Show the answer

Answer: B. Maximum concentration driving force Maximum concentration driving force - fresh solvent contacts most extracted solid

Size reduction energy - work index (Wi) in Bond's law:

  1. None
  2. Surface area only
  3. Work index = kWh to reduce 1 tonne from infinite size to 100 µm
  4. Volume only
Show the answer

Answer: C. Work index = kWh to reduce 1 tonne from infinite size to 100 µm Work index = kWh to reduce 1 tonne from infinite size to 100 µm - material specific

Centrifugal pump vs positive displacement:

  1. "
  2. e
  3. [
  4. C
Show the answer

Answer: C. [

NPSH available (NPSHa) calculation:

  1. [
  2. P
  3. N
  4. "
Show the answer

Answer: A. [

Pipe network - Hardy-Cross method:

  1. "
  2. t
  3. I
  4. [
Show the answer

Answer: D. [

Darcy-Weisbach equation for pressure drop:

  1. "
  2. [
  3. P
  4. Δ
Show the answer

Answer: B. [

The Moody chart relates the Darcy friction factor to:

  1. Velocity and viscosity only
  2. Density and pipe diameter
  3. Reynolds number and relative roughness
  4. Pressure drop and pipe length
Show the answer

Answer: C. Reynolds number and relative roughness

Bernoulli's equation limitations:

  1. s
  2. A
  3. [
  4. "
Show the answer

Answer: C. [

Fluidisation - terminal velocity significance:

  1. [
  2. "
  3. f
  4. I
Show the answer

Answer: A. [

Pneumatic conveying pressure drop:

  1. [
  2. n
  3. "
  4. I
Show the answer

Answer: A. [

Rotary kiln L/D ratio:

  1. y
  2. "
  3. [
  4. T
Show the answer

Answer: C. [

Spray dryer inlet temperature:

  1. 5
  2. "
  3. 1
  4. [
Show the answer

Answer: D. [

Crystalliser yield calculation:

  1. "
  2. Y
  3. i
  4. [
Show the answer

Answer: D. [

Washing efficiency in filtration:

  1. [
  2. "
  3. W
  4. a
Show the answer

Answer: A. [

Thickener underflow concentration:

  1. "
  2. e
  3. D
  4. [
Show the answer

Answer: D. [

Counter-current decantation (CCD):

  1. "
  2. L
  3. e
  4. [
Show the answer

Answer: D. [

Mixing time in stirred vessel:

  1. [
  2. "
  3. _
  4. t
Show the answer

Answer: A. [

Jet pump (ejector) for solids:

  1. i
  2. H
  3. "
  4. [
Show the answer

Answer: D. [

Hydrocyclone for liquid-liquid separation:

  1. e
  2. "
  3. [
  4. S
Show the answer

Answer: C. [

Disc filter (pressure leaf filter):

  1. R
  2. "
  3. [
  4. o
Show the answer

Answer: C. [

Pressure leaf filter (FUNDA filter):

  1. V
  2. e
  3. [
  4. "
Show the answer

Answer: C. [

Thin film evaporator (wiped film):

  1. [
  2. "
  3. e
  4. M
Show the answer

Answer: A. [

Cavitation in mixers:

  1. a
  2. [
  3. "
  4. G
Show the answer

Answer: B. [

Power number Np in mixing:

  1. [
  2. p
  3. "
  4. N
Show the answer

Answer: A. [

Scale-up of mixing - constant P/V:

  1. C
  2. o
  3. "
  4. [
Show the answer

Answer: D. [

Flow number (pumping number) Nq:

  1. "
  2. N
  3. [
  4. q
Show the answer

Answer: C. [

Dispersion index in mixing:

  1. R
  2. "
  3. a
  4. [
Show the answer

Answer: D. [

High shear mixer (Silverson):

  1. Only for solids
  2. Rotor-stator head creates intense shear for emulsification, dissolution, dispersion in liquids
  3. Gentle mixing
  4. None
Show the answer

Answer: B. Rotor-stator head creates intense shear for emulsification, dissolution, dispersion in liquids

Ribbon blender:

  1. Horizontal trough with helical ribbon agitators
  2. Only for liquids
  3. None
  4. Vertical blender
Show the answer

Answer: A. Horizontal trough with helical ribbon agitators Horizontal trough with helical ribbon agitators - inner and outer ribbons move material in opposite directions

Agitated vessel scale-up:

  1. None
  2. Constant tip speed or power-per-unit-volume
  3. Same impeller size
  4. Same RPM always
Show the answer

Answer: B. Constant tip speed or power-per-unit-volume Constant tip speed or power-per-unit-volume - mixing time and regime preserved

Cavitation in pump:

  1. Only in high-pressure pumps
  2. None
  3. Vapour bubbles form and collapse in pump impeller
  4. Good for pump
Show the answer

Answer: C. Vapour bubbles form and collapse in pump impeller Vapour bubbles form and collapse in pump impeller - damage, noise, reduced performance

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →