IITIAN1997 STUDIO

Distillation, absorption, extraction, drying (Unit Operation-II and III)

JLEE CHE · 149 practice questions with answers

Practise and take a mock test →

Diffusion, distillation, absorption, extraction, drying

Topics: Molecular diffusion (Fick’s law), mass-transfer coefficients; vapour–liquid equilibrium, Raoult’s and Henry’s laws, relative volatility, azeotropes; distillation (flash, simple, steam, fractional), McCabe–Thiele method, reflux ratio, minimum and total reflux; gas absorption and stripping, packed and plate towers, flooding; liquid–liquid extraction, leaching; humidification and cooling towers; drying (rate curve, constant and falling rate periods); crystallisation and adsorption.

Diffusion and vapour–liquid equilibrium

Fick’s law: the molar flux is proportional to the concentration gradient, N = −D dC/dz. Mass-transfer coefficients lump this into N = k ΔC across a film.

For ideal liquid mixtures Raoult’s law gives pᵢ = xᵢPᵢ°; the vapour is richer in the more volatile component. Relative volatility α = (y/x)_A / (y/x)_B = P_A°/P_B° for ideal systems; the larger α, the easier the separation. Azeotropes boil at constant composition and cannot be separated by ordinary distillation.

  • N = −D dC/dz
  • pᵢ = xᵢPᵢ° (Raoult); p = Hx (Henry)
  • α = P_A°/P_B°

Example: At 80 °C, P°(benzene) = 757 and P°(toluene) = 291 mmHg. For x_B = 0.5 find the total pressure and y_B.

  1. P = 0.5 × 757 + 0.5 × 291 = 524 mmHg.
  2. y_B = 378.5/524 = 0.722.

Answer: P = 524 mmHg, y_B ≈ 0.72

Example: Find the relative volatility of benzene to toluene at 80 °C.

  1. α = 757/291.
  2. ≈ 2.6.

Answer: ≈ 2.6

Distillation and the McCabe–Thiele method

McCabe–Thiele assumes constant molar overflow. The rectifying operating line is y = [R/(R + 1)]x + x_D/(R + 1); the q-line through the feed point has slope q/(q − 1) (vertical for saturated liquid feed). Steps between the equilibrium curve and the operating lines count the theoretical stages.

Total reflux gives the minimum number of stages (Fenske): N_min = ln[(x_D/(1 − x_D))((1 − x_B)/x_B)]/ln α. Minimum reflux gives infinite stages; operating reflux is usually 1.2–1.5 times the minimum.

  • Rectifying line slope R/(R + 1), intercept x_D/(R + 1)
  • Saturated liquid feed: q = 1, vertical q-line
  • Fenske: minimum stages at total reflux

Example: With R = 2 and x_D = 0.9, find the slope and intercept of the rectifying line.

  1. Slope = 2/3 ≈ 0.667.
  2. Intercept = 0.9/3 = 0.3.

Answer: y = 0.667x + 0.3

Example: Find N_min for x_D = 0.95, x_B = 0.05 and α = 2.5.

  1. N_min = ln(19 × 19)/ln 2.5 = 5.889/0.916.
  2. ≈ 6.4 stages (including the reboiler).

Answer: ≈ 6.4

Absorption, extraction and drying

Gas absorption dissolves a component of a gas in a liquid (packed or tray towers); stripping is the reverse. Liquid–liquid extraction transfers a solute into a second solvent. Leaching extracts a solute from a solid.

Drying removes moisture: a constant-rate period (surface wet, like evaporation from water) is followed by a falling-rate period below the critical moisture content. Moisture on a dry basis X = water/dry solid; wet basis w = water/total.

  • Absorption: gas → liquid; stripping: liquid → gas
  • Dry basis X = water/dry solid
  • Constant rate, then falling rate

Example: 100 kg of wet solid with 40 % moisture (wet basis) is dried to 10 %. How much water is removed?

  1. Dry solid = 60 kg; final mass = 60/0.9 = 66.7 kg.
  2. Water removed = 100 − 66.7 = 33.3 kg.

Answer: 33.3 kg

Example: Express 40 % moisture (wet basis) on a dry basis.

  1. X = 40 kg water / 60 kg dry solid.
  2. = 0.667 kg/kg.

Answer: 0.667

Diffusion follows Fick’s law J = −D_AB dC/dz. Ideal solutions obey Raoult’s law p_A = x_A P_A^sat; dilute gases dissolve by Henry’s law p_A = H x_A. Relative volatility α = (y_A/x_A)/(y_B/x_B) measures ease of separation by distillation — α = 1 means no separation (an azeotrope). The McCabe–Thiele construction steps between the equilibrium curve and the operating lines to count ideal stages; at total reflux the stages are minimum, and at minimum reflux an infinite number is needed. Absorption needs high pressure and low temperature, stripping the opposite. In drying, the constant-rate period removes surface moisture; below the critical moisture content the rate falls.

  • Rectifying operating line slope = R/(R + 1).
  • q-line: q = 1 saturated liquid (vertical), q = 0 saturated vapour (horizontal).
  • Fenske equation gives minimum stages at total reflux.
  • Steam distillation separates high-boiling, water-immiscible organics below their boiling point.
  • Optimum reflux ≈ 1.2 – 1.5 × minimum reflux.

Key formulas

  • J = −D dC/dz
  • p_A = x_A P_A^sat
  • α = P_A^sat/P_B^sat (ideal)
  • y = Rx/(R + 1) + x_D/(R + 1)

Practice questions

Fick’s first law relates flux to

  1. temperature gradient
  2. concentration gradient
  3. pressure
  4. velocity
Show the answer

Answer: B. concentration gradient J = −D dC/dz.

Separation by distillation is impossible when relative volatility is

  1. > 1
  2. = 1
  3. < 1
  4. ∞
Show the answer

Answer: B. = 1 Azeotrope.

At total reflux the number of plates is

  1. maximum
  2. minimum
  3. infinite
  4. zero
Show the answer

Answer: B. minimum Fenske minimum.

At minimum reflux the number of plates is

  1. minimum
  2. infinite
  3. one
  4. zero
Show the answer

Answer: B. infinite Pinch point.

The slope of the rectifying operating line is

  1. R/(R + 1)
  2. (R + 1)/R
  3. L/V in stripping
  4. 1
Show the answer

Answer: A. R/(R + 1) L/V = R/(R + 1).

Absorption is favoured by

  1. high temperature, low pressure
  2. low temperature, high pressure
  3. high temperature, high pressure
  4. low pressure only
Show the answer

Answer: B. low temperature, high pressure Higher solubility.

For saturated liquid feed, the q-line is

  1. horizontal
  2. vertical
  3. at 45°
  4. inclined negatively
Show the answer

Answer: B. vertical q = 1.

Henry’s law is valid for

  1. concentrated solutions
  2. dilute solutions of gases
  3. solids
  4. azeotropes
Show the answer

Answer: B. dilute solutions of gases Dilute range.

During the constant-rate period of drying

  1. internal diffusion controls
  2. surface moisture evaporates
  3. no moisture is removed
  4. rate increases
Show the answer

Answer: B. surface moisture evaporates Like a free water surface.

Steam distillation is used for

  1. high-boiling, water-immiscible liquids
  2. gases
  3. salts
  4. azeotropes only
Show the answer

Answer: A. high-boiling, water-immiscible liquids Lowers the boiling temperature.

Flooding in a packed tower is caused by

  1. very low gas rate
  2. excessive gas or liquid rate
  3. high temperature
  4. low pressure
Show the answer

Answer: B. excessive gas or liquid rate Liquid held up by gas.

Leaching is

  1. liquid–liquid extraction
  2. solid–liquid extraction
  3. gas absorption
  4. drying
Show the answer

Answer: B. solid–liquid extraction Solute dissolved from a solid.

The unit of volumetric diffusivity is

  1. cm²/sec
  2. cm/sec
  3. cm³/sec
  4. cm²/sec²
Show the answer

Answer: A. cm²/sec

In a binary gas mixture, diffusivity varies with absolute temperature roughly as

  1. D ∝ T
  2. D ∝ T^0.5
  3. D ∝ T^1.5
  4. D ∝ T²
Show the answer

Answer: C. D ∝ T^1.5

In a binary gas mixture, diffusivity varies with pressure as

  1. D ∝ P^0.5
  2. D ∝ 1/P^0.5
  3. D ∝ 1/P
  4. D ∝ 1/P^1.5
Show the answer

Answer: C. D ∝ 1/P

Molecular diffusion is driven by the

  1. transfer of molecules from low concentration to high concentration region.
  2. thermal energy of the molecules.
  3. activation energy of the molecules.
  4. potential energy of the molecules.
Show the answer

Answer: B. thermal energy of the molecules.

Which statement about diffusivity is correct?

  1. Diffusivity decreases with increase in temperature.
  2. Diffusivity increases with increase in molecular weight.
  3. Diffusivity increases with the size of the individual molecule.
  4. none of these.
Show the answer

Answer: D. none of these.

A mass-transfer coefficient is defined by

  1. Flux = Co-efficient/concentration difference.
  2. Co-efficient = Flux/concentration difference.
  3. Flux = concentration difference/co-efficient.
  4. none of these.
Show the answer

Answer: B. Co-efficient = Flux/concentration difference.

According to film theory, the mass-transfer coefficient K varies with diffusivity D as

  1. K ∝ D
  2. K ∝ √D
  3. K ∝ D^1.5
  4. K ∝ D²
Show the answer

Answer: A. K ∝ D

According to penetration theory, the average mass-transfer coefficient varies with diffusivity as

  1. K ∝ D
  2. K ∝ √D
  3. K ∝ D^1.5
  4. K ∝ D²
Show the answer

Answer: B. K ∝ √D

The mass-transfer counterpart of the Prandtl number is the ____ number.

  1. Schmidt
  2. Sherwood
  3. Peclet
  4. Stanton
Show the answer

Answer: A. Schmidt

The Schmidt number is

  1. μ/(ρ·D_AB)
  2. Re.Pe
  3. Sh × Pe
  4. Re/Pe
Show the answer

Answer: A. μ/(ρ·D_AB)

Physically, the Schmidt number is the ratio of

  1. thermal diffusivity/mass diffusivity.
  2. thermal diffusivity/momentum diffusivity.
  3. momentum diffusivity/mass diffusivity.
  4. mass diffusivity/thermal diffusivity.
Show the answer

Answer: C. momentum diffusivity/mass diffusivity.

The mass-transfer counterpart of the Nusselt number is the ____ number.

  1. Sherwood
  2. Schmidt
  3. Peclet
  4. Stanton
Show the answer

Answer: A. Sherwood

The liquid-phase mass-transfer coefficient is

  1. affected more by temperature than that for gases.
  2. affected much less by temperature than that for gases.
  3. not affected by the temperature.
  4. none of these.
Show the answer

Answer: A. affected more by temperature than that for gases.

To absorb a sparingly soluble gas efficiently, one should raise the

  1. gas side coefficient should be increased.
  2. liquid side coefficient should be increased.
  3. gas side coefficient should be decreased.
  4. liquid side coefficient should be decreased.
Show the answer

Answer: B. liquid side coefficient should be increased.

To bring a highly soluble gas into contact with a liquid, one may

  1. bubble the gas through liquid.
  2. spray the liquid on gas stream.
  3. either (a) or (b) would suffice.
  4. none of these.
Show the answer

Answer: C. either (a) or (b) would suffice.

A wetted-wall tower experiment is used to find the

  1. molal diffusivity.
  2. volumetric co-efficient.
  3. mass transfer co-efficient.
  4. none of these.
Show the answer

Answer: C. mass transfer co-efficient.

The Lewis number is

  1. Sc/Pr
  2. Pr × St
  3. Sh × Pr
  4. St × Sh
Show the answer

Answer: A. Sc/Pr

Compared with dumped packing, stacked packing

  1. provides poorer contact between the fluids.
  2. gives lower pressure drop.
  3. both (a) and (b).
  4. gives higher pressure drop.
Show the answer

Answer: C. both (a) and (b).

Channelling is most severe in towers with

  1. in towers packed with stacked packing.
  2. in towers packed randomly with crushed solids.
  3. in dumped packing of regnlar units.
  4. at very high liquid flow rate.
Show the answer

Answer: A. in towers packed with stacked packing.

Flooding causes

  1. high tray efficiency
  2. low tray efficiency
  3. high gas velocity
  4. good contact between the fluids
Show the answer

Answer: B. low tray efficiency

A packed tower is normally operated at about ____ the flooding velocity.

  1. half
  2. twice
  3. equal to
  4. more than
Show the answer

Answer: A. half

At the same gas rate, the pressure drop through irrigated packing compared with dry packing is

  1. is greater than
  2. is lower than
  3. is same as
  4. cannot be predicted as data are insufficient
Show the answer

Answer: A. is greater than

Carbon Berl saddles cannot be used in

  1. alkalis
  2. SO₂
  3. H₂SO₄
  4. oxidising atmosphere
Show the answer

Answer: D. oxidising atmosphere

Flooding in a column is associated with

  1. high pressure drop
  2. low pressure drop
  3. low velocity of the liquid
  4. high temperature
Show the answer

Answer: A. high pressure drop

An absorber’s operating line is curved when plotted in

  1. mole fractions
  2. mole ratios
  3. partial pressure
  4. mass fractions
Show the answer

Answer: A. mole fractions

For an absorber, the operating line

  1. line always lies above the equilibrium curve.
  2. line always lies below the equilibrium curve.
  3. line can be either above or below the equilibrium curve.
  4. velocity is more than the loading velocity.
Show the answer

Answer: A. line always lies above the equilibrium curve.

Both the equilibrium and operating lines of an absorber are straight for

  1. concentrated solution and non isothermal operation.
  2. dilute solution and non isothermal operation.
  3. dilute solution and isothermal operation.
  4. concentrated solution and isothermal operation.
Show the answer

Answer: C. dilute solution and isothermal operation.

For a stripper (desorber), the operating line

  1. operating line always lies above the equilibrium curve.
  2. operating line always lies below the equilibrium curve.
  3. temperature remains unaffected.
  4. temperature always increases.
Show the answer

Answer: B. operating line always lies below the equilibrium curve.

The minimum liquid rate in an absorber corresponds to an operating line that

  1. of slope = 1
  2. of slope = 0.1
  3. tangential to the equilibrium curve
  4. none of these
Show the answer

Answer: C. tangential to the equilibrium curve

With S₁ the slope of the operating line and S₂ that of the equilibrium curve, the absorption factor is

  1. S₂/S₁
  2. S₁/S₂
  3. S₁ - S₂
  4. S₁ × S₂
Show the answer

Answer: B. S₁/S₂

With G the inert gas rate and L the non-volatile solvent rate, the absorber operating line has slope

  1. L/G
  2. G/L
  3. always < 1
  4. none of these
Show the answer

Answer: A. L/G

Porcelain Raschig rings cannot be used for concentrated

  1. hydrochloric acid
  2. nitric acid
  3. alkalis
  4. sulphuric acid
Show the answer

Answer: C. alkalis

A high pressure drop in an absorber leads to

  1. increased efficiency.
  2. decreased efficiency.
  3. high operating cost.
  4. better gas liquid contact.
Show the answer

Answer: C. high operating cost.

Which of these is an undesirable property in an absorption solvent?

  1. Low vapour pressure
  2. Low velocity
  3. Low freezing point
  4. None of these
Show the answer

Answer: D. None of these

A good absorption solvent should have which properties? (I) high viscosity (II) low viscosity (III) high vapour pressure (IV) low vapour pressure (V) high gas solubility (VI) high freezing point (VII) low freezing point

  1. II, IV, V, VII
  2. I, IV, V, VI
  3. II, IV, V, VI
  4. I, III, V, VII
Show the answer

Answer: A. II, IV, V, VII

When gas and liquid flow co-currently in an absorber, the operating line slope is

  1. -ve
  2. +ve
  3. 1
  4. -1
Show the answer

Answer: A. -ve

In an absorber, HETP does NOT vary with the

  1. flow rate of liquid
  2. flow rate of gas
  3. type and size of packing
  4. none of these
Show the answer

Answer: D. none of these

Which property is undesirable in a tower packing?

  1. Large surface per unit volume.
  2. Large free cross-section.
  3. Low weight per unit volume.
  4. Large weight of liquid retained.
Show the answer

Answer: D. Large weight of liquid retained.

Very tall packed towers are split into several beds mainly to

  1. reduce the overall pressure drop
  2. avoid channelling
  3. reduce liquid hold-up
  4. avoid flooding
Show the answer

Answer: B. avoid channelling

If the solvent rate to an absorber is reduced (same system), the tower height needed will

  1. increase
  2. decrease
  3. remain unaffected
  4. decrease or increase; depends on the type of liquid
Show the answer

Answer: A. increase

HETP equals HTU only when the operating and equilibrium lines

  1. lies below the equilibrium line.
  2. lies above the equilibrium line.
  3. and equilibrium lines are parallel.
  4. is far from the equilibrium line.
Show the answer

Answer: C. and equilibrium lines are parallel.

The desirable value of the absorption factor is

  1. 1
  2. <1
  3. >1
  4. 0.5
Show the answer

Answer: C. >1

Co-current absorbers are used mainly when the gas is

  1. sparingly soluble
  2. highly soluble
  3. a pure substance
  4. a mixture
Show the answer

Answer: B. highly soluble

Humidification involves mass transfer between a pure liquid and a gas that is

  1. insoluble in the liquid
  2. soluble in the liquid
  3. non-ideal in nature
  4. at a fixed temperature
Show the answer

Answer: A. insoluble in the liquid

At fixed total pressure, humidity depends only on the

  1. partial pressure of vapour in the mixture.
  2. heat capacity of the vapour.
  3. density of the vapour.
  4. none of these.
Show the answer

Answer: A. partial pressure of vapour in the mixture.

In a saturated gas,

  1. vapour is in equilibrium with the liquid at the gas temperature.
  2. vapour is in equilibrium with the liquid at the room temperature.
  3. partial pressure of vapour equals the vapour pressure of the liquid at room temperature.
  4. none of these.
Show the answer

Answer: A. vapour is in equilibrium with the liquid at the gas temperature.

Relative humidity is the ratio of the vapour’s partial pressure to the

  1. partial pressure of the vapour to the vapour pressure of the liquid at room temperature.
  2. partial pressure of the vapour to the vapour pressure of the liquid at gas temperature.
  3. actual humidity to saturation humidity.
  4. none of these
Show the answer

Answer: B. partial pressure of the vapour to the vapour pressure of the liquid at gas temperature.

Percentage humidity and relative humidity are equal at

  1. zero
  2. hundred
  3. both zero and hundred
  4. none of these
Show the answer

Answer: C. both zero and hundred

The heat needed to raise 1 lb of gas with its vapour by 1 °F is the

  1. latent heat
  2. humid heat
  3. specific heat
  4. sensible heat
Show the answer

Answer: B. humid heat

Humid volume is the volume in m³ of 1 kg of dry gas together with its vapour at 1 atm and the

  1. vapour laden gas at 1 atm. and room temperature.
  2. gas plus its accompanying vapour at 1 atm. and room temperature.
  3. gas plus its accompanying vapour at 1 atm. and gas temperature.
  4. vapour laden gas at 1 atm. and gas temperature.
Show the answer

Answer: C. gas plus its accompanying vapour at 1 atm. and gas temperature.

The temperature to which a gas–vapour mixture must be cooled (at constant humidity) to become saturated is the

  1. dew point
  2. wet bulb
  3. dry bulb
  4. none of these
Show the answer

Answer: A. dew point

For a saturated gas, the dew point equals the

  1. gas
  2. room
  3. wet bulb
  4. none of these
Show the answer

Answer: A. gas

The steady temperature reached by a small amount of liquid evaporating into a large amount of unsaturated gas is the

  1. dry-bulb
  2. wet-bulb
  3. dew point
  4. adiabatic saturation
Show the answer

Answer: B. wet-bulb

For unsaturated air, the dry-bulb temperature is always ____ the wet-bulb temperature.

  1. less than
  2. more than
  3. equal to
  4. none of these
Show the answer

Answer: B. more than

When air temperature and humidity are low, a ____ draught cooling tower is often used.

  1. natural
  2. forced
  3. induced
  4. none of these
Show the answer

Answer: A. natural

Adiabatic humidification–cooling with recirculating water is usually done in a

  1. natural draft cooling tower
  2. induced draft cooling tower
  3. spray chamber
  4. none of these
Show the answer

Answer: C. spray chamber

The most efficient type of cooling tower is the

  1. induced draft
  2. forced draft
  3. natural draft
  4. atmospheric
Show the answer

Answer: A. induced draft

In distillation of a multicomponent mixture, the overhead product can contain

  1. only one component
  2. two components
  3. any number of components
  4. only saturated liquid
Show the answer

Answer: C. any number of components

A boiling-point (T–x–y) diagram

  1. not affected by pressure.
  2. affected by pressure.
  3. a plot of temperature vs. liquid composition.
  4. a plot of temperature vs. vapour composition.
Show the answer

Answer: B. affected by pressure.

Raoult’s law applies to

  1. ideal solutions
  2. real solutions
  3. mixture of water and alcohol
  4. non ideal gases
Show the answer

Answer: A. ideal solutions

In a dilute solution, Raoult’s law applies to the

  1. all liquid solutions.
  2. non ideal solution only.
  3. non volatile solute.
  4. solvents.
Show the answer

Answer: D. solvents.

Henry’s law states that the

  1. partial pressure of a component over a solution is proportional to its mole fraction in the liquid.
  2. partial pressure of a component over a solution is proportional to the mole fraction in the vapour.
  3. vapour pressure is equal to the product of the mole fraction and total pressure.
  4. partial pressure is equal to the product of the mole fraction and total pressure.
Show the answer

Answer: A. partial pressure of a component over a solution is proportional to its mole fraction in the liquid.

Flash (equilibrium) distillation is

  1. same as differential distillation.
  2. used for multicomponent systems like crude refining.
  3. same as simple distillation.
  4. most useful for handling binary systems.
Show the answer

Answer: B. used for multicomponent systems like crude refining.

For a binary system obeying Raoult’s and Dalton’s laws, relative volatility is the ratio of

  1. vapour pressure of component A to that of component B.
  2. vapour pressure of component A to the total pressure.
  3. vapour pressure of component A to the partial pressure of A.
  4. partial pressure of component A to the total pressure.
Show the answer

Answer: A. vapour pressure of component A to that of component B.

Relative volatility changes little with

  1. temperature
  2. vapour pressure of either component
  3. total pressure
  4. none of these
Show the answer

Answer: C. total pressure

Separation of a binary mixture by distillation is easy when relative volatility is

  1. 1
  2. >1
  3. <1
  4. 0.5
Show the answer

Answer: B. >1

A positive deviation from Raoult’s law means the total pressure is

  1. greater than that computed for ideality.
  2. less than that computed for ideality.
  3. less than the sum of the vapour pressure of the components.
  4. none of these.
Show the answer

Answer: A. greater than that computed for ideality.

For an azeotropic mixture, the equilibrium vapour composition is

  1. more than liquid composition.
  2. less than liquid composition.
  3. same as liquid composition.
  4. independent of pressure.
Show the answer

Answer: C. same as liquid composition.

In batch distillation at constant reflux, the overhead composition with time

  1. increases
  2. decreases
  3. does not vary
  4. may increase or decrease, depends on the system.
Show the answer

Answer: B. decreases

In the rectifying section of a continuous column,

  1. vapour is enriched with low boilers.
  2. vapour is enriched with high boilers.
  3. liquid is stripped of high boilers.
  4. none of these.
Show the answer

Answer: A. vapour is enriched with low boilers.

For a binary mixture of low relative volatility, pure products need

  1. low reflux ratio
  2. less number of trays
  3. small cross-section column
  4. high reflux ratio
Show the answer

Answer: D. high reflux ratio

Azeotropic distillation is used to separate

  1. constant boiling mixture.
  2. high boiling mixture.
  3. mixture with very high relative volatility.
  4. heat sensitive materials.
Show the answer

Answer: A. constant boiling mixture.

For a binary mixture of low relative volatility,

  1. use steam distillation.
  2. use molecular distillation.
  3. use high pressure distillation.
  4. an azeotrope may be formed during distillation.
Show the answer

Answer: D. an azeotrope may be formed during distillation.

The entrainer used in azeotropic distillation should

  1. form a low boiling azeotrope with one of the constituents of the mixture.
  2. form a new azeotrope of low relative volatility with one of the constituents of the mixture.
  3. have high latent heat of vaporisation.
  4. have high viscosity to provide high tray efficiency.
Show the answer

Answer: A. form a low boiling azeotrope with one of the constituents of the mixture.

Ethanol is dehydrated by ____ distillation.

  1. extractive
  2. azeotropic
  3. steam
  4. molecular
Show the answer

Answer: B. azeotropic

Rose oil is recovered from petals by ____ distillation.

  1. high pressure
  2. low pressure
  3. extractive
  4. steam
Show the answer

Answer: D. steam

In extractive distillation, the solvent is

  1. added to alter the relative volatility of the mixture.
  2. of high volatility.
  3. present in overhead stream.
  4. of high viscosity to give high tray efficiency.
Show the answer

Answer: A. added to alter the relative volatility of the mixture.

Molecular distillation is used

  1. high temperature distillation
  2. for heat sensitive materials
  3. very low pressure distillation
  4. both (b) and (c)
Show the answer

Answer: D. both (b) and (c)

In steam distillation,

  1. temperature is 100°C.
  2. temperature is more than 100°C.
  3. product must be immiscible with water,
  4. temperature is higher than the boiling point of either component.
Show the answer

Answer: C. product must be immiscible with water,

Steam distillation is used to separate

  1. azeotropes.
  2. high boiling substances from nonvolatile impurities.
  3. heat sensitive materials.
  4. mixtures of low relative volatility.
Show the answer

Answer: B. high boiling substances from nonvolatile impurities.

If more steam is used in steam distillation, the distillation temperature

  1. increases
  2. decreases
  3. remains unchanged
  4. depends on relative volatility
Show the answer

Answer: C. remains unchanged

A high pressure at the bottom of a column handling heat-sensitive material causes

  1. thermal decomposition of bottoms.
  2. increased relative volatility.
  3. erosion of the tower.
  4. very efficient operation.
Show the answer

Answer: A. thermal decomposition of bottoms.

Components with widely different boiling points can be separated by ____ distillation.

  1. molecular
  2. extractive
  3. steam
  4. simple
Show the answer

Answer: D. simple

Which method assumes constant molal overflow and vaporisation?

  1. McCabe-Thiele method
  2. Ponchan-Savarit method
  3. Enthalpy concentration method
  4. Plate absorption column
Show the answer

Answer: A. McCabe-Thiele method

The McCabe–Thiele method

  1. uses molal units for material and energy balance.
  2. uses weight fractions to express liquid and vapour composition.
  3. can use any type of units.
  4. is more accurate than Ponchan-Savarit method.
Show the answer

Answer: A. uses molal units for material and energy balance.

In the stripping section of a continuous column,

  1. liquid is stripped of high boiler.
  2. liquid is enriched with high boiler.
  3. vapour is stripped of low boiler.
  4. none of these.
Show the answer

Answer: B. liquid is enriched with high boiler.

For the same diameter, which column gives the lowest pressure drop per unit height?

  1. Bubble cap column
  2. Sieve plate column
  3. Packed column (stacked)
  4. Randomly packed column
Show the answer

Answer: C. Packed column (stacked)

Reflux is 100 mol/h and overhead product 50 mol/h. The reflux ratio is

  1. 2
  2. 0.5
  3. 50
  4. 150
Show the answer

Answer: A. 2

If f is the fraction of feed that is vapour, the feed (q) line in McCabe–Thiele has slope

  1. (1-f)/f
  2. (f-1)/f
  3. -1/f
  4. -f/(1-f)
Show the answer

Answer: B. (f-1)/f

With f defined as above, a feed at its dew point has

  1. f = 1
  2. f < 1
  3. f > 1
  4. 0 < f < 1
Show the answer

Answer: A. f = 1

For a saturated-liquid feed, the slope of the feed line is

  1. zero
  2. unity
  3. infinity
  4. none of these
Show the answer

Answer: C. infinity

Which equipment gives the largest contact surface for a liquid–vapour system?

  1. Packed tower
  2. Bubble cap plate column
  3. Seive plate column
  4. Wetted wall column
Show the answer

Answer: A. Packed tower

At total reflux, the reflux ratio is

  1. Zero
  2. Infinity
  3. Unity
  4. Data insufficient
Show the answer

Answer: B. Infinity

As reflux ratio increases, the slope of the rectifying operating line

  1. increases
  2. decreases
  3. remains constant
  4. data insufficient, cannot be predicted
Show the answer

Answer: A. increases

In McCabe–Thiele, at infinite reflux ratio,

  1. the number of plates is maximum.
  2. the overhead product is maximum.
  3. both operating lines coincide with the diagonal.
  4. none of these.
Show the answer

Answer: C. both operating lines coincide with the diagonal.

The Fenske equation gives the

  1. maximum number of ideal plates.
  2. height of the distillation column.
  3. minimum number of theoretical plates.
  4. optimum reflux ratio.
Show the answer

Answer: C. minimum number of theoretical plates.

At minimum reflux for a given separation, the number of plates is

  1. number of plates is zero.
  2. number of plates is infinity.
  3. minimum number of the theoretical plates is required.
  4. separation is most efficient.
Show the answer

Answer: B. number of plates is infinity.

For the ethanol–water system, the minimum reflux ratio is found from

  1. is computed from the slope of the upper operating line that is tangent to the equilibrium curve.
  2. is computed from the intercept of the operating line.
  3. cannot be computed.
  4. is the optimum reflux ratio.
Show the answer

Answer: A. is computed from the slope of the upper operating line that is tangent to the equilibrium curve.

As the reflux ratio decreases,

  1. separation becomes more efficient.
  2. number of plates decreases.
  3. column diameter increases.
  4. none of these.
Show the answer

Answer: D. none of these.

The absorption-factor (Kremser) method gives ideal stages directly when

  1. operating line lies above the equilibrium line.
  2. operating line lies below the equilibrium line.
  3. both operating and equilibrium lines are parallel.
  4. pressure drop in the column is very high.
Show the answer

Answer: C. both operating and equilibrium lines are parallel.

The Ponchon–Savarit method is based on

  1. enthalpy balance only.
  2. material balance only.
  3. both enthalpy and material balances.
  4. the assumption of constant molal overflow.
Show the answer

Answer: C. both enthalpy and material balances.

A reboiler counts as one theoretical plate because

  1. of the assumption that vapour and liquid leaving the reboiler are in equilibrium.
  2. vapour is recycled to the column.
  3. reboiler itself contains one plate.
  4. none of these.
Show the answer

Answer: A. of the assumption that vapour and liquid leaving the reboiler are in equilibrium.

High tray efficiency needs

  1. interfacial surface between liquid and gas phase should be large.
  2. time of contact between the two phases should be less.
  3. gas velocity should be very low.
  4. liquid entrainment should be severe.
Show the answer

Answer: A. interfacial surface between liquid and gas phase should be large.

The non-volatile film-forming constituent of a paint is the

  1. Thinner
  2. Dryer
  3. Drying oil
  4. none of these
Show the answer

Answer: C. Drying oil

When dry-bulb and wet-bulb temperatures of moist air are equal, the

  1. partial pressure of water vapour is less than the total pressure.
  2. humidity is < 100% & dew point temperature of air has not reached.
  3. dew point temperature of air has not reached & air is not saturated fully.
  4. air is fully saturated.
Show the answer

Answer: D. air is fully saturated.

As relative humidity falls, the dew point becomes ____ the wet-bulb temperature.

  1. less than the wet bulb temperature
  2. more than the wet bulb temperature
  3. more than the dry bulb temperature
  4. equal to wet bulb temperature
Show the answer

Answer: A. less than the wet bulb temperature

Which of these is dimensionless (kg per kg)?

  1. heat
  2. humidity
  3. weight
  4. none of these
Show the answer

Answer: B. humidity

Desert coolers work poorly in the rainy season because of

  1. low humidity
  2. low temperature
  3. high humidity
  4. sunny weather
Show the answer

Answer: C. high humidity

For human comfort, the air should be at 22–27 °C with relative humidity of about ____ %.

  1. 5 to 10
  2. 15 to 25
  3. 45 to 50
  4. 75 to 80
Show the answer

Answer: C. 45 to 50

During adiabatic cooling of moist air, which quantity stays constant?

  1. Wet bulb temperature
  2. Dry bulb temperature
  3. Relative humidity
  4. Specific humidity
Show the answer

Answer: A. Wet bulb temperature

Which temperature is NOT read directly on a psychrometer?

  1. dew point
  2. dry bulb
  3. wet bulb
  4. none of these
Show the answer

Answer: A. dew point

A flare stack in a plant is used for

  1. venting off (after burning) the excess inflammable/toxic gases at high pressure.
  2. absorbing the pollutant gases from the furnace exhaust.
  3. cooling of furnace exhaust gases.
  4. none of these.
Show the answer

Answer: A. venting off (after burning) the excess inflammable/toxic gases at high pressure.

Dry-bulb and wet-bulb thermometers read the same only at ____ % relative humidity.

  1. 0
  2. 100
  3. 50
  4. none of these
Show the answer

Answer: B. 100

Distillation column tray types:

  1. None
  2. Only sieve
  3. Only bubble cap
  4. Sieve tray, bubble cap tray, valve tray
Show the answer

Answer: D. Sieve tray, bubble cap tray, valve tray Sieve tray, bubble cap tray, valve tray - different efficiency and capacity

Tray efficiency (Murphree):

  1. 100% always
  2. None
  3. EMV =/
  4. Only for bubble cap
Show the answer

Answer: C. EMV =/ EMV = (yn − yn-1)/(y*n − yn-1) - actual vs theoretical separation on tray

HETP (Height Equivalent to a Theoretical Plate):

  1. Height of packing giving separation equal to one theoretical stage
  2. Tray spacing
  3. None
  4. Height of column
Show the answer

Answer: A. Height of packing giving separation equal to one theoretical stage

Flooding in distillation column:

  1. Low vapour rate
  2. Optimal operation
  3. Excessive liquid or vapour velocity causing liquid to carry over or back-flow
  4. None
Show the answer

Answer: C. Excessive liquid or vapour velocity causing liquid to carry over or back-flow Excessive liquid or vapour velocity causing liquid to carry over or back-flow - loss of separation

Downcomer backup:

  1. None
  2. Pressure limit
  3. Vapour velocity limit
  4. Liquid height in downcomer must not exceed tray spacing
Show the answer

Answer: D. Liquid height in downcomer must not exceed tray spacing Liquid height in downcomer must not exceed tray spacing - limits liquid rate

McCabe-Thiele method:

  1. Ternary system
  2. None
  3. Numerical only
  4. Graphical method for binary distillation using operating lines and equilibrium curve
Show the answer

Answer: D. Graphical method for binary distillation using operating lines and equilibrium curve

Packed column advantages over trays:

  1. None
  2. Always cheaper
  3. Always higher capacity
  4. Lower pressure drop, good for corrosive/foaming systems, suitable for vacuum operations
Show the answer

Answer: D. Lower pressure drop, good for corrosive/foaming systems, suitable for vacuum operations

Packing factor (Fp):

  1. Thermal factor
  2. Characterises packing hydraulics; used in flooding calculations
  3. None
  4. Efficiency factor
Show the answer

Answer: B. Characterises packing hydraulics; used in flooding calculations Characterises packing hydraulics (higher Fp = more pressure drop); used in flooding calculations

Thermosiphon reboiler driving force:

  1. Gravity head only
  2. Density difference between liquid in reboiler and column bottom
  3. None
  4. Pump driven
Show the answer

Answer: B. Density difference between liquid in reboiler and column bottom Density difference between liquid in reboiler and column bottom - natural circulation

Wind load on tall column:

  1. Not required in India
  2. None
  3. ASCE 7 or IS codes
  4. Only earthquake
Show the answer

Answer: C. ASCE 7 or IS codes ASCE 7 or IS codes - depends on column height, diameter, wind speed, site category

Seismic design of vessels:

  1. None
  2. UBC or IS 1893 seismic zone factor
  3. Only for buildings
  4. Not required
Show the answer

Answer: B. UBC or IS 1893 seismic zone factor UBC or IS 1893 seismic zone factor - especially critical for tall columns and heavy vessels

Column vibration (wind-induced):

  1. Not a concern
  2. Only for bridges
  3. None
  4. Vortex shedding can cause resonance if natural frequency = shedding frequency
Show the answer

Answer: D. Vortex shedding can cause resonance if natural frequency = shedding frequency Vortex shedding can cause resonance if natural frequency = shedding frequency - add spoilers or dampers

Distillation column internals - structured packing HETP:

  1. M
  2. "
  3. [
  4. e
Show the answer

Answer: C. [

Column flooding correlation - Fair:

  1. o
  2. [
  3. "
  4. S
Show the answer

Answer: B. [

Downcomer backup in distillation:

  1. "
  2. L
  3. [
  4. i
Show the answer

Answer: C. [

Weeping in distillation trays:

  1. L
  2. i
  3. "
  4. [
Show the answer

Answer: D. [

Entrainment in distillation:

  1. [
  2. i
  3. "
  4. L
Show the answer

Answer: A. [

Packed column pressure drop:

  1. L
  2. o
  3. "
  4. [
Show the answer

Answer: D. [

Liquid distribution in packed columns:

  1. [
  2. D
  3. "
  4. i
Show the answer

Answer: A. [

Azeotrope in distillation:

  1. i
  2. "
  3. M
  4. [
Show the answer

Answer: D. [

Extractive distillation:

  1. H
  2. e
  3. "
  4. [
Show the answer

Answer: D. [

Pressure swing distillation:

  1. s
  2. [
  3. U
  4. "
Show the answer

Answer: B. [

Column tray efficiency (Murphree):

  1. E
  2. [
  3. "
  4. M
Show the answer

Answer: B. [

Feed tray location (optimal):

  1. "
  2. q
  3. -
  4. [
Show the answer

Answer: D. [

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →