IITIAN1997 STUDIO

Heat transfer and evaporation (Unit Operation-I and III)

JLEE CHE · 287 practice questions with answers

Practise and take a mock test →

Conduction, convection, radiation, exchangers and evaporators

Topics: Fourier’s law, conduction through plane, cylindrical and composite walls, thermal conductivity, insulation and critical radius; convection, film coefficients, dimensionless numbers (Nu, Pr, Gr); overall heat-transfer coefficient, fouling; LMTD, co-current and counter-current flow, double-pipe and shell-and-tube exchangers; boiling and condensation; radiation (Stefan–Boltzmann, black and grey bodies, emissivity); evaporators (single and multiple effect, economy, capacity).

Conduction

Fourier’s law: q = −kA dT/dx; through a flat wall q = kAΔT/x. Walls in series add their resistances R = x/(kA), like resistors in series. For a cylinder, R = ln(r₂/r₁)/(2πkL).

Insulating a small pipe can increase heat loss until the outer radius reaches the critical radius r_c = k/h, because the outer surface area grows faster than the resistance.

  • q = kAΔT/x
  • Series walls: R_total = Σ x/(kA)
  • Critical radius r_c = k/h

Example: A wall 0.2 m thick (k = 0.8 W/m·K) has area 10 m² and a 30 K temperature difference. Find q.

  1. q = 0.8 × 10 × 30 / 0.2.
  2. = 1200 W.

Answer: 1200 W

Example: Per m², a wall has 0.2 m brick (k = 0.8) and 0.05 m insulation (k = 0.05). Find q for ΔT = 100 K.

  1. R = 0.2/0.8 + 0.05/0.05 = 0.25 + 1.0 = 1.25 m²K/W.
  2. q = 100/1.25 = 80 W/m².

Answer: 80 W/m²

Example: Find the critical radius of insulation with k = 0.05 W/m·K and h = 10 W/m²·K.

  1. r_c = k/h = 0.05/10.
  2. = 0.005 m = 5 mm.

Answer: 5 mm

Convection and the overall coefficient

Convection: q = hAΔT. The film coefficient h depends on flow and fluid properties through dimensionless numbers: Nusselt (hD/k), Prandtl (Cpμ/k), Reynolds and Grashof (natural convection). For turbulent flow in tubes, Dittus–Boelter: Nu = 0.023 Re^0.8 Pr^n.

An exchanger’s overall coefficient combines the resistances: 1/U = 1/hᵢ + x_w/k_w + 1/h_o + fouling resistances. The smallest h controls U.

  • q = hAΔT
  • 1/U = 1/hᵢ + x/k + 1/h_o + R_f
  • Nu = 0.023 Re^0.8 Pr^n (turbulent)

Example: hᵢ = 1000 and h_o = 500 W/m²K; the wall resistance is negligible. Find U.

  1. 1/U = 1/1000 + 1/500 = 0.003.
  2. U = 333 W/m²K.

Answer: ≈ 333 W/m²K

Heat exchangers, LMTD and evaporators

The driving force in an exchanger is the log-mean temperature difference: LMTD = (ΔT₁ − ΔT₂)/ln(ΔT₁/ΔT₂), using the end differences. Counter-current flow gives a larger LMTD than co-current for the same terminal temperatures. Q = UA·LMTD.

Evaporators concentrate solutions with steam. Steam economy = kg of water evaporated per kg of steam; multiple-effect evaporators reuse vapour from one effect to heat the next, raising economy roughly in proportion to the number of effects.

  • LMTD = (ΔT₁ − ΔT₂)/ln(ΔT₁/ΔT₂)
  • Q = U A LMTD
  • Economy = water evaporated / steam used

Example: Hot fluid 150 → 100 °C, cold 30 → 80 °C. Find the LMTD for counter-current and co-current flow.

  1. Counter: ΔT₁ = 150 − 80 = 70, ΔT₂ = 100 − 30 = 70, so LMTD = 70 °C.
  2. Co-current: ΔT₁ = 120, ΔT₂ = 20, LMTD = 100/ln 6 ≈ 55.8 °C.

Answer: 70 °C and ≈ 55.8 °C

Example: With U = 333 W/m²K and LMTD = 70 °C, what area transfers 100 kW?

  1. A = Q/(U·LMTD) = 100 000/(333 × 70).
  2. ≈ 4.29 m².

Answer: ≈ 4.3 m²

Conduction follows Fourier’s law q = −kA dT/dx, so a plane wall conducts Q = kAΔT/x; walls in series add their resistances x/(kA). Convection is Q = hAΔT, with h from correlations of Nusselt (hD/k), Reynolds and Prandtl (cₚμ/k) numbers — e.g. Dittus–Boelter Nu = 0.023Re^0.8Pr^n. An exchanger transfers Q = UAΔT_lm; counter-current flow gives the larger LMTD for the same terminal temperatures. Radiation from a body is q = εσT⁴ (σ = 5.67 × 10⁻⁸ W/m²K⁴); a black body has ε = 1. In multiple-effect evaporators the steam economy rises roughly with the number of effects while the capacity stays about the same as one effect with the same total ΔT.

  • Critical radius of insulation for a cylinder r_c = k/h.
  • Film-wise condensation gives lower h than drop-wise condensation.
  • Nucleate boiling has the highest h; beyond the critical heat flux film boiling sets in.
  • 1/U = 1/hᵢ + x/k + 1/h_o + fouling resistances.
  • Kirchhoff’s law: at thermal equilibrium emissivity = absorptivity.

Key formulas

  • Q = kAΔT/x
  • Q = hAΔT
  • Q = UAΔT_lm
  • ΔT_lm = (ΔT₁ − ΔT₂)/ln(ΔT₁/ΔT₂)
  • q = εσT⁴

Practice questions

Fourier’s law applies to

  1. convection
  2. conduction
  3. radiation
  4. boiling
Show the answer

Answer: B. conduction q = −k dT/dx.

The Nusselt number is

  1. hD/k
  2. cₚμ/k
  3. ρvD/μ
  4. gβΔTL³/ν²
Show the answer

Answer: A. hD/k Ratio of convective to conductive transfer.

The Prandtl number is

  1. hD/k
  2. cₚμ/k
  3. μ/ρD
  4. hL/k
Show the answer

Answer: B. cₚμ/k Momentum vs thermal diffusivity.

For the same terminal temperatures, LMTD is largest for

  1. co-current flow
  2. counter-current flow
  3. cross flow
  4. it is the same
Show the answer

Answer: B. counter-current flow Counter-current.

The critical radius of insulation for a pipe is

  1. k/h
  2. h/k
  3. 2k/h
  4. k/2h
Show the answer

Answer: A. k/h r_c = k/h.

A black body has emissivity

  1. 0
  2. 0.5
  3. 1
  4. depends on T
Show the answer

Answer: C. 1 Perfect emitter.

Radiative emission is proportional to

  1. T
  2. T²
  3. T³
  4. T⁴
Show the answer

Answer: D. T⁴ Stefan–Boltzmann law.

Drop-wise condensation gives a heat-transfer coefficient that is

  1. lower than film-wise
  2. higher than film-wise
  3. same
  4. zero
Show the answer

Answer: B. higher than film-wise Bare surface exposed.

Steam economy of an evaporator is

  1. kg vapour produced per kg steam
  2. kg steam per kg feed
  3. heat transferred per unit area
  4. capacity per hour
Show the answer

Answer: A. kg vapour produced per kg steam Definition.

The Grashof number appears in

  1. forced convection
  2. natural convection
  3. radiation
  4. conduction
Show the answer

Answer: B. natural convection Buoyancy-driven flow.

Fouling factors in an exchanger

  1. increase U
  2. decrease U
  3. do not affect U
  4. increase LMTD
Show the answer

Answer: B. decrease U Extra resistances.

Thermal conductivity is highest for

  1. air
  2. water
  3. copper
  4. glass wool
Show the answer

Answer: C. copper Metals conduct best.

An uninsulated steam pipe loses heat to the air by

  1. conduction
  2. convection
  3. radiation
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

Fourier’s law describes heat transfer by

  1. convection
  2. radiation
  3. conduction
  4. all (a), (b) and (c)
Show the answer

Answer: C. conduction

Heat conduction is unsteady when

  1. temperature distribution is independent of time.
  2. temperature distribution is dependent on time.
  3. heat flows in one direction only.
  4. three dimensional heat flow is concerned.
Show the answer

Answer: B. temperature distribution is dependent on time.

Thermal conductivity can be expressed in

  1. Kcal/hr. m² °C
  2. Kcal/hr.m.°C
  3. Kcal/hr.m
  4. Kcal/hr. °C
Show the answer

Answer: B. Kcal/hr.m.°C

A heat-transfer coefficient can be expressed in

  1. BTU/hr. ft² °F
  2. BTU/hr. °F. ft.
  3. BTU/hr. °F
  4. BTU/hr. ft
Show the answer

Answer: A. BTU/hr. ft² °F

A good insulator should have

  1. low thermal conductivity.
  2. high thermal conductivity.
  3. less resistance to heat flow.
  4. a porous structure.
Show the answer

Answer: A. low thermal conductivity.

Heat flowing through resistances in series is like electric current through

  1. resistances in parallel.
  2. capacitors in series.
  3. resistances in series.
  4. none of these.
Show the answer

Answer: C. resistances in series.

For flat layers in series, the overall thermal resistance is the ____ of the individual resistances.

  1. average
  2. geometric mean
  3. product
  4. sum
Show the answer

Answer: D. sum

Which has the highest thermal conductivity?

  1. Brick
  2. Air
  3. Water
  4. Silver
Show the answer

Answer: D. Silver

For conduction through a cylinder wall, the area used is the

  1. Logarithmic mean area
  2. Arithmetic mean area
  3. Geometric mean area
  4. None of these
Show the answer

Answer: A. Logarithmic mean area

For heat flow through a very thick-walled cylinder, use the ____ mean radius.

  1. arithmetic
  2. logarithmic
  3. geometric
  4. either (a) or (c)
Show the answer

Answer: B. logarithmic

The logarithmic mean of r₁ and r₂ is

  1. (r₁ − r₂)/ln(r₁/r₂)
  2. (r₁ − r₂)/ln(r₂/r₁)
  3. (r₂ − r₁)/(r₁ r₂)
  4. (r₁ + r₂)/2
Show the answer

Answer: A. (r₁ − r₂)/ln(r₁/r₂)

The Nusselt number is

  1. Cp,μ/k
  2. hD/k
  3. hCp/μ
  4. Cp·μ/h
Show the answer

Answer: B. hD/k

The Prandtl number is

  1. Cp·μ/a
  2. hD/k
  3. Cp·μ/k
  4. μ/h·Cp
Show the answer

Answer: C. Cp·μ/k

Thermal diffusivity equals

  1. k/(ρ·Cp)
  2. ρ·Cp/k
  3. Cp·μ/a
  4. μ/h·Cp
Show the answer

Answer: A. k/(ρ·Cp)

The Grashof number is

  1. gD³βΔT ρ²/μ²
  2. gD²βΔT ρ/μ²
  3. gD²βΔT ρ²/μ
  4. gD³βΔT ρ²/μ
Show the answer

Answer: A. gD³βΔT ρ²/μ²

With inside film coefficient h₁ and outside coefficient h₂, the overall coefficient U is

  1. always less than the smaller of h₁ and h₂
  2. always between h₁ and h₂
  3. always higher than h₁
  4. independent of the film coefficients
Show the answer

Answer: A. always less than the smaller of h₁ and h₂

The Graetz number is

  1. mCp/kL
  2. kL/mCp
  3. mCp/kμ
  4. mk/CpL
Show the answer

Answer: A. mCp/kL

In Q = UAΔt for an exchanger, Δt is the

  1. geometric mean temperature difference.
  2. arithmetic mean temperature difference.
  3. logarithmic mean temperature difference.
  4. the difference of average bulk temperatures of hot and cold fluids.
Show the answer

Answer: C. logarithmic mean temperature difference.

The Peclet number equals

  1. Pe = Re.Pr
  2. Pe = Re/Pr
  3. Pe = Pr/Re
  4. Pe = Nu.Re
Show the answer

Answer: A. Pe = Re.Pr

The highest heat-transfer rate is obtained in ____ flow.

  1. laminar
  2. turbulent
  3. creeping
  4. transition region
Show the answer

Answer: B. turbulent

Heat flux is the rate of heat transfer per unit

  1. length
  2. area
  3. volume
  4. none of these
Show the answer

Answer: B. area

A fouling factor

  1. is a dimensionless quantity.
  2. does not provide a safety factor for design.
  3. accounts for additional resistances to heat flow.
  4. none of these.
Show the answer

Answer: C. accounts for additional resistances to heat flow.

As temperature rises, gas viscosity

  1. increase very rapidly
  2. increase slowly
  3. decrease slowly
  4. remain unaffected
Show the answer

Answer: B. increase slowly

The heat-transfer coefficient of a liquid increases with

  1. increasing temperature.
  2. decreasing temperature.
  3. decreasing Reynolds number.
  4. none of these.
Show the answer

Answer: A. increasing temperature.

Above what Prandtl number is conduction negligible in the turbulent core of a fluid in a heated pipe?

  1. 0.5
  2. <0.5
  3. >0.6
  4. <0.1
Show the answer

Answer: C. >0.6

For Pr > 1, conduction in a fluid flowing through a heated pipe is confined to the

  1. buffer zone
  2. turbulent core
  3. both (a) and (b)
  4. viscous sub-layer
Show the answer

Answer: D. viscous sub-layer

Conduction is significant in the buffer zone of a heated pipe only when Pr is

  1. 0.1
  2. >1
  3. <1
  4. 1
Show the answer

Answer: B. >1

Natural convection is characterised by the ____ number.

  1. Grashhoff number
  2. Peclet number
  3. Reynolds number
  4. Prandtl number
Show the answer

Answer: A. Grashhoff number

Which dimensionless group is unimportant in forced convection?

  1. Reynolds number
  2. Prandtl number
  3. Grashhoff number
  4. none of these
Show the answer

Answer: C. Grashhoff number

In forced convection, heat transfer depends mainly on

  1. Re, Pr
  2. Re, Gr
  3. mainly Gr
  4. Re only
Show the answer

Answer: A. Re, Pr

For laminar flow heat transfer in a pipe, the characteristic groups are

  1. Re, Gz
  2. Nu, Pr
  3. Nu, Pr, Re
  4. Nu, Gz
Show the answer

Answer: D. Nu, Gz

Velocity and thermal boundary layers over a heated plate are identical when Pr is

  1. 1
  2. <1
  3. >1
  4. none of these
Show the answer

Answer: A. 1

The Reynolds analogy states that

  1. St = f/2
  2. St = f/4
  3. St = 4f
  4. St = f^(1/2)
Show the answer

Answer: A. St = f/2

St = f/2 holds when the Prandtl number is

  1. 1.5
  2. 1
  3. >1
  4. <1
Show the answer

Answer: B. 1

Which fluid has the lowest Prandtl number?

  1. Liquid metal
  2. Aqueous solution
  3. Water
  4. Lube oil
Show the answer

Answer: A. Liquid metal

The Dittus–Boelter equation applies to

  1. for fluids in laminar flow.
  2. for fluids in tubulent flow.
  3. when Grashhoff number is very important.
  4. for liquid metals.
Show the answer

Answer: B. for fluids in tubulent flow.

The Colburn analogy is valid for Prandtl numbers of about

  1. 0.06 to 120
  2. 0.6 to 120
  3. 1 to 103
  4. 1 to 50
Show the answer

Answer: B. 0.6 to 120

Which form of the Colburn analogy is correct?

  1. jH = (St)(Pr)^(2/3) = f/2
  2. jH = (St)(Pr)^(1/3) = f/2
  3. jH = (St)^(2/3)(Pr) = f/2
  4. jH = (St)^(1/3)(Pr) = f/2
Show the answer

Answer: A. jH = (St)(Pr)^(2/3) = f/2

Which relation is correct?

  1. Nu = (Re)(Pr)(Gz)
  2. Nu = (Re)(Pr)(St)
  3. Nu = (Re)(Pr)
  4. Nu = (Pr)(St)
Show the answer

Answer: B. Nu = (Re)(Pr)(St)

For laminar flow through a very long tube where the outlet temperature approaches the wall temperature, use

  1. Nu = 0.023 Re^0.8 · Pr^0.4
  2. Nu = (π/2)Gz
  3. Nu = (2/π)Gz
  4. Nu = 2Gz^0.5
Show the answer

Answer: C. Nu = (2/π)Gz

For a fluid over a flat plate heated along its whole length, the average coefficient h_a and the local coefficient at the plate end h₁ are related by

  1. ha = h₁
  2. ha = 2h₁
  3. ha = 0.5 h₁
  4. ha = 0.75 h₁
Show the answer

Answer: B. ha = 2h₁

Frictional heating becomes significant compared with the heat exchanged when

  1. At high fluid velocity
  2. At low velocity
  3. When fluid flows past a smooth surface
  4. None of these
Show the answer

Answer: A. At high fluid velocity

The coefficient for film condensation is ____ that for dropwise condensation.

  1. greater than
  2. lower than
  3. is same as
  4. half
Show the answer

Answer: B. lower than

The Prandtl number is the ratio of

  1. momentum diffusivity to mass diffusivity.
  2. momentum diffusivity to thermal diffusivity.
  3. thermal diffusivity to mass diffusivity.
  4. thermal diffusivity to momentum diffusivity.
Show the answer

Answer: B. momentum diffusivity to thermal diffusivity.

The film coefficient between a condensing vapour and a wall increases with

  1. increasing temperature of the vapour.
  2. decreasing temperature of the vapour.
  3. increasing viscosity of the film of condensate.
  4. increasing temperature drop.
Show the answer

Answer: B. decreasing temperature of the vapour.

Dropwise condensation occurs on ____ surfaces.

  1. clean and dirt free
  2. smooth clean
  3. contaminated cooling
  4. polished
Show the answer

Answer: C. contaminated cooling

A non-condensable gas mixed with a condensing vapour

  1. increases the rate of condensation.
  2. decreases thermal resistance.
  3. is desirable to increase the film co-efficient.
  4. none of these.
Show the answer

Answer: D. none of these.

Film boiling is avoided in industrial equipment because

  1. the heat transfer rate is low in view of the large temperature drop.
  2. it is difficult to maintain.
  3. it is not economic.
  4. none of these.
Show the answer

Answer: A. the heat transfer rate is low in view of the large temperature drop.

In sub-cooled boiling,

  1. the heating surface is below the liquid’s boiling point.
  2. the heating surface is above the boiling point while the bulk liquid is below it.
  3. bubbles rise and escape to the vapour space.
  4. a very large vapour space is needed.
Show the answer

Answer: B. the heating surface is above the boiling point while the bulk liquid is below it.

Beyond the Leidenfrost point, heat flux rises again because

  1. convection becomes important
  2. conduction becomes important
  3. radiation becomes important
  4. sub-cooled boiling occurs
Show the answer

Answer: C. radiation becomes important

Nucleate boiling is promoted

  1. on polished surfaces
  2. on rough surfaces
  3. in the absence of agitation
  4. none of these
Show the answer

Answer: B. on rough surfaces

A black body has an emissivity of

  1. 1
  2. 0
  3. 0.90
  4. 0.5
Show the answer

Answer: A. 1

A black body has an absorptivity of

  1. 1
  2. 0
  3. 0.78
  4. 0.95
Show the answer

Answer: A. 1

The part of the spectrum important for radiant heat transfer is about ____ microns.

  1. 0.38-0.78
  2. 0.5-50
  3. 100-1000
  4. 5-50
Show the answer

Answer: B. 0.5-50

By Kirchhoff’s law, total emissive power divided by absorptivity depends on

  1. temperature of the body only.
  2. wavelength of monochromatic radiation.
  3. both (a) and (b).
  4. nature of material of body.
Show the answer

Answer: A. temperature of the body only.

Kirchhoff’s law applies to

  1. monochromatic radiation only
  2. total radiation only
  3. both (a) and (b)
  4. only volumes and not to surfaces
Show the answer

Answer: C. both (a) and (b)

The law saying the wavelength of peak emission is inversely proportional to absolute temperature is

  1. Stefan-Boltzman's
  2. Planck's
  3. Wien's displacement
  4. none of these
Show the answer

Answer: C. Wien's displacement

The solid angle that a finite surface subtends at a radiating element is called the

  1. called the view factor.
  2. called the angle of vision.
  3. proportional to the square of the distance between surfaces.
  4. expressed in terms of radians.
Show the answer

Answer: B. called the angle of vision.

Energy radiated by a surface at absolute temperature T varies as

  1. Q ∝ T²
  2. Q ∝ T⁴
  3. Q ∝ T³
  4. none of these
Show the answer

Answer: B. Q ∝ T⁴

Heat-sensitive materials are concentrated in evaporators operating under

  1. vacuum
  2. high pressure
  3. high residence time
  4. none of these
Show the answer

Answer: A. vacuum

Kilograms of water evaporated per kilogram of steam supplied is the evaporator’s

  1. capacity
  2. rate of evaporation
  3. economy
  4. rate of vaporisation
Show the answer

Answer: C. economy

Fruit juice is best concentrated in a ____ evaporator.

  1. long tube
  2. falling film
  3. high pressure
  4. none of these
Show the answer

Answer: B. falling film

The economy of a single-effect evaporator is

  1. 1
  2. <1
  3. >1
  4. none of these
Show the answer

Answer: B. <1

In a forward-feed multiple-effect evaporator,

  1. viscosity of liquid is highest in first effect.
  2. transfer from effect to effect is done by pumps.
  3. no pump is required to withdraw the product from the last effect.
  4. none of these.
Show the answer

Answer: D. none of these.

Kilograms of liquid evaporated per hour is the evaporator’s

  1. capacity
  2. economy
  3. steam load
  4. none of these
Show the answer

Answer: A. capacity

In a backward-feed multiple-effect evaporator,

  1. feed is introduced in the first effect.
  2. feed flows from low pressure to high pressure.
  3. no pumps are required between successive effects.
  4. none of these.
Show the answer

Answer: B. feed flows from low pressure to high pressure.

Evaporator economy is influenced by

  1. steam pressure
  2. feed temperature
  3. number of effect
  4. both (b) and (c)
Show the answer

Answer: D. both (b) and (c)

For a cold, viscous feed, backward feed gives

  1. a higher capacity
  2. a lower capacity
  3. lower economy
  4. none of these
Show the answer

Answer: A. a higher capacity

In a multiple-effect evaporator, boiling-point elevation mainly

  1. reduce the capacity
  2. reduce the economy
  3. increase the economy
  4. none of these
Show the answer

Answer: A. reduce the capacity

Which feed arrangement suits a cold viscous feed best?

  1. Forward feed
  2. Backward feed
  3. Mixed feed
  4. Parallel feed
Show the answer

Answer: B. Backward feed

Evaporators are run in multiple effect to obtain

  1. increased steam economy.
  2. decreased steam consumption.
  3. both (a) and (b).
  4. increased capacity.
Show the answer

Answer: C. both (a) and (b).

Raising the liquor level in an evaporator

  1. decreased capacity.
  2. increase in liquor film co-efficient.
  3. decreased effect of hydrostatic head.
  4. increased true temperature drop.
Show the answer

Answer: A. decreased capacity.

Lowering the feed temperature to an evaporator

  1. increases the heating area required.
  2. reduces the economy.
  3. both (a) and (b).
  4. decreases the heating area required.
Show the answer

Answer: C. both (a) and (b).

The true temperature drop across an evaporator’s heating surface depends on

  1. feed.
  2. depth of liquid over heating surface.
  3. pressure difference between steam chest and vapour space.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Expansion bellows are fitted in the shell of a tubular exchanger to

  1. increase the heating load.
  2. impart structural strength.
  3. account for the uneven expansion of shell and tube bundles.
  4. facilitate increase of shell length, if needed.
Show the answer

Answer: C. account for the uneven expansion of shell and tube bundles.

Multipass heat exchangers are used

  1. because of simplicity of fabrication,
  2. for low heat load.
  3. to obtain higher heat transfer co-efficient and shorter tube,
  4. to reduce the pressure drop.
Show the answer

Answer: C. to obtain higher heat transfer co-efficient and shorter tube,

Double-pipe exchangers are used

  1. when heat transfer area required is very high.
  2. when heat transfer area required is very low, i.e (100-200 ft²).
  3. because it occupies less floor area,
  4. because it is less costly.
Show the answer

Answer: B. when heat transfer area required is very low, i.e (100-200 ft²).

Finned-tube exchangers

  1. give larger area per tube.
  2. use metal fins of low thermal conductivity.
  3. facilitate very large temperature drop through tube wall.
  4. are used for smaller heat load.
Show the answer

Answer: A. give larger area per tube.

Shell-side baffles in a shell-and-tube exchanger

  1. increase the cross-section of the shell side liquid.
  2. force the liquid to flow parallel to the bank.
  3. increase the shell side heat transfer co-efficient.
  4. decrease the shell side heat transfer co-efficient.
Show the answer

Answer: C. increase the shell side heat transfer co-efficient.

In an exchanger, the heat transferred

  1. varies directly as the area and the LMTD.
  2. directly proportional to LMTD and inversely proportional to the area.
  3. varies as square of the area.
  4. none of these.
Show the answer

Answer: A. varies directly as the area and the LMTD.

In a shell-and-tube exchanger, temperature drops across the two films and the wall are

  1. the temperature drops in the two fluids and the wall are proportional to individual resistances.
  2. the temperature drop is inversely proportional to the resistance across which the drop occurs.
  3. there is no relationship between temperature drop and resistance.
  4. the relationship is not generalised.
Show the answer

Answer: A. the temperature drops in the two fluids and the wall are proportional to individual resistances.

Compared with triangular pitch, square tube pitch in a shell-and-tube exchanger

  1. gives a higher shell side pressure drop.
  2. gives a lower shell side pressure drop.
  3. can pack more surface area into a shell of given diameter.
  4. none of these.
Show the answer

Answer: B. gives a lower shell side pressure drop.

Regarding baffle spacing in a shell-and-tube exchanger,

  1. is not the same as baffle pitch.
  2. should be less than one fifth the diameter of the shell.
  3. should be less than the inside diameter of the shell.
  4. none of these.
Show the answer

Answer: C. should be less than the inside diameter of the shell.

Tube pitch is the ____ of the tube diameter and the clearance between tubes.

  1. sum
  2. difference
  3. ratio
  4. none of these
Show the answer

Answer: A. sum

Compared with parallel flow, counter-flow gives

  1. LMTD is greater.
  2. less surface area is required for a given heat transfer rate.
  3. both (a) and (b).
  4. more surface area is required for a given heat transfer rate.
Show the answer

Answer: C. both (a) and (b).

A 2-4 heat exchanger involves

  1. only counter-flow of fluids.
  2. only parallel-flow of fluids.
  3. both counter and parallel-flow of the fluids.
  4. smaller pressure drop compared to 1-2 exchanger.
Show the answer

Answer: C. both counter and parallel-flow of the fluids.

The floating head of a heat exchanger serves to

  1. avoid buckling of tubes.
  2. provide support for tubes.
  3. decrease the pressure drop.
  4. facilitate its lengthening, if needed.
Show the answer

Answer: A. avoid buckling of tubes.

In a finned (extended-surface) exchanger, the fluid with the lower film coefficient

  1. flows through the tube.
  2. flows outside the tubes.
  3. can flow either inside or outside the tubes.
  4. should not be used as it gives very high pressure drop.
Show the answer

Answer: B. flows outside the tubes.

A correction factor must be applied to the LMTD for ____ flow.

  1. parallel
  2. counter
  3. cross
  4. none of these
Show the answer

Answer: C. cross

For finned pipes, the equivalent diameter for pressure drop is ____ that for plain pipes of the same size.

  1. more
  2. less
  3. same
  4. unpredictable
Show the answer

Answer: B. less

A clean tube has overall coefficient U₁; with dirt on either side it is U₂. Then

  1. U₁ = U₂
  2. U₂ > U₁
  3. U₁ > U₂
  4. U₁ = dirt factor - U₂
Show the answer

Answer: C. U₁ > U₂

One transfer unit in a heat exchanger means

  1. a section of the exchanger in which change in temperature of one stream equals the average driving force in the section.
  2. the size of the exchanger in which heat transfer rate is 1 kcal/hr.
  3. both (a) and (b)
  4. none of these
Show the answer

Answer: A. a section of the exchanger in which change in temperature of one stream equals the average driving force in the section.

The heat conducted through a wall per unit time depends most directly on the

  1. Thickness of the wall.
  2. Area of the wall perpendicular to heat flow.
  3. Material of the wall,
  4. Temperature difference between the two surfaces of the wall.
Show the answer

Answer: D. Temperature difference between the two surfaces of the wall.

Water boils when its

  1. temperature reaches 100°C.
  2. vapour pressure equals 76 cm of Hg.
  3. saturated vapour pressure equals the external pressure on its surface.
  4. saturated vapour pressure is less than the atmospheric pressure.
Show the answer

Answer: C. saturated vapour pressure equals the external pressure on its surface.

The wavelength of maximum emission is inversely proportional to absolute temperature according to ____ law.

  1. Stefan's
  2. Dalton's
  3. Wien's
  4. Kirchoff's
Show the answer

Answer: C. Wien's

For concentrating Na₂SO₄ solution, whose solubility falls as temperature rises, the most suitable arrangement is a

  1. high pressure
  2. vacuum
  3. backward feed
  4. none of these
Show the answer

Answer: C. backward feed

The boiling-point elevation of NaOH solutions

  1. increases rapidly with temperature rise.
  2. is almost independent of temperature.
  3. is almost independent of pressure.
  4. both (b) and (c).
Show the answer

Answer: D. both (b) and (c).

The maximum water velocity in the tubes of a 1-2 exchanger is usually around ____ m/s.

  1. 1
  2. 10
  3. 20
  4. 30
Show the answer

Answer: A. 1

In a vertical-tube evaporator, raising the liquor level makes the overall coefficient

  1. increases
  2. decreases
  3. is not affected
  4. may increase or decrease; depends on the feed
Show the answer

Answer: B. decreases

In a vertical-tube evaporator, a higher liquor level

  1. capacity of the evaporator is decreased.
  2. capacity of the evaporator is increased,
  3. true temperature drop increases.
  4. both (b) and (c).
Show the answer

Answer: A. capacity of the evaporator is decreased.

In a vertical-tube evaporator, a higher liquor level increases

  1. velocity of circulation
  2. liquor-film co-efficient
  3. both (a) and (b)
  4. neither (a) and (b)
Show the answer

Answer: C. both (a) and (b)

The economy of a multiple-effect evaporator depends on

  1. heat balance consideration
  2. rate of heat transfer
  3. both (a) and (b)
  4. neither (a) nor (b)
Show the answer

Answer: C. both (a) and (b)

Compared with a single effect working over the same overall temperature difference, a double-effect evaporator mainly gives

  1. increased economy
  2. decreased economy
  3. lower capacity
  4. no effect on economy
Show the answer

Answer: A. increased economy

For a hot feed, forward feeding compared with backward feeding gives

  1. increased
  2. decreased
  3. no effect on
  4. none of these
Show the answer

Answer: A. increased

Vents are fitted on a condenser to

  1. remove non-condensable gases.
  2. purge the condenser.
  3. facilitate easy cleaning of tubes.
  4. none of these.
Show the answer

Answer: A. remove non-condensable gases.

A steam trap is used to

  1. condense the steam flowing in the pipeline.
  2. remove water resulting from partial condensation of steam.
  3. stop the supply of steam.
  4. none of these.
Show the answer

Answer: B. remove water resulting from partial condensation of steam.

The boiling-point elevation of an ideal solution

  1. increases rapidly with temperature rise.
  2. decreases rapidly with temperature rise.
  3. in independent of pressure.
  4. both (b) and (c).
Show the answer

Answer: A. increases rapidly with temperature rise.

Which fluid has the lowest Prandtl number?

  1. Molten sodium (a coolant used in fast breeder reactor)
  2. Water
  3. Transformer oil
  4. Dilute H₂SO₄
Show the answer

Answer: A. Molten sodium (a coolant used in fast breeder reactor)

Vaporisation taking place directly at the heating surface is called

  1. film boiling
  2. nucleate boiling
  3. vapour binding
  4. none of these
Show the answer

Answer: B. nucleate boiling

The rate of heat transfer by boiling from a pool of water depends on

  1. nature of heating surface and distribution of bubbles.
  2. surface tension of water.
  3. viscosity of water.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Equipment that converts the heat of one fluid into the latent heat of vaporisation of another is a

  1. boiler
  2. heat exchanger
  3. recuperator
  4. regenerator
Show the answer

Answer: A. boiler

In a parallel-flow exchanger, the lowest temperature the hot fluid can theoretically reach is

  1. equal to
  2. more than
  3. less than
  4. either more or less than (depending upon the fluid)
Show the answer

Answer: A. equal to

The LMTD is the same for counter-flow and parallel flow when

  1. cold fluid is heated to a certain temperature by condensing steam (isothermal fluid).
  2. outlent temperature of both the hot and cold fluid are same.
  3. outlet temperature of hot fluid is less than the outlet temperature of the cold fluid.
  4. none of these.
Show the answer

Answer: A. cold fluid is heated to a certain temperature by condensing steam (isothermal fluid).

1 BTU/h·ft²·°F equals about

  1. 1 kcal/hr. m².°C
  2. 4.88 kcal/hr. m².°C
  3. 1 kcal/hr. m².°K
  4. none of these.
Show the answer

Answer: B. 4.88 kcal/hr. m².°C

1 BTU/h·ft·°F equals about ____ kcal/h·m·°C.

  1. 1.49
  2. 1
  3. 4.88
  4. none of these
Show the answer

Answer: A. 1.49

In a multipass shell-and-tube exchanger, the return loss on the tube side is about ____ the velocity head per pass.

  1. twice
  2. four times
  3. square root of
  4. square of
Show the answer

Answer: B. four times

For natural convection from a vertical plate (laminar), the heat transfer rate varies with temperature difference as

  1. (ΔT)^(1/4)
  2. (ΔT)^(1/2)
  3. (ΔT)^(5/4)
  4. (ΔT)^(3/4)
Show the answer

Answer: C. (ΔT)^(5/4)

In a forward-feed multiple-effect evaporator, the pressure is

  1. highest in last effect
  2. lowest in last effect
  3. same in all effects
  4. dependent on the number of effects
Show the answer

Answer: B. lowest in last effect

For the same duty and tube-side flow, extra tube passes are used because they

  1. decreases the pressure drop.
  2. decreases the outlet temperature of cooling medium.
  3. increases the overall heat transfer coefficient.
  4. none of these.
Show the answer

Answer: C. increases the overall heat transfer coefficient.

A floating head is used in shell-and-tube exchangers for

  1. large temperature differentials.
  2. high heat transfer co-efficient.
  3. low pressure drop.
  4. less corrosion of tubes.
Show the answer

Answer: A. large temperature differentials.

For very heavy heat loads, the preferred arrangement is

  1. Double pipe
  2. Plate fine
  3. Series and parallel set of shell and tube
  4. None of these
Show the answer

Answer: C. Series and parallel set of shell and tube

Air is best heated by steam in a

  1. plate type.
  2. double pipe type with fins on steam side.
  3. double pipe type with fins on air side.
  4. shell and tube type.
Show the answer

Answer: C. double pipe type with fins on air side.

For evaporating a viscous solution in multiple effects, the preferred feed scheme is

  1. forward
  2. backward
  3. parallel
  4. none of these
Show the answer

Answer: B. backward

Steam gives the highest heat-transfer coefficient when it is

  1. supersaturated
  2. saturated
  3. wet
  4. none of these
Show the answer

Answer: B. saturated

Changing from one to two tube passes (same tubes, same flow) doubles the tube velocity. In turbulent flow, the pressure drop per unit length rises by about

  1. 1.8 times
  2. 2 times
  3. 3.5 times
  4. it stays the same
Show the answer

Answer: C. 3.5 times

Turning 1 kg of water at 0 °C into steam at 1 atm and 300 °C, most of the heat goes into

  1. heat the water from 0°C to 100 °C.
  2. evaporate the water.
  3. to superheat the steam.
  4. data insufficient, can't be predicted
Show the answer

Answer: B. evaporate the water.

To keep tube-side pressure drop low for a given flow, use a

  1. 1-2 heat exchanger
  2. 1-1 heat exchanger
  3. 3-2 heat exchanger
  4. 2-4 heat exchanger
Show the answer

Answer: B. 1-1 heat exchanger

Multiple-effect evaporators

  1. increase the steam economy and decrease the capacity.
  2. increase the steam economy and the capacity.
  3. decrease the steam economy and the capacity.
  4. decrease the steam economy and increase the capacity.
Show the answer

Answer: A. increase the steam economy and decrease the capacity.

A steam ejector is used to

  1. remove condensate from the steam pipelines.
  2. create vacuum.
  3. superheat the steam.
  4. none of these.
Show the answer

Answer: B. create vacuum.

The floating-head (pull-through bundle) design is used when

  1. in low range of temperature differences.
  2. in high range of temperature differences.
  3. because of its low cost.
  4. to prevent corrosion of the tube bundles.
Show the answer

Answer: B. in high range of temperature differences.

In a cooling tower, water is cooled mainly by

  1. loosing sensible heat.
  2. heat transfer to surroundings.
  3. vaporisation due to heat loss to air.
  4. loosing latent heat.
Show the answer

Answer: C. vaporisation due to heat loss to air.

Heat transfer rate = overall coefficient × temperature difference ×

  1. heating volume
  2. heat transfer area
  3. Nusselt number
  4. none of these
Show the answer

Answer: B. heat transfer area

A trap removes ____ from steam pipelines.

  1. steam
  2. condensate
  3. non-condensables
  4. none of these
Show the answer

Answer: B. condensate

An ejector is used to

  1. increase pressure
  2. increase temperature
  3. remove condensate
  4. none of these
Show the answer

Answer: D. none of these

When warm and cold liquids are mixed, heat moves mainly by

  1. internally
  2. convection
  3. radiation
  4. both (a) and (c)
Show the answer

Answer: B. convection

Small-scale evaporation is usually done in a

  1. heat exchanger
  2. condenser
  3. multiple effect evaporator
  4. steam jacketed kettle
Show the answer

Answer: D. steam jacketed kettle

Multiple-effect evaporation is used mainly for

  1. steam economy
  2. lower operating costs
  3. investment economy
  4. none of these
Show the answer

Answer: A. steam economy

The Dittus–Boelter equation should not be used for

  1. low Reynolds number
  2. very low Grashoff number
  3. molten metals
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

The Dittus–Boelter equation fails for liquid metals mainly because of their very low

  1. Prandtl number
  2. Grashoff number
  3. thermal conductivity
  4. viscosity
Show the answer

Answer: A. Prandtl number

The LMTD method cannot be used directly when

  1. U varies along the exchanger.
  2. the exchanger is in unsteady state.
  3. heat capacity varies with a phase change.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

The LMTD needs a correction factor for

  1. multipass heat exchanger.
  2. baffled heat exchanger.
  3. condensation of mixed vapour in a condenser.
  4. all (a) (b) and (c).
Show the answer

Answer: D. all (a) (b) and (c).

Evaporator tubes are generally

  1. horizontal
  2. vertical
  3. inclined
  4. random
Show the answer

Answer: B. vertical

The circulation pump of an evaporator is placed below it to

  1. avoid cavitation.
  2. avoid frequent priming.
  3. create more suction head.
  4. none of these.
Show the answer

Answer: A. avoid cavitation.

The SI unit of thermal conductivity is

  1. Watt/m. °K
  2. Watt/m³. °K
  3. Watt/m². °K
  4. Watt/m⁴. °K
Show the answer

Answer: A. Watt/m. °K

The SI unit of fouling factor is

  1. m² °K/W
  2. W/m² °K
  3. m² °KW
  4. m°k/W
Show the answer

Answer: A. m² °K/W

Thermal diffusivity matters most in heat transfer by

  1. conduction
  2. radiation
  3. condensation
  4. natural convection
Show the answer

Answer: A. conduction

The SI unit of heat-transfer coefficient is

  1. J/M²°K
  2. W/m² K
  3. W/m°K
  4. J/m K
Show the answer

Answer: B. W/m² K

Thermal conductance of a slab (thickness x, area A, conductivity K) is

  1. x/KA
  2. KA/x
  3. K/Ax
  4. A/Kx
Show the answer

Answer: B. KA/x

The Biot number is important in

  1. Transient heat conduction
  2. Natural convection
  3. Forced convection
  4. Radiation
Show the answer

Answer: A. Transient heat conduction

The geometric mean of areas A₁ and A₂ is

  1. √(A₁·A₂)
  2. √(A₁+A₂)
  3. (1/2)√(A₁·A₂)
  4. 2√(A₁·A₂)
Show the answer

Answer: A. √(A₁·A₂)

In nucleate boiling, heat flux varies with excess temperature as

  1. (ΔT)²
  2. (ΔT)⁴
  3. (ΔT)³
  4. √(ΔT)
Show the answer

Answer: C. (ΔT)³

Radiant heat transfer rate does NOT depend on the

  1. type of absorbing surface.
  2. distance between the heat source and the object receiving the heat.
  3. surface area and temperature of the heat source.
  4. none of these.
Show the answer

Answer: D. none of these.

Velocity and thermal boundary layers coincide when the Prandtl number is

  1. 0.5
  2. 1
  3. 1.5
  4. 80
Show the answer

Answer: B. 1

For laminar film condensation on a vertical surface, the average coefficient is inversely proportional to

  1. (ΔT)²
  2. √(ΔT)
  3. (ΔT)^(1/4)
  4. (ΔT)^(3/2)
Show the answer

Answer: C. (ΔT)^(1/4)

When Pr > 1, the thermal boundary layer

  1. is thicker than hydrodynamic boundary layer.
  2. is thinner than hydrodynamic boundary layer.
  3. and the hydrodynamic boundary layer are identical.
  4. disappears.
Show the answer

Answer: B. is thinner than hydrodynamic boundary layer.

The Stefan–Boltzmann constant in SI units is

  1. 5.6697 × 10⁻⁸ W/m². °K⁴
  2. 0.1714 × 10⁻⁸ W/m². °K⁴
  3. 5.6697 × 10⁻⁸ kcal/m². °K⁴
  4. 0.1714 × 10⁻⁸ kcal/m², °K⁴
Show the answer

Answer: A. 5.6697 × 10⁻⁸ W/m². °K⁴

At the very entrance of a tube, the tube-side heat-transfer coefficient is theoretically

  1. infinity.
  2. zero.
  3. same as average heat transfer co-efficient for tube side.
  4. none of these.
Show the answer

Answer: A. infinity.

For clean, non-fouling fluids, the best tube layout is

  1. Square pitch
  2. Triangnular pitch
  3. Diagonal square pitch
  4. None of these
Show the answer

Answer: B. Triangnular pitch

In a 1-1 co-current exchanger, if both outlet temperatures are equal, the LMTD is

  1. ∞
  2. 0
  3. equal to the difference between hot and cold fluids inlet temperature.
  4. equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature.
Show the answer

Answer: B. 0

The view factor matters in heat transfer by

  1. steady state conduction
  2. natural convection
  3. forced convection
  4. radiation
Show the answer

Answer: D. radiation

For the same terminal temperatures, LMTD (parallel flow) divided by LMTD (counter-flow) is always

  1. <1
  2. >1
  3. 1
  4. ∞
Show the answer

Answer: A. <1

For a perfect black body, absorptivity and reflectivity are

  1. 1 and 0
  2. 0 and 1
  3. 1 and ∞
  4. 0 and 0.5
Show the answer

Answer: A. 1 and 0

“At thermal equilibrium, emissive power divided by absorptivity is the same for all bodies” is ____ law.

  1. Kirchhoffs
  2. Planck's
  3. Wien's displacement
  4. Stefan-Boltzman
Show the answer

Answer: A. Kirchhoffs

As temperature rises, the thermal conductivity of a gas

  1. increases.
  2. decreases.
  3. remains same.
  4. may increase or decrease depending on the type of gas.
Show the answer

Answer: A. increases.

A perfect insulator would have a thermal conductivity of

  1. 0
  2. 1
  3. ∞
  4. between 0 and ∞
Show the answer

Answer: A. 0

A body is grey when its monochromatic emissivity is

  1. zero
  2. unity
  3. same for all wavelengths
  4. different for all wavelengths
Show the answer

Answer: C. same for all wavelengths

The monochromatic emissive power of a black body is given by

  1. Planck's law
  2. Kirchhoffs law
  3. Wien's law
  4. Stefan-Boltzman law
Show the answer

Answer: A. Planck's law

For a given tube outside diameter, a higher BWG number means a larger

  1. tube thickness
  2. cross-sectional area
  3. weight per unit length
  4. none of these
Show the answer

Answer: B. cross-sectional area

Dühring’s rule is used in problems on

  1. distillation
  2. crystallisation
  3. evaporation
  4. humidification
Show the answer

Answer: C. evaporation

Most dry gases have a Prandtl number of about

  1. 0.001
  2. 0.72
  3. 70
  4. 150
Show the answer

Answer: B. 0.72

By the Reynolds analogy, the Stanton number equals

  1. 2f
  2. f
  3. f/2
  4. f/4
Show the answer

Answer: C. f/2

The Graetz number relates to

  1. mass transfer between a gas and a liquid.
  2. absorption with chemical reaction.
  3. heat transfer in turbulent flow.
  4. heat transfer in laminar flow.
Show the answer

Answer: D. heat transfer in laminar flow.

Kinematic viscosity divided by thermal diffusivity is the ____ number.

  1. Peclet
  2. Prandtl
  3. Stanton
  4. Nusselt
Show the answer

Answer: B. Prandtl

The product of Grashof and Prandtl numbers is the ____ number.

  1. Graetz
  2. Reyleigh
  3. Nusselt
  4. Stanton
Show the answer

Answer: B. Reyleigh

St·Pr^(2/3) = f/2 is the

  1. Colburn
  2. Reynolds
  3. Prandtl
  4. none of these
Show the answer

Answer: A. Colburn

St = f/2 is the

  1. Colburn
  2. Reynolds
  3. Prandtl
  4. none of these
Show the answer

Answer: B. Reynolds

The Prandtl and Reynolds analogies coincide when Pr equals

  1. 0.5
  2. 1
  3. >2
  4. 1.5
Show the answer

Answer: B. 1

The Colburn analogy holds for Prandtl numbers of about

  1. 0.001 to 1
  2. 0.6 to 120
  3. 0.5 to 5
  4. 120 to 400
Show the answer

Answer: B. 0.6 to 120

For laminar film condensation on a vertical surface, the local coefficient varies with film thickness t as

  1. ∞t
  2. ∞(1/t)
  3. ∞√t
  4. independent of t
Show the answer

Answer: B. ∞(1/t)

The peak heat flux on a boiling curve is called the

  1. Nusselt
  2. Leidenfrost
  3. boiling
  4. burnout
Show the answer

Answer: D. burnout

The Stefan–Boltzmann constant depends on

  1. medium
  2. temperature
  3. surface
  4. none of these
Show the answer

Answer: D. none of these

Electromagnetic radiation travels through vacuum at about ____ m/s.

  1. 3 × 10⁵
  2. 3 × 10⁸
  3. 3 × 10¹⁰
  4. 3 × 10¹²
Show the answer

Answer: B. 3 × 10⁸

The controlling film coefficient is the one with

  1. no
  2. the least
  3. the largest
  4. lower
Show the answer

Answer: C. the largest

Oil being chilled for dewaxing is usually cooled in a ____ exchanger.

  1. U-tube
  2. Double pipe
  3. Fixed tube
  4. Floating head
Show the answer

Answer: A. U-tube

When the shell-side fluid is much hotter than the tube-side fluid, the most suitable exchanger is

  1. Single pass, fixed tube sheet
  2. U-tube
  3. Three pass, fixed tube sheet
  4. none of these
Show the answer

Answer: B. U-tube

A longitudinal baffle across the shell makes the shell-side fluid pass through the exchanger

  1. once
  2. twice
  3. thrice
  4. four times
Show the answer

Answer: B. twice

Steam traps on steam lines

  1. condense steam.
  2. release excess steam pressure by bleeding steam.
  3. remove condensate and inert gases.
  4. none of these.
Show the answer

Answer: C. remove condensate and inert gases.

Which is suitable for concentrating a very concentrated solution?

  1. Open pan evaporation
  2. Long tube vertical evaporator
  3. Agitated film evaporator
  4. None of these
Show the answer

Answer: A. Open pan evaporation

Viscous, heat-sensitive liquids are concentrated in ____ evaporators.

  1. open pan
  2. long tube
  3. agitated film
  4. none of these
Show the answer

Answer: C. agitated film

By Dühring’s rule, a solution’s boiling point is a linear function of the ____ of water.

  1. boiling point (at the same pressure)
  2. viscosity
  3. density
  4. thermal conductivity
Show the answer

Answer: A. boiling point (at the same pressure)

Superheated steam is not preferred in evaporators because of its very

  1. high temperature
  2. high pressure
  3. low film co-efficient
  4. none of these
Show the answer

Answer: C. low film co-efficient

The true temperature drop across an evaporator’s heating surface depends on

  1. liquid depth over the heating surface.
  2. solution being evaporated.
  3. pressure difference between the steam chest and the vapor space above the boiling liquid.
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

The steam-side coefficient in an evaporator is typically ____ kcal/h·m²·°C.

  1. 10-50
  2. 100-500
  3. 1000-1500
  4. 5000-15000
Show the answer

Answer: C. 1000-1500

Crystals can form only in a ____ solution.

  1. saturated
  2. supersaturated
  3. undersaturated
  4. all (a), (b) and (c)
Show the answer

Answer: B. supersaturated

Transverse baffles in a shell-and-tube exchanger increase

  1. rate of heat transfer.
  2. flow velocity.
  3. turbulence of shell side fluid.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Tube vibration in a shell-and-tube exchanger can be caused by

  1. flow of fluid on the tube and shell sides.
  2. oscillations in the flow of shell/tube sides fluid.
  3. vibrations transmitted through piping and/or supports due to external reasons.
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

Shell-and-tube exchangers are preferred when a large heat-transfer area is needed because they

  1. occupies smaller space.
  2. is more economical.
  3. is easy to operate and maintain.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

For a black body, the wavelength of peak monochromatic emissive power is proportional to

  1. T
  2. 1/T
  3. T⁴
  4. it does not depend on T
Show the answer

Answer: B. 1/T

As temperature rises, the total emissivity of metallic conductors

  1. increases
  2. decreases
  3. remains same
  4. decreases linearly
Show the answer

Answer: A. increases

Which paint has the highest absorptivity?

  1. Black
  2. Yellow
  3. White
  4. Grey
Show the answer

Answer: A. Black

Which paint has the lowest absorptivity?

  1. Black
  2. White lead
  3. Grey
  4. Light cream
Show the answer

Answer: B. White lead

As the distance between a heat source and the receiving object increases, radiant heat transfer

  1. decreases
  2. increases
  3. increases exponentially
  4. remains unaffected
Show the answer

Answer: A. decreases

In laminar film condensation on a vertical surface, the film thickness from top to bottom

  1. cumulatively increases
  2. cumulatively decreases
  3. remains constant
  4. and the surface conductance increase
Show the answer

Answer: A. cumulatively increases

In India, common salt is produced from sea water mainly by

  1. freeze drying
  2. solar evaporation
  3. electrolytic
  4. none of these
Show the answer

Answer: B. solar evaporation

All three modes of heat transfer occur together in a

  1. condensation of steam in a partial condenser.
  2. boiler furnace.
  3. insulated pipe carraying high pressure steam.
  4. none of these.
Show the answer

Answer: B. boiler furnace.

Which boiler fitting protects it when the water level falls too low?

  1. Blow down valve
  2. Blow off cock
  3. Fusible plug
  4. Safety valve
Show the answer

Answer: C. Fusible plug

Refrigerated transport of food over long distances commonly uses

  1. ice
  2. liquid nitrogen
  3. liquid oxygen
  4. vacuum evaporation
Show the answer

Answer: B. liquid nitrogen

For condenser tubes cooled by brine (salt water), the best material is

  1. Aluminium
  2. Copper
  3. Titanium
  4. Stainless steel
Show the answer

Answer: C. Titanium

Fins are most useful in boiling when the surface is in the ____ boiling regime.

  1. film
  2. nucleate
  3. transition
  4. all modes of
Show the answer

Answer: B. nucleate

At any temperature, the most radiation at every wavelength is emitted by a ____ body.

  1. grey
  2. black
  3. opaque
  4. white
Show the answer

Answer: B. black

Moist air passing over a dry cold coil without any condensation is cooled at constant

  1. enthalpy
  2. relative humidity
  3. wet bulb temperature
  4. dew point temperature
Show the answer

Answer: D. dew point temperature

A syphon loop is placed before a pressure gauge on a steam line to

  1. avoid the overheating of the tubes & bellows which operate them to minimise error and damage.
  2. form a seal of water by steam condensate to fill the tube or bellows at the pressure being measured,
  3. both a and b.
  4. avoid the static head error introduced by steam entry.
Show the answer

Answer: C. both a and b.

Which pairs are correctly matched?

  1. Heat transfer: Thermal diffusivity.
  2. Mass transfer: Diffusion co-efficient.
  3. Momentum transfer: Kinematic viscosity.
  4. all a, b & c are correctly matched.
Show the answer

Answer: D. all a, b & c are correctly matched.

Compared with non-metals, metals generally have high thermal

  1. conductivity
  2. diffusivity
  3. inertia
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

The rivet diameter for a 20 mm thick boiler plate is about ____ mm.

  1. 10
  2. 20
  3. 30
  4. 40
Show the answer

Answer: C. 30

Which of these conducts electricity worst?

  1. Carbon
  2. Aluminium
  3. Silver
  4. Stainless steel
Show the answer

Answer: A. Carbon

The general quality of water is commonly judged first by its

  1. pH value.
  2. electrical conductivity.
  3. turbidity.
  4. dissolved oxygen content.
Show the answer

Answer: A. pH value.

As temperature rises, electrical conductivity increases for a

  1. semi-conductor
  2. metal or alloy
  3. dielectric
  4. none of these
Show the answer

Answer: A. semi-conductor

Evaporative cooling in a cooling tower can theoretically cool water down to the ____ temperature of the air.

  1. wet bulb
  2. dry bulb
  3. saturation
  4. dew point
Show the answer

Answer: A. wet bulb

Thermal diffusivity is proportional to

  1. 1/k
  2. k
  3. k²
  4. 1/k²
Show the answer

Answer: B. k

Radiation falling on a black body is entirely

  1. refracted
  2. reflected
  3. transmitted
  4. absorbed
Show the answer

Answer: D. absorbed

Which property of air does NOT increase as its temperature rises?

  1. Density
  2. Thermal diffusivity
  3. Viscosity
  4. Thermal conductivity
Show the answer

Answer: A. Density

Which of these transfers the least heat?

  1. Boiling.
  2. Forced convection in air.
  3. free convection in air.
  4. Conduction in air.
Show the answer

Answer: D. Conduction in air.

The tail pipe of a barometric condenser must be longer than the Torricellian height of water, about ____ m.

  1. 1
  2. 5
  3. 34
  4. 10
Show the answer

Answer: D. 10

As temperature rises, the electrical conductivity of a semiconductor

  1. increases.
  2. decreases.
  3. remain constant.
  4. either (a) or (b), depends on the type of semi-conductor.
Show the answer

Answer: A. increases.

Oxygen in flue gas is measured by an analyser based on

  1. Chemical absorption.
  2. Thermal conductivity.
  3. Infrared absorption.
  4. Paramagnetism.
Show the answer

Answer: D. Paramagnetism.

A drawback of water as a manometer fluid is its

  1. low vapour pressure.
  2. corrosive nature.
  3. high vapour pressure.
  4. high boiling point.
Show the answer

Answer: C. high vapour pressure.

Which condenser-tube material has the lowest thermal conductivity?

  1. Admirability brass.
  2. Stainless steel.
  3. Aluminium brass.
  4. Titanium.
Show the answer

Answer: B. Stainless steel.

Baffle width is usually about ____ of the tank diameter.

  1. 0.1-0.12
  2. 0.4-0.5
  3. 0.45-0.6
  4. 0.2-0.45
Show the answer

Answer: A. 0.1-0.12

The minimum baffle height should be about

  1. equal to the impeller diameter.
  2. twice the impeller diameter.
  3. twice the tank diameter.
  4. 3/4 of the tank height.
Show the answer

Answer: B. twice the impeller diameter.

Baffles can be omitted when agitating

  1. low viscosity liquids (< 200 poise).
  2. high viscosity liquids (> 600 poise).
  3. large diameter tanks.
  4. none of these.
Show the answer

Answer: B. high viscosity liquids (> 600 poise).

The LMTD of a shell-and-tube exchanger

  1. is always less than arithmetic average value.
  2. is always more than arithmetic mean value and the geometric mean value.
  3. is always less than arithmetic mean value, but more than geometric mean value.
  4. may be either more or less than geometric mean and arithmetic mean value.
Show the answer

Answer: C. is always less than arithmetic mean value, but more than geometric mean value.

In a double-pipe exchanger, the hydraulic (equivalent) diameter of the annulus for heat transfer is

  1. same as that for fluid flow.
  2. less than that for fluid flow.
  3. more than that for fluid flow.
  4. D₂ - D₁ (D₁ and D₂ are I.D. of inner and outer pipes respectively).
Show the answer

Answer: C. more than that for fluid flow.

A fouling factor must be included in design especially when the liquid

  1. containing suspended solids flows at low velocity.
  2. containing suspended solids flows at high velocity.
  3. is highly viscous.
  4. is of high specific gravity.
Show the answer

Answer: A. containing suspended solids flows at low velocity.

The fouling factor depends on the

  1. characteristic of process fluid.
  2. velocity of process fluid containing suspended solids.
  3. suspended solids in the fluid.
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

Floating-head exchangers are chosen when

  1. heat transfer between corrosive fluids.
  2. cases where temperature difference between the shell and the tubes is more (>50°C).
  3. co-current heat transfer systems.
  4. counter-current heat transfer systems.
Show the answer

Answer: B. cases where temperature difference between the shell and the tubes is more (>50°C).

The shortest centre-to-centre distance between adjacent tubes is the

  1. called tube pitch.
  2. called tube clearance.
  3. always less than the diameter of the tube.
  4. none of these.
Show the answer

Answer: A. called tube pitch.

The shortest gap between the walls of two adjacent tubes is the

  1. called tube pitch.
  2. called tube clearance.
  3. more in case of triangular pitch as compared to square pitch of tube layout.
  4. none of these.
Show the answer

Answer: B. called tube clearance.

In most shell-and-tube exchangers, tube pitch is about ____ the tube diameter.

  1. less than
  2. 1.25-1.50 times
  3. 2.5 times
  4. one-fourth of
Show the answer

Answer: B. 1.25-1.50 times

A triangular-pitch tube layout

  1. permits the use of less tubes in a given shell diameter.
  2. facilitates comparatively easier external cleaning because of large clearance.
  3. permits the use of more tubes in a given shell diameter.
  4. both (b) and (c).
Show the answer

Answer: C. permits the use of more tubes in a given shell diameter.

A “25 % cut” segmental baffle has a height of

  1. height is 75% of the I.D. of the shell.
  2. height is 25% of the I.D. of the shell.
  3. spacing is 75% of its height.
  4. width is 25% of its height.
Show the answer

Answer: A. height is 75% of the I.D. of the shell.

Straight tie rods in a shell-and-tube exchanger

  1. hold baffle in space.
  2. fix the tubes in position.
  3. account for thermal strain.
  4. none of these.
Show the answer

Answer: A. hold baffle in space.

Baffle spacing is usually

  1. more than
  2. not greater than
  3. not less than one fifth of
  4. both (b) and (c)
Show the answer

Answer: D. both (b) and (c)

The most common baffle in industrial shell-and-tube exchangers is the

  1. 75% cut segmental baffle.
  2. 25% cut segmental baffle.
  3. Orifice baffle.
  4. Disk and doughnut baffle.
Show the answer

Answer: B. 25% cut segmental baffle.

ASME Section VIII is used for:

  1. Storage tanks
  2. Design of pressure vessels (Division 1
  3. Heat exchanger design
  4. Piping design
Show the answer

Answer: B. Design of pressure vessels (Division 1 Design of pressure vessels (Division 1: standard, Division 2: alternative rules)

Shell thickness of cylindrical vessel (hoop stress) by ASME:

  1. None
  2. t = PD/2S
  3. t = P/SE
  4. t = PR/ where P=pressure, R=radius, S=allowable stress, E=joint efficiency
Show the answer

Answer: D. t = PR/ where P=pressure, R=radius, S=allowable stress, E=joint efficiency t = PR/(SE − 0.6P) where P=pressure, R=radius, S=allowable stress, E=joint efficiency

Hemispherical head:

  1. Same as flat
  2. Weakest
  3. None
  4. Strongest head shape (t = PR/2SE
Show the answer

Answer: D. Strongest head shape (t = PR/2SE Strongest head shape (t = PR/2SE - half the shell thickness needed)

Flat head thickness is:

  1. None
  2. Much greater than cylindrical shell (t = d√)
  3. Same as shell
  4. Less than shell
Show the answer

Answer: B. Much greater than cylindrical shell (t = d√) Much greater than cylindrical shell (t = d√(CP/SE)) - not efficient

TEMA standard governs:

  1. Plate heat exchangers
  2. Fired heaters
  3. Shell and tube heat exchanger design and materials
  4. Air coolers
Show the answer

Answer: C. Shell and tube heat exchanger design and materials Shell and tube heat exchanger (STHEx) design and materials

TEMA designations R, C, B:

  1. R = severe service; C = commercial; B = chemical process
  2. None
  3. Only for tube size
  4. Only for materials
Show the answer

Answer: A. R = severe service; C = commercial; B = chemical process R = severe service (refinery); C = commercial; B = chemical process - different tolerances

Log Mean Temperature Difference (LMTD):

  1. None
  2. Maximum difference
  3. Driving force for heat transfer
  4. Arithmetic mean
Show the answer

Answer: C. Driving force for heat transfer Driving force for heat transfer: ΔTlm = (ΔT1 − ΔT2) / ln(ΔT1/ΔT2)

LMTD correction factor F:

  1. None
  2. Accounts for multi-pass or cross-flow; F < 1 for non-pure counterflow
  3. Always 1
  4. Greater than 1
Show the answer

Answer: B. Accounts for multi-pass or cross-flow; F < 1 for non-pure counterflow Accounts for multi-pass or cross-flow (Q = U·A·F·ΔTlm); F < 1 for non-pure counterflow

Overall heat transfer coefficient U:

  1. None
  2. U = hi + ho
  3. U = hi × ho
  4. 1/U = 1/hi + fouling_i + t_w/k_w + fouling_o + 1/ho
Show the answer

Answer: D. 1/U = 1/hi + fouling_i + t_w/k_w + fouling_o + 1/ho

Fouling factor (resistance):

  1. None
  2. Increases U
  3. No effect
  4. Additional thermal resistance due to deposits on heat transfer surfaces; reduces U
Show the answer

Answer: D. Additional thermal resistance due to deposits on heat transfer surfaces; reduces U

Number of Transfer Units (NTU) method:

  1. For gas only
  2. Used when outlet temperatures unknown; NTU = UA/C_min
  3. Same as LMTD
  4. None
Show the answer

Answer: B. Used when outlet temperatures unknown; NTU = UA/C_min

Effectiveness ε of heat exchanger:

  1. ε = LMTD/ΔTmax
  2. ε = actual heat transfer / maximum possible heat transfer
  3. None
  4. ε = U·A
Show the answer

Answer: B. ε = actual heat transfer / maximum possible heat transfer

API 653:

  1. Above-ground storage tank inspection, repair, alteration, and reconstruction standard
  2. Pressure vessel
  3. Piping
  4. Exchanger
Show the answer

Answer: A. Above-ground storage tank inspection, repair, alteration, and reconstruction standard

Clad plate vessels:

  1. None
  2. Thick carbon steel shell with thin corrosion-resistant lining
  3. No lining
  4. Solid alloy only
Show the answer

Answer: B. Thick carbon steel shell with thin corrosion-resistant lining Thick carbon steel shell with thin corrosion-resistant lining (SS, Ti) - cost-effective vs solid alloy

Heat exchanger types beyond shell-and-tube:

  1. Only shell-and-tube
  2. Plate-and-frame, spiral, air cooler, double pipe, plate-fin
  3. Only plate
  4. None
Show the answer

Answer: B. Plate-and-frame, spiral, air cooler, double pipe, plate-fin Plate-and-frame, spiral, air cooler (fin-fan), double pipe, plate-fin - different applications

Plate heat exchanger advantage:

  1. None
  2. Lower efficiency
  3. Larger footprint
  4. High heat transfer coefficient, compact, easy cleaning; limit
Show the answer

Answer: D. High heat transfer coefficient, compact, easy cleaning; limit High heat transfer coefficient, compact, easy cleaning; limit: lower pressure/temperature rating

Air-cooled heat exchanger (fin-fan cooler):

  1. None
  2. Water-cooled only
  3. Finned tubes cooled by air flow from fans
  4. Less efficient always
Show the answer

Answer: C. Finned tubes cooled by air flow from fans Finned tubes cooled by air flow from fans - used where cooling water not available/expensive

Tube vibration in shell-and-tube HX:

  1. None
  2. Acoustic or flow-induced vibration can damage tubes
  3. Always occurs
  4. Not a concern
Show the answer

Answer: B. Acoustic or flow-induced vibration can damage tubes Acoustic or flow-induced vibration can damage tubes - checked by TEMA or HTFS methods

Process heater tube metallurgy:

  1. Always carbon steel
  2. None
  3. Always stainless
  4. Selected based on max tube skin T and fluid
Show the answer

Answer: D. Selected based on max tube skin T and fluid Selected based on max tube skin T and fluid - carbon steel, Cr-Mo, SS, high-alloy

Tube skin temperature in fired heater:

  1. Must stay below creep/oxidation limit
  2. None
  3. Only average T
  4. Not important
Show the answer

Answer: A. Must stay below creep/oxidation limit Must stay below creep/oxidation limit - monitored by infrared or thermocouple

Vessel nozzle load analysis:

  1. Only visual check
  2. None
  3. WRC 297 or FEA evaluates stresses at nozzle-shell junction from piping loads
  4. Not required
Show the answer

Answer: C. WRC 297 or FEA evaluates stresses at nozzle-shell junction from piping loads

Shell and tube HX - tube count:

  1. Not calculated
  2. None
  3. Random
  4. Calculated from tube layout and bundle diameter
Show the answer

Answer: D. Calculated from tube layout and bundle diameter Calculated from tube layout (triangular or square pitch) and bundle diameter

Triangular vs square tube pitch:

  1. Triangular
  2. Square always better
  3. None
  4. No difference
Show the answer

Answer: A. Triangular Triangular: more tubes per shell, better heat transfer; Square: easier mechanical cleaning

Number of tube passes:

  1. More passes → higher tube-side velocity → better h but higher pressure drop
  2. None
  3. Always 4 passes
  4. Always 1 pass
Show the answer

Answer: A. More passes → higher tube-side velocity → better h but higher pressure drop More passes → higher tube-side velocity → better h but higher pressure drop - trade-off

TEMA shell types:

  1. Only K type
  2. Only E type
  3. None
  4. E, F, G, H, J, K, X
Show the answer

Answer: D. E, F, G, H, J, K, X E (most common, single pass shell), F (two pass), G (split flow), H (double split), J (divided flow), K (kettle), X (cross flow)

Impingement plate in HX shell inlet:

  1. None
  2. Protects tube bundle from erosion/vibration due to high velocity inlet stream
  3. Only for gases
  4. Decorative
Show the answer

Answer: B. Protects tube bundle from erosion/vibration due to high velocity inlet stream

Finned tube heat exchanger - fin efficiency:

  1. η
  2. [
  3. _
  4. "
Show the answer

Answer: B. [

U-tube heat exchanger advantage:

  1. A
  2. "
  3. [
  4. l
Show the answer

Answer: C. [

Fixed tube sheet HX limitation:

  1. i
  2. "
  3. [
  4. D
Show the answer

Answer: C. [

Double pipe heat exchanger:

  1. "
  2. [
  3. S
  4. i
Show the answer

Answer: B. [

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →