IITIAN1997 STUDIO

Instrumentation and automatic process control (Ch-501, Ch-601)

JLEE CHE · 296 practice questions with answers

Practise and take a mock test →

Measurement and control of process variables

Topics: Temperature (thermocouples, RTD, thermistor, pyrometers), pressure (manometers, Bourdon gauge, diaphragm), flow and level measurement, static and dynamic characteristics; first-order systems and time constant; controllers (on–off, P, PI, PID), offset, feedback and feed-forward control, control valves.

Measuring temperature and pressure

Thermocouples produce a voltage from two dissimilar metals (Seebeck effect); types K and J are common. Resistance thermometers (RTDs, e.g. Pt100) follow R = R₀(1 + αT) with α ≈ 0.00385/°C for platinum. Thermistors are very sensitive but non-linear. Pyrometers measure hot bodies by their radiation.

Pressure: manometers for low pressures, Bourdon tubes for gauges, diaphragms and strain-gauge transmitters. Absolute pressure = gauge pressure + atmospheric pressure.

  • RTD: R = R₀(1 + αT)
  • Thermocouple: Seebeck voltage
  • p_abs = p_gauge + p_atm

Example: A Pt100 RTD (α = 0.00385/°C) is at 100 °C. Find its resistance.

  1. R = 100(1 + 0.00385 × 100).
  2. = 138.5 Ω.

Answer: 138.5 Ω

Example: A gauge reads 2 bar. Find the absolute pressure.

  1. p_abs = 2 + 1.013.
  2. ≈ 3.01 bar.

Answer: ≈ 3.01 bar (abs)

Flow and level measurement

Head-type flow meters (orifice, venturi) give Q ∝ √Δp, so a fourfold rise in differential pressure means twice the flow. Magnetic meters suit conductive liquids; rotameters are simple variable-area meters. Level: sight glass, float, differential pressure (Δp = ρgh), ultrasonic and radar.

  • Q ∝ √Δp
  • DP level: h = Δp/ρg
  • Magnetic meter needs a conductive liquid

Example: An orifice’s differential pressure rises from 4 to 16 kPa. By what factor has the flow changed?

  1. Q ∝ √Δp, so the ratio is √(16/4).
  2. = 2: the flow has doubled.

Answer: Doubled

Example: A water tank is 2 m deep. What does a DP level transmitter at the bottom read?

  1. Δp = ρgh = 1000 × 9.81 × 2.
  2. ≈ 19.6 kPa.

Answer: ≈ 19.6 kPa

Process dynamics and control

A first-order system responds to a step by reaching 63.2 % of the final change after one time constant τ, 95 % after 3τ and 98 % after 4τ. Controllers: on–off (simple, cycles), proportional (leaves an offset), PI (integral removes offset), PID (derivative adds anticipation). Proportional band PB = 100/Kc %.

Feedback control corrects after an error appears; feed-forward measures a disturbance and acts before it affects the output. Control valves are air-to-open (fail closed) or air-to-close (fail open), chosen for safety.

  • 63.2 % at τ; 95 % at 3τ
  • P leaves offset; I removes it
  • PB = 100/Kc %

Example: A thermometer with τ = 5 s is plunged into hot water. What fraction of the change does it show after 15 s?

  1. 15 s = 3τ.
  2. 1 − e⁻³ ≈ 0.95 = 95 %.

Answer: 95 %

Example: A proportional controller has a proportional band of 50 %. Find its gain.

  1. Kc = 100/PB.
  2. = 100/50 = 2.

Answer: 2

A thermocouple produces an EMF from the junction of two metals (Seebeck effect); an RTD (platinum) changes resistance nearly linearly with temperature; a thermistor has a large negative coefficient; radiation pyrometers measure very hot bodies without contact. A Bourdon tube straightens under pressure. A first-order instrument reaches 63.2% of a step change in one time constant τ. Proportional control leaves a steady-state offset; integral action removes the offset; derivative action anticipates changes and improves stability. A fail-safe valve (air-to-open or air-to-close) is chosen so the plant is safe on air failure.

  • Thermocouple types: J (iron–constantan), K (chromel–alumel), R/S (Pt–Rh) for high temperatures.
  • Accuracy: closeness to the true value; precision: repeatability.
  • Dead time is a pure delay in the response.
  • Proportional band = 100/K_c (%).
  • Cascade control uses a secondary loop inside the primary.

Key formulas

  • y(t) = KA(1 − e^(−t/τ))
  • PB = 100/K_c
  • u = K_c(e + (1/τᵢ)∫e dt + τ_d de/dt)

Practice questions

A thermocouple works on the

  1. Peltier effect
  2. Seebeck effect
  3. Hall effect
  4. Joule effect
Show the answer

Answer: B. Seebeck effect Thermo-EMF.

A first-order system reaches what fraction of a step change in one time constant?

  1. 50%
  2. 63.2%
  3. 86.5%
  4. 100%
Show the answer

Answer: B. 63.2% 1 − e⁻¹.

Offset is removed by

  1. proportional action
  2. integral action
  3. derivative action
  4. on–off control
Show the answer

Answer: B. integral action Reset action.

Which sensor has a large negative temperature coefficient?

  1. RTD
  2. thermistor
  3. thermocouple
  4. bimetal
Show the answer

Answer: B. thermistor Semiconductor.

Very high furnace temperatures are measured with a

  1. mercury thermometer
  2. radiation pyrometer
  3. RTD
  4. bimetallic strip
Show the answer

Answer: B. radiation pyrometer Non-contact.

A Bourdon tube measures

  1. flow
  2. pressure
  3. level
  4. temperature
Show the answer

Answer: B. pressure Pressure gauge.

Derivative action responds to the

  1. error
  2. integral of error
  3. rate of change of error
  4. set point only
Show the answer

Answer: C. rate of change of error Anticipatory.

Proportional band of a controller with gain 4 is

  1. 4%
  2. 25%
  3. 40%
  4. 400%
Show the answer

Answer: B. 25% 100/4.

Repeatability of readings is called

  1. accuracy
  2. precision
  3. sensitivity
  4. resolution
Show the answer

Answer: B. precision Precision.

Feed-forward control acts on

  1. the measured disturbance
  2. the controlled variable
  3. the offset
  4. noise
Show the answer

Answer: A. the measured disturbance Before the error appears.

Which material is NOT used in thermocouples?

  1. Alumel
  2. Rhodium
  3. Constantan
  4. Duralumin
Show the answer

Answer: D. Duralumin

The Laplace transform of sin t is

  1. 1/(s²+1)
  2. s/(1+s²)
  3. 1/(s²-1)
  4. s/(s²-1)
Show the answer

Answer: A. 1/(s²+1)

The transfer function of a first-order system is

  1. 1/(Ts+1)
  2. 1/Ts
  3. s/(Ts+1)
  4. none of these
Show the answer

Answer: A. 1/(Ts+1)

Which of these is a first-order system?

  1. Damped vibrator.
  2. Mercury in glass thermometer kept in boiling water.
  3. Interacting system of two tanks in series.
  4. Non-interacting system of two tanks in series.
Show the answer

Answer: B. Mercury in glass thermometer kept in boiling water.

The response of a system to a sinusoidal input is its ____ response.

  1. impluse
  2. unit step
  3. frequency
  4. none of these
Show the answer

Answer: C. frequency

For a first-order system under sinusoidal forcing, the amplitude ratio (output/input) is

  1. 1
  2. >1
  3. <1
  4. none of these
Show the answer

Answer: C. <1

The phase lag of a first-order system under sinusoidal forcing lies between 0 and

  1. 120°
  2. 30°
  3. 180°
  4. 90°
Show the answer

Answer: D. 90°

The time constant of a first-order system is the

  1. time taken by the controlled variable to reach 63.2% of its full change.
  2. same as transportation lag.
  3. same as dead time.
  4. time required by the measured variable to reach 63.2% of its ultimate change.
Show the answer

Answer: A. time taken by the controlled variable to reach 63.2% of its full change.

For two non-interacting first-order systems in series, the overall transfer function is the ____ of the individual ones.

  1. product
  2. ratio
  3. sum
  4. difference
Show the answer

Answer: A. product

The transfer function of a second-order system is

  1. 1/(T²s² + 2ζTs + 1)
  2. 1/(T²s² + 2Ts + 1)
  3. 1/(T²s² + 2ζT + 1)
  4. none of these
Show the answer

Answer: A. 1/(T²s² + 2ζTs + 1)

A system with damping coefficient equal to 1 is

  1. Overdamped.
  2. Critically damped.
  3. Underdamped.
  4. Highly fluctuating.
Show the answer

Answer: B. Critically damped.

For a second-order system under sinusoidal forcing, the phase lag

  1. is 30°
  2. is 90° at the most
  3. approaches 180° asymptotically
  4. is 120°
Show the answer

Answer: C. approaches 180° asymptotically

The dead zone of an instrument is the

  1. same as time constant.
  2. same as transportation lag.
  3. maximum change in the variable that does not change the reading of the instrument.
  4. none of these
Show the answer

Answer: C. maximum change in the variable that does not change the reading of the instrument.

The transfer function of a transportation (dead-time) lag is

  1. e^TS
  2. e^-TS
  3. 1/(Ts+1)
  4. none of these
Show the answer

Answer: B. e^-TS

The response of a control system to a change in set point is the

  1. frequency response
  2. transient response
  3. servo problem
  4. regulator problem
Show the answer

Answer: C. servo problem

For a response free of offset and with little oscillation, the best controller is

  1. proportional controller.
  2. proportional-derivative (PD) controller.
  3. proportional-integral (PI) controller.
  4. proportional-integral-derivative (PID) controller.
Show the answer

Answer: D. proportional-integral-derivative (PID) controller.

For an underdamped second-order system,

  1. decay ratio = overshoot
  2. decay ratio = (overshoot)²
  3. overshoot increases for increasing damping co-efficient.
  4. large damping co-efficient means smaller damping.
Show the answer

Answer: B. decay ratio = (overshoot)²

A stable system is one

  1. for which the output response is bounded for all bounded input.
  2. which exhibits an unbounded response to a bounded input
  3. which satisfies the conditions for a servo problem.
  4. none of these.
Show the answer

Answer: A. for which the output response is bounded for all bounded input.

The stability of a loop containing dead time is best analysed by

  1. Routh test
  2. root locus methods
  3. frequency response methods
  4. none of these
Show the answer

Answer: C. frequency response methods

An amplitude ratio is converted to decibels by

  1. Decibel = 20 log10 (AR)
  2. Decibel = 20 loge (AR)
  3. Decibel = 20 log10 (AR)^0.5
  4. Decibel = 20 loge (AR)^0.5
Show the answer

Answer: A. Decibel = 20 log10 (AR)

“A loop is unstable if the open-loop amplitude ratio exceeds 1 at the crossover frequency” is the ____ criterion.

  1. Bode stability
  2. Nyquist
  3. Routh stability
  4. none of these
Show the answer

Answer: A. Bode stability

Typical design specifications ask for gain margin and phase margin of

  1. >1.7 and >30°
  2. <1.7 and >30°
  3. <1.7 and <30°
  4. >1.7 and <30°
Show the answer

Answer: A. >1.7 and >30°

The frequency at which the amplitude ratio peaks is the ____ frequency.

  1. corner
  2. resonant
  3. cross-over
  4. natural
Show the answer

Answer: B. resonant

A negative gain margin in decibels indicates a/an ____ system.

  1. stable
  2. unstable
  3. critically damped
  4. none of these
Show the answer

Answer: B. unstable

A Bode diagram plots

  1. log (AR) vs. log (f) and φ vs. log (f).
  2. log (AR) vs. f and log φ vs. f.
  3. AR vs. log (f) and φ vs. log (f).
  4. none of these.
Show the answer

Answer: A. log (AR) vs. log (f) and φ vs. log (f).

The temperature of a red-hot furnace is best measured with a

  1. Platinum resistance thermometer
  2. Thermocouple
  3. Optical pyrometer
  4. Bimetallic thermometer
Show the answer

Answer: C. Optical pyrometer

An instrument’s ability to follow changes in the measured variable without dynamic error is its

  1. speed of response
  2. reproducibility
  3. fideility
  4. static characteristics
Show the answer

Answer: C. fideility

Which is a desirable instrument characteristic?

  1. High drift
  2. High fidelity
  3. High measuring lag
  4. Poor reproducibility
Show the answer

Answer: B. High fidelity

Which thermometer shows a noticeable initial “dip” (reading briefly moving the wrong way) on sudden heating?

  1. Mercury thermometer
  2. Radiation pyrometer
  3. Bimetallic thermometer
  4. Thermocouple
Show the answer

Answer: A. Mercury thermometer

For temperatures between −40 and 425 °C, a simple suitable instrument is a

  1. mercury thermometer
  2. bimetallic thermometer
  3. radiation pyrometer
  4. none of these
Show the answer

Answer: B. bimetallic thermometer

Thermocouples can measure

  1. liquid temperatures only.
  2. very high temperatures only.
  3. very low temperatures only.
  4. both high and low temperatures
Show the answer

Answer: D. both high and low temperatures

Heat absorbed or released at thermocouple junctions when current flows is the

  1. Seebeck effect
  2. Peltier effect
  3. Joule heating effect
  4. Thomson effect
Show the answer

Answer: B. Peltier effect

Thermowells are used in temperature measurement to

  1. guard against corrosive and oxidising action on thermocouple materials
  2. reduce measuring lag.
  3. increase the fidelity.
  4. increase the sensitivity.
Show the answer

Answer: A. guard against corrosive and oxidising action on thermocouple materials

Gas analysis in plants is commonly done with a

  1. thermal conductivity cell
  2. X-ray diffraction
  3. mass spectrometer
  4. emission spectrometer
Show the answer

Answer: A. thermal conductivity cell

A psychrometer measures the

  1. humidity of gases
  2. moisture content of solids
  3. water of crystallisation
  4. hygroscopic nature of solids
Show the answer

Answer: A. humidity of gases

In paper mills, moisture in the paper is continuously measured through its

  1. thermal conductivity through the paper
  2. electrical resistance through the paper
  3. magnetic susceptibility
  4. none of these
Show the answer

Answer: B. electrical resistance through the paper

A simple pitot tube measures the

  1. average velocity
  2. maximum velocity
  3. point velocity
  4. static pressure
Show the answer

Answer: C. point velocity

A Pirani gauge measures

  1. very high pressure.
  2. high vacuum.
  3. liquid level under pressure.
  4. liquid level at atmospheric pressure
Show the answer

Answer: B. high vacuum.

A barometer reads ____ pressure.

  1. absolute
  2. gauge
  3. absolute as well as gauge
  4. dynamic
Show the answer

Answer: A. absolute

The level of a liquid in a pressurised vessel can be measured with a

  1. bubbler system
  2. differential pressure manometer
  3. diaphragm box system
  4. air-trap system
Show the answer

Answer: B. differential pressure manometer

Specific gravity of a liquid can be measured continuously with a

  1. hydrometer
  2. contact-type electric indicators
  3. displacement meter
  4. both (a) and (c)
Show the answer

Answer: D. both (a) and (c)

A hot-wire anemometer measures

  1. flow rates of fluids.
  2. flow rates of granular solids.
  3. very high temperature.
  4. thermal conductivity of gases.
Show the answer

Answer: A. flow rates of fluids.

Flow through an orifice meter is ____ the pressure differential.

  1. proportional to
  2. inversely proportional to the square root of
  3. proportional to the square root of
  4. inversely proportional to the square of
Show the answer

Answer: C. proportional to the square root of

Which flowmeter is a variable-area meter?

  1. Venturimeter
  2. Rotameter
  3. Pitot tube
  4. Hot wire anemometer
Show the answer

Answer: B. Rotameter

In an exothermic reactor, the usual manipulated variable is the flow of

  1. coolant
  2. reactants
  3. product
  4. none of these
Show the answer

Answer: A. coolant

Adding integral action to proportional control

  1. elimination of offset
  2. reduction of offset
  3. reduction of stability time
  4. none of these
Show the answer

Answer: A. elimination of offset

Cascade control uses

  1. feed forward control.
  2. more than one feed-back loop.
  3. on-off control.
  4. one feed-back loop.
Show the answer

Answer: B. more than one feed-back loop.

Which controller gives the smallest maximum deviation?

  1. P-controller
  2. P-I controller
  3. P-I-D controller
  4. P-D controller
Show the answer

Answer: C. P-I-D controller

Pressure in an ammonia synthesis reactor is measured with a

  1. Bourdon gauge
  2. U-tube manometer
  3. Inclined tube manometer
  4. Pirani guage
Show the answer

Answer: A. Bourdon gauge

An absolute pressure of about 0.01 psi is measured with a ____ gauge.

  1. ionisation
  2. Pirani
  3. Mcloid
  4. none of these
Show the answer

Answer: B. Pirani

Continuous moisture measurement in paper uses a

  1. sling psychrometer.
  2. hair-hygrometer.
  3. weighing.
  4. high resistance Wheatstone's bridge circuit.
Show the answer

Answer: D. high resistance Wheatstone's bridge circuit.

An absolute pressure of about 0.0001 psi is measured with a ____ gauge.

  1. Mcloid
  2. Pirani
  3. thermocouple
  4. none of these
Show the answer

Answer: A. Mcloid

Thermocouple EMF is of the order of

  1. millivolts
  2. microvolts
  3. volts
  4. kilo volts
Show the answer

Answer: A. millivolts

Sub-zero Celsius temperatures in industry are most often measured with

  1. thermocouples
  2. resistance thermometers
  3. gas thermometers
  4. bi-metallic thermometers
Show the answer

Answer: B. resistance thermometers

An optical pyrometer is usable from about ____ °C upward.

  1. 800
  2. 400
  3. 1200
  4. 1500
Show the answer

Answer: A. 800

Which thermocouple suits about 1400 °C?

  1. Copper-constantan
  2. Aluminium-chromel
  3. Platinum-platinum+rhodium
  4. None of these
Show the answer

Answer: C. Platinum-platinum+rhodium

The interface level in a pressure vessel is measured with

  1. float
  2. manometers of float type
  3. U-tube manometer
  4. none of these
Show the answer

Answer: B. manometers of float type

Sludge flow is measured with a

  1. V-notch
  2. rectangular notch
  3. circular pipe
  4. Kennison nozzle
Show the answer

Answer: D. Kennison nozzle

The composition of natural gas is found with a

  1. chromatograph
  2. orsat apparatus
  3. spectrometer
  4. none of these
Show the answer

Answer: A. chromatograph

Instrument bellows are made of

  1. leather
  2. paper
  3. plastic
  4. thin copper sheet
Show the answer

Answer: D. thin copper sheet

A flapper–nozzle is the heart of a ____ controller.

  1. pneumatic
  2. hydraulic
  3. electronic
  4. none of these
Show the answer

Answer: A. pneumatic

A weir (diaphragm) valve is well suited to

  1. slurries
  2. acids
  3. neutral solutions
  4. bases
Show the answer

Answer: A. slurries

Fuel oil to a burner is commonly regulated with a ____ valve.

  1. gate
  2. butterfly
  3. rotary plug
  4. none of these
Show the answer

Answer: C. rotary plug

To send a control signal about one kilometre, the best mode is

  1. hydraulic
  2. pneumatic
  3. electronic
  4. none of these
Show the answer

Answer: C. electronic

A pilot relay in pneumatic transmission is used to

  1. speed up the signal.
  2. change the flow of air.
  3. adjust the signal.
  4. none of these.
Show the answer

Answer: B. change the flow of air.

Phase margin equals

  1. 180° - phase lag
  2. phase lag - 180°
  3. phase lag + 180°
  4. phase lag + 90°
Show the answer

Answer: A. 180° - phase lag

The Bode stability method works with the ____ loop transfer function.

  1. open
  2. closed
  3. either (a) or (b)
  4. neither (a) nor (b)
Show the answer

Answer: A. open

The Routh test is applied to the ____ loop characteristic equation.

  1. open
  2. closed
  3. either (a) or (b)
  4. neither (a) nor (b)
Show the answer

Answer: B. closed

A Nichols chart relates

  1. A.R. vs. phase lag of first order.
  2. A.R. vs. phase lag of second order.
  3. closed loop values vs. open loop values.
  4. frequency response values of controllers.
Show the answer

Answer: C. closed loop values vs. open loop values.

Hydraulic controllers use ____ as the working fluid.

  1. water
  2. steam
  3. air
  4. oil
Show the answer

Answer: D. oil

Which controller leaves the largest offset?

  1. P-controller
  2. P-I controller
  3. P-D controller
  4. P-I-D controller
Show the answer

Answer: A. P-controller

The degrees of freedom of a process give ____ number of controllers that can be installed.

  1. the maximum
  2. the minimum
  3. both maximum and the minimum
  4. nothing about the
Show the answer

Answer: A. the maximum

Gain margin equals the

  1. amplitude ratio
  2. reciprocal of amplitude ratio
  3. gain in P controller
  4. gain in P-I controller
Show the answer

Answer: B. reciprocal of amplitude ratio

A tiny freezing-point depression caused by a dissolved solute is best measured with a

  1. Beckman thermometer
  2. dilatometer
  3. mercury thermometer
  4. bimetallic thermometer
Show the answer

Answer: A. Beckman thermometer

A control system that uses feedback from output is called:

  1. Cascade control
  2. Open-loop control
  3. Feed-forward control
  4. Closed-loop control
Show the answer

Answer: D. Closed-loop control Closed-loop (feedback) control

An open-loop control system:

  1. Self-corrects errors
  2. More accurate than closed-loop
  3. Uses output feedback
  4. Has no feedback from output
Show the answer

Answer: D. Has no feedback from output

The difference between setpoint and measured value is called:

  1. Error
  2. Gain
  3. Integral
  4. Offset
Show the answer

Answer: A. Error Error (deviation)

PID stands for:

  1. None
  2. Proportional Integral Design
  3. Proportional Integral Derivative
  4. Process Instrument Diagram
Show the answer

Answer: C. Proportional Integral Derivative

The proportional controller output = Kc × e. What is Kc?

  1. Derivative time
  2. Controller gain
  3. Bias
  4. Integral time
Show the answer

Answer: B. Controller gain Controller gain (proportional gain)

Integral action in a PID controller eliminates:

  1. Oscillations
  2. Steady-state offset
  3. Overshoot
  4. Dead time
Show the answer

Answer: B. Steady-state offset Steady-state offset (bias)

Derivative action in a PID controller:

  1. Increases offset
  2. Predicts error trend and reduces overshoot
  3. Eliminates steady-state error
  4. Reduces gain
Show the answer

Answer: B. Predicts error trend and reduces overshoot

Transfer function is defined as:

  1. Ratio of Laplace transform of output to input
  2. Frequency ratio
  3. Time domain ratio
  4. None
Show the answer

Answer: A. Ratio of Laplace transform of output to input Ratio of Laplace transform of output to input (with zero initial conditions)

A first-order system transfer function G(s) = K/(τs+1). τ is:

  1. Dead time
  2. Natural frequency
  3. Time constant
  4. Gain
Show the answer

Answer: C. Time constant Time constant (time to reach 63.2% of final value)

A second-order underdamped system shows:

  1. Monotonic approach
  2. Oscillatory response with overshoot
  3. No overshoot
  4. Unstable response always
Show the answer

Answer: B. Oscillatory response with overshoot

Damping ratio ζ = 1 gives:

  1. Critically damped response
  2. Underdamped
  3. Unstable
  4. Overdamped
Show the answer

Answer: A. Critically damped response Critically damped response (fastest without oscillation)

The Bode plot shows:

  1. Time response
  2. Poles and zeros
  3. Step response
  4. Magnitude and phase vs. frequency
Show the answer

Answer: D. Magnitude and phase vs. frequency

Gain margin is the factor by which gain can be increased before:

  1. System becomes unstable
  2. Steady-state error appears
  3. Overshoot increases
  4. Oscillations start
Show the answer

Answer: A. System becomes unstable

Phase margin is the additional phase lag before:

  1. Gain becomes 0 dB
  2. None
  3. Steady state is reached
  4. System becomes unstable
Show the answer

Answer: D. System becomes unstable System becomes unstable (phase reaches -180°)

The Nyquist stability criterion is based on:

  1. The number of encirclements of -1 on Nyquist plot
  2. Root locus
  3. Routh array
  4. Bode plot
Show the answer

Answer: A. The number of encirclements of -1 on Nyquist plot

Routh-Hurwitz criterion determines stability by:

  1. Signs of elements in first column of Routh array
  2. Bode plot
  3. Frequency response
  4. Poles location
Show the answer

Answer: A. Signs of elements in first column of Routh array

A system is stable if all poles are in:

  1. Origin
  2. Imaginary axis
  3. Right-half
  4. Left-half of s-plane
Show the answer

Answer: D. Left-half of s-plane Left-half of s-plane (negative real part)

Root locus shows how closed-loop poles move as:

  1. Time varies
  2. Gain K varies from 0 to infinity
  3. Frequency varies
  4. Input varies
Show the answer

Answer: B. Gain K varies from 0 to infinity

Ziegler-Nichols tuning method uses:

  1. Mathematical model only
  2. Ultimate gain Ku and ultimate period Pu found experimentally
  3. Step response
  4. Frequency sweep
Show the answer

Answer: B. Ultimate gain Ku and ultimate period Pu found experimentally

A process with long dead time is:

  1. No effect on control
  2. Easiest to control
  3. Difficult to control needs detuned controller or Smith predictor
  4. Same as first-order
Show the answer

Answer: C. Difficult to control needs detuned controller or Smith predictor

Cascade control improves performance by:

  1. Reducing gain
  2. Inner fast loop rejecting disturbances before they affect outer loop
  3. Adding more sensors
  4. Eliminating integral
Show the answer

Answer: B. Inner fast loop rejecting disturbances before they affect outer loop

Feed-forward control corrects for disturbances:

  1. Without measurement
  2. Before they affect the process
  3. After they affect process
  4. None
Show the answer

Answer: B. Before they affect the process Before they affect the process (requires disturbance measurement)

Smith predictor is used for:

  1. Batch processes
  2. Non-linear processes
  3. Processes with large dead time to compensate delay in feedback
  4. Fast processes
Show the answer

Answer: C. Processes with large dead time to compensate delay in feedback

Model Predictive Control (MPC):

  1. Only uses current error
  2. Optimizes control actions over a future horizon using process model
  3. Same as PID
  4. Requires no model
Show the answer

Answer: B. Optimizes control actions over a future horizon using process model

The process gain Kp = change in output / change in input at:

  1. Steady state
  2. Time constant
  3. Zero
  4. Peak
Show the answer

Answer: A. Steady state

First-order plus dead time (FOPDT) model has:

  1. Two parameters
  2. Three parameters
  3. One parameter
  4. Four parameters
Show the answer

Answer: B. Three parameters Three parameters: gain K, time constant τ, dead time θ

Integral windup occurs when:

  1. Derivative is too large
  2. Controller output saturates while integral accumulates excessive error
  3. Gain is too low
  4. Process is nonlinear
Show the answer

Answer: B. Controller output saturates while integral accumulates excessive error

Anti-reset windup prevents:

  1. Steady-state offset
  2. Overshoot
  3. Excessive integral buildup during output saturation
  4. Oscillation
Show the answer

Answer: C. Excessive integral buildup during output saturation

A P-only controller has offset because:

  1. Process has dead time
  2. Finite proportional gain cannot drive error to zero at steady state
  3. Gain is too high
  4. It lacks derivative
Show the answer

Answer: B. Finite proportional gain cannot drive error to zero at steady state

The offset in P-only control is eliminated by adding:

  1. Integral action
  2. Derivative action
  3. Dead time compensation
  4. More gain
Show the answer

Answer: A. Integral action Integral (I) action

For a pure integrating process G(s) = K/s, a P-only controller gives:

  1. Large offset
  2. Instability always
  3. No steady-state offset
  4. Oscillations always
Show the answer

Answer: C. No steady-state offset No steady-state offset (process already integrates)

Split-range control uses one controller to drive:

  1. Only one valve
  2. No valves
  3. Multiple controllers
  4. Two or more valves over different ranges
Show the answer

Answer: D. Two or more valves over different ranges

Ratio control maintains the ratio between:

  1. Two process streams
  2. Two controllers
  3. Setpoint and output
  4. None
Show the answer

Answer: A. Two process streams Two process streams (e.g., fuel to air)

Feedforward with feedback combination:

  1. Feedforward handles measured disturbances, feedback corrects residual errors
  2. Not possible
  3. Only feedforward
  4. Only feedback
Show the answer

Answer: A. Feedforward handles measured disturbances, feedback corrects residual errors

Process variable (PV) in a control loop is:

  1. The disturbance
  2. The manipulated variable
  3. The measured output being controlled
  4. The setpoint
Show the answer

Answer: C. The measured output being controlled

Manipulated variable (MV) in a control loop is:

  1. The input adjusted by controller
  2. The measured output
  3. The setpoint
  4. The disturbance
Show the answer

Answer: A. The input adjusted by controller The input adjusted by controller (e.g., valve position)

Controlled variable is:

  1. The controller output
  2. The manipulated input
  3. The process output maintained at setpoint
  4. The error signal
Show the answer

Answer: C. The process output maintained at setpoint

For a heat exchanger temperature control, typical manipulated variable:

  1. Feed composition
  2. Process pressure
  3. Cooling/heating medium flow rate
  4. Feed temperature directly
Show the answer

Answer: C. Cooling/heating medium flow rate

A control valve with equal percentage characteristic:

  1. Used for level only
  2. Constant gain
  3. Decreasing gain
  4. Gain proportional to valve position
Show the answer

Answer: D. Gain proportional to valve position Gain proportional to valve position - good for pressure-dominated processes

Valve positioner is used to:

  1. Reduce pressure
  2. Control temperature
  3. Ensure valve reaches commanded position reducing hysteresis and friction
  4. Measure flow
Show the answer

Answer: C. Ensure valve reaches commanded position reducing hysteresis and friction

Level control in a tank often uses:

  1. PI or PID always
  2. Only differential pressure
  3. Only ultrasonic level
  4. P-only or PD control
Show the answer

Answer: D. P-only or PD control P-only or PD control (integral not needed for averaging level)

Pressure control in a gas system is typically:

  1. Requires derivative
  2. Same as level
  3. Fast response
  4. Very slow response
Show the answer

Answer: C. Fast response Fast response - P or PI controller sufficient

Flow control loop is characterized by:

  1. Long dead time typically
  2. Fast dynamics
  3. Slow dynamics
  4. Requires derivative
Show the answer

Answer: B. Fast dynamics Fast dynamics - high gain PI controller used

Temperature control loops are typically:

  1. Same as pressure
  2. Fast like flow
  3. Slow with dead time
  4. Requires cascade always
Show the answer

Answer: C. Slow with dead time Slow with dead time - PID with derivative action commonly used

Composition control (e.g., by GC analyser) has:

  1. Long dead time due to analyser cycle
  2. Fast response
  3. No dead time
  4. Simple P-only
Show the answer

Answer: A. Long dead time due to analyser cycle Long dead time due to analyser cycle - requires detuned controller or predictor

DCS (Distributed Control System) is:

  1. Computer-based control system with controllers distributed throughout plant
  2. Standalone controllers only
  3. Single central computer
  4. Manual panel only
Show the answer

Answer: A. Computer-based control system with controllers distributed throughout plant

PLC (Programmable Logic Controller) is primarily used for:

  1. High-level optimization
  2. Continuous PID control
  3. Sequential logic, on/off discrete control
  4. Analogue signals only
Show the answer

Answer: C. Sequential logic, on/off discrete control

SCADA stands for:

  1. Supervisory Control and Data Acquisition
  2. None
  3. System Control and Data Analysis
  4. Supervisory Computer Automated Design
Show the answer

Answer: A. Supervisory Control and Data Acquisition

ISA-5.1 standard covers:

  1. Instrumentation symbols and identification on P&IDs
  2. Pipe specifications
  3. Pressure vessel design
  4. Electrical standards
Show the answer

Answer: A. Instrumentation symbols and identification on P&IDs

A P&ID is a:

  1. Process Flow Diagram
  2. Electrical diagram
  3. Physical layout drawing
  4. Piping and Instrumentation Diagram showing all instruments and control loops
Show the answer

Answer: D. Piping and Instrumentation Diagram showing all instruments and control loops

The tag FIC-101 on a P&ID means:

  1. None
  2. Flow Indicating Controller loop 101
  3. Flow Isolation Check
  4. Filter Inlet Connector
Show the answer

Answer: B. Flow Indicating Controller loop 101

A transmitter converts:

  1. Process variable to standard signal
  2. Flow to temperature
  3. Setpoint to output
  4. Control signal to valve position
Show the answer

Answer: A. Process variable to standard signal Process variable to standard signal (4-20 mA or digital)

4-20 mA signal: 4 mA represents:

  1. 0% with live zero for wire-break detection
  2. 100%
  3. 50%
  4. Negative values
Show the answer

Answer: A. 0% with live zero for wire-break detection 0% (zero) with live zero for wire-break detection

HART protocol:

  1. Only for pH
  2. Superimposes digital signal on 4-20 mA loop for two-way communication
  3. Replaces 4-20 mA
  4. Only for wireless
Show the answer

Answer: B. Superimposes digital signal on 4-20 mA loop for two-way communication

Fieldbus technology:

  1. Wireless only
  2. Analogue communication
  3. Digital communication replacing 4-20 mA point-to-point wiring
  4. Only for gas detectors
Show the answer

Answer: C. Digital communication replacing 4-20 mA point-to-point wiring

A final control element is:

  1. The controller
  2. The sensor
  3. The transmitter
  4. The device that directly changes process variable
Show the answer

Answer: D. The device that directly changes process variable The device that directly changes process variable (e.g., valve, motor)

Control valve sizing coefficient Cv is defined by:

  1. Valve diameter
  2. Stem travel
  3. Actuator size
  4. Flow rate through valve at unit pressure drop for water
Show the answer

Answer: D. Flow rate through valve at unit pressure drop for water

Fail-safe position of control valve is chosen based on:

  1. None
  2. Cost of valve
  3. Process safety on loss of air/power
  4. Operator preference
Show the answer

Answer: C. Process safety on loss of air/power Process safety on loss of air/power (e.g., fail-closed for fuel)

A safety instrumented system (SIS) must be:

  1. Optional
  2. Part of BPCS
  3. Same as BPCS
  4. Independent of the basic process control system
Show the answer

Answer: D. Independent of the basic process control system Independent of the basic process control system (BPCS)

SIL (Safety Integrity Level) SIL 2 means probability of failure on demand (PFD) between:

  1. 10⁻² and 10⁻³
  2. 10⁻¹ and 10⁻²
  3. 10⁰ and 10⁻¹
  4. 10⁻³ and 10⁻⁴
Show the answer

Answer: A. 10⁻² and 10⁻³

Overshoot in a control system is:

  1. Rise time
  2. Response delay
  3. Percentage by which response exceeds setpoint before settling
  4. Steady-state error
Show the answer

Answer: C. Percentage by which response exceeds setpoint before settling

Rise time is:

  1. Dead time
  2. Time to settle
  3. Time to reach setpoint
  4. Time for response to rise from 10% to 90% of final value
Show the answer

Answer: D. Time for response to rise from 10% to 90% of final value

Settling time is:

  1. Peak time
  2. Time for response to stay within ±5% of final value
  3. Rise time
  4. Time to first reach setpoint
Show the answer

Answer: B. Time for response to stay within ±5% of final value Time for response to stay within ±5% (or ±2%) of final value

Dead time (transport delay) in a process is due to:

  1. None
  2. Plug flow transport delay, analyser cycle time, sensor lag
  3. Valve friction
  4. Controller processing time
Show the answer

Answer: B. Plug flow transport delay, analyser cycle time, sensor lag

Internal Model Control (IMC) parameter λ represents:

  1. Controller gain
  2. Dead time
  3. Process gain
  4. Desired closed-loop response speed
Show the answer

Answer: D. Desired closed-loop response speed Desired closed-loop response speed - larger λ = slower safer control

Inverse response (non-minimum phase) occurs in processes where:

  1. None
  2. Response is monotonic
  3. Initial response is opposite to final direction
  4. Dead time is large
Show the answer

Answer: C. Initial response is opposite to final direction Initial response is opposite to final direction (e.g., boiler drum level on increased firing)

The relative gain array (RGA) helps in:

  1. Tuning PID
  2. Stability analysis
  3. Single-loop design
  4. Pairing inputs and outputs in multivariable control systems
Show the answer

Answer: D. Pairing inputs and outputs in multivariable control systems

Decoupling in multivariable control aims to:

  1. Add more sensors
  2. Increase gain
  3. Reduce integral
  4. Eliminate or reduce interactions between control loops
Show the answer

Answer: D. Eliminate or reduce interactions between control loops

Adaptive control changes controller parameters based on:

  1. Only setpoint changes
  2. Changes in process dynamics over time
  3. Fixed model
  4. Disturbances only
Show the answer

Answer: B. Changes in process dynamics over time

Gain scheduling is a form of adaptive control where:

  1. Controller parameters are pre-set at different operating conditions
  2. Parameters self-adjust
  3. None
  4. Only gain changes
Show the answer

Answer: A. Controller parameters are pre-set at different operating conditions

Nonlinear control is needed when:

  1. Only batch processes
  2. Only temperature
  3. All processes
  4. Process exhibits significant nonlinearity that linear controllers cannot handle
Show the answer

Answer: D. Process exhibits significant nonlinearity that linear controllers cannot handle

Linearization of nonlinear process is done around:

  1. The setpoint only
  2. The maximum
  3. An operating point for use with linear controller design
  4. The minimum
Show the answer

Answer: C. An operating point for use with linear controller design An operating point (steady state) for use with linear controller design

For a process gain that varies with operating point, the product Kp × Kc should be:

  1. Roughly constant
  2. Always large
  3. = 1
  4. Always small
Show the answer

Answer: A. Roughly constant Roughly constant (compensate by adjusting Kc when Kp changes)

Frequency response methods (Bode Nyquist) determine:

  1. Transient response
  2. Step response only
  3. Stability margins and frequency-domain performance
  4. Time domain only
Show the answer

Answer: C. Stability margins and frequency-domain performance

The crossover frequency ωc is where:

  1. Phase = -180°
  2. Gain is minimum
  3. Gain is maximum
  4. Open-loop magnitude = 1 used to determine phase margin
Show the answer

Answer: D. Open-loop magnitude = 1 used to determine phase margin Open-loop magnitude = 1 (0 dB) used to determine phase margin

The phase crossover frequency ωpc is where:

  1. System oscillates
  2. Response peaks
  3. Magnitude = 0 dB
  4. Open-loop phase = -180° used to determine gain margin
Show the answer

Answer: D. Open-loop phase = -180° used to determine gain margin

A controller with Kc = 0 is:

  1. Maximum control
  2. Derivative only
  3. Integral only
  4. No control action
Show the answer

Answer: D. No control action No control action (manual or open-loop)

Derivative on measurement (vs derivative on error) avoids:

  1. Derivative kick when setpoint is stepped
  2. Steady-state offset
  3. Integral windup
  4. Oscillations
Show the answer

Answer: A. Derivative kick when setpoint is stepped

Setpoint weighting in PID reduces:

  1. Integral windup
  2. Overshoot on setpoint changes while maintaining disturbance rejection
  3. Steady-state error
  4. Dead time effect
Show the answer

Answer: B. Overshoot on setpoint changes while maintaining disturbance rejection

An interacting PID (series form) vs non-interacting (parallel/ideal):

  1. Both are common
  2. Interacting always better
  3. Non-interacting not used
  4. They are identical
Show the answer

Answer: A. Both are common Both are common - interacting couples I and D adjustments

The Cohen-Coon tuning rules are based on:

  1. Frequency sweep
  2. Open-loop process reaction curve
  3. Closed-loop oscillation test
  4. Simulation only
Show the answer

Answer: B. Open-loop process reaction curve Open-loop process reaction curve (step test identifying K, τ, θ)

Lambda (λ) tuning method sets:

  1. Closed-loop time constant λ as single tuning parameter
  2. Integral time directly
  3. Derivative time directly
  4. Ultimate period
Show the answer

Answer: A. Closed-loop time constant λ as single tuning parameter Closed-loop time constant λ as single tuning parameter - IMC-based PID

On-off (bang-bang) control is simplest but causes:

  1. Perfect control
  2. Continuous cycling around setpoint
  3. Steady-state offset
  4. No overshoot
Show the answer

Answer: B. Continuous cycling around setpoint Continuous cycling around setpoint (hunting)

Hysteresis (dead band) in on-off control:

  1. Has no effect
  2. Reduces cycling frequency at expense of larger offset deviation
  3. Increases cycling
  4. Eliminates offset
Show the answer

Answer: B. Reduces cycling frequency at expense of larger offset deviation

Inferential control estimates controlled variable from:

  1. Direct measurement
  2. Easier-measured secondary variable
  3. Setpoint only
  4. Simulation only
Show the answer

Answer: B. Easier-measured secondary variable Easier-measured secondary variable (e.g., tray temperature infers composition)

Statistical Process Control (SPC) monitors process using:

  1. Control charts to detect special causes
  2. PID control
  3. Manual inspection
  4. Advanced algorithms
Show the answer

Answer: A. Control charts to detect special causes Control charts (Shewhart charts) to detect special causes

A UCL/LCL in a control chart represents:

  1. Upper/Lower control limits
  2. Specification limits
  3. Alarm limits
  4. Safety limits
Show the answer

Answer: A. Upper/Lower control limits Upper/Lower control limits (typically ±3σ from mean)

Process capability index Cp = (USL - LSL) / (6σ). Cp > 1.33 means:

  1. Cp has no meaning
  2. Process is capable
  3. Process is marginally capable
  4. Process is not capable
Show the answer

Answer: B. Process is capable Process is capable - can meet specifications

Real-time optimization (RTO) operates:

  1. At supervisory level above MPC adjusting setpoints for economic optimum
  2. Same level as PID
  3. Below PID
  4. Only offline
Show the answer

Answer: A. At supervisory level above MPC adjusting setpoints for economic optimum

The control hierarchy from bottom to top is:

  1. RTO → MPC → PID
  2. PID → RTO → MPC
  3. PID → Advanced control → RTO → Business planning
  4. All at same level
Show the answer

Answer: C. PID → Advanced control → RTO → Business planning PID → Advanced control (MPC) → RTO → Business planning

A two-degrees-of-freedom (2DOF) controller separates:

  1. Setpoint tracking and disturbance rejection performance tuning
  2. Feedback and feedforward
  3. Single parameter tuning
  4. None
Show the answer

Answer: A. Setpoint tracking and disturbance rejection performance tuning

An analyser (online GC or NIR) in a control loop has:

  1. No dead time
  2. Large dead time equal to analyser cycle time
  3. Only for laboratory
  4. Instant response
Show the answer

Answer: B. Large dead time equal to analyser cycle time Large dead time equal to analyser cycle time (minutes)

The output bias in PID controller equals the steady-state output when:

  1. Error = 0 at operating point
  2. Setpoint = 0
  3. Error = 1
  4. Controller is manual
Show the answer

Answer: A. Error = 0 at operating point Error = 0 at operating point (integral sets this in I-containing controller)

Auto-tuning in modern controllers performs:

  1. Closed-loop relay test or step test to automatically identify process parameters
  2. Manual tuning only
  3. Tuning once at startup only
  4. No tuning
Show the answer

Answer: A. Closed-loop relay test or step test to automatically identify process parameters

P&ID stands for:

  1. Piping and Instrumentation Diagram
  2. Process and Instrument Drawing
  3. Piping and Instrument Design
  4. Plant and Instrument Diagram
Show the answer

Answer: A. Piping and Instrumentation Diagram

A PFD primarily shows:

  1. All piping sizes and schedules
  2. Electrical connections
  3. Instrument details
  4. Major equipment and process streams
Show the answer

Answer: D. Major equipment and process streams

ISA 5.1 standard governs:

  1. Instrumentation symbols and identification
  2. Equipment drawing standards
  3. Piping schedules
  4. Weld symbols
Show the answer

Answer: A. Instrumentation symbols and identification

FIC on a P&ID tag means:

  1. Feed Inlet Connection
  2. Flow Input Computer
  3. Flow Indicating Controller
  4. Flow Instrument Connection
Show the answer

Answer: C. Flow Indicating Controller

A sectional view reveals:

  1. Electrical layout
  2. External dimensions
  3. Piping layout
  4. Interior details of an object
Show the answer

Answer: D. Interior details of an object

First-angle projection is standard in:

  1. Australia
  2. Europe and Asia
  3. USA
  4. Canada
Show the answer

Answer: B. Europe and Asia

Third-angle projection is standard in:

  1. USA and Canada
  2. Europe
  3. Asia
  4. South America
Show the answer

Answer: A. USA and Canada

A hidden line on a drawing is shown as:

  1. Solid thin line
  2. Solid thick line
  3. Dashed line
  4. Chain line
Show the answer

Answer: C. Dashed line

Centre lines on drawings are shown as:

  1. Dotted lines
  2. Alternating long and short dashes
  3. Solid thin lines
  4. Dashed lines
Show the answer

Answer: B. Alternating long and short dashes

Schedule number of a pipe indicates:

  1. Wall thickness
  2. Flange rating
  3. Pipe material
  4. Nominal bore
Show the answer

Answer: A. Wall thickness

Nominal pipe size (NPS) refers to:

  1. Pipe weight per metre
  2. Wall thickness
  3. Exact outer diameter
  4. An approximate inner diameter designation
Show the answer

Answer: D. An approximate inner diameter designation

A centrifugal pump in P&ID typically shows:

  1. Circle with two lines
  2. Rectangle with inlet/outlet
  3. Triangle pointing upward
  4. Circle with an arrow indicating impeller
Show the answer

Answer: D. Circle with an arrow indicating impeller

Elevation drawing is a view from:

  1. Top
  2. Bottom
  3. Side
  4. Isometric angle
Show the answer

Answer: C. Side Side (front or rear)

Plan drawing is a view from:

  1. Front
  2. Top
  3. Side
  4. Cross-section
Show the answer

Answer: B. Top Top (overhead)

Equipment datasheet contains:

  1. Cost estimate
  2. Drawing number only
  3. Instrument tags
  4. Design conditions, materials, and performance data
Show the answer

Answer: D. Design conditions, materials, and performance data

PSV (Pressure Safety Valve) symbol shows:

  1. Spring-loaded valve with set point
  2. Control valve
  3. Check valve
  4. Globe valve symbol
Show the answer

Answer: A. Spring-loaded valve with set point

A globe valve symbol in P&ID looks like:

  1. Bowtie or figure-8
  2. Square on line
  3. Diamond
  4. Circle
Show the answer

Answer: A. Bowtie or figure-8

Ball valve symbol in P&ID:

  1. Triangle
  2. Circle with a bar
  3. Rectangle
  4. Diamond
Show the answer

Answer: B. Circle with a bar Circle with a bar (handle)

Gate valve symbol:

  1. Circle with a line
  2. Arrow
  3. Square
  4. Bowtie/hourglass shape
Show the answer

Answer: D. Bowtie/hourglass shape

A check valve symbol shows:

  1. Arrow indicating allowed flow direction
  2. Circle
  3. Square
  4. Bowtie
Show the answer

Answer: A. Arrow indicating allowed flow direction

Spectacle blind symbol shows:

  1. Triangle
  2. Square on line
  3. Two circles on pipe
  4. Single circle
Show the answer

Answer: C. Two circles on pipe Two circles (one solid, one outline) on pipe

Electrical signal line (4-20 mA) is shown as:

  1. Dotted
  2. Solid line with label
  3. Chain line
  4. Dashed
Show the answer

Answer: B. Solid line with label

Pneumatic signal line on P&ID:

  1. Dotted line
  2. Solid line
  3. Dashed line
  4. Chain line
Show the answer

Answer: C. Dashed line

A fired heater on PFD is shown as:

  1. Triangle
  2. Simple rectangle
  3. Rectangle with flame symbol inside
  4. Circle
Show the answer

Answer: C. Rectangle with flame symbol inside

A storage tank (fixed roof) on P&ID:

  1. Circle
  2. Diamond
  3. Rectangle
  4. Cylinder symbol with flat top
Show the answer

Answer: D. Cylinder symbol with flat top

A pressure vessel (vertical) symbol:

  1. Triangle
  2. Rectangle
  3. Circle
  4. Vertical cylinder with domed ends
Show the answer

Answer: D. Vertical cylinder with domed ends

A compressor on P&ID is shown as:

  1. Circle only
  2. Triangle or circle with arrow indicating rotation
  3. Diamond
  4. Rectangle
Show the answer

Answer: B. Triangle or circle with arrow indicating rotation

Battery limit on drawings is shown as:

  1. None
  2. Solid thick line
  3. Dashed or chain line across the drawing
  4. Dotted line
Show the answer

Answer: C. Dashed or chain line across the drawing

North arrow on plot plan indicates:

  1. None
  2. Process flow direction
  3. True or magnetic north direction for orientation
  4. Wind direction
Show the answer

Answer: C. True or magnetic north direction for orientation

Line number typically encodes:

  1. Only fluid service
  2. Only material
  3. Fluid service, line size, spec, insulation, sequence number
  4. Only pipe size
Show the answer

Answer: C. Fluid service, line size, spec, insulation, sequence number

As-built drawings reflect:

  1. Design intent only
  2. Actual installed configuration after construction
  3. Vendor data
  4. None
Show the answer

Answer: B. Actual installed configuration after construction

Red-lining drawings means:

  1. Marking up physical changes in red pen for as-built updates
  2. Error marking
  3. Drawing with red ink
  4. None
Show the answer

Answer: A. Marking up physical changes in red pen for as-built updates

Weld map marks:

  1. None
  2. Instrument tags
  3. Drawing number only
  4. Location and type of each weld for inspection and traceability
Show the answer

Answer: D. Location and type of each weld for inspection and traceability

Clash detection in 3D model helps to:

  1. None
  2. Identify physical interference between pipes, equipment, structures
  3. Draw P&IDs
  4. Calculate process flows
Show the answer

Answer: B. Identify physical interference between pipes, equipment, structures

Drawing scale 1:10 means:

  1. Object is drawn 10 times smaller than actual
  2. Arbitrary scale
  3. Object is 10 times larger
  4. Full size
Show the answer

Answer: A. Object is drawn 10 times smaller than actual

NTS on drawing means:

  1. None
  2. New Tee Section
  3. Next To Seam
  4. Not To Scale
Show the answer

Answer: D. Not To Scale

Rupture disc symbol on P&ID:

  1. Square
  2. Circle on a line
  3. Triangle on a line
  4. Diamond shape on a line
Show the answer

Answer: D. Diamond shape on a line

A detail drawing shows:

  1. P&ID
  2. Overall layout
  3. Entire plant
  4. Enlarged view of a specific part or connection
Show the answer

Answer: D. Enlarged view of a specific part or connection

3D plant design software examples:

  1. PDMS, SmartPlant, Intergraph
  2. Manual drafting
  3. None
  4. AutoCAD 2D only
Show the answer

Answer: A. PDMS, SmartPlant, Intergraph

Hazardous area classification is shown on:

  1. PFD
  2. Area classification drawing with zone boundaries
  3. P&ID
  4. None
Show the answer

Answer: B. Area classification drawing with zone boundaries

Equipment number format typically:

  1. Alphabetical only
  2. Numeric only
  3. Random numbers
  4. Type code + unit number + sequence
Show the answer

Answer: D. Type code + unit number + sequence Type code + unit number + sequence (e.g. E-101)

SIS on P&ID has:

  1. Only in text notes
  2. No distinction
  3. Separate dedicated symbols and SIL tagging
  4. Same symbols as basic controls
Show the answer

Answer: C. Separate dedicated symbols and SIL tagging

A Y-strainer symbol shows:

  1. Circle
  2. Arrow
  3. T-junction
  4. Y-shaped fitting on line
Show the answer

Answer: D. Y-shaped fitting on line

Underground piping on drawings:

  1. Thick solid lines
  2. Dashed or dotted lines
  3. Solid lines
  4. Chain lines
Show the answer

Answer: B. Dashed or dotted lines

Heat tracing on pipe in P&ID:

  1. Zigzag line alongside pipe
  2. Dashed line
  3. Dotted line
  4. Solid line
Show the answer

Answer: A. Zigzag line alongside pipe

A flame arrestor on P&ID:

  1. Two parallel plates symbol on line
  2. None
  3. Single valve symbol
  4. Circle
Show the answer

Answer: A. Two parallel plates symbol on line

Drawing revision control - latest revision:

  1. Color coding
  2. Letter or number in revision column with date and description
  3. No marking
  4. Symbol
Show the answer

Answer: B. Letter or number in revision column with date and description

Pipe support symbols include:

  1. Instrument symbols
  2. U-bolt, hanger, spring support symbols
  3. None
  4. Valve symbols
Show the answer

Answer: B. U-bolt, hanger, spring support symbols

Tie-in point on P&ID shows:

  1. Open pipe end
  2. Valve
  3. None
  4. Future connection point, often stub end with blind flange
Show the answer

Answer: D. Future connection point, often stub end with blind flange

Fabrication drawing for pressure vessel includes:

  1. Weld details, nozzle schedule, material list, dimensions
  2. P&ID connections only
  3. None
  4. Process conditions only
Show the answer

Answer: A. Weld details, nozzle schedule, material list, dimensions

DWG NO on title block means:

  1. Dimension without guide
  2. Drawing number
  3. None
  4. Design working group
Show the answer

Answer: B. Drawing number

Isometric piping drawing is used for:

  1. None
  2. Fabrication of piping spools showing exact routing in 3D
  3. Only layout planning
  4. P&ID only
Show the answer

Answer: B. Fabrication of piping spools showing exact routing in 3D

A line continuation symbol on P&ID:

  1. End of pipe
  2. Valve
  3. None
  4. Arrow with sheet/drawing number where line continues
Show the answer

Answer: D. Arrow with sheet/drawing number where line continues

Vendor data package (VDP) includes:

  1. Only drawings
  2. None
  3. Equipment drawings, datasheets, certificates, manuals supplied by equipment vendor
  4. Only certificates
Show the answer

Answer: C. Equipment drawings, datasheets, certificates, manuals supplied by equipment vendor

The 'as-built' P&ID reflects:

  1. Design intent only
  2. All changes made during construction and commissioning
  3. Vendor data
  4. None
Show the answer

Answer: B. All changes made during construction and commissioning

A functional specification describes:

  1. Material of construction
  2. Physical dimensions
  3. What an instrument or system must do
  4. None
Show the answer

Answer: C. What an instrument or system must do What an instrument or system must do (not how it does it)

IFC (Issued for Construction) drawings:

  1. Draft drawings
  2. Conceptual drawings
  3. None
  4. Final approved drawings used for actual construction
Show the answer

Answer: D. Final approved drawings used for actual construction

IFR (Issued for Review) drawings:

  1. Construction drawings
  2. None
  3. Approved drawings
  4. Drawings sent to client/discipline for comments before finalisation
Show the answer

Answer: D. Drawings sent to client/discipline for comments before finalisation

Hook-up drawing shows:

  1. Instrument installation details
  2. General arrangement
  3. None
  4. P&ID
Show the answer

Answer: A. Instrument installation details Instrument installation details - tubing, fittings, valves connections to instrument

Instrument index (register):

  1. None
  2. Material list
  3. List of all instruments with tag, type, range, set point, P&ID reference
  4. Drawing list
Show the answer

Answer: C. List of all instruments with tag, type, range, set point, P&ID reference

Plot plan scale typically:

  1. 1:10
  2. None
  3. 1:200 or 1:500 for large plants
  4. 1:1
Show the answer

Answer: C. 1:200 or 1:500 for large plants

Piping flexibility analysis checks:

  1. None
  2. Pressure drop only
  3. Flow rate
  4. Thermal expansion stresses in piping to prevent over-stress or flange leaks
Show the answer

Answer: D. Thermal expansion stresses in piping to prevent over-stress or flange leaks

Caesar II is a software for:

  1. P&ID drawing
  2. 3D modelling
  3. Piping stress analysis
  4. None
Show the answer

Answer: C. Piping stress analysis

Datasheet for centrifugal pump includes:

  1. Only flow
  2. None
  3. Only head
  4. Flow, head, NPSH, efficiency, shaft power, driver type, material, flange rating
Show the answer

Answer: D. Flow, head, NPSH, efficiency, shaft power, driver type, material, flange rating

P&ID revision cloud:

  1. Only title block change
  2. Full redraw
  3. None
  4. Cloud-shaped marking around changed area to highlight revision clearly
Show the answer

Answer: D. Cloud-shaped marking around changed area to highlight revision clearly

North arrow importance on plot plan:

  1. Decorative only
  2. Wind direction
  3. Gives orientation reference for all equipment coordinates and pipe routing
  4. None
Show the answer

Answer: C. Gives orientation reference for all equipment coordinates and pipe routing

Instrument line - capillary tubing on P&ID:

  1. Dotted line
  2. Shown as dashed line with notation for filled system
  3. None
  4. Solid line
Show the answer

Answer: B. Shown as dashed line with notation for filled system Shown as dashed line with notation for filled system (temperature element)

Category of drawing for FEED (Front-End Engineering Design):

  1. Preliminary P&IDs, PFDs, plot plans for cost estimation and basic design
  2. None
  3. Detailed fabrication drawings
  4. As-built drawings
Show the answer

Answer: A. Preliminary P&IDs, PFDs, plot plans for cost estimation and basic design

EPC contract:

  1. Engineering, Procurement, and Construction
  2. None
  3. Only procurement
  4. Only engineering
Show the answer

Answer: A. Engineering, Procurement, and Construction Engineering, Procurement, and Construction - one contractor delivers complete plant

EPCC contract adds:

  1. Only construction
  2. Only engineering
  3. None
  4. Commissioning to EPC scope
Show the answer

Answer: D. Commissioning to EPC scope Commissioning (C) to EPC scope

CFD (Computational Fluid Dynamics) in piping:

  1. Only 1D analysis
  2. Only pressure drop
  3. None
  4. Analyses complex flow patterns, pressure drops, mixing in 3D models
Show the answer

Answer: D. Analyses complex flow patterns, pressure drops, mixing in 3D models

Open/closed loop control on P&ID:

  1. Both same
  2. Closed loop
  3. None
  4. Open loop has sensor
Show the answer

Answer: B. Closed loop Closed loop: sensor → controller → final element; open loop: manual set point or direct action

Cascade control on P&ID:

  1. None
  2. Single loop only
  3. Secondary loop controlled by output of primary loop
  4. Feedforward only
Show the answer

Answer: C. Secondary loop controlled by output of primary loop Secondary (inner) loop controlled by output of primary (outer) loop - e.g. flow setpoint set by level controller

Ratio control:

  1. Feedforward
  2. Maintains fixed ratio between two flows
  3. None
  4. Cascade control
Show the answer

Answer: B. Maintains fixed ratio between two flows Maintains fixed ratio between two flows (e.g. fuel:air ratio) - ratio controller symbol on P&ID

Feedforward control on P&ID:

  1. Feedback only
  2. Measures disturbance and corrects before it upsets the process
  3. None
  4. Ratio control
Show the answer

Answer: B. Measures disturbance and corrects before it upsets the process Measures disturbance and corrects before it upsets the process - triangle/FF notation

Override (select) control:

  1. Ratio
  2. None
  3. Cascade
  4. High select or low select of two signals
Show the answer

Answer: D. High select or low select of two signals High select or low select of two signals - limits output variable (HS/LS symbol)

DCS tag numbering convention:

  1. <Measured variable><Function><Loop number> e.g. FIC-101 = Flow Indicating Controller loop 101
  2. Only numbers
  3. None
  4. Random
Show the answer

Answer: A. <Measured variable><Function><Loop number> e.g. FIC-101 = Flow Indicating Controller loop 101

Control valve fail position:

  1. None
  2. Always fail open
  3. Always fail closed
  4. FC = fail closed; FO = fail open
Show the answer

Answer: D. FC = fail closed; FO = fail open FC = fail closed; FO = fail open - defined for safety on loss of air/signal

Globe valve trim:

  1. V-port, equal percentage, linear, quick-opening
  2. Only ball valve
  3. None
  4. Not applicable
Show the answer

Answer: A. V-port, equal percentage, linear, quick-opening V-port, equal percentage, linear, quick-opening - determines installed characteristic

Cv of control valve:

  1. None
  2. Flow coefficient
  3. Kv
  4. No sizing needed
Show the answer

Answer: B. Flow coefficient Flow coefficient - US gal/min of water at 1 psi ΔP - sizes valve

Smart (SMART) transmitter on P&ID:

  1. Digital transmitter with HART or fieldbus communication
  2. None
  3. Analogue only
  4. No difference shown
Show the answer

Answer: A. Digital transmitter with HART or fieldbus communication Digital transmitter with HART or fieldbus communication - square or hexagonal bubble

Instrument air supply on P&ID:

  1. Hydraulic
  2. Shown as dashed line from IA header or noted as utility at instrument connections
  3. Electrical signal
  4. None
Show the answer

Answer: B. Shown as dashed line from IA header or noted as utility at instrument connections

DCS interlock on P&ID:

  1. Software interlock shown by diamond/logic symbol or reference to interlock schedule
  2. None
  3. Hard-wired always
  4. Not shown
Show the answer

Answer: A. Software interlock shown by diamond/logic symbol or reference to interlock schedule

SIS trip on P&ID:

  1. Same as DCS
  2. Dedicated safety layer
  3. No separation
  4. None
Show the answer

Answer: B. Dedicated safety layer Dedicated safety layer - separate from DCS; shown with separate instrument bubble notation or SIS prefix

ESD (Emergency Shutdown) valve symbol:

  1. No distinction
  2. None
  3. Ball valve or gate valve with actuator and position feedback
  4. Regular valve
Show the answer

Answer: C. Ball valve or gate valve with actuator and position feedback Ball valve or gate valve with actuator and position feedback - normally open or closed

High/low alarm on P&ID:

  1. None
  2. HAH/LAH = high-high/low-low alarm; HAL/LAL = high/low alarm
  3. Not shown on P&ID
  4. Optional notation
Show the answer

Answer: B. HAH/LAH = high-high/low-low alarm; HAL/LAL = high/low alarm HAH/LAH = high-high/low-low alarm; HAL/LAL = high/low alarm - defined in bubble

PAHH (Pressure Alarm High-High):

  1. Only for liquids
  2. Safety alarm triggering emergency action at highest pressure
  3. None
  4. Same as PAH
Show the answer

Answer: B. Safety alarm triggering emergency action at highest pressure Safety alarm triggering emergency action (SIS trip) at highest pressure - separate from PAH

Instrument loop diagram:

  1. None
  2. General arrangement
  3. P&ID
  4. Detailed wiring/tubing of single instrument loop
Show the answer

Answer: D. Detailed wiring/tubing of single instrument loop Detailed wiring/tubing of single instrument loop - terminal strips, cable numbers, power supply

Junction box (J/B) on instrument loop diagram:

  1. Instrument bubble
  2. None
  3. Terminal strip inside box where field wiring joins instrument cable
  4. Nothing
Show the answer

Answer: C. Terminal strip inside box where field wiring joins instrument cable Terminal strip inside box where field wiring joins instrument cable - shown as rectangle

Marshalling cabinet:

  1. Field instrument
  2. DCS cabinet directly
  3. None
  4. Intermediate cabinet where field cables are terminated before DCS I/O
Show the answer

Answer: D. Intermediate cabinet where field cables are terminated before DCS I/O Intermediate cabinet where field cables are terminated before DCS I/O - minimises long cable runs to DCS

Multicore cable for instruments:

  1. One cable per instrument always
  2. Wireless only
  3. Multiple pairs in one cable
  4. None
Show the answer

Answer: C. Multiple pairs in one cable Multiple pairs in one cable - cost-effective for multiple instruments in same area

Intrinsic safety (Ex i) barrier:

  1. Explosion-proof only
  2. Limits energy to field instrument in hazardous area
  3. None
  4. No protection
Show the answer

Answer: B. Limits energy to field instrument in hazardous area Limits energy to field instrument in hazardous area - Zener barrier or galvanic isolator

Explosion-proof (Ex d) enclosure:

  1. Instrument in flameproof housing that contains internal explosion without propagating outside
  2. None
  3. Intrinsic safety
  4. Purged enclosure
Show the answer

Answer: A. Instrument in flameproof housing that contains internal explosion without propagating outside

Purged/pressurised enclosure (Ex p):

  1. None
  2. Housing filled with inert gas under positive pressure
  3. Explosion-proof
  4. Intrinsic safety
Show the answer

Answer: B. Housing filled with inert gas under positive pressure Housing filled with inert gas under positive pressure - excludes flammable atmosphere

Thermowell function:

  1. Isolation valve
  2. None
  3. Direct immersion
  4. Protects temperature element from process fluid while allowing heat conduction
Show the answer

Answer: D. Protects temperature element from process fluid while allowing heat conduction Protects temperature element from process fluid while allowing heat conduction - removable without shutdown

Orifice plate flow measurement:

  1. Positive displacement
  2. None
  3. Differential pressure across orifice ∝ flow²
  4. Turbine meter
Show the answer

Answer: C. Differential pressure across orifice ∝ flow² Differential pressure across orifice ∝ flow² - indicated by DP transmitter

Coriolis flow meter principle:

  1. None
  2. Differential pressure
  3. Magnetic
  4. Measures mass flow directly via Coriolis effect on vibrating tubes
Show the answer

Answer: D. Measures mass flow directly via Coriolis effect on vibrating tubes Measures mass flow directly via Coriolis effect on vibrating tubes - also gives density

Magnetic (electromagnetic) flow meter:

  1. Gas flow
  2. Non-conductive liquids
  3. Measures conductive liquid flow via Faraday's law
  4. None
Show the answer

Answer: C. Measures conductive liquid flow via Faraday's law Measures conductive liquid flow via Faraday's law - velocity ∝ induced EMF

Ultrasonic flow meter (clamp-on):

  1. Non-invasive
  2. Process wetted
  3. DP type
  4. None
Show the answer

Answer: A. Non-invasive Non-invasive - measures transit time difference between upstream/downstream ultrasonic pulses

Level measurement - differential pressure method:

  1. None
  2. ΔP between vessel bottom tap and top tap gives liquid level
  3. Only open vessels
  4. Only float
Show the answer

Answer: B. ΔP between vessel bottom tap and top tap gives liquid level ΔP between vessel bottom tap and top tap gives liquid level - most common for closed vessels

Radar (guided wave) level measurement:

  1. Microwave pulses reflect off liquid surface
  2. Float type
  3. Displacer
  4. None
Show the answer

Answer: A. Microwave pulses reflect off liquid surface Microwave pulses reflect off liquid surface - used for corrosive, viscous, or high-T liquids

PSSR (Pre-Startup Safety Review):

  1. [
  2. "
  3. i
  4. F
Show the answer

Answer: A. [

Cold eyes review:

  1. I
  2. "
  3. n
  4. [
Show the answer

Answer: D. [

As-built vs AFC (Approved for Construction) drawings:

  1. [
  2. F
  3. A
  4. "
Show the answer

Answer: A. [

PDMS database extract:

  1. [
  2. "
  3. l
  4. P
Show the answer

Answer: A. [

Process flow assurance:

  1. n
  2. [
  3. E
  4. "
Show the answer

Answer: B. [

Living document concept in P&ID:

  1. &
  2. P
  3. "
  4. [
Show the answer

Answer: D. [

Safe access platform on vessel general arrangement:

  1. l
  2. P
  3. [
  4. "
Show the answer

Answer: C. [

Hazardous area plot plan layer:

  1. O
  2. "
  3. v
  4. [
Show the answer

Answer: D. [

Valve schedule (valve list):

  1. [
  2. a
  3. D
  4. "
Show the answer

Answer: A. [

Equipment list purpose:

  1. T
  2. [
  3. "
  4. a
Show the answer

Answer: B. [

Tie-back drawing:

  1. h
  2. [
  3. S
  4. "
Show the answer

Answer: B. [

DWG revision cloud purpose:

  1. H
  2. "
  3. i
  4. [
Show the answer

Answer: D. [

Instrument specification sheet:

  1. "
  2. D
  3. [
  4. e
Show the answer

Answer: C. [

'IFI' (Issued For Information) drawing:

  1. [
  2. E
  3. "
  4. a
Show the answer

Answer: A. [

Material class (piping class/spec):

  1. "
  2. [
  3. e
  4. D
Show the answer

Answer: B. [

Spool isometric drawing includes:

  1. None
  2. Only material
  3. Only dimensions
  4. Pipe spool number, material, dimensions, weld joints, supports, and test requirements
Show the answer

Answer: D. Pipe spool number, material, dimensions, weld joints, supports, and test requirements

Line specification break on P&ID:

  1. End of pipe
  2. None
  3. Shows change of pipe spec on same line
  4. Valve symbol
Show the answer

Answer: C. Shows change of pipe spec on same line Shows change of pipe spec (material, rating) on same line - break symbol with new spec label

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →