IITIAN1997 STUDIO

Industrial chemical process I–III (Ch-402, Ch-502, Ch-602)

JLEE CHE · 1004 practice questions with answers

Practise and take a mock test →

Manufacture of important chemicals

Topics: Soda ash (Solvay), caustic soda and chlorine (membrane cell), sulphuric acid (contact process), nitric acid (Ostwald), ammonia (Haber), urea, phosphatic fertilisers, cement, glass, paper and pulp (kraft), sugar, soaps and detergents, oils and fats (hydrogenation), fermentation (ethanol).

Heavy inorganic chemicals: soda ash, caustic soda, sulphuric acid

Soda ash (Na₂CO₃) is made by the Solvay process: brine is saturated with ammonia and carbonated, sodium bicarbonate precipitates and is calcined; ammonia is recovered with lime. Caustic soda and chlorine come from electrolysis of brine, now in membrane cells (mercury cells were phased out).

Sulphuric acid by the contact process: S burnt to SO₂; 2SO₂ + O₂ ⇌ 2SO₃ over V₂O₅ at about 400–450 °C; SO₃ is absorbed in 98 % acid, not water, because water forms an acid mist.

  • Solvay: brine + NH₃ + CO₂ → NaHCO₃ → Na₂CO₃
  • Chlor-alkali: membrane cell
  • Contact: V₂O₅, 400–450 °C, absorb in 98 % acid

Example: Why is SO₃ absorbed in 98 % sulphuric acid rather than water?

  1. SO₃ reacts violently with water and forms a fine acid mist that escapes.
  2. Concentrated acid absorbs it smoothly, giving oleum or stronger acid.

Answer: To avoid acid mist

Example: How many tonnes of H₂SO₄ can 1 t of sulphur make (100 % conversion)?

  1. S (32) → H₂SO₄ (98).
  2. 98/32 ≈ 3.06 t.

Answer: ≈ 3.06 t

Ammonia, nitric acid and urea

Haber process: N₂ + 3H₂ ⇌ 2NH₃, exothermic (ΔH ≈ −92 kJ), favoured by high pressure (150–300 bar) and low temperature, but run at about 400–500 °C on an iron catalyst for a useful rate (Le Chatelier versus kinetics).

Nitric acid (Ostwald): ammonia is oxidised over Pt–Rh gauze to NO, then to NO₂, absorbed in water. Urea: 2NH₃ + CO₂ → ammonium carbamate → urea + water, at high pressure.

  • Haber: Fe catalyst, 150–300 bar, 400–500 °C
  • Ostwald: Pt–Rh gauze
  • Urea N content 46.7 %

Example: Find the nitrogen content of urea, CO(NH₂)₂ (M = 60).

  1. Nitrogen = 2 × 14 = 28.
  2. 28/60 = 46.7 %.

Answer: 46.7 %

Example: How much ammonia is needed per tonne of urea (stoichiometric)?

  1. 2 NH₃ (34) per urea (60).
  2. 34/60 ≈ 0.567 t.

Answer: ≈ 0.57 t

Cement, glass, paper, sugar, soaps and fermentation

Cement: limestone and clay are ground and burnt in a rotary kiln at about 1450 °C to clinker, then ground with gypsum (which controls setting). Glass is fused silica with soda ash and lime. Paper: wood or bamboo pulp (kraft process) formed into sheets. Sugar: cane juice clarified, evaporated and crystallised.

Soaps: fats + NaOH → soap + glycerol (saponification). Hydrogenation hardens oils into vanaspati using a nickel catalyst. Fermentation: yeast turns glucose into ethanol and CO₂.

  • Kiln ≈ 1450 °C; gypsum controls setting
  • Saponification gives soap + glycerol
  • C₆H₁₂O₆ → 2C₂H₅OH + 2CO₂

Example: Find the maximum mass of ethanol from 180 kg of glucose.

  1. C₆H₁₂O₆ (180) → 2C₂H₅OH (2 × 46 = 92).
  2. 92 kg (51 % by mass).

Answer: 92 kg

Example: Why is gypsum added to cement clinker?

  1. Without it, tricalcium aluminate reacts at once and the paste sets in minutes (flash set).
  2. Gypsum slows this, giving workable setting time.

Answer: To control setting

The contact process oxidises SO₂ to SO₃ over V₂O₅ at about 450 °C and absorbs SO₃ in 98% acid (not water, which forms a mist). Ammonia is made by the Haber process over an iron catalyst (promoted by K₂O and Al₂O₃) at about 450 °C and 150–300 atm; ammonia and CO₂ give urea through ammonium carbamate. Nitric acid comes from catalytic oxidation of ammonia over Pt–Rh gauze (Ostwald). The Solvay process makes Na₂CO₃ from brine, NH₃ and CO₂, recovering ammonia with lime. Cement clinker is burned at about 1450 °C in a rotary kiln; gypsum is added to retard setting. Kraft pulping uses NaOH + Na₂S (white liquor). Oils are hardened by hydrogenation over nickel; soap is made by saponification of fats with NaOH.

  • V₂O₅ catalyst — H₂SO₄; Fe catalyst — NH₃; Pt–Rh — HNO₃; Ni — hydrogenation.
  • Oleum = SO₃ dissolved in H₂SO₄.
  • Main cement compounds: C₃S, C₂S, C₃A, C₄AF.
  • Urea has 46% nitrogen.
  • Yeast ferments sugar to ethanol (about 8–12% in the wash), concentrated by distillation.

Key formulas

  • 2SO₂ + O₂ ⇌ 2SO₃ (V₂O₅)
  • N₂ + 3H₂ ⇌ 2NH₃ (Fe)
  • 4NH₃ + 5O₂ → 4NO + 6H₂O (Pt–Rh)
  • C₆H₁₂O₆ → 2C₂H₅OH + 2CO₂

Practice questions

The catalyst in the contact process is

  1. Fe
  2. V₂O₅
  3. Pt–Rh
  4. Ni
Show the answer

Answer: B. V₂O₅ Vanadium pentoxide.

SO₃ is absorbed in

  1. water
  2. 98% H₂SO₄
  3. dilute H₂SO₄
  4. NaOH
Show the answer

Answer: B. 98% H₂SO₄ Avoids acid mist.

The Haber process uses a catalyst of

  1. iron
  2. nickel
  3. platinum
  4. vanadium
Show the answer

Answer: A. iron Promoted iron.

Nitric acid is made by the

  1. Solvay process
  2. Ostwald process
  3. contact process
  4. Haber process
Show the answer

Answer: B. Ostwald process Ammonia oxidation.

Gypsum is added to cement to

  1. increase strength
  2. retard setting
  3. colour it
  4. reduce cost only
Show the answer

Answer: B. retard setting Controls flash set of C₃A.

The nitrogen content of urea is about

  1. 21%
  2. 46%
  3. 82%
  4. 35%
Show the answer

Answer: B. 46% 28/60.

White liquor in kraft pulping is

  1. NaOH + Na₂S
  2. Na₂CO₃ + NaCl
  3. H₂SO₄
  4. Ca(HSO₃)₂
Show the answer

Answer: A. NaOH + Na₂S Sulphate process.

Soda ash is manufactured by the

  1. Solvay process
  2. Leblanc process only
  3. Castner–Kellner process
  4. Deacon process
Show the answer

Answer: A. Solvay process Ammonia-soda process.

Hydrogenation of oils uses a catalyst of

  1. Pt
  2. Ni
  3. Fe
  4. V₂O₅
Show the answer

Answer: B. Ni Raney/supported nickel.

Saponification produces

  1. esters
  2. soap and glycerol
  3. alcohol and CO₂
  4. acids
Show the answer

Answer: B. soap and glycerol Fat + NaOH.

For storing caustic soda solution of up to about 75 % strength, the least expensive suitable material of construction is

  1. Stainless steel
  2. Plain carbon steel
  3. Nickel
  4. Copper
Show the answer

Answer: B. Plain carbon steel

The best number of effects to use in a multiple-effect evaporator is fixed mainly by

  1. cost benefit analysis.
  2. floor area availability.
  3. terminal parameters.
  4. evaporation capacity required.
Show the answer

Answer: A. cost benefit analysis.

In a modern chemical plant, instruments and controls typically account for about ____ percent of the total plant cost.

  1. 5 to 10
  2. 20 to 30
  3. 40 to 50
  4. 60 to 70
Show the answer

Answer: B. 20 to 30

Installing process equipment usually costs about ____ percent of what the equipment itself cost to buy.

  1. 10 to 20
  2. 35 to 45
  3. 55 to 65
  4. 70 to 80
Show the answer

Answer: B. 35 to 45

The Lang factor relates fixed capital investment to the delivered cost of the main equipment. For a plant handling both solids and fluids, its typical value is

  1. 1.2 to 1.4
  2. 2.5 to 2.7
  3. 4.2 to 4.4
  4. 6.2 to 6.4
Show the answer

Answer: C. 4.2 to 4.4

For an ordinary chemical process plant, utilities make up roughly ____ percent of the total product cost.

  1. 1 to 5
  2. 10 to 20
  3. 25 to 35
  4. 35 to 45
Show the answer

Answer: B. 10 to 20

Among these ceramic tower packings, which one is generally the most expensive?

  1. Berl saddles
  2. Raschig rings
  3. Pall rings
  4. Intalox saddles
Show the answer

Answer: A. Berl saddles

In a fluid-processing plant, piping costs roughly ____ percent of the fixed capital investment.

  1. 4
  2. 13
  3. 22
  4. 34
Show the answer

Answer: B. 13

When estimating total product cost, spending on research and development is placed under

  1. overhead cost
  2. fixed expenses
  3. general expenses
  4. direct production cost
Show the answer

Answer: C. general expenses

Total capital investment of a process plant is the sum of the fixed capital investment and the

  1. overhead cost
  2. working capital
  3. indirect production cost
  4. direct production cost
Show the answer

Answer: B. working capital

Total product cost of a chemical plant equals the manufacturing cost plus the

  1. general expenses
  2. overhead cost
  3. R & D cost
  4. none of these
Show the answer

Answer: A. general expenses

The purchased cost of equipment usually lies between ____ percent of the fixed capital investment.

  1. 10 to 20
  2. 20 to 40
  3. 45 to 60
  4. 65 to 75
Show the answer

Answer: B. 20 to 40

Working capital normally carries a raw-material inventory equal to about ____ month(s) of supply at delivered prices.

  1. one
  2. three
  3. six
  4. twelve
Show the answer

Answer: A. one

By the six-tenths rule, a similar unit with n times the capacity of a known unit costs about ____ times as much.

  1. n^0.6
  2. n^0.5
  3. n^0.7
  4. n
Show the answer

Answer: A. n^0.6

Gross earnings are obtained by subtracting ____ from the total income.

  1. total product cost
  2. fixed cost
  3. income tax
  4. none of these
Show the answer

Answer: A. total product cost

Profit is what remains when ____ is deducted from revenue.

  1. book value
  2. total cost
  3. operating cost
  4. none of these
Show the answer

Answer: B. total cost

With principal p and interest rate i per period, the simple interest earned over n periods is

  1. p.i.n.
  2. p(1 + i.n)
  3. p(1 + i)n
  4. p(1 - i.n)
Show the answer

Answer: A. p.i.n.

Yearly depreciation charges stay the same every year under the ____ method.

  1. declining balance
  2. straight line
  3. sum of the years digit
  4. none of these
Show the answer

Answer: B. straight line

As the discounted-cash-flow rate used rises, the ratio of total present value to the initial investment

  1. decreases
  2. increases
  3. increases linearly
  4. remains constant
Show the answer

Answer: A. decreases

With principal p and compound rate i per period, the interest earned (not the final amount) over n periods is

  1. p|(1+i)ⁿ-1|
  2. p(1+i)ⁿ
  3. p(1-i)ⁿ
  4. p(1+iⁿ)
Show the answer

Answer: A. p|(1+i)ⁿ-1|

For most chemical plants, working capital forms about ____ percent of the total capital investment.

  1. 0.1 to 1
  2. 1 to 2
  3. 10 to 20
  4. 50 to 60
Show the answer

Answer: C. 10 to 20

The nominal and effective interest rates become identical when interest is compounded

  1. annually
  2. fortnightly
  3. monthly
  4. half-yearly
Show the answer

Answer: A. annually

An amount S will be available after n periods at compound rate i. Its present worth is

  1. (1+i)ⁿ/S
  2. S/(1+i)ⁿ
  3. S/(1+in)
  4. S/(1+n)ⁱ
Show the answer

Answer: B. S/(1+i)ⁿ

Which statement about the payback period is correct?

  1. and economic life of a project are the same.
  2. is the length of time over which the earnings on a project equals the investment.
  3. is affected by the variation in earnings after the recovery of the investment.
  4. all (a), (b) and (c).
Show the answer

Answer: B. is the length of time over which the earnings on a project equals the investment.

Which of the following is true of depreciation?

  1. costs (on annual basis) are constant when the straight line method is used for its determination.
  2. is the unavoidable loss in the value of the plant, equipment and materials with lapse in time.
  3. does figure in the calculation of income tax liability on cash flows from an investment.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Rs. 10 000 is invested today at 10 % per year compounded annually. After 5 years it grows to about Rs.

  1. 15000
  2. 16105
  3. 18105
  4. 12500
Show the answer

Answer: B. 16105

The balance sheet of a company shows

  1. the financial condition at any given time.
  2. only current assets.
  3. only fixed assets.
  4. only current and fixed assets.
Show the answer

Answer: A. the financial condition at any given time.

Income tax is usually levied on the

  1. total income
  2. gross earning
  3. total product cost
  4. fixed cost
Show the answer

Answer: B. gross earning

Factory manufacturing cost is the direct production cost together with

  1. fixed charges and plant overhead cost.
  2. and plant overhead cost.
  3. plant overhead cost and administrative expenses.
  4. none of these.
Show the answer

Answer: B. and plant overhead cost.

The break-even point lies where the line of ____ is crossed.

  1. fixed cost and total cost.
  2. total cost and sales revenue.
  3. fixed cost and sales revenue.
  4. none of these.
Show the answer

Answer: B. total cost and sales revenue.

Compared with a debenture holder, a shareholder’s influence over company management is

  1. more
  2. less
  3. same
  4. no
Show the answer

Answer: A. more

Over time, depreciation causes a ____ in profit.

  1. decrease
  2. increase
  3. no change
  4. none of these
Show the answer

Answer: A. decrease

Which of the following belongs to working capital rather than fixed capital?

  1. Utilities plants.
  2. Maintenance and repair inventory.
  3. Process equipments.
  4. Depreciation.
Show the answer

Answer: B. Maintenance and repair inventory.

Under the straight-line method, the book value of an asset falls

  1. linearly
  2. non-linearly
  3. exponentially
  4. logarithmically
Show the answer

Answer: A. linearly

A machine costs Rs. 5000, lasts 5 years and has a salvage value of Rs. 1000. Its yearly straight-line depreciation is Rs.

  1. 300
  2. 600
  3. 800
  4. 1000
Show the answer

Answer: C. 800

Which depreciation method gives book values higher than the straight-line method during the asset’s life?

  1. Multiple straight line method
  2. Sinking fund method
  3. Declining balance method
  4. Sum of the years digit method
Show the answer

Answer: B. Sinking fund method

In the declining-balance method of depreciation,

  1. value of the asset decreases linearly with time.
  2. annual cost of depreciation is same every year.
  3. annual depreciation is the fixed percentage of the property value at the beginning of the particular year.
  4. none of these.
Show the answer

Answer: C. annual depreciation is the fixed percentage of the property value at the beginning of the particular year.

With TR the tax rate, R revenue, e expenses excluding depreciation and D depreciation, the after-tax cash receipt is

  1. (1-TR)(R-E-D)+D
  2. (1-TR)(R-D)+TR.E
  3. None of these
  4. (1-TR)(R-E)+TR.D
Show the answer

Answer: C. None of these

A rate of 10 % per half-year is compounded every half-year. The actual yearly return on the principal is

  1. 10
  2. 20
  3. >20
  4. <20
Show the answer

Answer: C. >20

For the same fluid and flow rate, using a larger pipe diameter makes the pumping cost

  1. decreases.
  2. increases.
  3. remains the same.
  4. may increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian.
Show the answer

Answer: A. decreases.

The economic pipe diameter is chosen on the basis of

  1. viscosity of the fluid.
  2. density of the fluid.
  3. total cost considerations (pumping cost plus fixed cost of the pipe).
  4. none of these.
Show the answer

Answer: C. total cost considerations (pumping cost plus fixed cost of the pipe).

In the early years of an asset’s life, which method charges the largest depreciation?

  1. diminishing balance
  2. straight line
  3. sum of the years digit
  4. sinking fund
Show the answer

Answer: A. diminishing balance

Compared with a small chemical plant, the economic life of a large chemical plant is generally

  1. only slightly more
  2. much more
  3. slightly less
  4. almost equal
Show the answer

Answer: C. slightly less

Which of these accounting relations is NOT valid?

  1. Assets = equities
  2. Assets = liabilities + net worth
  3. Total income = costs + profits
  4. Assets = capital.
Show the answer

Answer: D. Assets = capital.

Which item is NOT shown on a plant’s balance sheet?

  1. current asset
  2. current liability
  3. long term debt
  4. profit
Show the answer

Answer: D. profit

Current assets minus current liabilities, read straight from the balance sheet, gives the

  1. cash ratio
  2. net working capital
  3. current ratio
  4. liquids assets
Show the answer

Answer: B. net working capital

Which of these is NOT a current asset of a chemical company?

  1. Inventories
  2. Marketable securities
  3. Chemical equipments
  4. None of these.
Show the answer

Answer: C. Chemical equipments

Which cost is NOT part of the manufacturing cost?

  1. fixed charges.
  2. plant overheads.
  3. direct products cost.
  4. administrative expenses.
Show the answer

Answer: D. administrative expenses.

Which item is NOT part of working capital?

  1. Raw materials in stock.
  2. Finished products in stock.
  3. Transportation facilities.
  4. Semi-finished products in the process.
Show the answer

Answer: C. Transportation facilities.

The six-tenths factor rule is used to estimate

  1. equipment installation cost.
  2. equipment cost by scaling.
  3. cost of piping.
  4. utilities cost.
Show the answer

Answer: B. equipment cost by scaling.

In an ordinary chemical plant, electrical installation costs roughly

  1. 10-15% of purchased equipment cost.
  2. 3-10% of fixed capital investment.
  3. either (a) or (b).
  4. neither (a) nor (b).
Show the answer

Answer: C. either (a) or (b).

Of these items of fixed capital investment, which usually needs the smallest share?

  1. Electrical installation cost.
  2. Equipment installation cost.
  3. Cost for piping.
  4. Equipment insulation cost.
Show the answer

Answer: A. Electrical installation cost.

Construction expenses amount to about ____ percent of the total direct plant cost.

  1. 2
  2. 10
  3. 30
  4. 50
Show the answer

Answer: B. 10

Gross annual sales divided by fixed capital investment is called the ____ ratio.

  1. cash reserve
  2. capital
  3. turnover
  4. investment
Show the answer

Answer: C. turnover

Which of these cost relations is NOT correct?

  1. Manufacturing cost = direct product cost + fixed charges + plant overhead costs
  2. General expenses = administrative expenses + distribution & marketing expenses
  3. Total product cost = manufacturing cost + general expenses
  4. Total product cost = direct production cost + plant overhead cost.
Show the answer

Answer: D. Total product cost = direct production cost + plant overhead cost.

Which tax is calculated on gross earnings?

  1. Property
  2. Excise
  3. Income
  4. Capital gain
Show the answer

Answer: C. Income

Which of these is NOT counted in depreciation cost?

  1. Repairs and maintenance cost.
  2. Loss due to obsolescence of the equipment.
  3. Loss due to decrease in the demand of product.
  4. Loss due to accident/breakdown in the machinery.
Show the answer

Answer: C. Loss due to decrease in the demand of product.

Yearly depreciation charges change from year to year under the ____ method.

  1. straight line
  2. sinking fund
  3. present worth
  4. declining balance.
Show the answer

Answer: D. declining balance.

Which of these depreciation methods takes interest on the investment into account?

  1. Straight line method
  2. Declining balance
  3. both (a) and (b)
  4. neither (a) nor (b).
Show the answer

Answer: D. neither (a) nor (b).

The chemical engineering plant cost index updates old costs as present cost = original cost × (index now/index then). Its largest component is

  1. fabricated equipment and machinery.
  2. process instruments and control.
  3. pumps and compressors.
  4. electrical equipments and material.
Show the answer

Answer: A. fabricated equipment and machinery.

In plant cost estimation, utilities are included in the

  1. plant overhead cost
  2. fixed charges
  3. direct production cost
  4. general expenses
Show the answer

Answer: C. direct production cost

Nominal and effective interest rates coincide when compounding is done

  1. quarterly
  2. semi-annually
  3. annually
  4. in no case, they are equal
Show the answer

Answer: C. annually

Start-up expenses for bringing a new chemical plant into production can reach about ____ percent of the fixed capital cost.

  1. 1
  2. 5
  3. 10
  4. 30
Show the answer

Answer: C. 10

The cost of treating effluent is classified as a ____ cost.

  1. fixed
  2. overhead
  3. utilities
  4. capital
Show the answer

Answer: C. utilities

Which of these is NOT a selling expense for a chemical product?

  1. Advertising
  2. Warehousing
  3. Legal fees
  4. Customer service.
Show the answer

Answer: C. Legal fees

Which of these materials for pressure vessels is the most expensive?

  1. Low alloy steel
  2. Lead
  3. Titanium
  4. High alloy steel
Show the answer

Answer: C. Titanium

Which statement is wrong?

  1. Gross margin = net income - net expenditure
  2. Net sales realisation (NSR) = Gross sales - selling expenses
  3. At break even point, NSR is more than the total production cost
  4. Net profit = Gross margin - depreciation - interest
Show the answer

Answer: C. At break even point, NSR is more than the total production cost

Which statement is wrong?

  1. Debt-equity ratio of a chemical company describes the lenders contribution for each rupee of owner's contribution i.e., debt-equity ratio = total debt/net worth.
  2. Return on investment (ROI) is the ratio of profit before interest & tax and capital employed (i.e. net worth + total debt).
  3. Working capital = current assets + current liability.
  4. Turn over = opening stock + production - closing stock.
Show the answer

Answer: C. Working capital = current assets + current liability.

The operating profit of a plant equals

  1. profit before interest and tax i.e., net profit + interest + tax
  2. profit after tax plus depreciation
  3. net profit + tax
  4. profit after tax
Show the answer

Answer: A. profit before interest and tax i.e., net profit + interest + tax

Which item is NOT part of fixed capital?

  1. Raw materials inventory.
  2. Utilities plants.
  3. Process equipment.
  4. Emergency facilities.
Show the answer

Answer: A. Raw materials inventory.

Which item is NOT part of working capital?

  1. Product inventory.
  2. In-process inventory.
  3. Minimum cash reserve.
  4. Storage facilities.
Show the answer

Answer: D. Storage facilities.

Which cost is NOT part of the total product cost?

  1. market survey
  2. operating labour, supervision and supplies
  3. overhead and utilities
  4. depreciation, property tax and insurrance
Show the answer

Answer: A. market survey

Which is NOT a fixed charge of a chemical plant?

  1. interest on borrowed money.
  2. rent of land and buildings.
  3. property tax, insurance and depreciation.
  4. repair and maintenance charges.
Show the answer

Answer: D. repair and maintenance charges.

Which of these is a utilities cost?

  1. water supply
  2. running a control laboratory
  3. property protection
  4. medical services
Show the answer

Answer: A. water supply

Rs. 100 is invested at a nominal 10 % per year compounded half-yearly. After one year it becomes about Rs.

  1. 121
  2. 110
  3. 97
  4. 91
Show the answer

Answer: B. 110

The catalysts used in the lead-chamber process and in the contact process for sulphuric acid are, respectively,

  1. V₂O₅ and Cr₂O₃.
  2. oxides of nitrogen and Cr₂O₃.
  3. V₂O₅ on a porous carrier and oxides of nitrogen.
  4. oxides of nitrogen and V₂O₅ on a porous carrier.
Show the answer

Answer: D. oxides of nitrogen and V₂O₅ on a porous carrier.

In the contact process, SO₃ is absorbed in about 97 % sulphuric acid instead of water because

  1. SO₃ gas is sparingly soluble in water.
  2. water forms an acid mist, which is difficult to absorb.
  3. the purity of acid is affected.
  4. scale formation in the absorber is to be avoided.
Show the answer

Answer: B. water forms an acid mist, which is difficult to absorb.

Compared with the chamber process, the contact process for sulphuric acid

  1. yields acid of higher concentration than chamber process.
  2. yields acids of lower concentration than chamber process.
  3. is obsolete.
  4. eliminates absorber.
Show the answer

Answer: A. yields acid of higher concentration than chamber process.

In “20 % oleum”, every 100 kg contains

  1. SO₃ and 80 kg of H₂SO₄.
  2. H₂SO₄ and 80 kg of SO₃.
  3. SO₃ for each 100 kg of H₂SO₄.
  4. none of these.
Show the answer

Answer: A. SO₃ and 80 kg of H₂SO₄.

The Solvay (ammonia–soda) process for soda ash uses as raw materials

  1. salt, limestone and coke or gas.
  2. ammonia, salt and limestone.
  3. ammonia limestone and coke.
  4. none of these.
Show the answer

Answer: B. ammonia, salt and limestone.

The main oxides present in Portland cement are

  1. CaO, SiO₂, Al₂O₃
  2. MgO, SiO₃, K₂O
  3. Al₂O₃, MgO, Fe₂O₃
  4. CaO, MgO, K₂O
Show the answer

Answer: A. CaO, SiO₂, Al₂O₃

Chemically, gypsum is

  1. calcium chloride
  2. potassium sulphate
  3. sodium sulphate
  4. calcium sulphate
Show the answer

Answer: D. calcium sulphate

Glauber’s salt (Na₂SO₄·10H₂O) is chemically which of these?

  1. calcium sulphate
  2. potassium sulphate
  3. potassium chlorate
  4. none of these
Show the answer

Answer: D. none of these

Permanent hardness of water is caused by calcium and magnesium

  1. bi-carbonates
  2. sulphates and chlorides
  3. carbonate
  4. none of these
Show the answer

Answer: B. sulphates and chlorides

A widely used method for treating feed water for boilers is the

  1. cold lime process
  2. coagulation
  3. hot-lime soda process
  4. sequestration
Show the answer

Answer: C. hot-lime soda process

A fatty oil consists mainly of a

  1. mixture of glycerides.
  2. mixture of glycerides of fatty acids.
  3. solid at normal temperature.
  4. ester of alcohols other than glycerine.
Show the answer

Answer: B. mixture of glycerides of fatty acids.

A wax is chemically a

  1. mixture of glycerides.
  2. mixture of esters of polyhydric alcohols excepting glycerine.
  3. liquid at room temperature.
  4. mixture of glycerides of fatty acids.
Show the answer

Answer: B. mixture of esters of polyhydric alcohols excepting glycerine.

Compared with saturated oils, unsaturated oils have

  1. lower melting point and higher reactivity to oxygen.
  2. higher melting point and higher reactivity to oxygen.
  3. lower melting point and lower reactivity to oxygen.
  4. higher melting point and lower reactivity to oxygen.
Show the answer

Answer: A. lower melting point and higher reactivity to oxygen.

The tendency of a fatty oil to turn rancid can be reduced by

  1. decoloration
  2. hydrogenation
  3. oxidation
  4. purification
Show the answer

Answer: B. hydrogenation

The solvent commonly used to extract edible oil from seeds is

  1. hexane
  2. methyl ethyl ketone
  3. furfurol
  4. none of these
Show the answer

Answer: A. hexane

The catalyst used to hydrogenate vegetable oils is

  1. nickel
  2. platinum
  3. iron
  4. alumina
Show the answer

Answer: A. nickel

How do soaps remove dirt?

  1. increasing the surface tension.
  2. decreasing wettability.
  3. supplying hydrophyllic group.
  4. none of these.
Show the answer

Answer: D. none of these.

A “metallic soap” is a fatty-acid salt of

  1. sodium
  2. potassium
  3. both sodium and potassium
  4. aluminium or calcium
Show the answer

Answer: D. aluminium or calcium

Which of these is used as a fat-splitting catalyst?

  1. CaCO₃
  2. ZnO
  3. Al₂O₃
  4. Fe
Show the answer

Answer: B. ZnO

Soap works poorly in hard water because

  1. hard water contains sulphate.
  2. they form insoluble calcium soaps which precipitate.
  3. they attract back the removed dirt.
  4. none of these.
Show the answer

Answer: B. they form insoluble calcium soaps which precipitate.

Builders are added to soaps and detergents mainly as

  1. cleaning power booster
  2. anti-redeposition agent
  3. corrosion inhibitor
  4. fabric brightener
Show the answer

Answer: A. cleaning power booster

Biodegradable detergents are those that

  1. can be readily broken down by oxidation.
  2. pose problems in sewage plants.
  3. have a highly branched isoparaffinic structure.
  4. should not be used as they spoil cloth.
Show the answer

Answer: A. can be readily broken down by oxidation.

Which of these is a synthetic detergent?

  1. Fatty alcohol
  2. Alkyl benzene sulphonate (ABS)
  3. Fatty acids
  4. Methylene chloride
Show the answer

Answer: B. Alkyl benzene sulphonate (ABS)

Essential oils are usually recovered from plant material by

  1. steam distillation
  2. extractive distillation
  3. solvent extraction
  4. leaching
Show the answer

Answer: A. steam distillation

Plasticisers are added to paints to

  1. make it corrosion resistant.
  2. make glossy surface.
  3. give elasticity and prevent cracking of the film.
  4. increase atmospheric oxidation.
Show the answer

Answer: C. give elasticity and prevent cracking of the film.

Which type of oil is preferred for making paints?

  1. Drying oil
  2. Non-drying oil
  3. Semi-drying oil
  4. Saturated oil
Show the answer

Answer: A. Drying oil

The thinner in a paint

  1. accelerate the oxidation of oil.
  2. prevent gelling of the paint.
  3. suspend pigments and dissolve film forming materials.
  4. form a protective film.
Show the answer

Answer: C. suspend pigments and dissolve film forming materials.

Which ingredient is absent in a varnish?

  1. pigment
  2. thinner
  3. dryer
  4. anti-skimming agent
Show the answer

Answer: A. pigment

In sugar manufacture, SO₂ is passed through hot cane juice mainly to

  1. act as an acidifying agent.
  2. increase its concentration.
  3. increase the amount of molasses.
  4. increase the crystal size.
Show the answer

Answer: A. act as an acidifying agent.

Molasses is the raw material for producing

  1. alcohol
  2. essential oil
  3. fatty acids
  4. massecuite
Show the answer

Answer: A. alcohol

Pulp for good paper should be rich in

  1. cellulose
  2. lignin
  3. both (a) and (b)
  4. none of these
Show the answer

Answer: A. cellulose

In the kraft process, white liquor is caustic soda together with

  1. sodium sulphide and sodium carbonate.
  2. sodium sulphite and sodium carbonate.
  3. sodium sulphite and sodium sulphide.
  4. none of these.
Show the answer

Answer: A. sodium sulphide and sodium carbonate.

Which of these is regarded as a high-grade, strong pulp?

  1. Rag pulp
  2. Mechanical pulp
  3. Sulphate pulp
  4. Sulphite pulp
Show the answer

Answer: C. Sulphate pulp

Paper pulp is bleached using

  1. activated clay
  2. bromine
  3. chlorine or chlorine dioxide
  4. magnesium sulphite
Show the answer

Answer: C. chlorine or chlorine dioxide

Sizing agents are added to paper so that it

  1. impart resistance to penetration by liquids.
  2. increase its thickness.
  3. increase its flexibility and opacity.
  4. increase its brightness.
Show the answer

Answer: A. impart resistance to penetration by liquids.

The high-temperature CO shift converter uses a catalyst of

  1. nickel
  2. vanadium
  3. silica gel
  4. iron oxide–chromia
Show the answer

Answer: D. iron oxide–chromia

The main use of phenol is in making

  1. to produce benzene.
  2. to produce phenol formaldehyde.
  3. to produce polyester resin.
  4. as a plasticiser for unsaturated polyster.
Show the answer

Answer: B. to produce phenol formaldehyde.

Phthalic anhydride is produced by

  1. oxidation of naphthalene.
  2. oxidation of benzene.
  3. dehydrogenation of ethyl benzene.
  4. none of these.
Show the answer

Answer: A. oxidation of naphthalene.

TNT (trinitrotoluene) is obtained by nitrating

  1. nitrobenzene
  2. toluene
  3. nitrotoluene
  4. benzene
Show the answer

Answer: B. toluene

Which class of dye is most often used for synthetic fibres such as nylon?

  1. Acid dye
  2. Azoic dye
  3. Pigment dye
  4. Mordant dye
Show the answer

Answer: A. Acid dye

The full form of DDT is

  1. diethyl-diphenyl-trichloromethane.
  2. dichloro-diphenyl-trichloromethane.
  3. diphenyl-dichloro-trichloromethane.
  4. dichloro-diphenyl-trichloroethane.
Show the answer

Answer: D. dichloro-diphenyl-trichloroethane.

BHC (benzene hexachloride) is made by chlorinating benzene

  1. in the presence of FeCl₃ in the dark.
  2. by substitution at room temperature.
  3. in complete darkness.
  4. in the presence of sunlight (UV light).
Show the answer

Answer: D. in the presence of sunlight (UV light).

Typical molecular weights of polymers lie in the range

  1. 10²-10³
  2. 10⁵-10⁹
  3. 10³-10⁷
  4. 10⁹-10¹¹
Show the answer

Answer: C. 10³-10⁷

The Ziegler process

  1. produces high density polyethylene.
  2. produces low density polyethylene.
  3. uses no catalyst.
  4. employs very high pressure.
Show the answer

Answer: A. produces high density polyethylene.

PVC is a ____ material.

  1. thermosetting
  2. thermoplastic
  3. fibrous
  4. chemically active
Show the answer

Answer: B. thermoplastic

PTFE is better known as

  1. bakelite
  2. teflon
  3. celluloid
  4. dacron
Show the answer

Answer: B. teflon

Vulcanisation of rubber

  1. decreases its tensile strength.
  2. increases its reactivity to ozone and oxygen.
  3. decreases its oil and solvent resistance.
  4. converts its plasticity into elasticity.
Show the answer

Answer: D. converts its plasticity into elasticity.

The most widely used agent for vulcanising rubber is

  1. sulphur
  2. bromine
  3. platinum
  4. alumina
Show the answer

Answer: A. sulphur

Celluloid is chemically

  1. cellulose acetate
  2. regenerated cellulose
  3. cellulose nitrate
  4. cellulose acetate butyrate
Show the answer

Answer: C. cellulose nitrate

Thermosetting plastics

  1. are cross-linked molecules.
  2. soften on application of heat.
  3. are solvent soluble.
  4. none of these.
Show the answer

Answer: A. are cross-linked molecules.

Silicon carbide is used as an

  1. adhesive
  2. abrasive
  3. type of glass
  4. brittle material
Show the answer

Answer: B. abrasive

Cumene is manufactured by

  1. oxidation of napthalene.
  2. propylene alkylation of benzene.
  3. polymerisation of a mixture of benzene and propylene.
  4. none of these.
Show the answer

Answer: B. propylene alkylation of benzene.

Cumene is the feedstock for making

  1. benzoic acid
  2. phenol and acetone
  3. isoprene
  4. styrene
Show the answer

Answer: B. phenol and acetone

An exhausted zeolite water softener is regenerated with

  1. brine
  2. chloramines
  3. sodium bisulphite
  4. liquid chlorines
Show the answer

Answer: A. brine

Temporary hardness of water is removed by

  1. addition of alum.
  2. boiling.
  3. filtration through gravity sand filter.
  4. addition of lime.
Show the answer

Answer: B. boiling.

Permanent hardness of water can be removed by

  1. simply boiling.
  2. adding alum.
  3. passing it through cation and anion exchangers.
  4. all (a), (b) and (c).
Show the answer

Answer: C. passing it through cation and anion exchangers.

“Salt cake” has the formula

  1. Na₂SO₄
  2. CaSO₄·½H₂O
  3. MgSO₄
  4. BaSO₄
Show the answer

Answer: A. Na₂SO₄

The Fourdrinier machine is used in making

  1. sugar
  2. paper
  3. alcohol from molasses
  4. phenol formaldehyde
Show the answer

Answer: B. paper

Teflon is

  1. phenol formaldehyde.
  2. an inorganic polymer.
  3. poly tetrafluoroethylene (P.T.F.E.).
  4. a monomer.
Show the answer

Answer: C. poly tetrafluoroethylene (P.T.F.E.).

Parathion and malathion are

  1. pesticides.
  2. plasticisers for unsaturated polysters.
  3. pain relieving drugs.
  4. tranquilisers.
Show the answer

Answer: A. pesticides.

The formula of baking soda is

  1. Na₂CO₃
  2. NaHCO₃
  3. Na₂CO₃.H₂O
  4. Na₂CO₃.10H₂O
Show the answer

Answer: B. NaHCO₃

The formula of washing soda is

  1. Na₂CO₃
  2. Na₂CO₃.H₂O
  3. Na₂CO₃.10H₂O
  4. NaHCO₃
Show the answer

Answer: C. Na₂CO₃.10H₂O

In the Solvay process, the calciner delivers

  1. light soda ash
  2. dense soda ash
  3. sodium bicarbonate
  4. dehydrated soda ash
Show the answer

Answer: A. light soda ash

Which by-product is formed when caustic soda is made by electrolysis of brine?

  1. Na₂CO₃
  2. NaHCO₃
  3. H₂
  4. none of these
Show the answer

Answer: C. H₂

Hydrochloric acid is used mainly for

  1. drilling of petroleum wells and pickling of steel sheets.
  2. manufacture of cationic detergent.
  3. treatment of spent fuel of nuclear reactor.
  4. none of these.
Show the answer

Answer: A. drilling of petroleum wells and pickling of steel sheets.

Blue vitriol is

  1. copper sulphate
  2. ferrous sulphate
  3. copper nitrate
  4. aluminium sulphate
Show the answer

Answer: A. copper sulphate

Natural rubber is mainly

  1. polystyrene
  2. polyisoprene
  3. polybutadiene
  4. polychloroprene
Show the answer

Answer: B. polyisoprene

Alum is commercially made from

  1. gypsum
  2. feldspar
  3. galena
  4. bauxite
Show the answer

Answer: D. bauxite

Which of these is a yellow pigment?

  1. Titanium dioxide
  2. Ferrous sulphate
  3. Lead chromates
  4. Zinc sulphides
Show the answer

Answer: C. Lead chromates

Naphthalene is removed from coke-oven gas by

  1. adsorbing on palladium.
  2. absorbing in ethanolamine.
  3. scrubbing with wash oil.
  4. passing through electrostatic precipitator.
Show the answer

Answer: C. scrubbing with wash oil.

Which impurity in feed water is most harmful for high-pressure boilers?

  1. Silica
  2. Dissolved oxygen
  3. Suspended salt
  4. Dissolved salt
Show the answer

Answer: A. Silica

Converting oils and fats into soap is called

  1. hydrogenation
  2. esterification
  3. saponification
  4. none of these
Show the answer

Answer: C. saponification

The coagulant most widely used to remove suspended matter from water is

  1. bleaching powder
  2. slaked lime
  3. alum
  4. copper sulphate
Show the answer

Answer: C. alum

Phosphate rock is used as raw material for

  1. phosphoric acid
  2. phosphorous
  3. superphosphates
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

In water treatment, a coagulant is added ____ filtration.

  1. before
  2. after
  3. during
  4. to avoid
Show the answer

Answer: A. before

The largest user of sulphuric acid is the ____ industry.

  1. fertiliser
  2. steel
  3. paper
  4. paint
Show the answer

Answer: A. fertiliser

The Frasch process is used for

  1. making oxygen
  2. producing helium
  3. mining sulphur
  4. making nitrogen
Show the answer

Answer: C. mining sulphur

Zeolite softeners are regenerated using

  1. brine
  2. chloramines
  3. sodium bisulphite
  4. liquid chlorines
Show the answer

Answer: A. brine

The Leblanc process was an early method of making

  1. caustic soda
  2. soda ash
  3. bromine from sea water
  4. hydrochloric acid
Show the answer

Answer: B. soda ash

Oleum gives off fumes of

  1. SO₂
  2. H₂SO₄
  3. SO₃
  4. SO₂+H₂SO₄
Show the answer

Answer: C. SO₃

Calcium carbide reacts with water mainly to give

  1. Ca(OH)₃
  2. C₂H₂
  3. CO₂
  4. CaCO₃
Show the answer

Answer: B. C₂H₂

Acetone is produced by catalytic dehydrogenation of

  1. phenol
  2. naphthalene
  3. isopropanol
  4. ethyl benzene
Show the answer

Answer: C. isopropanol

The catalyst used to make ethylene oxide is based on

  1. AgO
  2. Al₂O₃
  3. ZnCl₂
  4. Fe₂O₃
Show the answer

Answer: A. AgO

Ethanolamines are made by reacting ammonia with

  1. ethyl benzene
  2. ethylene oxide
  3. ethanol
  4. ethane
Show the answer

Answer: B. ethylene oxide

Cotton fibre is mainly

  1. lignin
  2. cellulose
  3. starch
  4. gelatine
Show the answer

Answer: B. cellulose

Fermentation is adversely affected by

  1. presence of air.
  2. absence of air.
  3. high concentration.
  4. presence of ammonium salts.
Show the answer

Answer: C. high concentration.

Enzymes are made of

  1. fats
  2. carbohydrates
  3. proteins
  4. amino acids
Show the answer

Answer: C. proteins

Benzene is oxidised to maleic anhydride over

  1. V₂O₅
  2. Pt
  3. Ni
  4. Cr
Show the answer

Answer: A. V₂O₅

An alkali-metal salt of palmitic acid is a

  1. soap
  2. metallic soap
  3. detergent
  4. alkaloid
Show the answer

Answer: A. soap

Na₂CO₃ is known as

  1. washing soda
  2. soda ash
  3. plaster of paris
  4. calcite
Show the answer

Answer: B. soda ash

Pasteurisation of milk means

  1. removal of fatty and albuminous substance from it.
  2. killing of organisms present in it by heating it at controlled temperature without changing its natural characteristics.
  3. inhibiting the growth of micro-organisms without killing them.
  4. none of these.
Show the answer

Answer: B. killing of organisms present in it by heating it at controlled temperature without changing its natural characteristics.

Dry ice (solid CO₂) is mainly used for

  1. storage and shipment of frozen foods and ice-creams.
  2. liquefaction of permanent gases.
  3. liquefaction of natural gas.
  4. none of these.
Show the answer

Answer: A. storage and shipment of frozen foods and ice-creams.

Nitrogen compounds are NOT used in making

  1. fertilisers
  2. gun powder
  3. tip of match sticks
  4. explosive
Show the answer

Answer: C. tip of match sticks

Cobalt-60 is used in therapy and radiography as a source of

  1. X-rays
  2. γ-rays
  3. α-rays
  4. β-rays
Show the answer

Answer: B. γ-rays

Which of these is a non-conventional energy source?

  1. Thermal power
  2. Hydroelectric power
  3. Nuclear-fusion power
  4. Solar power
Show the answer

Answer: D. Solar power

Fahrenheit and Celsius scales read the same at

  1. -55°
  2. -40°
  3. -33°
  4. -58°
Show the answer

Answer: B. -40°

Which of these has the longest wavelength?

  1. radio waves
  2. light
  3. X-ray
  4. Gamma-ray
Show the answer

Answer: A. radio waves

Fog is a colloid of

  1. solid dispersed in gas.
  2. solid dispersed in liquid.
  3. liquid dispersed in gas.
  4. gas dispersed in liquid.
Show the answer

Answer: C. liquid dispersed in gas.

The ability of a substance to exist in two or more crystal forms is called

  1. isomorphism
  2. polymorphism
  3. amorphism
  4. isomerism
Show the answer

Answer: B. polymorphism

Glass is attacked by

  1. H₂SO₃
  2. HF
  3. HNO₃
  4. K₂Cr₂O₇
Show the answer

Answer: B. HF

The first empirical temperature scale to be devised was the

  1. Absolute
  2. Reaumer
  3. Farenhite
  4. Celcius
Show the answer

Answer: C. Farenhite

Lead dissolves most readily in

  1. acetic acid
  2. hydrochloric acid
  3. nitric acid
  4. sulphuric acid.
Show the answer

Answer: C. nitric acid

Which of these is a weak acid?

  1. HF
  2. HCl
  3. HI
  4. HBr
Show the answer

Answer: A. HF

Ship hulls are protected by zinc coatings because zinc is

  1. reduced preferentially.
  2. cheaper.
  3. oxidised preferentially.
  4. lighter.
Show the answer

Answer: C. oxidised preferentially.

At the same conditions, the masses of equal volumes of gases are proportional to their

  1. specific gravities.
  2. densities.
  3. gas characteristic constants.
  4. molecular weights.
Show the answer

Answer: D. molecular weights.

A solution that resists changes in pH when acid or alkali is added is a ____ solution.

  1. neutral
  2. ideal
  3. buffer
  4. zero pH
Show the answer

Answer: C. buffer

Which of these is the largest pressure?

  1. 1 kg/cm²
  2. 1 bar
  3. 1 atmosphere
  4. 1 kilo Pascal
Show the answer

Answer: C. 1 atmosphere

The escape velocity from the earth is about ____ km/s.

  1. 3
  2. 7
  3. 11
  4. 15
Show the answer

Answer: C. 11

Duralumin contains about ____ % copper.

  1. 38
  2. 26
  3. 16
  4. 4
Show the answer

Answer: D. 4

On the Fahrenheit scale, the ice point is

  1. 0°
  2. 32°
  3. 62°
  4. 212°
Show the answer

Answer: B. 32°

Compared with single-stage compression, multistage compression of air gives

  1. power saving per unit weight of air delivered.
  2. moisture elimination in the inter-stage cooler.
  3. increased volumetric efficiency.
  4. all (a), (b) & (c).
Show the answer

Answer: D. all (a), (b) & (c).

Compared with compressing a cold gas, compressing the same gas hot needs

  1. more.
  2. less.
  3. same.
  4. more or less depending upon the nature of the gas.
Show the answer

Answer: A. more.

The closest packing of atoms occurs in the ____ cubic lattice.

  1. face centred
  2. simple cubic
  3. body centred
  4. none of these
Show the answer

Answer: A. face centred

A solar cell turns sunlight directly into ____ energy.

  1. thermal
  2. electrical
  3. mechanical
  4. chemical
Show the answer

Answer: B. electrical

A dike around a storage tank of volume V should hold at least about

  1. V
  2. V/2
  3. 2V
  4. 3V
Show the answer

Answer: A. V

Which gas smells of rotten eggs?

  1. Hydrogen sulphide
  2. Styrene
  3. Phenol
  4. Dimethyl amine
Show the answer

Answer: A. Hydrogen sulphide

Which of these is NOT a frother in froth flotation?

  1. Cresylic acid
  2. Xanthates
  3. Pine oil
  4. all a, b & c
Show the answer

Answer: B. Xanthates

Hooch (illicit liquor) poisoning is usually caused by

  1. ethyl alcohol
  2. impurities
  3. methyl alcohol
  4. carbonic acid
Show the answer

Answer: C. methyl alcohol

The sterilised (buffer) zone around a hazardous chemical plant has a radius of about ____ km.

  1. 0.5
  2. 5
  3. 25
  4. 50
Show the answer

Answer: B. 5

Which of these has the longest wavelength?

  1. radio
  2. light
  3. X-ray
  4. Gamma-ray
Show the answer

Answer: A. radio

Ammonia gas can be dried with

  1. PCl₅
  2. quick lime
  3. CaCl₂
  4. concentrated H₂SO₄
Show the answer

Answer: B. quick lime

Which of these contains no fluorine?

  1. freon
  2. chloroform
  3. teflon
  4. fluorocarbons
Show the answer

Answer: B. chloroform

A sudden large drop in barometric pressure warns of a

  1. rain
  2. cold wave
  3. storm
  4. fair weather
Show the answer

Answer: C. storm

Bulk modulus has the same dimensions as

  1. pressure
  2. density
  3. force
  4. none of these
Show the answer

Answer: A. pressure

When a copper ball is heated, the largest percentage increase is in its

  1. radius
  2. area
  3. mass
  4. volume
Show the answer

Answer: D. volume

Which support is NOT used for vertical vessels?

  1. brackets
  2. skirts
  3. columns
  4. saddles
Show the answer

Answer: D. saddles

Bracket (lug) supports are mainly used for

  1. thick walled vertical
  2. horizontal
  3. thin spherical (e.g. Horton sphere)
  4. none of these
Show the answer

Answer: A. thick walled vertical

Skirt supports are used for

  1. small horizontal
  2. large horizontal
  3. tall vertical
  4. thick walled
Show the answer

Answer: C. tall vertical

Saddle supports are used for

  1. horizontal cylinderical
  2. tall vertical
  3. thick walled vertical
  4. thick spherical
Show the answer

Answer: A. horizontal cylinderical

Wind load on a vessel support may be ignored when the vessel is

  1. tall (say 30 metres), but is full of liquid.
  2. tall but empty.
  3. short (< 2 m) and housed indoor.
  4. none of these.
Show the answer

Answer: C. short (< 2 m) and housed indoor.

Lug supports suit

  1. large horizontal cylindrical
  2. tall but empty
  3. small
  4. thick walled tall
Show the answer

Answer: C. small

The wind force on a tall vessel depends on its

  1. shape.
  2. outside diameter.
  3. height.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

For a seamless pipe, the joint efficiency J is

  1. 1
  2. 0.85
  3. 1.2
  4. <0.5
Show the answer

Answer: A. 1

Cement is a binding material that:

  1. Sets and hardens by reacting with water
  2. Is mixed with sand only
  3. Only dries by evaporation
  4. Does not react with water
Show the answer

Answer: A. Sets and hardens by reacting with water Sets and hardens by reacting with water (hydraulic binder)

Portland cement was invented/patented in:

  1. 1824 by Joseph Aspdin
  2. 1950
  3. 1900
  4. 1750
Show the answer

Answer: A. 1824 by Joseph Aspdin

The raw materials for Portland cement production are primarily:

  1. Gypsum only
  2. Fly ash only
  3. Limestone and clay
  4. Sand and gravel only
Show the answer

Answer: C. Limestone and clay Limestone (CaCO₃) and clay (silica, alumina, iron oxide)

The main kiln process for cement manufacture involves heating raw meal to approximately:

  1. ~200°C
  2. ~600°C
  3. ~800°C
  4. ~1450°C
Show the answer

Answer: D. ~1450°C ~1450°C (clinkerisation temperature)

The four main clinker phases (Bogue compounds) are:

  1. CaO, SiO₂, Al₂O₃, Fe₂O₃
  2. Ca₂, SiO₂, Al₂O₃
  3. C₂S only
  4. C₃S, C₂S, C₃A, C₄AF
Show the answer

Answer: D. C₃S, C₂S, C₃A, C₄AF

C₃S (alite = tricalcium silicate 3CaO·SiO₂) is responsible for:

  1. Early strength development
  2. No strength contribution
  3. Late strength only
  4. Setting time control
Show the answer

Answer: A. Early strength development Early strength development (major contributor)

C₂S (belite = dicalcium silicate 2CaO·SiO₂) is responsible for:

  1. Early strength
  2. Setting time
  3. Long-term strength
  4. No strength contribution
Show the answer

Answer: C. Long-term strength Long-term strength (slow hydration)

C₃A (tricalcium aluminate 3CaO·Al₂O₃) causes:

  1. Slow hydration only
  2. No reaction
  3. Flash setting if uncontrolled, generates most heat of hydration
  4. Late strength
Show the answer

Answer: C. Flash setting if uncontrolled, generates most heat of hydration

Gypsum is added to cement clinker to:

  1. Improve colour
  2. Retard C₃A hydration and control setting time
  3. Reduce cost
  4. Add strength
Show the answer

Answer: B. Retard C₃A hydration and control setting time

C₄AF (tetracalcium aluminoferrite 4CaO·Al₂O₃·Fe₂O₃):

  1. Controls setting
  2. No reaction
  3. Contributes to moderate heat, gives grey colour, modest strength
  4. Main strength component
Show the answer

Answer: C. Contributes to moderate heat, gives grey colour, modest strength

The wet process of cement manufacture:

  1. Prepares raw meal as slurry in long rotary kiln
  2. Uses dry raw meal
  3. Is modern standard
  4. Is more energy-efficient than dry
Show the answer

Answer: A. Prepares raw meal as slurry in long rotary kiln Prepares raw meal as slurry (~35% water) in long rotary kiln - higher energy

The dry process of cement manufacture:

  1. Is older process
  2. Has higher energy consumption
  3. Requires slurry
  4. Prepares dry raw meal
Show the answer

Answer: D. Prepares dry raw meal Prepares dry raw meal - more energy-efficient, modern standard

Precalciner technology in cement plants:

  1. Calcines ~90% of limestone in a separate vessel before kiln, enabling larger kilns
  2. Uses more fuel
  3. Is only for wet process
  4. Is old technology
Show the answer

Answer: A. Calcines ~90% of limestone in a separate vessel before kiln, enabling larger kilns

Calcination of limestone: CaCO₃ →

  1. Ca₃₂
  2. CaO + CO₂
  3. CaSO₄
  4. Ca₂
Show the answer

Answer: B. CaO + CO₂ CaO + CO₂ (occurs at ~850-900°C)

Clinkerization (burning) zone temperature in rotary kiln:

  1. ~1350-1500°C where liquid phase forms and C₃S is produced
  2. ~800°C
  3. ~500°C
  4. ~200°C
Show the answer

Answer: A. ~1350-1500°C where liquid phase forms and C₃S is produced

Clinker cooler after the kiln:

  1. Slowly cools clinker
  2. Rapidly quenches clinker to stabilize phases and recover heat
  3. Adds water to clinker
  4. Only filters dust
Show the answer

Answer: B. Rapidly quenches clinker to stabilize phases and recover heat

Ordinary Portland Cement (OPC) strength classes include:

  1. 100, 200, 300 grade
  2. Only 43 grade
  3. 33, 43, 53 grade
  4. Only M30, M40
Show the answer

Answer: C. 33, 43, 53 grade 33, 43, 53 grade (28-day compressive strength in MPa)

OPC 53 grade means:

  1. None
  2. 53% clinker content
  3. Minimum 53 MPa compressive strength at 28 days
  4. 53 kg per bag
Show the answer

Answer: C. Minimum 53 MPa compressive strength at 28 days

Blended cements include partial replacement of clinker with:

  1. Only gypsum
  2. Only sand
  3. Fly ash, slag, silica fume, pozzolana
  4. Only gravel
Show the answer

Answer: C. Fly ash, slag, silica fume, pozzolana Fly ash, slag, silica fume, pozzolana (supplementary cementitious materials)

Portland Pozzolana Cement (PPC) uses:

  1. No replacement
  2. Only slag
  3. Fly ash or natural pozzolana replacing clinker
  4. Only silica fume
Show the answer

Answer: C. Fly ash or natural pozzolana replacing clinker Fly ash or natural pozzolana (15-35%) replacing clinker

Portland Slag Cement (PSC) uses:

  1. Ground granulated blast furnace slag replacing 25-65% clinker
  2. Silica fume
  3. Fly ash
  4. Natural pozzolana
Show the answer

Answer: A. Ground granulated blast furnace slag replacing 25-65% clinker Ground granulated blast furnace slag (GGBS) replacing 25-65% clinker

White cement differs from OPC in having:

  1. Very low iron content giving white colour
  2. No alumina
  3. Only silica
  4. No calcium
Show the answer

Answer: A. Very low iron content giving white colour Very low iron content (<0.5% Fe₂O₃) giving white colour

Rapid hardening cement (RHC) achieves early strength by:

  1. Adding accelerators
  2. Less water
  3. More gypsum
  4. Higher C₃S content and finer grinding
Show the answer

Answer: D. Higher C₃S content and finer grinding Higher C₃S content and finer grinding - 3-day strength = OPC 28-day

Low heat cement is used in:

  1. Normal construction
  2. Precast concrete
  3. Thin slabs
  4. Mass concrete structures to minimize thermal cracking
Show the answer

Answer: D. Mass concrete structures to minimize thermal cracking Mass concrete structures (dams, thick foundations) to minimize thermal cracking

Sulphate-resisting cement (SRC) has:

  1. High C₃A
  2. Normal composition
  3. Very low C₃A content for resistance to sulphate attack
  4. Extra gypsum
Show the answer

Answer: C. Very low C₃A content for resistance to sulphate attack Very low C₃A content (<5%) for resistance to sulphate attack

Expansion cements (e.g., shrinkage-compensating):

  1. No chemical reaction
  2. Expand slightly during hydration to counteract drying shrinkage
  3. Contract on setting
  4. Normal volume change
Show the answer

Answer: B. Expand slightly during hydration to counteract drying shrinkage

Super-sulphated cement contains mainly:

  1. Granulated slag + calcium sulphate + small clinker
  2. Only clinker
  3. Only slag
  4. Only gypsum
Show the answer

Answer: A. Granulated slag + calcium sulphate + small clinker Granulated slag + calcium sulphate + small clinker - resistant to acids

Fly ash as supplementary cementitious material (SCM) is:

  1. Produced from limestone
  2. By-product of coal combustion in power plants
  3. Quarried material
  4. Sand substitute
Show the answer

Answer: B. By-product of coal combustion in power plants

Silica fume (microsilica) is an ultrafine SCM produced by:

  1. Silicon and ferrosilicon alloy production
  2. Coal combustion
  3. Kiln dust
  4. Blast furnace
Show the answer

Answer: A. Silicon and ferrosilicon alloy production Silicon and ferrosilicon alloy production - very reactive pozzolana

Metakaolin is produced by:

  1. None
  2. Calcination of kaolin clay at 700-800°C
  3. Steel making
  4. Coal burning
Show the answer

Answer: B. Calcination of kaolin clay at 700-800°C Calcination of kaolin clay at 700-800°C - reactive pozzolana

The w/c ratio (water to cement ratio) in concrete:

  1. Has no effect on strength
  2. Only affects workability
  3. Controls strength
  4. Higher w/c → higher strength
Show the answer

Answer: C. Controls strength Controls strength - lower w/c → higher strength (Abrams' law)

Concrete workability is measured by:

  1. Slump test
  2. Air content test
  3. Density measurement
  4. Strength test
Show the answer

Answer: A. Slump test Slump test (slump cone) - higher slump = more workable

Compressive strength of concrete is tested at:

  1. 28 days and 7 days as early indicator
  2. Only 90 days
  3. Only 1 day
  4. Only 7 days
Show the answer

Answer: A. 28 days and 7 days as early indicator 28 days (standard) and 7 days as early indicator

Reinforced concrete combines:

  1. Concrete in compression + steel reinforcement in tension
  2. Only steel
  3. Concrete everywhere
  4. Only concrete
Show the answer

Answer: A. Concrete in compression + steel reinforcement in tension

Prestressed concrete:

  1. Only for beams
  2. Steel wires pre-tensioned or post-tensioned to introduce compressive stress in concrete
  3. No steel
  4. Only for foundations
Show the answer

Answer: B. Steel wires pre-tensioned or post-tensioned to introduce compressive stress in concrete

Admixtures in concrete are used to:

  1. Modify properties
  2. Replace cement
  3. Replace water
  4. Replace aggregate
Show the answer

Answer: A. Modify properties Modify properties (plasticizers, accelerators, retarders, air-entrainers)

Superplasticizers (PCE - polycarboxylate ether) in concrete:

  1. Greatly reduce water demand while maintaining workability
  2. Retard setting
  3. Increase water demand
  4. Only for special concrete
Show the answer

Answer: A. Greatly reduce water demand while maintaining workability Greatly reduce water demand while maintaining workability - high-performance concrete

Air entraining agents in concrete:

  1. Increase strength
  2. Increase density
  3. Reduce setting time
  4. Create tiny air bubbles improving freeze-thaw resistance
Show the answer

Answer: D. Create tiny air bubbles improving freeze-thaw resistance

Alkali-silica reaction (ASR) in concrete is caused by:

  1. Carbonation
  2. Reactive silica in aggregate reacting with alkalis in cement causing expansion cracking
  3. Sulphate attack
  4. Normal hydration
Show the answer

Answer: B. Reactive silica in aggregate reacting with alkalis in cement causing expansion cracking

Carbonation of concrete occurs when:

  1. Temperature changes
  2. CO₂ reacts with Ca₂ reducing pH and depassivating reinforcement
  3. Water enters concrete
  4. Sulphates attack
Show the answer

Answer: B. CO₂ reacts with Ca₂ reducing pH and depassivating reinforcement CO₂ reacts with Ca(OH)₂ reducing pH and depassivating reinforcement

Durability of concrete is related to:

  1. Setting time only
  2. Permeability, w/c ratio, adequate curing, cover depth to steel
  3. Strength only
  4. Aggregate type only
Show the answer

Answer: B. Permeability, w/c ratio, adequate curing, cover depth to steel

Curing of concrete means:

  1. Drying out concrete
  2. Maintaining moisture and temperature for continued hydration and strength gain
  3. Heating concrete to high T
  4. Only adding water once
Show the answer

Answer: B. Maintaining moisture and temperature for continued hydration and strength gain

Steam curing accelerates:

  1. Only heat resistance
  2. Final strength
  3. Early strength development
  4. Setting time reduction
Show the answer

Answer: C. Early strength development Early strength development (used in precast concrete)

Refractory cement (calcium aluminate cement CAC):

  1. Made from bauxite and limestone
  2. Normal Portland cement
  3. For waterproofing
  4. For road construction
Show the answer

Answer: A. Made from bauxite and limestone Made from bauxite and limestone - resistant to high temperatures up to 1500°C

Expansive cement uses:

  1. Lime addition
  2. Aluminium powder
  3. No special reaction
  4. Ettringite formation or calcium sulphoaluminate to expand during hydration
Show the answer

Answer: D. Ettringite formation or calcium sulphoaluminate to expand during hydration

The initial and final setting time of OPC approximately:

  1. Initial: 2 hours; Final: 24 hours
  2. Initial: 30 min min; Final: 10 hours max per IS code
  3. Initial: 1 hour; Final: 5 hours
  4. Initial: 10 min; Final: 30 min
Show the answer

Answer: B. Initial: 30 min min; Final: 10 hours max per IS code

Fineness of cement affects:

  1. Rate of hydration
  2. Only cost
  3. Only colour
  4. Only workability
Show the answer

Answer: A. Rate of hydration Rate of hydration - finer cement hydrates faster giving early strength

Blaine's specific surface area measures:

  1. Cement fineness by air permeability method
  2. Chemical composition
  3. Strength
  4. Setting time
Show the answer

Answer: A. Cement fineness by air permeability method Cement fineness by air permeability method (cm²/g or m²/kg)

Loss on ignition (LOI) in cement testing measures:

  1. Gypsum content
  2. C₃S content
  3. CO₂ and moisture driven off on heating
  4. Fly ash content
Show the answer

Answer: C. CO₂ and moisture driven off on heating CO₂ and moisture driven off on heating - indicates limestone content or pre-hydration

Vicat apparatus is used to determine:

  1. Fineness
  2. Soundness
  3. Strength
  4. Standard consistency, initial and final setting times of cement paste
Show the answer

Answer: D. Standard consistency, initial and final setting times of cement paste

Soundness of cement is tested by:

  1. Strength test
  2. Le Chatelier test or autoclave test
  3. Slump test
  4. Fineness test
Show the answer

Answer: B. Le Chatelier test or autoclave test Le Chatelier test or autoclave test - detects unsound expansion from free CaO or MgO

Free lime (free CaO) in cement clinker is problematic because:

  1. It increases strength
  2. It hydrates slowly with expansion, causing soundness problems
  3. It speeds setting
  4. No problem
Show the answer

Answer: B. It hydrates slowly with expansion, causing soundness problems

Normal consistency (standard water requirement) for OPC is approximately:

  1. 5%
  2. 26-33% by mass of cement
  3. 10-15%
  4. 40-50%
Show the answer

Answer: B. 26-33% by mass of cement

The heat of hydration of cement is problematic in:

  1. All concrete equally
  2. Normal concrete
  3. Mass concrete where temperature rise can cause cracking
  4. Thin slabs
Show the answer

Answer: C. Mass concrete where temperature rise can cause cracking

Heat of hydration of C₃A is approximately:

  1. ~260 kJ/kg
  2. ~502 kJ/kg
  3. ~865 kJ/kg
  4. ~418 kJ/kg
Show the answer

Answer: C. ~865 kJ/kg ~865 kJ/kg (highest of four clinker phases)

Cement kiln dust (CKD) is:

  1. Raw meal
  2. Product of calcination
  3. Fine dust collected from kiln exhaust
  4. Clinker
Show the answer

Answer: C. Fine dust collected from kiln exhaust Fine dust collected from kiln exhaust - can be recycled or used as soil amendment

The cement industry is a major emitter of CO₂ because:

  1. Calcination of limestone releases ~60% process CO₂, rest from fuel combustion
  2. No CO₂ emitted
  3. Only from fuel
  4. Only from electricity
Show the answer

Answer: A. Calcination of limestone releases ~60% process CO₂, rest from fuel combustion

Low-carbon cement alternatives include:

  1. LC3, geopolymers, belite cement
  2. Only OPC with SCM
  3. None
  4. Only blended cement
Show the answer

Answer: A. LC3, geopolymers, belite cement LC3 (limestone calcined clay cement), geopolymers, belite cement

LC3 cement (Limestone Calcined Clay Cement) can reduce:

  1. None
  2. CO₂ emissions by ~30-40% compared to OPC while using less energy
  3. Durability
  4. Strength significantly
Show the answer

Answer: B. CO₂ emissions by ~30-40% compared to OPC while using less energy

Geopolymer cement uses:

  1. Only limestone
  2. Portland clinker always
  3. Aluminosilicate binders activated by alkali solution
  4. Only silica
Show the answer

Answer: C. Aluminosilicate binders activated by alkali solution Aluminosilicate binders activated by alkali solution - no Portland clinker

Carbon capture in cement: oxyfuel or post-combustion capture can reduce:

  1. Only 10%
  2. None
  3. Only 50%
  4. Process CO₂ emissions by 90%+ but adds cost and energy
Show the answer

Answer: D. Process CO₂ emissions by 90%+ but adds cost and energy

Global cement production is approximately:

  1. 10 billion tonnes
  2. 500 million tonnes
  3. ~4 billion tonnes per year
  4. 1 billion tonnes
Show the answer

Answer: C. ~4 billion tonnes per year ~4 billion tonnes per year (2022) - largest manufactured material

China produces approximately what percentage of global cement?

  1. ~35%
  2. ~55%
  3. ~10%
  4. ~20%
Show the answer

Answer: B. ~55%

India is the world's ___ largest cement producer:

  1. 3rd
  2. 1st
  3. 2nd
  4. 4th
Show the answer

Answer: C. 2nd

Concrete is the ___ most used substance on Earth after water:

  1. First
  2. Second
  3. Fourth
  4. Third
Show the answer

Answer: B. Second

M25 concrete mix means:

  1. 25 bags per cubic meter
  2. Mix ratio 1:2.5:5
  3. Only for columns
  4. Characteristic compressive strength of 25 MPa at 28 days
Show the answer

Answer: D. Characteristic compressive strength of 25 MPa at 28 days

The water absorption test for cement determines:

  1. Not standard
  2. Strength
  3. Setting time
  4. Cement quality
Show the answer

Answer: A. Not standard Not standard - water absorption of hardened mortar or concrete is tested

Transporting wet concrete in a transit mixer (truck drum) keeps:

  1. Water separate
  2. Concrete cool
  3. Concrete hot
  4. Concrete workable by slow rotation preventing premature setting
Show the answer

Answer: D. Concrete workable by slow rotation preventing premature setting

Self-compacting concrete (SCC) can:

  1. Not be used for columns
  2. Only be used horizontally
  3. Flow and fill formwork under own weight without vibration
  4. Requires more vibration
Show the answer

Answer: C. Flow and fill formwork under own weight without vibration

Ultra-high performance concrete (UHPC) has compressive strength:

  1. 20-40 MPa
  2. 80-150 MPa
  3. 40-80 MPa
  4. ~150-250 MPa compared to normal 20-40 MPa
Show the answer

Answer: D. ~150-250 MPa compared to normal 20-40 MPa

Pervious concrete allows:

  1. No water passage
  2. Only used for pavements
  3. Water to pass through for stormwater management
  4. Only air passage
Show the answer

Answer: C. Water to pass through for stormwater management

Fibre-reinforced concrete uses fibres of:

  1. Only plastic
  2. Only steel
  3. No improvement
  4. Steel, glass, polypropylene, or carbon to improve tensile and impact resistance
Show the answer

Answer: D. Steel, glass, polypropylene, or carbon to improve tensile and impact resistance

Shot concrete (shotcrete) is:

  1. Precast concrete
  2. None
  3. Cast-in-place only
  4. Pneumatically projected concrete for tunnel linings slopes retaining walls
Show the answer

Answer: D. Pneumatically projected concrete for tunnel linings slopes retaining walls

Roller compacted concrete (RCC) is used for:

  1. Only bridges
  2. Precast only
  3. Normal buildings
  4. Dam construction, pavements
Show the answer

Answer: D. Dam construction, pavements Dam construction, pavements - very dry no-slump concrete compacted by rollers

Mass concrete structures require:

  1. Normal cement always
  2. Low heat cement, cooling pipes, phased pouring to control temperature rise
  3. Maximum hydration
  4. Hot curing
Show the answer

Answer: B. Low heat cement, cooling pipes, phased pouring to control temperature rise

Compressive strength test of concrete cube: standard cube size:

  1. 100 mm × 100 mm
  2. 150 mm × 150 mm × 150 mm per IS code
  3. 50 mm × 50 mm
  4. 200 mm × 200 mm
Show the answer

Answer: B. 150 mm × 150 mm × 150 mm per IS code

Core cutting test on hardened concrete gives:

  1. Only tensile strength
  2. Only flexural strength
  3. In-situ compressive strength assessment of existing structure
  4. Only surface strength
Show the answer

Answer: C. In-situ compressive strength assessment of existing structure

Rebound hammer (Schmidt hammer) test gives:

  1. Tensile strength
  2. Non-destructive surface hardness correlating to compressive strength
  3. Direct strength value
  4. Depth of carbonation
Show the answer

Answer: B. Non-destructive surface hardness correlating to compressive strength

Ultrasonic pulse velocity (UPV) test:

  1. Assesses concrete quality and detects cracks by pulse travel time
  2. Direct strength
  3. Chemical composition
  4. Surface hardness
Show the answer

Answer: A. Assesses concrete quality and detects cracks by pulse travel time

Cover to reinforcement in concrete is provided to:

  1. Protect steel from corrosion and fire
  2. Increase strength
  3. Reduce cracking
  4. Reduce shrinkage
Show the answer

Answer: A. Protect steel from corrosion and fire Protect steel from corrosion and fire - minimum 40-75 mm depending on exposure

Corrosion of reinforcing steel in concrete is initiated by:

  1. Only moisture
  2. Chloride ingress or carbonation reaching steel and destroying passivation
  3. Only load
  4. Only temperature
Show the answer

Answer: B. Chloride ingress or carbonation reaching steel and destroying passivation

Cathodic protection of reinforcement can be applied to:

  1. Only new concrete
  2. Protect steel from corrosion in existing or new chloride-contaminated concrete
  3. Not possible for concrete
  4. Only steel structures
Show the answer

Answer: B. Protect steel from corrosion in existing or new chloride-contaminated concrete

Cement concrete road pavement (rigid pavement) differs from flexible (asphalt) in:

  1. Same life
  2. Lower initial cost
  3. Higher initial cost but longer life and lower maintenance
  4. Same maintenance
Show the answer

Answer: C. Higher initial cost but longer life and lower maintenance

Ready-mix concrete (RMC) is:

  1. Precast concrete
  2. On-site mixed only
  3. Concrete batched and mixed in central plant and delivered by transit mixer
  4. No-fines concrete
Show the answer

Answer: C. Concrete batched and mixed in central plant and delivered by transit mixer

Concrete grade M30 used in:

  1. Only foundations
  2. Structural members
  3. Only pavements
  4. Only mass concrete
Show the answer

Answer: B. Structural members Structural members: columns beams slabs in moderate exposure

Standard cement bag in India weighs:

  1. 100 kg
  2. 25 kg
  3. 50 kg
  4. 40 kg
Show the answer

Answer: C. 50 kg

Specific gravity of cement is approximately:

  1. 3.5
  2. 2.0
  3. 3.15
  4. 2.65
Show the answer

Answer: C. 3.15 3.15 (OPC)

Bulk density of cement (loose) is approximately:

  1. 1000-1300 kg/m³
  2. 3150 kg/m³
  3. 2000 kg/m³
  4. 500 kg/m³
Show the answer

Answer: A. 1000-1300 kg/m³

Sulphuric acid is manufactured by:

  1. Contact process
  2. Lead chamber process
  3. Solvay process
  4. Haber process
Show the answer

Answer: A. Contact process Contact process (SO₂→SO₃ over V₂O₅)

Contact process catalyst:

  1. Fe
  2. V₂O₅
  3. Pt
  4. Ni
Show the answer

Answer: B. V₂O₅ V₂O₅ (vanadium pentoxide)

Haber-Bosch process makes:

  1. Urea
  2. Sulphuric acid
  3. Nitric acid
  4. Ammonia
Show the answer

Answer: D. Ammonia Ammonia (N₂+3H₂→2NH₃)

Haber-Bosch conditions:

  1. ~200°C and 10 atm
  2. ~450°C and 150-300 atm
  3. ~800°C and 1 atm
  4. ~25°C and 1 atm
Show the answer

Answer: B. ~450°C and 150-300 atm

Ostwald process produces:

  1. Nitric acid from NH₃ oxidation
  2. Sulphuric acid
  3. Urea
  4. Ammonia
Show the answer

Answer: A. Nitric acid from NH₃ oxidation

Ostwald process catalyst:

  1. Ni
  2. Pt-Rh gauze
  3. Fe
  4. V₂O₅
Show the answer

Answer: B. Pt-Rh gauze

Solvay process produces:

  1. NaCl
  2. Sodium carbonate
  3. NaOH
  4. Na₂SO₄
Show the answer

Answer: B. Sodium carbonate Sodium carbonate (soda ash)

Chlor-alkali electrolysis produces:

  1. H₂SO₄
  2. Cl₂, H₂, and NaOH
  3. NaCl only
  4. HCl only
Show the answer

Answer: B. Cl₂, H₂, and NaOH

Membrane cell advantage over diaphragm cell:

  1. Cheaper
  2. Less energy
  3. Produces HCl
  4. Purer, more concentrated NaOH
Show the answer

Answer: D. Purer, more concentrated NaOH

Portland cement raw materials:

  1. Sand and gravel only
  2. Limestone and clay
  3. Coal and limestone
  4. None
Show the answer

Answer: B. Limestone and clay Limestone (CaCO₃) and clay

Cement kiln temperature at clinkering zone:

  1. ~1450°C
  2. ~2000°C
  3. ~500°C
  4. ~800°C
Show the answer

Answer: A. ~1450°C

Gypsum is added to cement to:

  1. Add colour
  2. Retard setting
  3. Add strength
  4. Reduce cost
Show the answer

Answer: B. Retard setting

Calcium carbide produced by:

  1. None
  2. Heating CaO+coke in electric arc furnace
  3. Heating limestone
  4. Solvay process
Show the answer

Answer: B. Heating CaO+coke in electric arc furnace Heating CaO+coke in electric arc furnace (~2000°C)

Acetylene from CaC₂:

  1. CaC₂+HCl→C₂H₂
  2. CaC₂+H₂O→C₂H₂+Ca₂
  3. CaC₂+heat→C₂H₂
  4. None
Show the answer

Answer: B. CaC₂+H₂O→C₂H₂+Ca₂ CaC₂+H₂O→C₂H₂+Ca(OH)₂

Vinyl chloride production route:

  1. Oxychlorination of ethylene
  2. Direct chlorination only
  3. Hydration of acetylene
  4. None
Show the answer

Answer: A. Oxychlorination of ethylene Oxychlorination of ethylene (ethylene+HCl+O₂→EDC→VCM)

Steam cracking of naphtha produces:

  1. Methane only
  2. Ethylene, propylene, butadiene, BTX aromatics
  3. Gasoline only
  4. Diesel
Show the answer

Answer: B. Ethylene, propylene, butadiene, BTX aromatics

FCC catalyst:

  1. Fe
  2. V₂O₅
  3. Zeolite Y
  4. Ni/Mo
Show the answer

Answer: C. Zeolite Y Zeolite Y (acid catalyst)

Soap manufacture:

  1. Wax ester
  2. Detergent
  3. Fats+NaOH → soap+glycerol
  4. Paraffin wax
Show the answer

Answer: C. Fats+NaOH → soap+glycerol Fats+NaOH → soap+glycerol (saponification)

Methanol synthesis catalyst:

  1. V₂O₅
  2. Pt
  3. Fe catalyst
  4. Cu/ZnO/Al₂O₃ at 250°C, 50-100 bar
Show the answer

Answer: D. Cu/ZnO/Al₂O₃ at 250°C, 50-100 bar

Fischer-Tropsch converts syngas to:

  1. Ammonia
  2. Liquid hydrocarbons
  3. Methanol only
  4. Ethanol only
Show the answer

Answer: B. Liquid hydrocarbons Liquid hydrocarbons (paraffins, olefins, alcohols)

Ethylene oxide made by:

  1. Chlorination
  2. Partial oxidation of ethylene over Ag catalyst
  3. Cracking of ethane
  4. Hydration of acetylene
Show the answer

Answer: B. Partial oxidation of ethylene over Ag catalyst

Acetic acid industrial production:

  1. Oxidation of ethanol only
  2. Fermentation only
  3. Carbonylation of methanol over Rh or Ir catalyst
  4. None
Show the answer

Answer: C. Carbonylation of methanol over Rh or Ir catalyst

Phenol production (Hock process):

  1. Cumene oxidation → cumene hydroperoxide → phenol+acetone
  2. None
  3. Oxidation of benzene
  4. Chlorobenzene hydrolysis
Show the answer

Answer: A. Cumene oxidation → cumene hydroperoxide → phenol+acetone

Formaldehyde made by:

  1. Reforming
  2. Oxidation of methanol over Ag or Fe-Mo catalyst
  3. None
  4. Pyrolysis of methane
Show the answer

Answer: B. Oxidation of methanol over Ag or Fe-Mo catalyst

Adipic acid produced from:

  1. Benzene direct
  2. Cyclohexane oxidation with HNO₃
  3. None
  4. Naphtha
Show the answer

Answer: B. Cyclohexane oxidation with HNO₃

Styrene produced by:

  1. Reforming
  2. None
  3. Dehydrogenation of ethylbenzene
  4. Hydrogenation of naphthalene
Show the answer

Answer: C. Dehydrogenation of ethylbenzene

Acrylonitrile (SOHIO process):

  1. Propylene+NH₃+O₂ over Bi-Mo catalyst
  2. HCN addition to ethylene
  3. None
  4. Hydration of acetylene
Show the answer

Answer: A. Propylene+NH₃+O₂ over Bi-Mo catalyst Propylene+NH₃+O₂ over Bi-Mo catalyst (ammoxidation)

PTA (purified terephthalic acid) from:

  1. None
  2. Oxidation of toluene
  3. Oxidation of p-xylene
  4. Reforming
Show the answer

Answer: C. Oxidation of p-xylene Oxidation of p-xylene (AMOCO process)

Urea synthesis: raw materials:

  1. NH₃ and CO₂ at high T and P
  2. None
  3. NH₃ and O₂
  4. N₂ and H₂
Show the answer

Answer: A. NH₃ and CO₂ at high T and P

DCDA process:

  1. Increases pressure only
  2. Increases SO₂ conversion >99.7% by double absorption
  3. Single pass only
  4. None
Show the answer

Answer: B. Increases SO₂ conversion >99.7% by double absorption

Oleum is:

  1. H₂SO₄+HNO₃
  2. Dilute H₂SO₄
  3. None
  4. H₂SO₄+dissolved SO₃
Show the answer

Answer: D. H₂SO₄+dissolved SO₃

World's most important industrial chemical by volume:

  1. Ammonia
  2. NaOH
  3. Sulphuric acid
  4. HCl
Show the answer

Answer: C. Sulphuric acid

TSP (triple superphosphate) made by:

  1. Phosphate rock+sulphuric acid
  2. None
  3. Phosphate rock+phosphoric acid
  4. Haber process
Show the answer

Answer: C. Phosphate rock+phosphoric acid

Kraft pulping uses:

  1. NaOH+Na₂S to dissolve lignin
  2. None
  3. HCl
  4. Sulphuric acid
Show the answer

Answer: A. NaOH+Na₂S to dissolve lignin NaOH+Na₂S (white liquor) to dissolve lignin

Biodiesel made by:

  1. Transesterification of triglycerides with methanol+catalyst
  2. Hydrocracking of vegetable oil
  3. Fermentation
  4. None
Show the answer

Answer: A. Transesterification of triglycerides with methanol+catalyst

Steam methane reforming (SMR):

  1. None
  2. Partial oxidation
  3. CH₄+H₂O→CO+3H₂ over Ni catalyst
  4. CH₄ decomposition only
Show the answer

Answer: C. CH₄+H₂O→CO+3H₂ over Ni catalyst

Water-gas shift: CO+H₂O→

  1. None
  2. CO₂+H₂
  3. CH₄+O₂
  4. CO₂+H₂O
Show the answer

Answer: B. CO₂+H₂

Bayer process produces:

  1. None
  2. Alumina from bauxite
  3. Aluminium metal
  4. Iron from ore
Show the answer

Answer: B. Alumina from bauxite Alumina (Al₂O₃) from bauxite

Hall-Héroult process:

  1. Smelting of alumina
  2. None
  3. Acid leaching
  4. Electrolysis of Al₂O₃ in molten cryolite
Show the answer

Answer: D. Electrolysis of Al₂O₃ in molten cryolite

Kroll process produces:

  1. Steel
  2. Titanium metal
  3. Aluminium
  4. None
Show the answer

Answer: B. Titanium metal Titanium metal (TiCl₄+Mg→Ti+MgCl₂)

Float glass process:

  1. On water
  2. On lead
  3. On mercury
  4. Molten glass floated on molten tin bath
Show the answer

Answer: D. Molten glass floated on molten tin bath

Zeolites used as:

  1. Selective shape-specific catalysts and adsorbents
  2. Fuels
  3. Lubricants
  4. Pigments
Show the answer

Answer: A. Selective shape-specific catalysts and adsorbents

Main route for global H₂ production:

  1. Fermentation
  2. Coal gasification only
  3. Water electrolysis
  4. Steam methane reforming
Show the answer

Answer: D. Steam methane reforming Steam methane reforming (~95%)

Carbon black main use:

  1. Pigment for paint
  2. None
  3. Fuel
  4. Reinforcement in tyres
Show the answer

Answer: D. Reinforcement in tyres

Activated carbon made by:

  1. Simple burning
  2. None
  3. Chemical synthesis
  4. Carbonisation + activation with steam or CO₂
Show the answer

Answer: D. Carbonisation + activation with steam or CO₂

Caprolactam made from:

  1. Adipic acid
  2. Toluene direct
  3. Cyclohexanone via Beckmann rearrangement
  4. None
Show the answer

Answer: C. Cyclohexanone via Beckmann rearrangement

Rayon (viscose) made by:

  1. Fermentation
  2. None
  3. Dissolving cellulose as xanthate in NaOH, extruding, regenerating
  4. Direct spinning
Show the answer

Answer: C. Dissolving cellulose as xanthate in NaOH, extruding, regenerating

High-fructose corn syrup (HFCS) from:

  1. None
  2. Acid hydrolysis only
  3. Fermentation only
  4. Corn starch hydrolysis + glucose isomerisation by enzyme
Show the answer

Answer: D. Corn starch hydrolysis + glucose isomerisation by enzyme

Citric acid produced by:

  1. Fermentation of sucrose/glucose with Aspergillus niger
  2. None
  3. Chemical synthesis
  4. Coal processing
Show the answer

Answer: A. Fermentation of sucrose/glucose with Aspergillus niger

MDI made from:

  1. Aniline+formaldehyde→MDA→phosgene→MDI
  2. None
  3. Toluene+NOx
  4. Benzene+HCN
Show the answer

Answer: A. Aniline+formaldehyde→MDA→phosgene→MDI

Nitration of benzene mechanism:

  1. Electrophilic aromatic substitution; nitronium ion attacks ring
  2. Free radical
  3. None
  4. Nucleophilic
Show the answer

Answer: A. Electrophilic aromatic substitution; nitronium ion attacks ring Electrophilic aromatic substitution; nitronium ion (NO₂⁺) attacks ring

Sulphonation of benzene product:

  1. Chlorobenzene
  2. None
  3. Nitrobenzene
  4. Benzene sulphonic acid
Show the answer

Answer: D. Benzene sulphonic acid Benzene sulphonic acid (reversible reaction)

Friedel-Crafts alkylation:

  1. Alkyl group added to benzene ring using alkyl halide + AlCl₃ catalyst
  2. None
  3. Nucleophilic
  4. Free radical
Show the answer

Answer: A. Alkyl group added to benzene ring using alkyl halide + AlCl₃ catalyst

Cracking in petroleum refining:

  1. None
  2. Breaking large hydrocarbon molecules into smaller more valuable products
  3. Isomerisation
  4. Reforming
Show the answer

Answer: B. Breaking large hydrocarbon molecules into smaller more valuable products

Dehydrogenation removes:

  1. Nitrogen
  2. Hydrogen from molecule to form double bond or aromatic ring
  3. Oxygen
  4. Sulphur
Show the answer

Answer: B. Hydrogen from molecule to form double bond or aromatic ring

Hydrogenation adds:

  1. None
  2. Oxygen
  3. Carbon
  4. Hydrogen across double bonds using Ni, Pd, Pt catalyst
Show the answer

Answer: D. Hydrogen across double bonds using Ni, Pd, Pt catalyst Hydrogen across double bonds (saturation) using Ni, Pd, Pt catalyst

Reforming (chemical) of natural gas:

  1. Converts CH₄ + H₂O → syngas over Ni catalyst
  2. Cracking
  3. Polymerisation
  4. None
Show the answer

Answer: A. Converts CH₄ + H₂O → syngas over Ni catalyst Converts CH₄ + H₂O → syngas (CO + H₂) over Ni catalyst

Autothermal reforming (ATR) combines:

  1. Only steam reforming
  2. Steam reforming and partial oxidation in one reactor
  3. Only POX
  4. None
Show the answer

Answer: B. Steam reforming and partial oxidation in one reactor Steam reforming and partial oxidation in one reactor - no external heat

Sabatier reaction:

  1. None
  2. CO₂ + H₂O → CO + H₂
  3. CO₂ + 4H₂ → CH₄ + 2H₂O over Ni catalyst
  4. CO + H₂ → CH₄
Show the answer

Answer: C. CO₂ + 4H₂ → CH₄ + 2H₂O over Ni catalyst CO₂ + 4H₂ → CH₄ + 2H₂O (methanation) over Ni catalyst

Reverse water-gas shift:

  1. None
  2. Water-gas shift
  3. Sabatier
  4. CO₂ + H₂ → CO + H₂O
Show the answer

Answer: D. CO₂ + H₂ → CO + H₂O CO₂ + H₂ → CO + H₂O (endothermic, high T) - CO₂ utilisation

Green hydrogen:

  1. H₂ produced by electrolysis using renewable electricity
  2. Blue H₂
  3. None
  4. Grey H₂
Show the answer

Answer: A. H₂ produced by electrolysis using renewable electricity H₂ produced by electrolysis using renewable electricity - zero carbon

Blue hydrogen:

  1. H₂ from SMR with carbon capture and storage
  2. Green H₂
  3. None
  4. Grey H₂
Show the answer

Answer: A. H₂ from SMR with carbon capture and storage H₂ from SMR with carbon capture and storage (CCS)

Syngas composition ratio H₂:CO =

  1. 5:1
  2. ~3:1 from steam reforming; ~2:1 from partial oxidation
  3. 1:1
  4. None
Show the answer

Answer: B. ~3:1 from steam reforming; ~2:1 from partial oxidation

Methanol-to-Propylene (MTP) process:

  1. None
  2. Reforming
  3. MTO process
  4. Methanol converted to propylene selectively over ZSM-5 catalyst
Show the answer

Answer: D. Methanol converted to propylene selectively over ZSM-5 catalyst Methanol converted to propylene selectively over ZSM-5 catalyst (Lurgi/Linde)

Direct coal liquefaction:

  1. Gasification only
  2. None
  3. Coal hydrogenated at high T and P to produce liquid fuels
  4. Indirect
Show the answer

Answer: C. Coal hydrogenated at high T and P to produce liquid fuels Coal hydrogenated at high T and P to produce liquid fuels (Bergius process)

Indirect coal liquefaction:

  1. Bergius process
  2. Direct hydrogenation
  3. Coal → gasification → syngas → F-T synthesis → liquid fuels
  4. None
Show the answer

Answer: C. Coal → gasification → syngas → F-T synthesis → liquid fuels

Poly(vinyl alcohol) (PVA) made by:

  1. Fermentation
  2. Polymerisation of vinyl alcohol
  3. Hydrolysis of polyvinyl acetate
  4. None
Show the answer

Answer: C. Hydrolysis of polyvinyl acetate Hydrolysis of polyvinyl acetate (PVAc) - no direct vinyl alcohol monomer

PTFE (Teflon) polymerised from:

  1. Fluorine only
  2. None
  3. Tetrafluoroethylene
  4. TFE
Show the answer

Answer: C. Tetrafluoroethylene Tetrafluoroethylene (CF₂=CF₂) - extremely chemically resistant

Latex (natural rubber) coagulated by:

  1. Heating
  2. Cooling
  3. None
  4. Acetic or formic acid addition
Show the answer

Answer: D. Acetic or formic acid addition Acetic or formic acid addition (lowers pH, destabilises colloid)

Vulcanisation of rubber:

  1. Adding filler
  2. Polymerisation
  3. None
  4. Cross-linking rubber chains with sulphur at elevated temperature
Show the answer

Answer: D. Cross-linking rubber chains with sulphur at elevated temperature Cross-linking rubber chains with sulphur at elevated temperature - improves strength

Reforming of naphtha - octane improvement:

  1. None
  2. Branched paraffins and aromatics have higher octane than straight-chain
  3. Reduces octane
  4. No change
Show the answer

Answer: B. Branched paraffins and aromatics have higher octane than straight-chain Branched paraffins and aromatics have higher octane than straight-chain - reformer increases RON

RON vs MON octane:

  1. None
  2. RON > MON; difference = fuel sensitivity; engine knock relates to MON
  3. MON always higher
  4. Same measure
Show the answer

Answer: B. RON > MON; difference = fuel sensitivity; engine knock relates to MON RON (Research Octane Number) > MON; difference = fuel sensitivity; engine knock relates to MON

Lead replacement in petrol:

  1. Only ethanol
  2. Oxygenates, alkylate, reformate, isomerate
  3. None
  4. No replacement possible
Show the answer

Answer: B. Oxygenates, alkylate, reformate, isomerate Oxygenates (MTBE, ethanol), alkylate, reformate, isomerate - replace leaded anti-knock compounds

Catalytic cracking vs thermal cracking products:

  1. Thermal more branched
  2. Catalytic
  3. Same products
  4. None
Show the answer

Answer: B. Catalytic Catalytic: more branched paraffins, olefins; thermal: more straight chain, more gas

Naphtha hydrotreating before reforming:

  1. Not needed
  2. After reforming
  3. None
  4. Removes S, N, O, metals that poison Pt reforming catalyst
Show the answer

Answer: D. Removes S, N, O, metals that poison Pt reforming catalyst

Platformer recycle gas purpose:

  1. Feed dilution
  2. Hydrogen-rich; suppresses coke formation on Pt catalyst
  3. None
  4. Pressure control
Show the answer

Answer: B. Hydrogen-rich; suppresses coke formation on Pt catalyst

Coke yield in FCC:

  1. 20%
  2. ~5-8 wt%
  3. None
  4. 0%
Show the answer

Answer: B. ~5-8 wt% ~5-8 wt% - burns in regenerator to heat catalyst for reaction

LPG from FCC:

  1. Propylene and butylenes
  2. None
  3. Only propane
  4. No LPG
Show the answer

Answer: A. Propylene and butylenes Propylene and butylenes - valuable petrochemical feedstocks

Visbreaker mild cracking temperature:

  1. 300°C
  2. ~450-500°C
  3. None
  4. 800°C
Show the answer

Answer: B. ~450-500°C ~450-500°C - just enough to break long chains, reduce viscosity

Delayed coker temperature:

  1. None
  2. ~490-510°C in fractionator bottoms before coke drums
  3. 300°C
  4. 700°C
Show the answer

Answer: B. ~490-510°C in fractionator bottoms before coke drums

Petroleum coke (pet coke) uses:

  1. Fuel in cement kilns, power plants; anode-grade coke for aluminium smelting
  2. None
  3. Only fuel
  4. No commercial use
Show the answer

Answer: A. Fuel in cement kilns, power plants; anode-grade coke for aluminium smelting

Hydrocracker products:

  1. Only diesel
  2. Diesel, jet fuel, naphtha
  3. Only naphtha
  4. None
Show the answer

Answer: B. Diesel, jet fuel, naphtha Diesel, jet fuel, naphtha - very low sulphur; better quality than FCC

Dewaxing of lube oil:

  1. None
  2. Removes S
  3. Removes wax to lower pour point
  4. Removes N
Show the answer

Answer: C. Removes wax to lower pour point Removes wax (long n-paraffins) to lower pour point - solvent dewaxing or catalytic hydroisodewaxing

Solvent extraction of aromatics:

  1. Hydrogenation
  2. None
  3. Sulfolane, NMP, or DEG extract BTX from reformate
  4. Cracking
Show the answer

Answer: C. Sulfolane, NMP, or DEG extract BTX from reformate Sulfolane, NMP, or DEG extract BTX from reformate - used in aromatics complex

Sulfolane process:

  1. Physical separation
  2. None
  3. Extractive distillation/liquid-liquid extraction for BTX separation using sulfolane as solvent
  4. Distillation only
Show the answer

Answer: C. Extractive distillation/liquid-liquid extraction for BTX separation using sulfolane as solvent

Parex process for PX:

  1. Distillation
  2. Simulated moving bed adsorption separates PX from mixed xylenes
  3. Crystallisation only
  4. None
Show the answer

Answer: B. Simulated moving bed adsorption separates PX from mixed xylenes Simulated moving bed adsorption (Zeolite) separates PX from mixed xylenes

Isomar process:

  1. Separate xylenes
  2. Crack xylenes
  3. None
  4. Isomerises low-PX raffinate back to equilibrium PX content
Show the answer

Answer: D. Isomerises low-PX raffinate back to equilibrium PX content Isomerises low-PX raffinate back to equilibrium PX content - recycles non-PX xylenes

HDPE production - Philips process:

  1. None
  2. CrO₃/SiO₂ catalyst at ~100°C, 30-40 bar
  3. Ziegler-Natta
  4. Radical
Show the answer

Answer: B. CrO₃/SiO₂ catalyst at ~100°C, 30-40 bar CrO₃/SiO₂ catalyst at ~100°C, 30-40 bar - gives broad MWD HDPE

PP global consumption:

  1. None
  2. Only 10 Mt
  3. 200 Mt
  4. ~80 million tonnes/year
Show the answer

Answer: D. ~80 million tonnes/year ~80 million tonnes/year - fastest growing major thermoplastic

ABS production:

  1. None
  2. Only condensation
  3. Only addition
  4. Emulsion or mass polymerisation
Show the answer

Answer: D. Emulsion or mass polymerisation Emulsion or mass polymerisation - rubber (PBR) grafted with SAN

Polystyrene (GPPS vs HIPS):

  1. GPPS
  2. None
  3. HIPS transparent
  4. Same material
Show the answer

Answer: A. GPPS GPPS: brittle, transparent; HIPS: rubber-toughened (PBR), opaque, tougher

Polycarbonate production capacity:

  1. ~5-6 million tonnes/year globally
  2. 20 Mt
  3. Only 1 Mt
  4. None
Show the answer

Answer: A. ~5-6 million tonnes/year globally ~5-6 million tonnes/year globally - growing for automotive, electronics

PET recycling:

  1. None
  2. Mechanical and chemical recycling methods
  3. Only downcycling
  4. Not recyclable
Show the answer

Answer: B. Mechanical and chemical recycling methods Mechanical (rPET bottle-to-bottle) and chemical (glycolysis, methanolysis) recycling methods

Bioplastics examples:

  1. All petroleum-based
  2. Only PLA
  3. None
  4. PLA, PHA, bio-PE, bio-PET
Show the answer

Answer: D. PLA, PHA, bio-PE, bio-PET PLA (from starch), PHA, bio-PE (from sugarcane ethanol), bio-PET (partially bio-based)

Lignin valorisation:

  1. Lignosulphonates, vanillin, BTX via pyrolysis
  2. Only burned
  3. None
  4. No value
Show the answer

Answer: A. Lignosulphonates, vanillin, BTX via pyrolysis Lignosulphonates (dispersant), vanillin, BTX via pyrolysis - moving toward bio-refinery

Biorefinery concept:

  1. Only chemicals
  2. Processing biomass to multiple products
  3. None
  4. Only energy
Show the answer

Answer: B. Processing biomass to multiple products Processing biomass to multiple products (chemicals, fuels, energy) - similar to petroleum refinery

Fischer-Tropsch wax (FT wax):

  1. Aromatic product
  2. Long-chain paraffins from FT synthesis
  3. Light gas only
  4. None
Show the answer

Answer: B. Long-chain paraffins from FT synthesis Long-chain paraffins from FT synthesis - high melting point; hydrocracked to diesel or used directly

Syngas from gasification applications:

  1. Ammonia, methanol, FT, power, H₂ production
  2. Only ammonia
  3. Only methanol
  4. None
Show the answer

Answer: A. Ammonia, methanol, FT, power, H₂ production Ammonia (via Haber), methanol, FT, power (IGCC), H₂ production

Coal-to-Chemicals (CTC) dominant in:

  1. India
  2. USA
  3. Europe
  4. China
Show the answer

Answer: D. China China - largest coal-to-chemicals industry globally (methanol, olefins from coal)

GTL (Gas-to-Liquids) major plants:

  1. Only coal
  2. Only biomass
  3. None
  4. Shell Pearl GTL
Show the answer

Answer: D. Shell Pearl GTL Shell Pearl GTL (Qatar) - converts natural gas to liquid fuels and chemicals via FT

Methanol-to-Olefins (MTO) commercial plants:

  1. None
  2. China has >30 commercial MTO plants
  3. Only USA
  4. Only pilot plants
Show the answer

Answer: B. China has >30 commercial MTO plants China has >30 commercial MTO plants (Dalian/DICP process; DMTO)

Zeolite ZSM-5 in petrochemicals:

  1. [
  2. M
  3. "
  4. F
Show the answer

Answer: A. [

SAPO-34 in MTO:

  1. i
  2. [
  3. S
  4. "
Show the answer

Answer: B. [

Fluid coking vs delayed coking:

  1. [
  2. F
  3. l
  4. "
Show the answer

Answer: A. [

Biomass fast pyrolysis:

  1. a
  2. [
  3. "
  4. R
Show the answer

Answer: B. [

HTL (Hydrothermal Liquefaction):

  1. o
  2. C
  3. "
  4. [
Show the answer

Answer: D. [

Reforming severity:

  1. H
  2. i
  3. [
  4. "
Show the answer

Answer: C. [

Chloride promoter in reforming:

  1. [
  2. r
  3. O
  4. "
Show the answer

Answer: A. [

Coking mechanism in steam cracking:

  1. "
  2. a
  3. R
  4. [
Show the answer

Answer: D. [

Quench oil in steam cracker:

  1. e
  2. [
  3. H
  4. "
Show the answer

Answer: B. [

Demethaniser temperature:

  1. [
  2. 8
  3. "
  4. −
Show the answer

Answer: A. [

PP impact copolymer production:

  1. T
  2. w
  3. "
  4. [
Show the answer

Answer: D. [

Nylon 11 from castor oil:

  1. n
  2. [
  3. "
  4. U
Show the answer

Answer: B. [

Polylactic acid (PLA) compostability:

  1. n
  2. I
  3. [
  4. "
Show the answer

Answer: C. [

Castor oil polyurethane:

  1. C
  2. [
  3. a
  4. "
Show the answer

Answer: B. [

Polypropylene fibre for nonwovens:

  1. S
  2. [
  3. "
  4. p
Show the answer

Answer: B. [

Catalytic dehydrogenation of ethylbenzene selectivity:

  1. None
  2. 50% selectivity
  3. ~95% selectivity to styrene
  4. 100% selectivity
Show the answer

Answer: C. ~95% selectivity to styrene ~95% selectivity to styrene - side reactions: cracking to benzene+ethylene, toluene+methane

Caprolactam purity requirement for nylon:

  1. None
  2. ≥99.9% for polymer-grade
  3. 95% sufficient
  4. No specification
Show the answer

Answer: B. ≥99.9% for polymer-grade ≥99.9% for polymer-grade - even trace impurities affect molecular weight and colour

Food preservation aims to:

  1. Improve flavour only
  2. Add colour
  3. Prevent or slow spoilage by controlling microbes, enzymes, and chemical changes
  4. Increase weight
Show the answer

Answer: C. Prevent or slow spoilage by controlling microbes, enzymes, and chemical changes

Pasteurisation kills:

  1. Only viruses
  2. Only bacteria
  3. All microorganisms including spores
  4. Pathogenic microorganisms; extends shelf life
Show the answer

Answer: D. Pathogenic microorganisms; extends shelf life Pathogenic microorganisms (not all spores); extends shelf life

HTST pasteurisation for milk:

  1. 121°C for 15 min
  2. 63°C for 30 min
  3. 72°C for 15 seconds
  4. 100°C for 10 s
Show the answer

Answer: C. 72°C for 15 seconds

LTLT (Vat) pasteurisation:

  1. 72°C for 15 s
  2. None
  3. 63°C for 30 minutes
  4. 100°C for 5 min
Show the answer

Answer: C. 63°C for 30 minutes

UHT (Ultra-High Temperature) treatment:

  1. 100°C for 30 min
  2. 72°C for 15 s
  3. None
  4. 135-150°C for 2-5 seconds; commercially sterile; 6-month ambient shelf life
Show the answer

Answer: D. 135-150°C for 2-5 seconds; commercially sterile; 6-month ambient shelf life

Sterilisation of canned food (retorting):

  1. 121°C for sufficient time to achieve 12D reduction of Clostridium botulinum spores
  2. None
  3. 100°C for 10 min
  4. 72°C for 15 s
Show the answer

Answer: A. 121°C for sufficient time to achieve 12D reduction of Clostridium botulinum spores 121°C (250°F) for sufficient time to achieve 12D reduction of Clostridium botulinum spores

F₀ value in canning:

  1. None
  2. Temperature applied
  3. Equivalent sterilisation time at 121.1°C
  4. Actual process time
Show the answer

Answer: C. Equivalent sterilisation time at 121.1°C Equivalent sterilisation time at 121.1°C (250°F) - measure of thermal process lethality

D-value is:

  1. None
  2. Temperature for kill
  3. Time at constant temperature to reduce microbial population by 90%
  4. Time for complete kill
Show the answer

Answer: C. Time at constant temperature to reduce microbial population by 90% Time at constant temperature to reduce microbial population by 90% (1 log cycle)

Z-value is:

  1. None
  2. Temperature change needed to change D-value by 10-fold
  3. Kill rate
  4. D-value change
Show the answer

Answer: B. Temperature change needed to change D-value by 10-fold

Freezing preserves food by:

  1. Slowing microbial growth and enzymatic reactions; water converted to ice
  2. None
  3. Killing all microbes
  4. Adding preservatives
Show the answer

Answer: A. Slowing microbial growth and enzymatic reactions; water converted to ice

IQF stands for:

  1. None
  2. Industry Quick Freeze
  3. Instant Quality Frozen
  4. Individually Quick Frozen
Show the answer

Answer: D. Individually Quick Frozen Individually Quick Frozen - freezing individual pieces rapidly

Freeze-drying (lyophilisation):

  1. Spray drying
  2. None
  3. Frozen product sublimed under vacuum; highest quality retention
  4. Heat drying
Show the answer

Answer: C. Frozen product sublimed under vacuum; highest quality retention

Spray drying produces:

  1. Foam
  2. Fine powder from liquid/slurry
  3. Pellets
  4. Sheets
Show the answer

Answer: B. Fine powder from liquid/slurry Fine powder from liquid/slurry (e.g. milk powder, instant coffee)

Water activity (aw) of a food:

  1. pH
  2. None
  3. Total water content
  4. Ratio of vapour pressure of food to pure water; controls microbial growth
Show the answer

Answer: D. Ratio of vapour pressure of food to pure water; controls microbial growth

aw < 0.6 inhibits:

  1. Only bacteria
  2. Only yeasts
  3. None
  4. All microbial growth
Show the answer

Answer: D. All microbial growth All microbial growth (most microbes need aw > 0.85)

Maillard reaction is:

  1. Oxidation
  2. Caramelisation
  3. Non-enzymatic browning between reducing sugars and amino acids
  4. Enzymatic browning
Show the answer

Answer: C. Non-enzymatic browning between reducing sugars and amino acids Non-enzymatic browning between reducing sugars and amino acids (baking, roasting)

Caramelisation is:

  1. None
  2. Maillard reaction
  3. Enzymatic reaction
  4. Thermal degradation of sugars producing brown compounds and flavour
Show the answer

Answer: D. Thermal degradation of sugars producing brown compounds and flavour Thermal degradation of sugars producing brown compounds and flavour (no amino acids needed)

Enzymatic browning (e.g. cut apple) caused by:

  1. Caramelisation
  2. Maillard reaction
  3. Polyphenol oxidase oxidising phenolic compounds
  4. None
Show the answer

Answer: C. Polyphenol oxidase oxidising phenolic compounds Polyphenol oxidase (PPO) oxidising phenolic compounds

PPO activity prevented by:

  1. Cooling only
  2. Freezing only
  3. Blanching, acidification, or exclusion of O₂
  4. Adding sugar
Show the answer

Answer: C. Blanching, acidification, or exclusion of O₂ Blanching, acidification (lemon juice/ascorbic acid), or exclusion of O₂

Blanching is:

  1. Frying
  2. None
  3. Full cooking
  4. Brief heat treatment to inactivate enzymes before freezing or canning
Show the answer

Answer: D. Brief heat treatment to inactivate enzymes before freezing or canning

pH control as preservation (acids):

  1. pH has no effect
  2. None
  3. Low pH inhibits most pathogens including C. botulinum
  4. High pH preserves
Show the answer

Answer: C. Low pH inhibits most pathogens including C. botulinum Low pH (< 4.6) inhibits most pathogens including C. botulinum

aw and pH combined barriers (hurdle technology):

  1. High heat always
  2. None
  3. Multiple mild preservation factors combined for effective preservation with less heat
  4. Single factor only
Show the answer

Answer: C. Multiple mild preservation factors combined for effective preservation with less heat

Modified Atmosphere Packaging (MAP):

  1. Replacing air in package with N₂, CO₂, or O₂ mix to extend shelf life
  2. Adding preservatives
  3. Vacuum only
  4. None
Show the answer

Answer: A. Replacing air in package with N₂, CO₂, or O₂ mix to extend shelf life

Active packaging:

  1. Packaging that interacts with food or atmosphere
  2. Normal packaging
  3. Passive packaging
  4. None
Show the answer

Answer: A. Packaging that interacts with food or atmosphere Packaging that interacts with food or atmosphere (O₂ scavengers, moisture control)

HACCP stands for:

  1. High Accuracy Chemical Control Process
  2. Hazard Analysis Critical Control Points
  3. None
  4. Hazardous Agent Critical Chemist Panel
Show the answer

Answer: B. Hazard Analysis Critical Control Points Hazard Analysis Critical Control Points - food safety management system

Critical Control Point (CCP) is:

  1. None
  2. Step where control can be applied to prevent or eliminate food hazard
  3. Only cooking step
  4. Any step in process
Show the answer

Answer: B. Step where control can be applied to prevent or eliminate food hazard

Clostridium botulinum produces:

  1. Botulinum toxin
  2. Aflatoxin
  3. Ergotism
  4. None
Show the answer

Answer: A. Botulinum toxin Botulinum toxin - most lethal biological toxin; risk in low-acid canned foods

Aflatoxins are produced by:

  1. Clostridium
  2. Salmonella
  3. None
  4. Aspergillus flavus and A. parasiticus on groundnuts, maize, nuts
Show the answer

Answer: D. Aspergillus flavus and A. parasiticus on groundnuts, maize, nuts

CODEX Alimentarius is:

  1. International food standards set by WHO/FAO CODEX Commission
  2. USA only
  3. None
  4. Indian standard only
Show the answer

Answer: A. International food standards set by WHO/FAO CODEX Commission

FSSAI in India:

  1. Food export agency
  2. Ministry of food only
  3. Food Safety and Standards Authority of India
  4. None
Show the answer

Answer: C. Food Safety and Standards Authority of India Food Safety and Standards Authority of India - regulates food safety and standards

Emulsifier in food:

  1. Colour
  2. Sweetener
  3. Stabilises oil-in-water or water-in-oil emulsions
  4. Preservative
Show the answer

Answer: C. Stabilises oil-in-water or water-in-oil emulsions Stabilises oil-in-water or water-in-oil emulsions (lecithin, mono/diglycerides)

Lecithin is derived from:

  1. Milk
  2. Wheat
  3. Egg yolk or soybean
  4. None
Show the answer

Answer: C. Egg yolk or soybean Egg yolk or soybean (phospholipid emulsifier)

Stabilisers in food (e.g. xanthan gum, carrageenan):

  1. Colours
  2. Maintain texture and consistency; prevent phase separation
  3. Sweeteners
  4. Preservatives
Show the answer

Answer: B. Maintain texture and consistency; prevent phase separation

Antioxidants in food (e.g. BHA, BHT, tocopherols):

  1. Add flavour
  2. Prevent lipid oxidation and rancidity
  3. Add colour
  4. Prevent microbial growth
Show the answer

Answer: B. Prevent lipid oxidation and rancidity

Ascorbic acid (Vitamin C) in food as:

  1. Antioxidant, colour retainer, dough improver in baking
  2. Preservative only
  3. None
  4. Emulsifier
Show the answer

Answer: A. Antioxidant, colour retainer, dough improver in baking

Nitrates/nitrites in cured meats:

  1. Only flavour
  2. Only pH
  3. Only colour
  4. Prevent C. botulinum growth, fix cured meat colour, add flavour
Show the answer

Answer: D. Prevent C. botulinum growth, fix cured meat colour, add flavour

Homogenisation of milk:

  1. Skimming
  2. None
  3. Pasteurisation
  4. Reduces fat globule size to prevent cream separation
Show the answer

Answer: D. Reduces fat globule size to prevent cream separation

Butter is:

  1. Pure fat
  2. Water-in-oil emulsion made by churning cream
  3. Oil-in-water emulsion
  4. Skimmed milk
Show the answer

Answer: B. Water-in-oil emulsion made by churning cream Water-in-oil emulsion (~80% fat) made by churning cream

Cheese making involves:

  1. None
  2. Acidification, coagulation, curd cutting, pressing, and ripening
  3. Only adding acid
  4. Only heating milk
Show the answer

Answer: B. Acidification, coagulation, curd cutting, pressing, and ripening Acidification, coagulation (rennet), curd cutting, pressing, and ripening

Rennet contains:

  1. Amylase
  2. Lipase
  3. Lactase
  4. Chymosin that coagulates milk casein
Show the answer

Answer: D. Chymosin that coagulates milk casein Chymosin (protease enzyme) that coagulates milk casein

Fermented foods examples:

  1. Only wine
  2. None
  3. Only bread
  4. Yogurt, cheese, sauerkraut, kimchi, bread, beer, wine, idli, dosa
Show the answer

Answer: D. Yogurt, cheese, sauerkraut, kimchi, bread, beer, wine, idli, dosa

Lactic acid bacteria (LAB):

  1. Produce alcohol
  2. None
  3. Fix nitrogen
  4. Ferment sugars to lactic acid; used in yogurt, cheese, fermented vegetables
Show the answer

Answer: D. Ferment sugars to lactic acid; used in yogurt, cheese, fermented vegetables

Extrusion cooking:

  1. Combines mixing, cooking, shaping in extruder; produces snacks, breakfast cereals, pet food
  2. Only cooking
  3. None
  4. Only mixing
Show the answer

Answer: A. Combines mixing, cooking, shaping in extruder; produces snacks, breakfast cereals, pet food

Irradiation of food uses:

  1. UV light
  2. Gamma rays, X-rays, or electron beams to reduce microbial load
  3. Microwave
  4. None
Show the answer

Answer: B. Gamma rays, X-rays, or electron beams to reduce microbial load Gamma rays (Co-60), X-rays, or electron beams to reduce microbial load

Food irradiation does NOT:

  1. Make food radioactive
  2. Inhibit sprouting
  3. Extend shelf life
  4. Reduce microbes
Show the answer

Answer: A. Make food radioactive Make food radioactive (cannot induce radioactivity at permitted doses)

Texture profile analysis (TPA) measures:

  1. Flavour only
  2. None
  3. Colour only
  4. Hardness, cohesiveness, springiness, chewiness, gumminess of food
Show the answer

Answer: D. Hardness, cohesiveness, springiness, chewiness, gumminess of food

Rheology of food:

  1. Colour measurement
  2. None
  3. Study of flow and deformation
  4. Flavour analysis
Show the answer

Answer: C. Study of flow and deformation Study of flow and deformation - viscosity, viscoelasticity of foods

Brix (°Bx) measures:

  1. Protein content
  2. Fat content
  3. Acidity
  4. Sugar content in juice using refractometer
Show the answer

Answer: D. Sugar content in juice using refractometer Sugar content (% dissolved solids) in juice using refractometer

Retort pouch:

  1. Flexible multi-layer packaging sterilised like a can; lighter and heats faster
  2. Glass jar
  3. None
  4. Metal can
Show the answer

Answer: A. Flexible multi-layer packaging sterilised like a can; lighter and heats faster

Ohmic heating:

  1. Electrical current passed through food
  2. None
  3. Surface heating
  4. Microwave only
Show the answer

Answer: A. Electrical current passed through food Electrical current passed through food - rapid uniform volumetric heating

Pulsed Electric Field (PEF) processing:

  1. Short high-voltage pulses rupture cell membranes
  2. UV light
  3. None
  4. Microwave
Show the answer

Answer: A. Short high-voltage pulses rupture cell membranes Short high-voltage pulses rupture cell membranes - pasteurises without heat

High Pressure Processing (HPP):

  1. Only heat
  2. Only irradiation
  3. None
  4. Food subjected to 100-600 MPa
Show the answer

Answer: D. Food subjected to 100-600 MPa Food subjected to 100-600 MPa - kills pathogens without heat; preserves nutrition and colour

Ultrasound in food processing:

  1. 20-100 kHz sound waves
  2. None
  3. Only flavour
  4. Only mixing
Show the answer

Answer: A. 20-100 kHz sound waves 20-100 kHz sound waves - degassing, emulsification, inactivation of enzymes/microbes

Sous vide cooking:

  1. None
  2. Vacuum-sealed food cooked at precise low temperature in water bath for extended time
  3. High-temperature cooking
  4. Freeze-drying
Show the answer

Answer: B. Vacuum-sealed food cooked at precise low temperature in water bath for extended time

Thermophilic bacteria grow at:

  1. 45-80°C
  2. Below 20°C
  3. None
  4. Below 5°C
Show the answer

Answer: A. 45-80°C 45-80°C - relevant in pasteurised milk spoilage and yogurt fermentation

Psychrotrophic bacteria grow at:

  1. 0-7°C
  2. Above 45°C
  3. Only at 20°C
  4. None
Show the answer

Answer: A. 0-7°C 0-7°C - cause spoilage in refrigerated food (Pseudomonas, Listeria)

Listeria monocytogenes concerns:

  1. None
  2. No cold growth
  3. Grows at refrigeration temperatures; causes listeriosis
  4. Only mesophilic
Show the answer

Answer: C. Grows at refrigeration temperatures; causes listeriosis Grows at refrigeration temperatures; causes listeriosis - high risk for pregnant women, elderly

Salmonella control in poultry:

  1. Cook to internal 74°C; control cross-contamination; proper refrigeration
  2. None
  3. Irradiation only
  4. Chemical only
Show the answer

Answer: A. Cook to internal 74°C; control cross-contamination; proper refrigeration

E. coli O157:H7:

  1. Common non-pathogenic
  2. Pathogenic STEC producing Shiga toxin; found in beef, leafy greens; infective dose very low
  3. None
  4. Only from water
Show the answer

Answer: B. Pathogenic STEC producing Shiga toxin; found in beef, leafy greens; infective dose very low

Campylobacter main source:

  1. Dairy only
  2. Undercooked poultry
  3. Raw vegetables
  4. None
Show the answer

Answer: B. Undercooked poultry Undercooked poultry - leading cause of bacterial gastroenteritis in developed countries

Mycotoxin control in stored grain:

  1. Only fumigation
  2. Reduce moisture, temperature, and oxygen; proper drying and storage
  3. Chemical preservatives
  4. None
Show the answer

Answer: B. Reduce moisture, temperature, and oxygen; proper drying and storage Reduce moisture (<13%), temperature, and oxygen; proper drying and storage

Ochratoxin A produced by:

  1. Aspergillus ochraceus and Penicillium verrucosum on cereals
  2. Fusarium
  3. None
  4. Claviceps
Show the answer

Answer: A. Aspergillus ochraceus and Penicillium verrucosum on cereals Aspergillus ochraceus and Penicillium verrucosum on cereals - kidney toxin

Deoxynivalenol (DON/vomitoxin):

  1. Aflatoxin type
  2. None
  3. Ochratoxin
  4. Fusarium mycotoxin in wheat and maize; causes feed refusal in animals
Show the answer

Answer: D. Fusarium mycotoxin in wheat and maize; causes feed refusal in animals

Zearalenone:

  1. Aflatoxin
  2. Fusarium mycotoxin
  3. None
  4. Ochratoxin
Show the answer

Answer: B. Fusarium mycotoxin Fusarium mycotoxin - estrogenic activity; found in maize, wheat

Nitrites in cured meat maximum level:

  1. 50 ppm
  2. None
  3. Regulated at 100-150 ppm residual in most countries
  4. 500 ppm
Show the answer

Answer: C. Regulated at 100-150 ppm residual in most countries

Benzoic acid (sodium benzoate) as preservative:

  1. Used in meat
  2. Effective at pH < 4.5; used in fruit juices, soft drinks; inhibits yeasts and moulds
  3. Used at high pH
  4. None
Show the answer

Answer: B. Effective at pH < 4.5; used in fruit juices, soft drinks; inhibits yeasts and moulds

Sorbic acid (potassium sorbate):

  1. Only acid foods
  2. Only for yeasts
  3. Broad-spectrum preservative effective up to pH 6.5; natural origin; used in cheese, bread, wine
  4. None
Show the answer

Answer: C. Broad-spectrum preservative effective up to pH 6.5; natural origin; used in cheese, bread, wine

Propionate (calcium/sodium):

  1. Inhibits mould in bread; 'natural' in Swiss cheese
  2. None
  3. Only dairy
  4. Only bakery
Show the answer

Answer: A. Inhibits mould in bread; 'natural' in Swiss cheese Inhibits mould in bread; 'natural' in Swiss cheese (Propionibacterium fermentation)

Sulphur dioxide (SO₂) / sulphites:

  1. Antimicrobial and antioxidant; used in wine, dried fruit; must-declare allergen
  2. Only antioxidant
  3. Only antimicrobial
  4. None
Show the answer

Answer: A. Antimicrobial and antioxidant; used in wine, dried fruit; must-declare allergen

Controlled Atmosphere (CA) storage:

  1. None
  2. Same as MAP
  3. Reduces O₂, increases CO₂/N₂ in store
  4. Vacuum storage
Show the answer

Answer: C. Reduces O₂, increases CO₂/N₂ in store Reduces O₂, increases CO₂/N₂ in store - extends fresh produce life (apples, pears)

Ethylene management in cold stores:

  1. Ethylene not important
  2. None
  3. Add ethylene always
  4. Ethylene accelerates ripening; remove it to extend storage life
Show the answer

Answer: D. Ethylene accelerates ripening; remove it to extend storage life Ethylene accelerates ripening; remove it (scrubbers) to extend storage life

Cold chain:

  1. Unbroken refrigerated supply chain from production to consumer for perishables
  2. Only at storage
  3. None
  4. Only at retail
Show the answer

Answer: A. Unbroken refrigerated supply chain from production to consumer for perishables

IQF fish advantage over block frozen:

  1. Individual pieces can be separated; less thaw loss; better portion control
  2. No advantage
  3. None
  4. Only for vegetables
Show the answer

Answer: A. Individual pieces can be separated; less thaw loss; better portion control

Smoking of food:

  1. None
  2. Only flavour
  3. Only colour
  4. Deposits antimicrobial compounds on food surface; also drying effect
Show the answer

Answer: D. Deposits antimicrobial compounds on food surface; also drying effect Deposits antimicrobial compounds (phenols, aldehydes) on food surface; also drying effect

Curing salt (Prague powder):

  1. Only NaCl
  2. None
  3. Only NaNO₂
  4. Mixture of NaCl + NaNO₂
Show the answer

Answer: D. Mixture of NaCl + NaNO₂ Mixture of NaCl + NaNO₂ (6.25%) - used for cured meats

Fermentation pH drop in yogurt:

  1. Lactic acid bacteria lower pH to ~4.2-4.6; acid precipitates casein → gel texture
  2. pH rises
  3. None
  4. No pH change
Show the answer

Answer: A. Lactic acid bacteria lower pH to ~4.2-4.6; acid precipitates casein → gel texture

Whey protein vs casein:

  1. Casein ~80% of milk protein; whey ~20%
  2. None
  3. Equal proportions
  4. Whey 80%
Show the answer

Answer: A. Casein ~80% of milk protein; whey ~20% Casein ~80% of milk protein (coagulates at acid/rennet); whey ~20% (soluble, fast-digesting)

Homogenisation of milk - effect on cream line:

  1. Creates more cream
  2. Eliminates cream separation
  3. None
  4. Cream rises faster
Show the answer

Answer: B. Eliminates cream separation Eliminates cream separation - fat globules reduced to <1 µm

Skimmed milk fat content:

  1. 1.5% fat
  2. < 0.5% fat
  3. None
  4. 3.5% fat
Show the answer

Answer: B. < 0.5% fat < 0.5% fat (cream removed by centrifuge)

Full-fat milk fat content:

  1. < 0.5%
  2. ~3.5-4% fat
  3. 1-2%
  4. None
Show the answer

Answer: B. ~3.5-4% fat ~3.5-4% fat (whole milk)

Gelatinisation of starch:

  1. Dextrinisation
  2. None
  3. Retrogradation
  4. Starch granules absorb water and swell when heated → viscosity increase
Show the answer

Answer: D. Starch granules absorb water and swell when heated → viscosity increase Starch granules absorb water and swell when heated → viscosity increase (thickening)

Retrogradation of starch:

  1. Dextrinisation
  2. None
  3. Gelatinisation
  4. Reassociation of amylose/amylopectin on cooling → staling of bread, firming
Show the answer

Answer: D. Reassociation of amylose/amylopectin on cooling → staling of bread, firming

Dextrinisation (pyrodextrinisation):

  1. Gelatinisation
  2. Retrogradation
  3. Dry heat breaks starch → smaller dextrins; gives colour and flavour
  4. None
Show the answer

Answer: C. Dry heat breaks starch → smaller dextrins; gives colour and flavour Dry heat breaks starch → smaller dextrins; gives colour and flavour (toast, biscuits)

Amylose vs amylopectin:

  1. None
  2. Both linear
  3. Amylose
  4. Both branched
Show the answer

Answer: C. Amylose Amylose: linear (α-1,4 links); Amylopectin: branched (α-1,4 and α-1,6)

Waxy starches (waxy maize, waxy rice):

  1. Only linear starch
  2. Almost entirely amylopectin; don't retrograde easily; used in sauce stability
  3. None
  4. Low amylopectin
Show the answer

Answer: B. Almost entirely amylopectin; don't retrograde easily; used in sauce stability Almost entirely amylopectin (~99%); don't retrograde easily; used in sauce stability

Resistant starch (RS):

  1. Starch fraction that resists digestion in small intestine; fermented in colon like dietary fibre
  2. None
  3. Only in raw food
  4. Easily digested
Show the answer

Answer: A. Starch fraction that resists digestion in small intestine; fermented in colon like dietary fibre

Dietary fibre types:

  1. Only soluble
  2. Only insoluble
  3. None
  4. Soluble (pectin, beta-glucan
Show the answer

Answer: D. Soluble (pectin, beta-glucan Soluble (pectin, beta-glucan - lowers cholesterol) and insoluble (cellulose - gut transit)

Omega-3 fatty acids:

  1. None
  2. Saturated fats
  3. Trans fats
  4. EPA and DHA in fish oil; ALA in flaxseed; anti-inflammatory; important for brain and heart
Show the answer

Answer: D. EPA and DHA in fish oil; ALA in flaxseed; anti-inflammatory; important for brain and heart

Trans fatty acids health effects:

  1. Lower LDL
  2. No health effect
  3. Raise LDL, lower HDL
  4. None
Show the answer

Answer: C. Raise LDL, lower HDL Raise LDL, lower HDL - increase cardiovascular disease risk; WHO target elimination by 2023

Maillard browning accelerated by:

  1. High moisture
  2. Low temperature
  3. None
  4. High temperature, low moisture, alkaline pH, presence of reducing sugars and amino acids
Show the answer

Answer: D. High temperature, low moisture, alkaline pH, presence of reducing sugars and amino acids

Freezing point depression:

  1. None
  2. Raises freezing point
  3. No effect
  4. Adding solutes lowers freezing point
Show the answer

Answer: D. Adding solutes lowers freezing point Adding solutes (sugar, salt) lowers freezing point - used in ice cream formulation

Water activity of fresh meat:

  1. 0.7
  2. ~0.98-0.99 (very high
  3. 0.5
  4. 0.3
Show the answer

Answer: B. ~0.98-0.99 (very high ~0.98-0.99 (very high - highly perishable)

Intermediate moisture foods (aw 0.6-0.9):

  1. Dried fruits, jerky, soft cakes
  2. Frozen food
  3. Fresh produce
  4. None
Show the answer

Answer: A. Dried fruits, jerky, soft cakes Dried fruits, jerky, soft cakes - resistant to microbial growth without refrigeration

Aseptic processing:

  1. Pasteurisation only
  2. In-container sterilisation
  3. Product sterilised separately from packaging; filled in sterile environment
  4. None
Show the answer

Answer: C. Product sterilised separately from packaging; filled in sterile environment Product sterilised separately from packaging; filled in sterile environment - e.g. UHT milk in Tetra Pak

FSSAI maximum limits for aflatoxin:

  1. None
  2. 100 ppb
  3. 10 ppb total aflatoxins in food; 5 ppb B1 alone in some commodities
  4. 1 ppb
Show the answer

Answer: C. 10 ppb total aflatoxins in food; 5 ppb B1 alone in some commodities 10 ppb (µg/kg) total aflatoxins in food; 5 ppb B1 alone in some commodities

Glycaemic Index (GI):

  1. Calorie content
  2. Only for diabetics
  3. Rate at which food raises blood glucose compared to pure glucose
  4. None
Show the answer

Answer: C. Rate at which food raises blood glucose compared to pure glucose Rate at which food raises blood glucose compared to pure glucose (GI=100)

Sensory evaluation panel types:

  1. Machine only
  2. None
  3. Only trained panel
  4. Trained panel and consumer panel
Show the answer

Answer: D. Trained panel and consumer panel Trained panel (discrimination/descriptive) and consumer panel (preference/acceptance)

Hedonic scale (9-point):

  1. Analytical
  2. Measures degree of liking from 'dislike extremely' to 'like extremely'
  3. Descriptive only
  4. None
Show the answer

Answer: B. Measures degree of liking from 'dislike extremely' to 'like extremely'

Triangle test in sensory:

  1. None
  2. 3 samples
  3. Preference test
  4. Descriptive test
Show the answer

Answer: B. 3 samples 3 samples (2 same, 1 different) - evaluator identifies odd sample - discrimination test

Duo-trio test:

  1. None
  2. Reference + 2 samples
  3. Preference
  4. Descriptive
Show the answer

Answer: B. Reference + 2 samples Reference + 2 samples - identify which matches reference - discrimination test

QDA (Quantitative Descriptive Analysis):

  1. Discrimination only
  2. None
  3. Trained panellists rate intensity of ~10-20 sensory attributes
  4. Preference only
Show the answer

Answer: C. Trained panellists rate intensity of ~10-20 sensory attributes Trained panellists rate intensity of ~10-20 sensory attributes - detailed profile

Allergen management in food:

  1. 8 major allergens
  2. None
  3. No declaration needed
  4. Only peanuts
Show the answer

Answer: A. 8 major allergens 8 major allergens (Big 8): milk, eggs, fish, shellfish, peanuts, tree nuts, wheat, soy - must declare

Big 9 (USA 2023) allergen added:

  1. Mustard
  2. None
  3. Celery
  4. Sesame
Show the answer

Answer: D. Sesame Sesame - added as 9th major allergen requiring declaration from Jan 2023

Food fortification:

  1. Adding flavour
  2. Adding micronutrients to staple foods
  3. Adding macronutrients
  4. None
Show the answer

Answer: B. Adding micronutrients to staple foods Adding micronutrients (Fe, iodine, vitamins A/D) to staple foods - addresses hidden hunger

Iodised salt in India:

  1. Only in coastal
  2. Optional
  3. Mandatory iodisation of edible salt since 2000
  4. None
Show the answer

Answer: C. Mandatory iodisation of edible salt since 2000 Mandatory iodisation of edible salt since 2000 - prevents iodine deficiency disorders (IDD)

Double fortified salt (DFS):

  1. None
  2. Fortified with both iodine and iron
  3. Only iron
  4. Only iodine
Show the answer

Answer: B. Fortified with both iodine and iron Fortified with both iodine and iron - addresses dual deficiency common in India

Fortified rice (FRK - Fortified Rice Kernels):

  1. Coating only
  2. Rice-shaped FRKs with Fe, folic acid, vitamin B12 blended with regular rice
  3. Soaking method
  4. None
Show the answer

Answer: B. Rice-shaped FRKs with Fe, folic acid, vitamin B12 blended with regular rice Rice-shaped FRKs with Fe, folic acid, vitamin B12 blended with regular rice (1:100)

Trans fat regulation India:

  1. None
  2. 5% limit
  3. No regulation
  4. FSSAI mandated ≤2% trans fat in all oils/fats from Jan 2022
Show the answer

Answer: D. FSSAI mandated ≤2% trans fat in all oils/fats from Jan 2022 FSSAI mandated ≤2% trans fat in all oils/fats from Jan 2022 (down from 5%)

Acrylamide in food:

  1. Only from additives
  2. Not formed in food
  3. Forms in starchy foods at high temperatures
  4. None
Show the answer

Answer: C. Forms in starchy foods at high temperatures Forms in starchy foods at high temperatures (frying, baking) - potential carcinogen; reduce by process control

5-HMF (hydroxymethylfurfural):

  1. None
  2. Only in honey
  3. No health concern
  4. Forms in sugary foods when heated
Show the answer

Answer: D. Forms in sugary foods when heated Forms in sugary foods when heated - indicator of heat damage in honey, juices

Bisphenol A (BPA) in food packaging:

  1. None
  2. Safe at all levels
  3. No migration
  4. Migrates from polycarbonate and can linings
Show the answer

Answer: D. Migrates from polycarbonate and can linings Migrates from polycarbonate and can linings - endocrine disruptor; many countries restrict

PFAS in food packaging:

  1. No migration
  2. None
  3. Per- and polyfluoroalkyl substances in grease-proof packaging
  4. Not present
Show the answer

Answer: C. Per- and polyfluoroalkyl substances in grease-proof packaging Per- and polyfluoroalkyl substances in grease-proof packaging - 'forever chemicals'; being phased out

Food contact material regulation:

  1. Only for plastics
  2. No limits
  3. FCM must not migrate harmful substances >10 mg/dm²; specific migration limits for individual chemicals
  4. None
Show the answer

Answer: C. FCM must not migrate harmful substances >10 mg/dm²; specific migration limits for individual chemicals

Retort processing - sterilisation value Fo:

  1. None
  2. Fo = 1 min
  3. Fo = 100 min
  4. Fo = 3-12 min typically for low-acid foods
Show the answer

Answer: D. Fo = 3-12 min typically for low-acid foods Fo = 3-12 min typically for low-acid foods - ensures 12D botulinum cook

Shelf life testing methods:

  1. Only accelerated
  2. None
  3. Real-time storage + accelerated shelf life testing using Arrhenius or Q₁₀
  4. Only real-time
Show the answer

Answer: C. Real-time storage + accelerated shelf life testing using Arrhenius or Q₁₀ Real-time storage + accelerated shelf life testing (ASLT) using Arrhenius or Q₁₀

Food waste statistics globally:

  1. None
  2. 5%
  3. ~1/3 of all food produced is lost or wasted
  4. 10%
Show the answer

Answer: C. ~1/3 of all food produced is lost or wasted ~1/3 of all food produced (~1.3 billion tonnes/year) is lost or wasted - FAO estimate

Upcycling in food industry:

  1. None
  2. Only waste treatment
  3. Using by-products as ingredients
  4. Composting only
Show the answer

Answer: C. Using by-products as ingredients Using by-products as ingredients (e.g. whey protein, fruit pomace, brewer's spent grain)

3D food printing:

  1. No food application
  2. None
  3. Only industrial
  4. Digital control of extrusion of food materials
Show the answer

Answer: D. Digital control of extrusion of food materials Digital control of extrusion of food materials - personalised nutrition, novel structures

Clean label trend:

  1. None
  2. Complex labels
  3. More additives
  4. Consumer preference for short ingredient list without artificial additives
Show the answer

Answer: D. Consumer preference for short ingredient list without artificial additives Consumer preference for short ingredient list without artificial additives - drives natural reformulation

Plant-based meat:

  1. Lab-grown meat
  2. None
  3. Cultured meat
  4. Soy protein, pea protein, mycoprotein formulated to mimic meat texture
Show the answer

Answer: D. Soy protein, pea protein, mycoprotein formulated to mimic meat texture Soy protein, pea protein, mycoprotein formulated to mimic meat texture - growing market

Cultured/cell-based meat:

  1. Not possible
  2. Same as plant-based
  3. Animal cells grown in bioreactor
  4. None
Show the answer

Answer: C. Animal cells grown in bioreactor Animal cells grown in bioreactor - no slaughter; approved in Singapore, limited USA, Israel

Precision fermentation:

  1. Using microorganisms programmed with genes to produce specific proteins
  2. Traditional fermentation
  3. Only in beer
  4. None
Show the answer

Answer: A. Using microorganisms programmed with genes to produce specific proteins Using microorganisms programmed with genes to produce specific proteins (e.g. casein, whey) - no cows

Nutraceuticals definition:

  1. None
  2. Same as food
  3. Food or food-derived products with health benefits beyond basic nutrition
  4. Same as pharma
Show the answer

Answer: C. Food or food-derived products with health benefits beyond basic nutrition Food or food-derived products with health benefits beyond basic nutrition - grey area between food and medicine

Functional food examples:

  1. None
  2. Fortified milk, probiotic yogurt, omega-3 enriched eggs, fibre-enriched bread
  3. Only supplements
  4. All regular food
Show the answer

Answer: B. Fortified milk, probiotic yogurt, omega-3 enriched eggs, fibre-enriched bread

Prebiotics vs probiotics:

  1. Prebiotics are organisms
  2. Prebiotics
  3. None
  4. Same concept
Show the answer

Answer: B. Prebiotics Prebiotics: non-digestible fibres feeding beneficial bacteria; Probiotics: live beneficial microorganisms

Synbiotics:

  1. Combination of probiotics and prebiotics
  2. None
  3. Only probiotics
  4. Only prebiotics
Show the answer

Answer: A. Combination of probiotics and prebiotics Combination of probiotics and prebiotics - synergistic effect on gut health

Hydrodesulphurisation catalyst:

  1. CoMo or NiMo on alumina support
  2. Zeolite Y
  3. Pt
  4. V₂O₅
Show the answer

Answer: A. CoMo or NiMo on alumina support

Chlorination of methane gives:

  1. CH₃Cl, CH₂Cl₂, CHCl₃, CCl₄ (mixture
  2. None
  3. Only CCl₄
  4. Only CH₃Cl
Show the answer

Answer: A. CH₃Cl, CH₂Cl₂, CHCl₃, CCl₄ (mixture CH₃Cl, CH₂Cl₂, CHCl₃, CCl₄ (mixture - selectivity by conditions)

EDC (ethylene dichloride) is:

  1. Ethylene glycol
  2. 1,2-dichloroethane; intermediate in VCM/PVC production
  3. Ethanol
  4. None
Show the answer

Answer: B. 1,2-dichloroethane; intermediate in VCM/PVC production

Bisphenol A (BPA) synthesis:

  1. None
  2. Phenol + acetone condensation over strong acid catalyst
  3. Phenol + benzene
  4. Oxidation
Show the answer

Answer: B. Phenol + acetone condensation over strong acid catalyst Phenol + acetone (2:1) condensation over strong acid catalyst

Phosgene (COCl₂) used in:

  1. Fuel
  2. Refrigerant
  3. None
  4. Synthesis of isocyanates, polycarbonates, and pharmaceuticals
Show the answer

Answer: D. Synthesis of isocyanates, polycarbonates, and pharmaceuticals Synthesis of isocyanates (MDI, TDI), polycarbonates, and pharmaceuticals

Cyclohexane oxidation products:

  1. Benzene
  2. Styrene
  3. None
  4. KA oil; used for nylon
Show the answer

Answer: D. KA oil; used for nylon KA oil (cyclohexanone + cyclohexanol); used for nylon (adipic acid, caprolactam)

Propylene oxide (PO) production routes:

  1. None
  2. Only chlorohydrin
  3. Chlorohydrin process or HPPO or PO/SM coproduction
  4. Only HPPO
Show the answer

Answer: C. Chlorohydrin process or HPPO or PO/SM coproduction Chlorohydrin process or HPPO (H₂O₂-based) or PO/SM coproduction

Acrylic acid from acrolein:

  1. None
  2. Dehydration
  3. Hydrogenation
  4. Further oxidation of acrolein over MoV catalyst
Show the answer

Answer: D. Further oxidation of acrolein over MoV catalyst

Epichlorohydrin (ECH) production:

  1. From methane
  2. Allyl chloride + hypochlorous acid → ECH
  3. None
  4. From propylene direct
Show the answer

Answer: B. Allyl chloride + hypochlorous acid → ECH Allyl chloride + hypochlorous acid (or HPPO new route) → ECH

ECH main use:

  1. Production of epoxy resins
  2. Nylon
  3. PVC
  4. None
Show the answer

Answer: A. Production of epoxy resins Production of epoxy resins (with bisphenol A)

Maleic anhydride from n-butane:

  1. None
  2. Partial oxidation over V-P-O catalyst
  3. From butadiene
  4. From benzene only
Show the answer

Answer: B. Partial oxidation over V-P-O catalyst Partial oxidation over V-P-O (vanadium phosphorus oxide) catalyst

Caprolactam Beckmann rearrangement uses:

  1. Cyclohexanone oxime + oleum → caprolactam
  2. HCl
  3. HNO₃
  4. HF
Show the answer

Answer: A. Cyclohexanone oxime + oleum → caprolactam Cyclohexanone oxime + oleum (H₂SO₄) → caprolactam

Titanium dioxide (TiO₂) - chloride process:

  1. TiCl₄ + O₂ → TiO₂ + Cl₂
  2. Sulphate process
  3. None
  4. Wet process
Show the answer

Answer: A. TiCl₄ + O₂ → TiO₂ + Cl₂ TiCl₄ + O₂ → TiO₂ + Cl₂ (higher purity rutile product)

Sodium silicate (water glass) produced from:

  1. None
  2. SiO₂ + Na₂CO₃ fusion in furnace
  3. Acid process
  4. Electrolysis
Show the answer

Answer: B. SiO₂ + Na₂CO₃ fusion in furnace

Zeolite synthesis:

  1. Hydrothermal crystallisation of aluminosilicate gels at 100-200°C
  2. None
  3. Wet mixing only
  4. Fusion only
Show the answer

Answer: A. Hydrothermal crystallisation of aluminosilicate gels at 100-200°C

Catalyst poisoning means:

  1. Temperature effect
  2. Irreversible deactivation by strong adsorption of impurity on active sites
  3. None
  4. Temporary slowing
Show the answer

Answer: B. Irreversible deactivation by strong adsorption of impurity on active sites Irreversible deactivation by strong adsorption of impurity on active sites (e.g. S poisons Ni)

Catalyst sintering means:

  1. Fouling
  2. None
  3. Poisoning
  4. Loss of active surface area due to high-temperature crystallite agglomeration
Show the answer

Answer: D. Loss of active surface area due to high-temperature crystallite agglomeration

Coking on catalyst surface:

  1. None
  2. Carbon deposition blocking active sites
  3. Poisoning
  4. Permanent deactivation
Show the answer

Answer: B. Carbon deposition blocking active sites Carbon deposition blocking active sites - removed by regeneration (burning)

Paraxylene separation from xylene mixture:

  1. Distillation only
  2. Extraction only
  3. Crystallisation or adsorption
  4. None
Show the answer

Answer: C. Crystallisation or adsorption Crystallisation or adsorption (Parex process using simulated moving bed on zeolite)

Coke ovens produce:

  1. Metallurgical coke + coal tar, coal gas, benzole
  2. Only coke
  3. Only gas
  4. None
Show the answer

Answer: A. Metallurgical coke + coal tar, coal gas, benzole Metallurgical coke + coal tar, coal gas, benzole (from coal carbonisation)

Coal gasification:

  1. Coal + N₂ → ammonia
  2. None
  3. Coal + O₂/steam → CO + H₂ at high T and P
  4. Coal + H₂ → methane
Show the answer

Answer: C. Coal + O₂/steam → CO + H₂ at high T and P Coal + O₂/steam → CO + H₂ (syngas) at high T and P

Underground Coal Gasification (UCG):

  1. Hydrogenation
  2. Surface gasification
  3. In-situ gasification of coal seam without mining
  4. None
Show the answer

Answer: C. In-situ gasification of coal seam without mining

Polymerisation of ethylene to HDPE:

  1. Only high P radical
  2. None
  3. Ziegler-Natta or Philips or metallocene catalyst at low P
  4. Only high T
Show the answer

Answer: C. Ziegler-Natta or Philips or metallocene catalyst at low P Ziegler-Natta (TiCl₄/AlEt₃) or Philips (CrO₃/SiO₂) or metallocene catalyst at low P

LDPE polymerisation:

  1. Low pressure
  2. Free radical polymerisation at 1500-3000 bar, 150-300°C
  3. None
  4. Ziegler-Natta
Show the answer

Answer: B. Free radical polymerisation at 1500-3000 bar, 150-300°C Free radical polymerisation at 1500-3000 bar, 150-300°C - highly branched

LLDPE production:

  1. Low pressure Ziegler-Natta or metallocene with comonomer
  2. None
  3. High pressure radical
  4. Ionic polymerisation
Show the answer

Answer: A. Low pressure Ziegler-Natta or metallocene with comonomer Low pressure Ziegler-Natta or metallocene with comonomer (butene, hexene, octene)

Propylene to polypropylene:

  1. None
  2. Ziegler-Natta gives isotactic PP
  3. Ionic only
  4. Free radical
Show the answer

Answer: B. Ziegler-Natta gives isotactic PP Ziegler-Natta (TiCl₃/AlEt₂Cl) gives isotactic PP - stereoregular

Metallocene catalysts advantage over Ziegler-Natta:

  1. Less activity
  2. Single-site catalyst
  3. None
  4. Broader MWD
Show the answer

Answer: B. Single-site catalyst Single-site catalyst - narrow MWD, controlled comonomer insertion, novel architectures

Ring-opening metathesis polymerisation (ROMP):

  1. Addition only
  2. Cyclic olefins opened by Grubbs catalyst to form polymers
  3. Free radical
  4. None
Show the answer

Answer: B. Cyclic olefins opened by Grubbs catalyst to form polymers

ATOM Transfer Radical Polymerisation (ATRP):

  1. None
  2. Controlled radical polymerisation giving narrow MWD
  3. Ionic
  4. Conventional radical
Show the answer

Answer: B. Controlled radical polymerisation giving narrow MWD Controlled radical polymerisation giving narrow MWD - copper-based catalyst

Anionic polymerisation:

  1. Cationic
  2. None
  3. Living polymerisation
  4. Free radical
Show the answer

Answer: C. Living polymerisation Living polymerisation - no termination, narrow MWD, makes block copolymers

Nylon 6,6 condensation:

  1. Addition
  2. Ring opening
  3. None
  4. Adipic acid + hexamethylenediamine → nylon 6,6 + H₂O
Show the answer

Answer: D. Adipic acid + hexamethylenediamine → nylon 6,6 + H₂O Adipic acid + hexamethylenediamine → nylon 6,6 + H₂O - stepwise condensation

Polyester PET condensation:

  1. None
  2. EG + PTA → PET + H₂O (two stage
  3. Addition polymerisation
  4. Ring opening
Show the answer

Answer: B. EG + PTA → PET + H₂O (two stage EG + PTA → PET + H₂O (two stage: esterification then polycondensation)

Polycarbonate synthesis (interfacial):

  1. Bulk polymerisation
  2. BPA + phosgene in two-phase solvent/water system with base
  3. Solution only
  4. None
Show the answer

Answer: B. BPA + phosgene in two-phase solvent/water system with base

Epoxy resin curing:

  1. Thermoplastic
  2. UV only
  3. Epoxide groups react with amine hardener
  4. None
Show the answer

Answer: C. Epoxide groups react with amine hardener Epoxide groups react with amine hardener (or anhydride) - cross-linked thermoset

Silicone rubber (PDMS) curing:

  1. Thermal only
  2. None
  3. UV only
  4. Condensation or addition cross-linking
Show the answer

Answer: D. Condensation or addition cross-linking Condensation (moisture cure) or addition (Pt catalyst) cross-linking

Thermoplastic elastomers (TPE):

  1. Materials with rubber-like properties that can be processed as thermoplastics
  2. None
  3. Always crosslinked
  4. Always thermosets
Show the answer

Answer: A. Materials with rubber-like properties that can be processed as thermoplastics Materials with rubber-like properties that can be processed as thermoplastics (no vulcanisation)

SBS (styrene-butadiene-styrene) block copolymer:

  1. Single polymer
  2. None
  3. TPE
  4. Random copolymer
Show the answer

Answer: C. TPE TPE - hard PS blocks act as physical cross-links in soft PB matrix

Wacker oxidation:

  1. Haber process
  2. None
  3. Fischer-Tropsch
  4. Ethylene + O₂ → acetaldehyde using PdCl₂/CuCl₂ catalyst in water
Show the answer

Answer: D. Ethylene + O₂ → acetaldehyde using PdCl₂/CuCl₂ catalyst in water

Diels-Alder reaction (industrial):

  1. None
  2. Nucleophilic
  3. Diene + dienophile [4+2] cycloaddition
  4. Radical addition
Show the answer

Answer: C. Diene + dienophile [4+2] cycloaddition Diene + dienophile [4+2] cycloaddition - makes cyclohexene derivatives (norbornene, THPA)

Sulfonation of LAB (Linear Alkylbenzene):

  1. LAB + SO₃ or oleum → LABS
  2. None
  3. Chlorination
  4. Oxidation
Show the answer

Answer: A. LAB + SO₃ or oleum → LABS LAB + SO₃ or oleum → LABS (linear alkylbenzene sulphonate) - anionic surfactant

Ethoxylation of fatty alcohol:

  1. Condensation
  2. RCH₂OH + n EO → RCH₂nOH
  3. None
  4. Free radical
Show the answer

Answer: B. RCH₂OH + n EO → RCH₂nOH RCH₂OH + n EO → RCH₂(OCH₂CH₂)nOH - nonionic surfactant

Industrial enzyme applications:

  1. Only pharma
  2. Proteases, amylases, lipases, cellulases
  3. Only food
  4. None
Show the answer

Answer: B. Proteases, amylases, lipases, cellulases Proteases (detergents), amylases (baking, starch), lipases (leather, food), cellulases (textiles)

Fermentation media components:

  1. None
  2. Only water
  3. Only sugar
  4. Carbon source, nitrogen source, minerals, vitamins, growth factors, and water at controlled T, pH
Show the answer

Answer: D. Carbon source, nitrogen source, minerals, vitamins, growth factors, and water at controlled T, pH

Continuous stirred tank reactor (CSTR) for fermentation:

  1. None
  2. PFR for fermentation
  3. Batch only
  4. Steady-state operation; constant product quality; good for kinetics-controlled reactions
Show the answer

Answer: D. Steady-state operation; constant product quality; good for kinetics-controlled reactions

Fed-batch fermentation:

  1. Fixed batch
  2. None
  3. Substrate added in controlled manner
  4. Continuous only
Show the answer

Answer: C. Substrate added in controlled manner Substrate added in controlled manner - avoids substrate inhibition; higher productivity than batch

Downstream processing in biotech:

  1. Only fermentation
  2. None
  3. Only upstream
  4. Cell disruption, centrifugation, filtration, chromatography, crystallisation
Show the answer

Answer: D. Cell disruption, centrifugation, filtration, chromatography, crystallisation Cell disruption, centrifugation, filtration, chromatography, crystallisation - purification steps

Chromatography types in bioprocessing:

  1. Only GC
  2. None
  3. Ion exchange, size exclusion, affinity, hydrophobic interaction chromatography
  4. Only HPLC
Show the answer

Answer: C. Ion exchange, size exclusion, affinity, hydrophobic interaction chromatography Ion exchange, size exclusion (SEC/GFC), affinity, hydrophobic interaction chromatography (HIC)

Good Manufacturing Practice (GMP):

  1. Only for food
  2. None
  3. Only for chemicals
  4. Quality system ensuring pharmaceutical products are consistently produced and controlled to quality standards
Show the answer

Answer: D. Quality system ensuring pharmaceutical products are consistently produced and controlled to quality standards

ICH guidelines for pharmaceuticals:

  1. Optional
  2. International Council for Harmonisation
  3. None
  4. National only
Show the answer

Answer: B. International Council for Harmonisation International Council for Harmonisation - Q, S, E guidelines for quality, safety, efficacy

API (Active Pharmaceutical Ingredient):

  1. None
  2. Carrier
  3. Excipient
  4. Active ingredient in drug formulation that produces therapeutic effect
Show the answer

Answer: D. Active ingredient in drug formulation that produces therapeutic effect

Pharma India - bulk drug capital:

  1. Hyderabad; Ahmedabad, Vapi also important
  2. None
  3. Mumbai only
  4. Delhi only
Show the answer

Answer: A. Hyderabad; Ahmedabad, Vapi also important Hyderabad (HMDA pharma cluster); Ahmedabad, Vapi also important

India's pharma exports:

  1. None
  2. ~$25 billion
  3. $100 billion
  4. $5 billion
Show the answer

Answer: B. ~$25 billion ~$25 billion (2023-24) - generic medicines; India = 'pharmacy of the world'

Jan Aushadhi Kendras:

  1. Generic medicine stores selling affordable medicines under PM-BJP scheme
  2. None
  3. Hospital pharmacy
  4. Only rural
Show the answer

Answer: A. Generic medicine stores selling affordable medicines under PM-BJP scheme

CDSCO (Central Drugs Standard Control Organisation):

  1. None
  2. India's regulatory authority for pharmaceuticals and medical devices
  3. BIS function
  4. FSSAI function
Show the answer

Answer: B. India's regulatory authority for pharmaceuticals and medical devices India's regulatory authority for pharmaceuticals and medical devices (under MoHFW)

IND (Investigational New Drug) application:

  1. Filed before Phase I clinical trials to get regulatory approval to test drug in humans
  2. Post-market
  3. After approval
  4. None
Show the answer

Answer: A. Filed before Phase I clinical trials to get regulatory approval to test drug in humans

Phase I clinical trials:

  1. Large population
  2. Efficacy trial
  3. First-in-human
  4. None
Show the answer

Answer: C. First-in-human First-in-human - safety, tolerability, pharmacokinetics in small healthy volunteer group (~20-80)

Phase III clinical trials:

  1. Small group
  2. None
  3. Safety only
  4. Large randomised controlled trials for efficacy and safety
Show the answer

Answer: D. Large randomised controlled trials for efficacy and safety Large randomised controlled trials (hundreds-thousands patients) for efficacy and safety

Generic drug bioequivalence:

  1. Same formulation required
  2. None
  3. New safety studies needed
  4. Demonstrated by bioequivalence studies
Show the answer

Answer: D. Demonstrated by bioequivalence studies Demonstrated by bioequivalence studies - AUC and Cmax within 80-125% of innovator drug

DMPK (Drug Metabolism and Pharmacokinetics):

  1. Only absorption
  2. ADME
  3. Only metabolism
  4. None
Show the answer

Answer: B. ADME ADME - Absorption, Distribution, Metabolism, Excretion - key in drug development

CYP450 enzymes:

  1. Major drug-metabolising enzymes in liver
  2. Synthetic enzymes
  3. None
  4. Plant enzymes
Show the answer

Answer: A. Major drug-metabolising enzymes in liver Major drug-metabolising enzymes in liver - CYP3A4 most important (metabolises ~50% of drugs)

Acetaldehyde from ethanol (older route):

  1. [
  2. "
  3. x
  4. O
Show the answer

Answer: A. [

Acrolein industrial uses:

  1. e
  2. "
  3. [
  4. M
Show the answer

Answer: C. [

Maleic anhydride from butane selectivity challenge:

  1. "
  2. P
  3. [
  4. a
Show the answer

Answer: C. [

Cyclohexane oxidation selectivity:

  1. e
  2. K
  3. [
  4. "
Show the answer

Answer: C. [

Adipic acid from KA oil oxidation:

  1. "
  2. A
  3. [
  4. K
Show the answer

Answer: C. [

Beckmann rearrangement catalyst:

  1. u
  2. [
  3. "
  4. F
Show the answer

Answer: B. [

MDI vs TDI applications:

  1. M
  2. [
  3. D
  4. "
Show the answer

Answer: B. [

Nitrobenzene hydrogenation - aniline route:

  1. [
  2. C
  3. "
  4. a
Show the answer

Answer: A. [

Cumene peroxidation conditions:

  1. [
  2. i
  3. A
  4. "
Show the answer

Answer: A. [

Hock rearrangement conditions:

  1. C
  2. "
  3. H
  4. [
Show the answer

Answer: D. [

Wacker process mechanism:

  1. "
  2. [
  3. P
  4. d
Show the answer

Answer: B. [

Metathesis catalyst (Grubbs):

  1. R
  2. "
  3. [
  4. u
Show the answer

Answer: C. [

Sharpless epoxidation:

  1. [
  2. A
  3. s
  4. "
Show the answer

Answer: A. [

Industrial biotransformations:

  1. L
  2. [
  3. i
  4. "
Show the answer

Answer: B. [

Acrylamide industrial production:

  1. [
  2. y
  3. "
  4. H
Show the answer

Answer: A. [

Methyl methacrylate (MMA) production:

  1. [
  2. A
  3. C
  4. "
Show the answer

Answer: A. [

Perspex/PMMA from MMA:

  1. [
  2. "
  3. F
  4. r
Show the answer

Answer: A. [

Succinic acid bio-production:

  1. "
  2. [
  3. e
  4. F
Show the answer

Answer: B. [

1,3-BDO (1,3-Butanediol) bio-route:

  1. "
  2. e
  3. [
  4. F
Show the answer

Answer: C. [

Levulinic acid production:

  1. c
  2. [
  3. "
  4. A
Show the answer

Answer: B. [

HMF (5-hydroxymethylfurfural):

  1. D
  2. e
  3. "
  4. [
Show the answer

Answer: D. [

PEF (polyethylene furanoate):

  1. [
  2. B
  3. i
  4. "
Show the answer

Answer: A. [

PDO (1,3-propanediol) bio-production:

  1. "
  2. D
  3. u
  4. [
Show the answer

Answer: D. [

PTT (polytrimethylene terephthalate):

  1. C
  2. "
  3. o
  4. [
Show the answer

Answer: D. [

Biogas composition:

  1. C
  2. [
  3. "
  4. H
Show the answer

Answer: B. [

Syngas cleaning for FT synthesis:

  1. "
  2. [
  3. R
  4. e
Show the answer

Answer: B. [

Cobalt vs iron FT catalyst:

  1. [
  2. o
  3. C
  4. "
Show the answer

Answer: A. [

Slurry bubble column reactor for FT:

  1. a
  2. C
  3. "
  4. [
Show the answer

Answer: D. [

Lurgi dry-ash gasifier:

  1. M
  2. o
  3. [
  4. "
Show the answer

Answer: C. [

Shell SCGP (Shell Coal Gasification Process):

  1. [
  2. n
  3. "
  4. E
Show the answer

Answer: A. [

The BHC (green) process for Ibuprofen synthesis reduces the number of steps to:

  1. 6 steps
  2. 3 steps
  3. 10 steps
  4. 14 steps
Show the answer

Answer: B. 3 steps

Paclitaxel (Taxol) semi-synthesis:

  1. t
  2. [
  3. "
  4. S
Show the answer

Answer: B. [

Continuous manufacturing in pharma:

  1. "
  2. [
  3. R
  4. e
Show the answer

Answer: B. [

PAT (Process Analytical Technology) in pharma:

  1. R
  2. e
  3. [
  4. "
Show the answer

Answer: C. [

QbD (Quality by Design) approach:

  1. e
  2. D
  3. "
  4. [
Show the answer

Answer: D. [

Biocatalysis selectivity advantage:

  1. None
  2. Less selective
  3. Same as chemical
  4. Enzymes show regio-, stereo-, and chemoselectivity
Show the answer

Answer: D. Enzymes show regio-, stereo-, and chemoselectivity Enzymes show regio-, stereo-, and chemoselectivity - minimal by-products vs chemical synthesis

Continuous flow chemistry advantages:

  1. Better heat/mass transfer, safer for exothermic reactions, smaller scale, easy to scale by numbering up
  2. Less safe
  3. Same as batch
  4. None
Show the answer

Answer: A. Better heat/mass transfer, safer for exothermic reactions, smaller scale, easy to scale by numbering up

Paint consists of:

  1. Pigment, binder, solvent, and additives
  2. Only pigment and solvent
  3. Only binder
  4. None
Show the answer

Answer: A. Pigment, binder, solvent, and additives Pigment, binder (vehicle), solvent, and additives

Binder (vehicle) in paint:

  1. Pigment
  2. Thinner
  3. Film-forming polymer that holds pigment and adheres to surface
  4. Solvent
Show the answer

Answer: C. Film-forming polymer that holds pigment and adheres to surface Film-forming polymer that holds pigment and adheres to surface (alkyd, acrylic, epoxy)

Pigment in paint:

  1. Evaporates
  2. Acts as binder
  3. Provides colour, opacity, and sometimes corrosion protection
  4. Dissolves substrate
Show the answer

Answer: C. Provides colour, opacity, and sometimes corrosion protection

TiO₂ (titanium dioxide) is used as:

  1. Extender
  2. White pigment
  3. Colour pigment
  4. Binder
Show the answer

Answer: B. White pigment White pigment - highest hiding power (opacity) due to high refractive index (~2.7)

Extenders (fillers) in paint:

  1. Binders
  2. Pigments
  3. Low-cost inorganic materials
  4. Solvents
Show the answer

Answer: C. Low-cost inorganic materials Low-cost inorganic materials (CaCO₃, BaSO₄, talc, kaolin) - reduce cost, control rheology

Alkyd resin paint:

  1. Solvent-free
  2. Thermoplastic
  3. Oil-modified polyester; most widely used binder in decorative paints; air-drying
  4. Water-based only
Show the answer

Answer: C. Oil-modified polyester; most widely used binder in decorative paints; air-drying

Alkyd resin made from:

  1. Polyol + dibasic acid + drying oil
  2. None
  3. Only polyol
  4. Only phthalic anhydride
Show the answer

Answer: A. Polyol + dibasic acid + drying oil Polyol (glycerol/pentaerythritol) + dibasic acid (phthalic anhydride) + drying oil

Oil length of alkyd resin:

  1. % solvent
  2. % of drying oil in resin; long oil flexible; short oil fast drying
  3. % pigment
  4. None
Show the answer

Answer: B. % of drying oil in resin; long oil flexible; short oil fast drying % of drying oil in resin; long oil (>60%) flexible; short oil (<40%) fast drying

Drying oils (e.g. linseed oil) cure by:

  1. Hydrolysis
  2. None
  3. Evaporation
  4. Oxidative polymerisation with atmospheric O₂
Show the answer

Answer: D. Oxidative polymerisation with atmospheric O₂ Oxidative polymerisation (autoxidation) with atmospheric O₂ - cross-linking

Driers (siccatives) in alkyd paints:

  1. Slow curing
  2. Add colour
  3. Metal salts that catalyse oxidative drying
  4. Thicken paint
Show the answer

Answer: C. Metal salts that catalyse oxidative drying Metal salts (Co, Mn, Zr naphthenates) that catalyse oxidative drying

Acrylic paint (water-based emulsion):

  1. None
  2. Solvent-based
  3. Acrylic polymer latex dispersed in water; low VOC; fast drying
  4. Oil-based
Show the answer

Answer: C. Acrylic polymer latex dispersed in water; low VOC; fast drying

Epoxy paint:

  1. None
  2. Air-drying
  3. Single component
  4. Two-component; chemical-resistant, hard, used in industrial coatings
Show the answer

Answer: D. Two-component; chemical-resistant, hard, used in industrial coatings Two-component (resin + hardener/amine); chemical-resistant, hard, used in industrial coatings

Polyurethane (PU) paint:

  1. 2K or 1K; hard, flexible, durable; used in automotive, marine
  2. None
  3. Alkyd-based
  4. Epoxy-based
Show the answer

Answer: A. 2K or 1K; hard, flexible, durable; used in automotive, marine 2K (isocyanate + polyol) or 1K; hard, flexible, durable; used in automotive, marine

Chlorinated rubber paint:

  1. Good chemical and water resistance; used in swimming pools, marine
  2. Only decorative
  3. Poor chemical resistance
  4. None
Show the answer

Answer: A. Good chemical and water resistance; used in swimming pools, marine

Cellulose nitrate (lacquer):

  1. None
  2. Fast-drying by solvent evaporation only; used in wood furniture finishing
  3. Air oxidation
  4. Two-component
Show the answer

Answer: B. Fast-drying by solvent evaporation only; used in wood furniture finishing

VOC (Volatile Organic Compound) regulations:

  1. Limit TiO₂
  2. Limit pigment
  3. Limit solvent content in paints to reduce air pollution; driving shift to water-based
  4. None
Show the answer

Answer: C. Limit solvent content in paints to reduce air pollution; driving shift to water-based

Critical Pigment Volume Concentration (CPVC):

  1. Total pigment %
  2. PVC at which there is just enough binder to fill voids between pigment particles
  3. None
  4. Binder %
Show the answer

Answer: B. PVC at which there is just enough binder to fill voids between pigment particles PVC at which there is just enough binder to fill voids between pigment particles - properties change above CPVC

PVC (Pigment Volume Concentration):

  1. None
  2. Mass ratio
  3. Cost ratio
  4. Volume of pigment / × 100%
Show the answer

Answer: D. Volume of pigment / × 100% Volume of pigment / (volume of pigment + volume of binder) × 100%

Hiding power (opacity) measured by:

  1. Contrast ratio or scattering coefficient
  2. None
  3. Gloss measurement
  4. Viscosity
Show the answer

Answer: A. Contrast ratio or scattering coefficient Contrast ratio (reflectance over black / reflectance over white) or scattering coefficient

Gloss of paint depends on:

  1. None
  2. Colour only
  3. Pigment size only
  4. Smoothness of film surface; measured at 20°, 60°, or 85° gloss angles
Show the answer

Answer: D. Smoothness of film surface; measured at 20°, 60°, or 85° gloss angles

High PVC above CPVC gives:

  1. Matt finish; porous film; poor washability
  2. Good barrier
  3. Glossy finish
  4. None
Show the answer

Answer: A. Matt finish; porous film; poor washability Matt (flat) finish; porous film; poor washability

Low PVC (well below CPVC):

  1. Matt finish
  2. None
  3. Porous film
  4. Glossy, impermeable, durable film
Show the answer

Answer: D. Glossy, impermeable, durable film

Alkali resistance required for:

  1. Metal substrate
  2. Paints applied on new concrete/plaster
  3. None
  4. Wood substrate
Show the answer

Answer: B. Paints applied on new concrete/plaster Paints applied on new concrete/plaster (alkaline substrate)

Anti-corrosive primer pigments:

  1. None
  2. TiO₂
  3. Zinc phosphate, zinc chromate, red lead, zinc dust
  4. Carbon black
Show the answer

Answer: C. Zinc phosphate, zinc chromate, red lead, zinc dust Zinc phosphate, zinc chromate (being phased out), red lead (phased out), zinc dust

Zinc-rich primer:

  1. None
  2. No zinc
  3. Low zinc
  4. High zinc dust loading for galvanic corrosion protection of steel
Show the answer

Answer: D. High zinc dust loading for galvanic corrosion protection of steel High zinc dust loading (>80% in dry film) for galvanic corrosion protection of steel

Intumescent coatings:

  1. Expand when heated to form insulating char, protecting steel from fire for specified time
  2. Normal paint
  3. Non-expanding
  4. None
Show the answer

Answer: A. Expand when heated to form insulating char, protecting steel from fire for specified time

Marine anti-fouling paint:

  1. Decorative only
  2. Prevents barnacles and algae growth on ship hulls
  3. None
  4. Primer only
Show the answer

Answer: B. Prevents barnacles and algae growth on ship hulls Prevents barnacles and algae growth on ship hulls - contains biocides

Self-polishing copolymer (SPC) anti-fouling:

  1. Seawater reacts with polymer to continuously release biocide and smooth hull
  2. Static release
  3. None
  4. One-time release
Show the answer

Answer: A. Seawater reacts with polymer to continuously release biocide and smooth hull

Rheology modifiers (thickeners) in paint:

  1. Binders
  2. Pigments
  3. Hydroxyethyl cellulose, bentonite, fumed silica
  4. Solvents
Show the answer

Answer: C. Hydroxyethyl cellulose, bentonite, fumed silica Hydroxyethyl cellulose (HEC), bentonite, fumed silica - control sag and levelling

Dispersing agents (surfactants) in paint:

  1. Thickeners
  2. Solvents
  3. Stabilise pigment dispersion; prevent flocculation and settling
  4. Binders
Show the answer

Answer: C. Stabilise pigment dispersion; prevent flocculation and settling

Coalescent in waterborne paints:

  1. Pigment
  2. Binder
  3. Thickener
  4. Helps latex particles fuse at ambient temperature to form continuous film
Show the answer

Answer: D. Helps latex particles fuse at ambient temperature to form continuous film

Minimum film formation temperature (MFFT):

  1. Maximum T
  2. Lowest T at which latex forms a continuous film; coalescents lower MFFT
  3. Drying T
  4. None
Show the answer

Answer: B. Lowest T at which latex forms a continuous film; coalescents lower MFFT

Flash point of paint:

  1. Melting point
  2. Temperature at which vapours ignite; important for fire safety and transport classification
  3. None
  4. Boiling point
Show the answer

Answer: B. Temperature at which vapours ignite; important for fire safety and transport classification

Viscosity measurement in paint industry:

  1. Only centipoise
  2. Krebs units, stormer viscometer; also ICI cone & plate for high shear
  3. None
  4. Pascal seconds only
Show the answer

Answer: B. Krebs units, stormer viscometer; also ICI cone & plate for high shear Krebs units (KU), stormer viscometer; also ICI cone & plate for high shear

Fineness of grind (FOG):

  1. Density
  2. Measures largest particle size / agglomerate in paint (Hegman gauge
  3. None
  4. Film thickness
Show the answer

Answer: B. Measures largest particle size / agglomerate in paint (Hegman gauge Measures largest particle size / agglomerate in paint (Hegman gauge: 0=coarse, 8=fine)

Paint film defects - sagging:

  1. Paint running down vertical surface due to too-low viscosity or thick application
  2. None
  3. Cratering
  4. Blushing
Show the answer

Answer: A. Paint running down vertical surface due to too-low viscosity or thick application

Cratering defect in paint:

  1. Sagging
  2. Small craters caused by contamination or gas bubbles breaking surface
  3. None
  4. Blushing
Show the answer

Answer: B. Small craters caused by contamination or gas bubbles breaking surface Small craters caused by contamination (silicone, oil) or gas bubbles breaking surface

Blushing defect:

  1. Sagging
  2. Milky appearance in lacquers due to moisture condensation during fast evaporation
  3. Cratering
  4. None
Show the answer

Answer: B. Milky appearance in lacquers due to moisture condensation during fast evaporation

Chalking of paint film:

  1. Good UV resistance
  2. Water resistance
  3. Surface degradation by UV
  4. None
Show the answer

Answer: C. Surface degradation by UV Surface degradation by UV - pigment particles exposed on surface (powdery)

Adhesion promoters:

  1. Solvents
  2. None
  3. Silane coupling agents or tie-coat primers to improve coating adhesion to substrate
  4. Pigments
Show the answer

Answer: C. Silane coupling agents or tie-coat primers to improve coating adhesion to substrate

Powder coatings:

  1. None
  2. Solvent-based
  3. Solvent-free; applied electrostatically as dry powder; cured by heat; zero VOC
  4. Liquid coatings
Show the answer

Answer: C. Solvent-free; applied electrostatically as dry powder; cured by heat; zero VOC

Electrostatic spray application:

  1. Random deposition
  2. None
  3. Low efficiency
  4. Charged paint particles attracted to grounded substrate
Show the answer

Answer: D. Charged paint particles attracted to grounded substrate Charged paint particles attracted to grounded substrate - high transfer efficiency

Cathodic electrodeposition (E-coat):

  1. Component dipped in paint bath; film deposited by electric current; used for car bodies
  2. Anodic only
  3. Spray only
  4. None
Show the answer

Answer: A. Component dipped in paint bath; film deposited by electric current; used for car bodies Component (cathode) dipped in paint bath; film deposited by electric current; used for car bodies

Paint film thickness measured by:

  1. Weight only
  2. Visual only
  3. Dry Film Thickness gauge
  4. None
Show the answer

Answer: C. Dry Film Thickness gauge Dry Film Thickness (DFT) gauge - magnetic or eddy current on metal substrates

Cross-cut adhesion test:

  1. Tensile test
  2. Grid of cuts through film; tape applied and pulled
  3. Impact test
  4. None
Show the answer

Answer: B. Grid of cuts through film; tape applied and pulled Grid of cuts through film; tape applied and pulled - rates adhesion 0-5 (ISO 2409)

Salt spray test:

  1. Accelerated corrosion resistance test
  2. UV test
  3. Heat test
  4. None
Show the answer

Answer: A. Accelerated corrosion resistance test Accelerated corrosion resistance test - exposed to 5% NaCl mist at 35°C

UV weatherometer test:

  1. Accelerated weathering using UV light and moisture cycles to simulate outdoor exposure
  2. Thermal only
  3. Salt spray
  4. None
Show the answer

Answer: A. Accelerated weathering using UV light and moisture cycles to simulate outdoor exposure

BIS standards for paints in India:

  1. None
  2. ISO only
  3. ASTM only
  4. Bureau of Indian Standards
Show the answer

Answer: D. Bureau of Indian Standards Bureau of Indian Standards (BIS) - IS codes for various paints

Solvent blend in paint - high boiling solvents (retarders):

  1. Reduce viscosity only
  2. Slow evaporation to improve flow and levelling
  3. None
  4. Fast drying
Show the answer

Answer: B. Slow evaporation to improve flow and levelling

Linseed oil in paint is a:

  1. Drying oil
  2. Solvent
  3. Thinner
  4. Non-drying oil
Show the answer

Answer: A. Drying oil Drying oil - oxidises and polymerises to form tough film

Iodine value measures:

  1. Viscosity
  2. None
  3. Acid value
  4. Degree of unsaturation of oil
Show the answer

Answer: D. Degree of unsaturation of oil Degree of unsaturation of oil - higher value = more unsaturated = faster drying

Acid value of oil measures:

  1. None
  2. Drying speed
  3. Unsaturation
  4. Free fatty acid content
Show the answer

Answer: D. Free fatty acid content Free fatty acid content - lower is better for paint binders

Saponification value:

  1. Iodine value
  2. Acid value
  3. None
  4. Number of mg KOH to saponify 1 g of oil
Show the answer

Answer: D. Number of mg KOH to saponify 1 g of oil Number of mg KOH to saponify 1 g of oil - indicates average molecular weight

Oil length of alkyd resin:

  1. Long oil = flexible, slow dry; short oil = hard, fast dry
  2. Only viscosity measure
  3. None
  4. Color index
Show the answer

Answer: A. Long oil = flexible, slow dry; short oil = hard, fast dry Long oil (>60% oil) = flexible, slow dry; short oil (<40%) = hard, fast dry

Phthalic anhydride in alkyd resins:

  1. Provides backbone rigidity and hardness via ester linkages
  2. Acts as solvent
  3. Acts as pigment
  4. None
Show the answer

Answer: A. Provides backbone rigidity and hardness via ester linkages

Glycerol (glycerin) in alkyd resins:

  1. Solvent
  2. Pigment dispersant
  3. None
  4. Polyol component providing branching points for esterification
Show the answer

Answer: D. Polyol component providing branching points for esterification

Epoxy paint curing agent:

  1. Polyamine or polyamide
  2. Only heat
  3. Solvent only
  4. None
Show the answer

Answer: A. Polyamine or polyamide Polyamine or polyamide (crosslinks epoxy groups)

Zinc-rich primer works by:

  1. None
  2. Galvanic protection
  3. Barrier protection only
  4. Oxygen scavenging
Show the answer

Answer: B. Galvanic protection Galvanic protection - zinc sacrificially corrodes to protect steel

Red lead (Pb₃O₄) primer:

  1. None
  2. Modern standard
  3. Still widely used
  4. Traditional anti-corrosive pigment
Show the answer

Answer: D. Traditional anti-corrosive pigment Traditional anti-corrosive pigment (now restricted due to Pb toxicity)

VOC (Volatile Organic Compound) in paint:

  1. Binders
  2. Solvents that evaporate during drying
  3. None
  4. Pigments
Show the answer

Answer: B. Solvents that evaporate during drying Solvents that evaporate during drying - regulated for health/environmental reasons

High-solid paints advantage:

  1. Higher VOC
  2. More solvent
  3. Lower VOC content
  4. Slower drying
Show the answer

Answer: C. Lower VOC content Lower VOC content (>65% solids by volume)

Powder coating applied by:

  1. Electrostatic spray then cured in oven at 180-200°C
  2. Brush
  3. Roller
  4. Dip coating
Show the answer

Answer: A. Electrostatic spray then cured in oven at 180-200°C Electrostatic spray then cured in oven at 180-200°C - zero VOC

Intumescent paint:

  1. None
  2. Decorative only
  3. Swells on fire exposure to form insulating char layer
  4. Anti-corrosion only
Show the answer

Answer: C. Swells on fire exposure to form insulating char layer Swells on fire exposure to form insulating char layer - passive fire protection

Gloss level measured by:

  1. Eye only
  2. Colour spectrophotometer
  3. Gloss meter at 60° angle or 85° / 20° reflectance
  4. None
Show the answer

Answer: C. Gloss meter at 60° angle or 85° / 20° reflectance Gloss meter at 60° angle (semi-gloss) or 85°(matte) / 20°(high gloss) reflectance

Scrub resistance test measures:

  1. None
  2. Number of scrubbing cycles before paint film fails
  3. Adhesion
  4. Flexibility
Show the answer

Answer: B. Number of scrubbing cycles before paint film fails Number of scrubbing cycles before paint film fails - indicates durability

Salt spray (ASTM B117) test measures:

  1. Corrosion resistance of paint system under salt fog exposure
  2. None
  3. Adhesion
  4. VOC content
Show the answer

Answer: A. Corrosion resistance of paint system under salt fog exposure

Pull-off adhesion test (ASTM D4541):

  1. None
  2. Hardness
  3. Measures tensile force to pull dolly off coated surface
  4. Flexibility
Show the answer

Answer: C. Measures tensile force to pull dolly off coated surface Measures tensile force to pull dolly off coated surface - quantifies adhesion

Pendulum hardness test (König/Persoz):

  1. Gloss
  2. Oscillation decay of pendulum on coated surface
  3. Impact resistance
  4. None
Show the answer

Answer: B. Oscillation decay of pendulum on coated surface Oscillation decay of pendulum on coated surface - indicates hardness

Cross-cut adhesion test (ASTM D3359):

  1. Hardness
  2. None
  3. Flexibility
  4. Grid cut through coating assessed for adhesion by tape pull
Show the answer

Answer: D. Grid cut through coating assessed for adhesion by tape pull

Sag resistance:

  1. None
  2. Gloss property
  3. Ability to apply thick coat without running/sagging
  4. Colour stability
Show the answer

Answer: C. Ability to apply thick coat without running/sagging Ability to apply thick coat without running/sagging - controlled by rheology modifiers

Flash rust on steel:

  1. Long-term corrosion
  2. None
  3. Rapid surface rust before paint dries
  4. Paint peeling
Show the answer

Answer: C. Rapid surface rust before paint dries Rapid surface rust before paint dries - prevented by flash rust inhibitors

Micaceous iron oxide (MIO) pigment:

  1. Laminar platelets that provide barrier and improve durability in industrial coatings
  2. Colour pigment only
  3. Anti-corrosion sacrificial
  4. None
Show the answer

Answer: A. Laminar platelets that provide barrier and improve durability in industrial coatings

Aluminum flake pigment provides:

  1. Only UV block
  2. Only colour
  3. None
  4. Metallic appearance and barrier effect
Show the answer

Answer: D. Metallic appearance and barrier effect Metallic appearance and barrier effect (moisture and UV)

Wash primer (etch primer):

  1. Topcoat
  2. Filler coat
  3. Thin adhesion promoter containing PVB resin + zinc chromate + phosphoric acid for metal
  4. None
Show the answer

Answer: C. Thin adhesion promoter containing PVB resin + zinc chromate + phosphoric acid for metal

Filler coat (high-build coat):

  1. Topcoat
  2. None
  3. Thick coat to fill surface irregularities before topcoat
  4. Primer
Show the answer

Answer: C. Thick coat to fill surface irregularities before topcoat Thick coat (100-200 µm) to fill surface irregularities before topcoat

DFT (Dry Film Thickness):

  1. Thickness of paint after solvent has evaporated
  2. Wet thickness
  3. Viscosity
  4. None
Show the answer

Answer: A. Thickness of paint after solvent has evaporated Thickness of paint after solvent has evaporated - measured with magnetic gauge

WFT (Wet Film Thickness) relates to DFT by:

  1. None
  2. DFT = WFT only
  3. DFT = WFT ×
  4. DFT = WFT × density
Show the answer

Answer: C. DFT = WFT × DFT = WFT × (volume solids %)

Cellulosic thickeners (e.g. HEC, HPMC) in waterborne paints:

  1. Only in solventborne
  2. Provide viscosity and sag resistance; improve open time
  3. None
  4. Pigment dispersants
Show the answer

Answer: B. Provide viscosity and sag resistance; improve open time

Biocides in water-based paint:

  1. None
  2. Driers
  3. Prevent microbial growth in can and on dry film
  4. Pigment stabilisers
Show the answer

Answer: C. Prevent microbial growth in can and on dry film Prevent microbial growth in can (in-can) and on dry film (dry film preservatives)

Driers (siccatives) in oil-based paints:

  1. None
  2. Metal salts that catalyse oxidative drying of oils
  3. Slow drying
  4. Solvents
Show the answer

Answer: B. Metal salts that catalyse oxidative drying of oils Metal salts (Co, Mn, Zr, Ca naphthenates) that catalyse oxidative drying of oils

Wetting agents in paint:

  1. Reduce surface tension to improve substrate wetting and pigment dispersion
  2. Driers
  3. None
  4. Thickeners
Show the answer

Answer: A. Reduce surface tension to improve substrate wetting and pigment dispersion

Defoamers in paint:

  1. Thickeners
  2. None
  3. Wetting agents
  4. Break down foam during manufacture and application
Show the answer

Answer: D. Break down foam during manufacture and application

UV absorbers in exterior paint:

  1. React with pigment
  2. None
  3. Absorb UV radiation to protect binder from photodegradation
  4. Reflect UV
Show the answer

Answer: C. Absorb UV radiation to protect binder from photodegradation

HALS (Hindered Amine Light Stabilisers):

  1. Scavenge free radicals formed by UV degradation
  2. UV absorbers
  3. None
  4. Driers
Show the answer

Answer: A. Scavenge free radicals formed by UV degradation Scavenge free radicals formed by UV degradation - synergistic with UV absorbers

Chalking of exterior paint:

  1. Surface powdering due to binder photodegradation
  2. None
  3. Sagging
  4. Delamination
Show the answer

Answer: A. Surface powdering due to binder photodegradation Surface powdering due to binder photodegradation - pigment exposed

Checking and cracking of paint film:

  1. None
  2. Loss of flexibility due to aging, thermal cycling
  3. Corrosion
  4. Adhesion loss
Show the answer

Answer: B. Loss of flexibility due to aging, thermal cycling Loss of flexibility due to aging, thermal cycling - indicates film brittleness

Blistering of paint:

  1. None
  2. Bubbles due to moisture or solvent vapour beneath film
  3. Chalking
  4. Cracking
Show the answer

Answer: B. Bubbles due to moisture or solvent vapour beneath film Bubbles due to moisture or solvent vapour beneath film - adhesion/osmosis related

ASTM D523 measures:

  1. Flexibility
  2. VOC
  3. Adhesion
  4. Specular gloss of paint coatings
Show the answer

Answer: D. Specular gloss of paint coatings

The critical pigment volume concentration (CPVC):

  1. PVC above which there is insufficient binder to fill pigment/filler voids
  2. Always 50%
  3. No practical meaning
  4. None
Show the answer

Answer: A. PVC above which there is insufficient binder to fill pigment/filler voids PVC above which there is insufficient binder to fill pigment/filler voids - properties change sharply

PVC (Pigment Volume Concentration):

  1. Volume of pigment / × 100%
  2. Weight ratio
  3. None
  4. Mass fraction
Show the answer

Answer: A. Volume of pigment / × 100% Volume of pigment / (volume of pigment + volume of binder) × 100%

Two-pack (2K) paint system:

  1. Two separate components mixed just before application
  2. One-pack
  3. Only powder coat
  4. None
Show the answer

Answer: A. Two separate components mixed just before application Two separate components mixed just before application (e.g. epoxy + hardener)

Moisture-cure polyurethane:

  1. UV-cure
  2. 2K system
  3. None
  4. One-pack system that cures by reaction with atmospheric moisture
Show the answer

Answer: D. One-pack system that cures by reaction with atmospheric moisture

UV-curable coatings:

  1. Cured by UV light in seconds
  2. Air dry only
  3. Heat cure only
  4. None
Show the answer

Answer: A. Cured by UV light in seconds Cured by UV light in seconds - low VOC, used in wood, electronics, printing

Waterborne coatings use water as:

  1. None
  2. Binder
  3. Pigment
  4. Carrier/diluent instead of organic solvents
Show the answer

Answer: D. Carrier/diluent instead of organic solvents Carrier/diluent instead of organic solvents - lower VOC, lower flammability

Latex paint binders:

  1. Solvent-based alkyds
  2. None
  3. Polymer emulsions in water
  4. Oil-based
Show the answer

Answer: C. Polymer emulsions in water Polymer emulsions (acrylic, vinyl acetate, styrene-acrylic) in water - coalescence drying

Coal tar epoxy coating:

  1. Uses coal tar as extender for epoxy
  2. General purpose
  3. Interior decorative
  4. None
Show the answer

Answer: A. Uses coal tar as extender for epoxy Uses coal tar as extender for epoxy - excellent immersion resistance for water, sewage

Antifouling marine paint:

  1. Anti-corrosion only
  2. Only barrier protection
  3. None
  4. Contains biocides that leach to prevent barnacle/algae growth on ship hulls
Show the answer

Answer: D. Contains biocides that leach to prevent barnacle/algae growth on ship hulls Contains biocides (Cu₂O) that leach to prevent barnacle/algae growth on ship hulls

Ablative antifouling:

  1. Self-polishing only
  2. Gradually erodes releasing biocide at controlled rate
  3. None
  4. Hard antifouling
Show the answer

Answer: B. Gradually erodes releasing biocide at controlled rate

Cathodic disbondment of pipeline coating:

  1. Anodic reaction
  2. None
  3. UV degradation
  4. Coating detaches from substrate due to cathodic protection current
Show the answer

Answer: D. Coating detaches from substrate due to cathodic protection current Coating detaches from substrate due to cathodic protection current - overprotection issue

Latex (emulsion) paint drying mechanism:

  1. Chemical crosslink
  2. Oxidative cure
  3. Water evaporates first; then polymer particles coalesce to form film
  4. None
Show the answer

Answer: C. Water evaporates first; then polymer particles coalesce to form film Water evaporates first; then polymer particles coalesce to form film (no chemical reaction)

Two-pack (2K) paint pot life:

  1. 24 hours always
  2. None
  3. Time before mixed paint gels and becomes unusable
  4. No pot life limit
Show the answer

Answer: C. Time before mixed paint gels and becomes unusable Time before mixed paint gels and becomes unusable - typically 4-8 hours

Paint sheen levels in order of gloss:

  1. Flat/Matte < Eggshell < Satin < Semi-gloss < Gloss
  2. None
  3. Flat is glossiest
  4. Random order
Show the answer

Answer: A. Flat/Matte < Eggshell < Satin < Semi-gloss < Gloss Flat/Matte < Eggshell < Satin < Semi-gloss < Gloss - measured by 60° gloss angle

Titanium dioxide particle size for hiding power:

  1. ~0.2-0.3 µm
  2. 1 µm
  3. None
  4. 0.01 µm
Show the answer

Answer: A. ~0.2-0.3 µm ~0.2-0.3 µm - size that maximises light scattering (Mie theory) for wavelengths of visible light

Rutile vs Anatase TiO₂:

  1. None
  2. Anatase for paints
  3. Both same
  4. Rutile
Show the answer

Answer: D. Rutile Rutile: higher refractive index (~2.7), better hiding power, more durable - preferred for paints; Anatase: photocatalytic

Zinc oxide in paint:

  1. None
  2. Same as TiO₂
  3. UV absorber, mildew resistance, extends life of alkyd films; less hiding power than TiO₂
  4. Only for corrosion protection
Show the answer

Answer: C. UV absorber, mildew resistance, extends life of alkyd films; less hiding power than TiO₂

Iron oxide pigments:

  1. Only red available
  2. Natural and synthetic
  3. None
  4. Poor lightfastness
Show the answer

Answer: B. Natural and synthetic Natural and synthetic - red (Fe₂O₃), yellow (FeOOH), black (Fe₃O₄) - excellent lightfastness, heat resistance

Organic pigments in paint:

  1. Phthalocyanine blue/green, azo yellows/reds, quinacridone
  2. None
  3. No organic pigments
  4. Inorganic only
Show the answer

Answer: A. Phthalocyanine blue/green, azo yellows/reds, quinacridone Phthalocyanine blue/green, azo yellows/reds, quinacridone - bright colours, high tint strength

Infrared (IR) reflective pigments:

  1. No special pigments
  2. None
  3. Reflect NIR radiation keeping surfaces cooler
  4. Absorb IR
Show the answer

Answer: C. Reflect NIR radiation keeping surfaces cooler Reflect NIR radiation keeping surfaces cooler - used in cool roof coatings and military camouflage

Phosphorescent (glow-in-dark) pigments:

  1. Radioactive
  2. Strontium aluminate
  3. None
  4. Fluorescent
Show the answer

Answer: B. Strontium aluminate Strontium aluminate - absorbs light energy, releases slowly in dark - safety markings, toys

Weather resistance testing QUV:

  1. Salt spray
  2. Heat aging
  3. Fluorescent UV lamp + condensation cycles
  4. None
Show the answer

Answer: C. Fluorescent UV lamp + condensation cycles Fluorescent UV lamp (UV-A 340nm) + condensation cycles - accelerated weathering test

Xenon arc weatherometer:

  1. None
  2. UV lamp only
  3. Simulates full sunlight spectrum + moisture
  4. Salt spray
Show the answer

Answer: C. Simulates full sunlight spectrum + moisture Simulates full sunlight spectrum (UV+visible) + moisture - most realistic outdoor simulation

ASTM D4541 test:

  1. Pull-off adhesion test
  2. Gloss test
  3. Viscosity test
  4. None
Show the answer

Answer: A. Pull-off adhesion test Pull-off adhesion test - measures tensile adhesion strength of coating to substrate

Cross-cut adhesion ISO 2409:

  1. Grid cuts + tape pull
  2. Scratch test
  3. None
  4. Pull-off test
Show the answer

Answer: A. Grid cuts + tape pull Grid cuts + tape pull - classification 0 (best) to 5 (worst) for adhesion

Scratch resistance of paint:

  1. None
  2. Gloss only
  3. Viscosity only
  4. Pencil hardness test
Show the answer

Answer: D. Pencil hardness test Pencil hardness test (ASTM D3363) - H to 9H scale; also nano-indentation for harder coatings

Bend test for paint flexibility:

  1. Pull-off test
  2. None
  3. Gloss test
  4. Mandrel bend test
Show the answer

Answer: D. Mandrel bend test Mandrel bend test - evaluates film cracking on curved surface - important for coil coatings

Impact resistance test for paint:

  1. Gloss test
  2. None
  3. Direct/reverse impact using drop weight
  4. Adhesion test
Show the answer

Answer: C. Direct/reverse impact using drop weight Direct/reverse impact using drop weight (ASTM D2794) - measures deformation without cracking

TABER abrasion test for paint:

  1. None
  2. Hardness test
  3. Salt spray
  4. Abrading wheel under set load for set cycles
Show the answer

Answer: D. Abrading wheel under set load for set cycles Abrading wheel under set load for set cycles - measures wear resistance

Mud crack defect in paint film:

  1. Thick application of high-PVC coating
  2. None
  3. Thin film defect
  4. Only in epoxy
Show the answer

Answer: A. Thick application of high-PVC coating Thick application of high-PVC coating - excessive shrinkage on drying causes mud crack pattern

Bleeding defect in paint:

  1. Sagging
  2. Adhesion failure
  3. None
  4. Soluble colourant in underlying coat migrates into new coat
Show the answer

Answer: D. Soluble colourant in underlying coat migrates into new coat Soluble colourant in underlying coat migrates into new coat - stained or discoloured finish

Pinholing in paint film:

  1. Small holes in film from air/solvent trapped
  2. Cratering
  3. Sagging
  4. None
Show the answer

Answer: A. Small holes in film from air/solvent trapped Small holes in film from air/solvent trapped - caused by fast solvent release or application on hot surface

Orange peel texture:

  1. None
  2. Sagging
  3. Mud cracking
  4. Bumpy texture like orange skin
Show the answer

Answer: D. Bumpy texture like orange skin Bumpy texture like orange skin - too-fast solvent evaporation or wrong spray technique

Dry spray (powder effect):

  1. Normal texture
  2. Sagging
  3. Spray dries before reaching substrate
  4. None
Show the answer

Answer: C. Spray dries before reaching substrate Spray dries before reaching substrate - too fast evaporating solvents or too long spray distance

Intumescent fire protection mechanism:

  1. None
  2. CO₂ release
  3. Chemical suppression
  4. Binder decomposes; carbon char swells to 50-100× original thickness; insulates steel for 30-120 min
Show the answer

Answer: D. Binder decomposes; carbon char swells to 50-100× original thickness; insulates steel for 30-120 min

Solvent-free epoxy coatings:

  1. High VOC
  2. 100% solids
  3. None
  4. Thin films
Show the answer

Answer: B. 100% solids 100% solids - very thick films (0.5-1 mm); used for tank linings, floor coatings; zero VOC

GRP (Glass Reinforced Plastic) lining:

  1. Steel lining
  2. None
  3. Fibreglass + epoxy/polyester resin
  4. Rubber lining
Show the answer

Answer: C. Fibreglass + epoxy/polyester resin Fibreglass + epoxy/polyester resin - highly chemical resistant tank lining for aggressive chemicals

Thermal spray (metallic) coatings:

  1. Thin paint only
  2. Organic only
  3. None
  4. Zinc or aluminium sprayed onto steel
Show the answer

Answer: D. Zinc or aluminium sprayed onto steel Zinc or aluminium sprayed onto steel - metallurgically bonded; used for long-life corrosion protection (50+ years)

Galvanising vs zinc-rich paint:

  1. None
  2. Galvanising
  3. Same protection
  4. ZRP superior
Show the answer

Answer: B. Galvanising Galvanising: zinc metallurgically bonded (longer life); ZRP: organic or inorganic binder with zinc dust

India's paint market size:

  1. $50 billion
  2. ~$10 billion and growing ~10-12% pa; Asian Paints, Berger, Kansai Nerolac, Akzo Nobel leading
  3. None
  4. $1 billion
Show the answer

Answer: B. ~$10 billion and growing ~10-12% pa; Asian Paints, Berger, Kansai Nerolac, Akzo Nobel leading ~$10 billion (₹80,000 crore) and growing ~10-12% pa; Asian Paints, Berger, Kansai Nerolac, Akzo Nobel leading

UV-curable coatings:

  1. None
  2. Air dry only
  3. Photoinitiator + acrylate resin cured instantly by UV light
  4. Heat cure only
Show the answer

Answer: C. Photoinitiator + acrylate resin cured instantly by UV light Photoinitiator + acrylate resin cured instantly by UV light - zero VOC, fast production line

Corrosion protection mechanisms:

  1. a
  2. B
  3. "
  4. [
Show the answer

Answer: D. [

Solvent evaporation rate in paint:

  1. v
  2. [
  3. "
  4. E
Show the answer

Answer: B. [

Kauri-butanol (KB) value:

  1. e
  2. "
  3. M
  4. [
Show the answer

Answer: D. [

Hildebrand solubility parameter:

  1. r
  2. P
  3. [
  4. "
Show the answer

Answer: C. [

Thixotropic paint:

  1. "
  2. e
  3. G
  4. [
Show the answer

Answer: D. [

Dilatant (shear-thickening) fluid:

  1. "
  2. [
  3. i
  4. V
Show the answer

Answer: B. [

HAPS (Hazardous Air Pollutants):

  1. "
  2. x
  3. [
  4. E
Show the answer

Answer: C. [

Biocidal Products Regulation (BPR) EU:

  1. C
  2. o
  3. "
  4. [
Show the answer

Answer: D. [

Direct-to-metal (DTM) coatings:

  1. S
  2. i
  3. "
  4. [
Show the answer

Answer: D. [

Concrete floor coating types:

  1. p
  2. E
  3. [
  4. "
Show the answer

Answer: C. [

Pot life vs shelf life of paint:

  1. Same concept
  2. None
  3. Pot life
  4. Only shelf life matters
Show the answer

Answer: C. Pot life Pot life: time after mixing (2K) before gel; Shelf life: storage time before application - both important

Spreading rate of paint:

  1. Not calculable
  2. m²/L at given dry film thickness
  3. None
  4. Fixed value
Show the answer

Answer: B. m²/L at given dry film thickness m²/L at given dry film thickness (DFT) - theoretical: 1000/DFT(µm) L/m² gives spreading rate

Design pressure is:

  1. Operating pressure only
  2. None
  3. Test pressure
  4. Maximum allowable working pressure + safety margin
Show the answer

Answer: D. Maximum allowable working pressure + safety margin Maximum allowable working pressure (MAWP) + safety margin (typically 10% above operating)

Hydrostatic test pressure for pressure vessels:

  1. 1.3 × MAWP
  2. 1.5 × MAWP
  3. Equal to MAWP
  4. 2 × MAWP
Show the answer

Answer: A. 1.3 × MAWP 1.3 × MAWP (ASME VIII Div 1)

Corrosion allowance in vessel design:

  1. Extra thickness added to compensate for expected corrosion over design life
  2. Design pressure margin
  3. None
  4. Safety factor
Show the answer

Answer: A. Extra thickness added to compensate for expected corrosion over design life Extra thickness added to compensate for expected corrosion over design life (typically 1-3 mm)

Joint efficiency (E) in vessel design:

  1. Always 1.0
  2. None
  3. Factor based on radiographic examination of welds
  4. 0.6 always
Show the answer

Answer: C. Factor based on radiographic examination of welds Factor based on radiographic examination of welds: 1.0 for 100% RT, 0.85 for spot RT

Ellipsoidal (2:1 semi-ellipsoidal) head:

  1. Flat head
  2. Hemispherical head
  3. Conical head
  4. Most common closed end for pressure vessels; depth = D/4
Show the answer

Answer: D. Most common closed end for pressure vessels; depth = D/4

Nozzle reinforcement:

  1. None
  2. Area of metal removed by nozzle cutout must be compensated by reinforcement pad
  3. Only for large nozzles
  4. Never required
Show the answer

Answer: B. Area of metal removed by nozzle cutout must be compensated by reinforcement pad

Reflux ratio (L/D) effect:

  1. No effect on stages
  2. None
  3. Higher reflux
  4. More reflux = more plates needed
Show the answer

Answer: C. Higher reflux Higher reflux: better separation, more stages needed; fewer stages but more energy

Minimum reflux ratio (Rmin):

  1. Maximum reflux
  2. None
  3. Zero reflux
  4. At minimum reflux, infinite stages required; determined by pinch point on McCabe-Thiele
Show the answer

Answer: D. At minimum reflux, infinite stages required; determined by pinch point on McCabe-Thiele

Reboiler duty increases with:

  1. Lower reflux
  2. None
  3. Higher reflux ratio and higher purity requirement
  4. Lower purity
Show the answer

Answer: C. Higher reflux ratio and higher purity requirement

Fired heater (furnace) design:

  1. Only radiation
  2. Radiation section, convection section, efficiency ~85-92%
  3. Only convection
  4. None
Show the answer

Answer: B. Radiation section, convection section, efficiency ~85-92% Radiation section (direct flame), convection section (flue gas), efficiency ~85-92%

Process heater duty Q =

  1. Q = F·ΔT
  2. None
  3. Q = U·A·ΔT only
  4. Q = m·Cp·ΔT + latent heat if phase change occurs
Show the answer

Answer: D. Q = m·Cp·ΔT + latent heat if phase change occurs

Reactor design - CSTR space time:

  1. τ = V·rA
  2. None
  3. Same as PFR
  4. τ = V/Q₀ =/ at exit conditions
Show the answer

Answer: D. τ = V/Q₀ =/ at exit conditions τ = V/Q₀ = (Ca0 − Ca)/(−rA) at exit conditions

Reactor design - PFR space time:

  1. None
  2. Same as CSTR
  3. τ = Ca0∫[dXA/] from 0 to XA
  4. τ =/rA
Show the answer

Answer: C. τ = Ca0∫[dXA/] from 0 to XA τ = Ca0∫[dXA/(−rA)] from 0 to XA (integral of 1/rate)

Safety relief valve sizing:

  1. Only for pressure only
  2. None
  3. Based on maximum relieving rate and back-pressure
  4. Fixed size always
Show the answer

Answer: C. Based on maximum relieving rate and back-pressure Based on maximum relieving rate (fire case, blocked outlet, etc.) and back-pressure

API 520/521 covers:

  1. None
  2. Vessel design
  3. Piping design
  4. Sizing, selection, and installation of pressure-relieving devices
Show the answer

Answer: D. Sizing, selection, and installation of pressure-relieving devices

Pipe wall thickness by ASME B31.3:

  1. TEMA code
  2. Only for pressure vessels
  3. t = PD/(2) + corrosion allowance
  4. None
Show the answer

Answer: C. t = PD/(2) + corrosion allowance t = PD/(2(SE + PY)) + corrosion allowance - process piping code

Stress intensification factor (SIF):

  1. Safety factor only
  2. Only for straight pipe
  3. None
  4. Factor applied at pipe fittings where stress is higher than in straight pipe
Show the answer

Answer: D. Factor applied at pipe fittings where stress is higher than in straight pipe Factor applied at pipe fittings (elbows, tees) where stress is higher than in straight pipe

Pump NPSH (Net Positive Suction Head):

  1. None
  2. Only velocity head
  3. NPSHa must exceed NPSHr to prevent cavitation
  4. Only discharge head
Show the answer

Answer: C. NPSHa must exceed NPSHr to prevent cavitation NPSHa (available) must exceed NPSHr (required) to prevent cavitation

Centrifugal pump affinity laws:

  1. Q∝N², H∝N
  2. None
  3. Q∝N, H∝N², P∝N³
  4. Q=constant
Show the answer

Answer: C. Q∝N, H∝N², P∝N³ Q∝N, H∝N², P∝N³ (flow, head, power vary with speed)

Compressor isentropic efficiency:

  1. Ratio of isentropic work to actual work
  2. None
  3. Only for centrifugal
  4. Always 100%
Show the answer

Answer: A. Ratio of isentropic work to actual work Ratio of isentropic work to actual work - measures compressor performance

Surge in centrifugal compressor:

  1. Normal operation
  2. None
  3. High flow condition
  4. Unstable operation at low flow
Show the answer

Answer: D. Unstable operation at low flow Unstable operation at low flow - flow reversal, vibration, damage

Anti-surge control:

  1. Recycle valve opens to increase flow above surge line when flow drops
  2. Reduces flow
  3. Increases pressure
  4. None
Show the answer

Answer: A. Recycle valve opens to increase flow above surge line when flow drops

Vessel nozzle schedule:

  1. None
  2. Material spec
  3. Table listing all nozzles on vessel with size, rating, orientation, and purpose
  4. P&ID legend
Show the answer

Answer: C. Table listing all nozzles on vessel with size, rating, orientation, and purpose

Pressure vessel inspection intervals:

  1. Fixed 5 years always
  2. None
  3. No inspection needed
  4. Determined by corrosion rate and remaining life
Show the answer

Answer: D. Determined by corrosion rate and remaining life Determined by corrosion rate and remaining life (API 510 pressure vessel inspection code)

Double block and bleed (DBB):

  1. Single valve only
  2. Two isolation valves + one bleed valve to ensure positive isolation for maintenance
  3. Spectacle blind only
  4. None
Show the answer

Answer: B. Two isolation valves + one bleed valve to ensure positive isolation for maintenance

Minimum design metal temperature (MDMT):

  1. Maximum temperature
  2. Lowest temperature at which vessel can operate without risk of brittle fracture
  3. Design temperature only
  4. None
Show the answer

Answer: B. Lowest temperature at which vessel can operate without risk of brittle fracture

Charpy impact test:

  1. Tensile test
  2. Measures toughness/notch impact energy of steel at low temperature
  3. Hardness test
  4. None
Show the answer

Answer: B. Measures toughness/notch impact energy of steel at low temperature Measures toughness/notch impact energy of steel at low temperature - determines MDMT

PWHT (Post Weld Heat Treatment):

  1. Stress-relieving heat treatment after welding required above certain thickness/material
  2. Always required
  3. Never required
  4. None
Show the answer

Answer: A. Stress-relieving heat treatment after welding required above certain thickness/material

Thin wall vs thick wall vessel criterion:

  1. D/t > 10
  2. t/D > 0.1
  3. Thin wall
  4. None
Show the answer

Answer: C. Thin wall Thin wall: D/t > 20 (or t < D/10); thick wall requires Lamé equations

Fatigue analysis for vessels:

  1. Not required
  2. None
  3. Cyclic pressure/temperature service requires fatigue assessment
  4. Only for dynamic loads
Show the answer

Answer: C. Cyclic pressure/temperature service requires fatigue assessment Cyclic pressure/temperature service requires fatigue assessment (AS 1210 Div 2, ASME Div 2)

Creep allowance in vessel design:

  1. Only for welds
  2. Not relevant
  3. None
  4. At elevated T, creep becomes significant
Show the answer

Answer: D. At elevated T, creep becomes significant At elevated T (> 0.3-0.5 Tm), creep becomes significant - time-dependent deformation considered

Stress relieving (PWHT - Post Weld Heat Treatment):

  1. None
  2. Only for stainless steel
  3. Reduces residual stresses from welding
  4. Not needed
Show the answer

Answer: C. Reduces residual stresses from welding Reduces residual stresses from welding - required by code for thick/high-strength welds

Impact testing of vessel material:

  1. Not required
  2. None
  3. Charpy V-notch test required for low-temperature service to ensure adequate toughness
  4. Only at ambient T
Show the answer

Answer: C. Charpy V-notch test required for low-temperature service to ensure adequate toughness

Minimum Design Metal Temperature (MDMT):

  1. Lowest T at which vessel is designed to operate
  2. Average T
  3. Maximum T
  4. None
Show the answer

Answer: A. Lowest T at which vessel is designed to operate Lowest T at which vessel is designed to operate - below this, embrittlement risk increases

Ultrasonic Testing (UT) for welds:

  1. Visual only
  2. None
  3. Surface only
  4. Detects internal flaws using high-frequency sound
Show the answer

Answer: D. Detects internal flaws using high-frequency sound Detects internal flaws using high-frequency sound - alternative to radiography

Magnetic Particle Testing (MT):

  1. None
  2. Non-ferrous metals
  3. Subsurface only
  4. Detects surface/near-surface defects in ferromagnetic materials using magnetic field + particles
Show the answer

Answer: D. Detects surface/near-surface defects in ferromagnetic materials using magnetic field + particles

Liquid Penetrant Testing (PT):

  1. None
  2. Surface defect detection on any material
  3. Ferrous only
  4. Subsurface only
Show the answer

Answer: B. Surface defect detection on any material Surface defect detection on any material - dye penetrant highlights cracks

Acoustic Emission (AE) testing:

  1. None
  2. Detects active cracks under stress by sound emitted
  3. Visual only
  4. Static testing
Show the answer

Answer: B. Detects active cracks under stress by sound emitted Detects active cracks under stress by sound emitted - monitoring of vessels under pressure

Hardness testing of welds (PWHT check):

  1. Not required
  2. Only for stainless
  3. None
  4. Verifies post-weld heat treatment effectiveness
Show the answer

Answer: D. Verifies post-weld heat treatment effectiveness Verifies post-weld heat treatment effectiveness - hardness limits in codes (e.g. < 250 HV for sour service)

Weld hardness for sour service (NACE MR0175):

  1. None
  2. Only impact testing
  3. < 22 HRC or < 250 HV
  4. Any hardness
Show the answer

Answer: C. < 22 HRC or < 250 HV < 22 HRC or < 250 HV - prevents sulphide stress cracking in H₂S environments

Austenitic stainless steel (304/316):

  1. Magnetic
  2. Good corrosion resistance; cannot be hardened by heat treatment; susceptible to chloride SCC
  3. Hardenable
  4. None
Show the answer

Answer: B. Good corrosion resistance; cannot be hardened by heat treatment; susceptible to chloride SCC

Duplex stainless steel (2205):

  1. Only austenitic
  2. None
  3. 50% austenite + 50% ferrite; better chloride SCC resistance than austenitic; higher strength
  4. Only ferritic
Show the answer

Answer: C. 50% austenite + 50% ferrite; better chloride SCC resistance than austenitic; higher strength

HASTELLOY alloys:

  1. Stainless steel type
  2. None
  3. Nickel-based alloys for aggressive acids, oxidising and reducing environments
  4. Carbon steel type
Show the answer

Answer: C. Nickel-based alloys for aggressive acids, oxidising and reducing environments Nickel-based alloys (C-276, C-22) for aggressive acids, oxidising and reducing environments

Weld overlay (cladding) on vessel:

  1. Depositing corrosion-resistant weld metal on internal surfaces by SMAW, SAW, or GTAW
  2. Only for repairs
  3. None
  4. Only structural welds
Show the answer

Answer: A. Depositing corrosion-resistant weld metal on internal surfaces by SMAW, SAW, or GTAW

Gasket materials for flanges:

  1. Spiral wound, ring type joint, CAF (compressed asbestos fibre
  2. Rubber only
  3. None
  4. Metal only
Show the answer

Answer: A. Spiral wound, ring type joint, CAF (compressed asbestos fibre Spiral wound (SW), ring type joint (RTJ), CAF (compressed asbestos fibre - phased out), PTFE

Flange leakage - bolt load:

  1. Only gasket quality
  2. Sufficient bolt pre-load must be maintained to compress gasket and maintain seal under pressure
  3. Not important
  4. None
Show the answer

Answer: B. Sufficient bolt pre-load must be maintained to compress gasket and maintain seal under pressure

Flange facing types:

  1. Raised face, flat face, ring type joint, tongue & groove
  2. None
  3. All the same
  4. Only RF used
Show the answer

Answer: A. Raised face, flat face, ring type joint, tongue & groove Raised face (RF), flat face (FF), ring type joint (RTJ), tongue & groove - affects gasket selection

ANSI/ASME B16.5 governs:

  1. None
  2. Vessel design
  3. Pipe flanges and fittings dimensions and pressure-temperature ratings
  4. Pump design
Show the answer

Answer: C. Pipe flanges and fittings dimensions and pressure-temperature ratings Pipe flanges and fittings dimensions and pressure-temperature ratings (Class 150-2500)

Two-phase (boiling/condensing) HX design:

  1. None
  2. Single phase only
  3. No difference
  4. Requires consideration of flow regime, two-phase pressure drop, heat flux
Show the answer

Answer: D. Requires consideration of flow regime, two-phase pressure drop, heat flux Requires consideration of flow regime (bubbly, slug, annular), two-phase pressure drop, heat flux

Critical heat flux (CHF/boiling crisis):

  1. Average heat flux
  2. Minimum heat flux
  3. Maximum heat flux before film boiling onset
  4. None
Show the answer

Answer: C. Maximum heat flux before film boiling onset Maximum heat flux before film boiling onset - avoid to prevent burn-out in boilers/reboilers

Nucleate boiling preferred over film boiling:

  1. Film boiling preferred
  2. Nucleate
  3. No preference
  4. None
Show the answer

Answer: B. Nucleate Nucleate: high h, lower T_wall; film boiling: low h, very high T_wall (Leidenfrost)

Reboiler types:

  1. Kettle, thermosiphon, forced circulation, internal
  2. Only kettle
  3. None
  4. Only thermosiphon
Show the answer

Answer: A. Kettle, thermosiphon, forced circulation, internal Kettle, thermosiphon (vertical/horizontal), forced circulation, internal - different for service

Fired heater efficiency improvement:

  1. None
  2. No improvement possible
  3. Increase fuel only
  4. Air preheating using flue gas waste heat
Show the answer

Answer: D. Air preheating using flue gas waste heat Air preheating using flue gas waste heat (air preheater / economiser)

NOx reduction in fired heaters:

  1. Only SCR
  2. None
  3. No reduction possible
  4. Low-NOx burners, SCR
Show the answer

Answer: D. Low-NOx burners, SCR Low-NOx burners (staged combustion, flue gas recirculation), SCR (selective catalytic reduction)

Lifting lug design:

  1. No factor needed
  2. None
  3. Must handle dynamic factor for vessel erection/installation
  4. Only static weight
Show the answer

Answer: C. Must handle dynamic factor for vessel erection/installation Must handle dynamic factor (~2× static weight) for vessel erection/installation

Vacuum vessel design:

  1. External pressure design
  2. Same as internal
  3. Lower thickness
  4. None
Show the answer

Answer: A. External pressure design External pressure design - more critical than internal; buckling (collapse) is failure mode

External pressure design - long cylinder:

  1. No stiffening needed
  2. None
  3. Uses stiffening rings to increase critical collapse pressure
  4. Only for spheres
Show the answer

Answer: C. Uses stiffening rings to increase critical collapse pressure Uses stiffening rings to increase critical collapse pressure - ASME Section VIII rules

Minimum thickness for corrosion allowance in vessel:

  1. Typically 1.5-3 mm CA added to calculated thickness based on corrosion rate × design life
  2. 10 mm always
  3. No allowance
  4. None
Show the answer

Answer: A. Typically 1.5-3 mm CA added to calculated thickness based on corrosion rate × design life

Inspection interval for pressure vessels:

  1. Only at failure
  2. Risk-based inspection or fixed schedule
  3. No inspection needed
  4. None
Show the answer

Answer: B. Risk-based inspection or fixed schedule Risk-based inspection (RBI) or fixed schedule - API 510 for in-service inspection

API 510 governs:

  1. In-service inspection, repair, and alteration of pressure vessels
  2. Fired heaters
  3. None
  4. New vessel design
Show the answer

Answer: A. In-service inspection, repair, and alteration of pressure vessels

API 570 governs:

  1. Vessels
  2. Fired heaters
  3. In-service inspection of piping systems
  4. None
Show the answer

Answer: C. In-service inspection of piping systems

API 653 governs:

  1. Inspection, repair, alteration, and reconstruction of above ground storage tanks
  2. Pressure vessels
  3. Piping
  4. None
Show the answer

Answer: A. Inspection, repair, alteration, and reconstruction of above ground storage tanks

On-stream inspection (OSI):

  1. Shutdown required
  2. Visual only
  3. None
  4. Inspection conducted while vessel in service using UT, thermography, IRIS
Show the answer

Answer: D. Inspection conducted while vessel in service using UT, thermography, IRIS Inspection conducted while vessel in service using UT, thermography, IRIS - avoids shutdown

Thickness measurement frequency:

  1. Annual always
  2. Based on corrosion rate
  3. None
  4. Only on failure
Show the answer

Answer: B. Based on corrosion rate Based on corrosion rate - minimum 5-year interval per API 510 for low-risk equipment

Nozzle load limits on vessel:

  1. [
  2. R
  3. "
  4. W
Show the answer

Answer: A. [

Vessel support - skirt access holes:

  1. u
  2. C
  3. "
  4. [
Show the answer

Answer: D. [

Pressure vessel code - Division 2 vs Division 1:

  1. "
  2. [
  3. D
  4. i
Show the answer

Answer: B. [

Cold boxes (cryogenic vessels):

  1. I
  2. [
  3. n
  4. "
Show the answer

Answer: B. [

LNG storage tank design:

  1. D
  2. o
  3. "
  4. [
Show the answer

Answer: D. [

Vapour liquid equilibrium (VLE) data sources:

  1. [
  2. N
  3. I
  4. "
Show the answer

Answer: A. [

Relative volatility α > 1 means component A is ___ component B:

  1. Same volatility as
  2. More volatile than
  3. Immiscible with
  4. Less volatile than
Show the answer

Answer: B. More volatile than

Falling film evaporator:

  1. [
  2. i
  3. L
  4. "
Show the answer

Answer: A. [

Multiple effect evaporator:

  1. "
  2. V
  3. [
  4. a
Show the answer

Answer: C. [

Vapour recompression (MVR) in evaporation:

  1. C
  2. "
  3. [
  4. o
Show the answer

Answer: C. [

Falling film absorber design:

  1. i
  2. [
  3. "
  4. L
Show the answer

Answer: B. [

Number of theoretical stages (McCabe-Thiele):

  1. G
  2. "
  3. r
  4. [
Show the answer

Answer: D. [

Compressor intercooling:

  1. "
  2. [
  3. C
  4. o
Show the answer

Answer: B. [

Expander (turboexpander):

  1. R
  2. [
  3. "
  4. e
Show the answer

Answer: B. [

Vessel nameplate (name plate):

  1. Optional
  2. Only for large vessels
  3. Required by ASME
  4. None
Show the answer

Answer: C. Required by ASME Required by ASME - shows MAWP, design T, material, inspection stamp (UV/U/UM) and serial number

Statutory inspection by third party:

  1. None
  2. Only in USA
  3. IBR / ASME
  4. No third party needed
Show the answer

Answer: C. IBR / ASME IBR (Indian Boiler Regulations) / ASME - independent inspection agency certifies vessels for safety

HAZOP (Hazard and Operability Study):

  1. Systematic technique using guide words to identify hazards in process P&IDs
  2. Risk quantification
  3. None
  4. QRA only
Show the answer

Answer: A. Systematic technique using guide words to identify hazards in process P&IDs

HAZOP guide words include:

  1. Only No
  2. Only More/Less
  3. No/Not, More, Less, As Well As, Part Of, Reverse, Other Than
  4. None
Show the answer

Answer: C. No/Not, More, Less, As Well As, Part Of, Reverse, Other Than

HAZAN (Hazard Analysis):

  1. Only qualitative
  2. Same as HAZOP
  3. None
  4. Quantitative risk assessment following HAZOP
Show the answer

Answer: D. Quantitative risk assessment following HAZOP Quantitative risk assessment (frequency × consequence) following HAZOP

FMEA (Failure Mode and Effects Analysis):

  1. HAZOP variant
  2. Systematic review of each failure mode and its effect on the system
  3. Only consequence analysis
  4. None
Show the answer

Answer: B. Systematic review of each failure mode and its effect on the system

FTA (Fault Tree Analysis):

  1. None
  2. HAZOP
  3. Event tree
  4. Top-down deductive method using AND/OR gates to find causes of top event
Show the answer

Answer: D. Top-down deductive method using AND/OR gates to find causes of top event

ETA (Event Tree Analysis):

  1. HAZOP
  2. Bottom-up method tracing consequences of initiating event through barriers
  3. FTA
  4. None
Show the answer

Answer: B. Bottom-up method tracing consequences of initiating event through barriers

Bow-tie diagram combines:

  1. Only FTA
  2. Only ETA
  3. None
  4. FTA (left
Show the answer

Answer: D. FTA (left FTA (left - causes) and ETA (right - consequences) with event in centre

SIL (Safety Integrity Level):

  1. None
  2. SIL 1-4
  3. Only for relief valves
  4. Only for alarms
Show the answer

Answer: B. SIL 1-4 SIL 1-4 - higher SIL means lower probability of failure on demand (PFD) for SIS

ALARP (As Low As Reasonably Practicable):

  1. Maximum risk allowed
  2. Zero risk always
  3. None
  4. Risk should be reduced until further reduction costs grossly disproportionate to benefit
Show the answer

Answer: D. Risk should be reduced until further reduction costs grossly disproportionate to benefit

Flash point of a liquid:

  1. Vapour pressure
  2. Temperature at which vapours ignite momentarily with ignition source
  3. Boiling point
  4. Auto-ignition temperature
Show the answer

Answer: B. Temperature at which vapours ignite momentarily with ignition source

Auto-ignition temperature (AIT):

  1. Temperature at which substance ignites without external ignition source
  2. Melting point
  3. Boiling point
  4. Flash point
Show the answer

Answer: A. Temperature at which substance ignites without external ignition source

LEL (Lower Explosive Limit):

  1. Maximum concentration
  2. Minimum concentration of fuel in air that can propagate flame
  3. None
  4. Stoichiometric concentration
Show the answer

Answer: B. Minimum concentration of fuel in air that can propagate flame

UEL (Upper Explosive Limit):

  1. Stoichiometric
  2. Minimum concentration
  3. Maximum concentration of fuel in air that can propagate flame
  4. None
Show the answer

Answer: C. Maximum concentration of fuel in air that can propagate flame Maximum concentration of fuel in air that can propagate flame (above this too rich)

Explosion proof equipment used in:

  1. Normal areas
  2. Hazardous areas to prevent ignition of flammable atmosphere
  3. Cold areas
  4. None
Show the answer

Answer: B. Hazardous areas to prevent ignition of flammable atmosphere Hazardous areas (Zone 0, 1, 2) to prevent ignition of flammable atmosphere

Zone 0 (IEC 60079):

  1. Occasionally present
  2. Not present normally
  3. Flammable atmosphere continuously present
  4. None
Show the answer

Answer: C. Flammable atmosphere continuously present

Zone 1:

  1. Flammable atmosphere likely during normal operation
  2. Only during abnormal
  3. Continuously present
  4. None
Show the answer

Answer: A. Flammable atmosphere likely during normal operation

Zone 2:

  1. Always present
  2. Continuously present
  3. Flammable atmosphere present only in abnormal conditions
  4. None
Show the answer

Answer: C. Flammable atmosphere present only in abnormal conditions

Bhopal disaster (1984) caused by:

  1. Chlorine leak
  2. Methyl isocyanate leak from Union Carbide pesticide plant
  3. NH₃ leak
  4. H₂S leak
Show the answer

Answer: B. Methyl isocyanate leak from Union Carbide pesticide plant Methyl isocyanate (MIC) leak from Union Carbide pesticide plant - worst industrial accident

Flixborough disaster (1974):

  1. Cyclohexane vapour cloud explosion from bypass pipe failure; 28 deaths
  2. Nuclear accident
  3. None
  4. Bhopal type
Show the answer

Answer: A. Cyclohexane vapour cloud explosion from bypass pipe failure; 28 deaths Cyclohexane vapour cloud explosion from bypass pipe failure; 28 deaths (UK)

Texas City Refinery explosion (2005):

  1. Fire only
  2. Raffinate splitter overflow → vapour cloud → explosion; 15 deaths
  3. None
  4. Pipeline explosion
Show the answer

Answer: B. Raffinate splitter overflow → vapour cloud → explosion; 15 deaths Raffinate splitter overflow → vapour cloud → explosion; 15 deaths (BP refinery)

PPE (Personal Protective Equipment) types:

  1. Only gloves
  2. Only hard hat
  3. None
  4. Hard hat, safety glasses, hearing protection, gloves, safety shoes, respirator, chemical suit
Show the answer

Answer: D. Hard hat, safety glasses, hearing protection, gloves, safety shoes, respirator, chemical suit

Permit to Work (PTW) system:

  1. For routine work
  2. None
  3. Formal system authorising hazardous work
  4. Optional procedure
Show the answer

Answer: C. Formal system authorising hazardous work Formal system authorising hazardous work (hot work, confined space, electrical isolation)

Hot work permit required for:

  1. Any work involving flames or sparks in hazardous area
  2. Routine inspection
  3. None
  4. All office work
Show the answer

Answer: A. Any work involving flames or sparks in hazardous area Any work involving flames or sparks (welding, grinding, cutting) in hazardous area

Confined space entry requires:

  1. No special precautions
  2. Only ventilation
  3. None
  4. Permit, atmospheric testing, ventilation, attendant, rescue plan, LOTO
Show the answer

Answer: D. Permit, atmospheric testing, ventilation, attendant, rescue plan, LOTO

LOTO (Lockout-Tagout):

  1. Only valve isolation
  2. None
  3. Only electrical isolation
  4. Isolation of energy sources before maintenance
Show the answer

Answer: D. Isolation of energy sources before maintenance Isolation of energy sources (electrical, pneumatic, hydraulic) before maintenance

Safety shower and eyewash:

  1. Required near areas with corrosive chemicals; drench with water for 15 minutes
  2. None
  3. Only eyewash needed
  4. Only shower needed
Show the answer

Answer: A. Required near areas with corrosive chemicals; drench with water for 15 minutes

Pressure relief valve (PRV):

  1. Spring-loaded valve that opens at set pressure to protect vessel from over-pressure
  2. None
  3. Shuts at high pressure
  4. Rupture disc
Show the answer

Answer: A. Spring-loaded valve that opens at set pressure to protect vessel from over-pressure

Rupture disc:

  1. None
  2. Re-closable
  3. Thin disc that bursts at design pressure
  4. Resealing device
Show the answer

Answer: C. Thin disc that bursts at design pressure Thin disc that bursts at design pressure - one-time device; faster response than PRV

Fire triangle elements:

  1. Only fuel and O₂
  2. None
  3. Only fuel and ignition
  4. Fuel, Oxidiser, and Ignition source
Show the answer

Answer: D. Fuel, Oxidiser, and Ignition source Fuel, Oxidiser (oxygen), and Ignition source - remove any one to prevent fire

Fire tetrahedron adds:

  1. Chemical chain reaction to fire triangle
  2. None
  3. Heat
  4. Fourth element water
Show the answer

Answer: A. Chemical chain reaction to fire triangle Chemical chain reaction to fire triangle - breaking chain prevents fire

Class A fire:

  1. Electrical
  2. Ordinary combustibles
  3. Metals
  4. Flammable liquids
Show the answer

Answer: B. Ordinary combustibles Ordinary combustibles (wood, paper, fabric)

Class B fire:

  1. Flammable liquids and gases
  2. Ordinary combustibles
  3. Electrical
  4. Metal
Show the answer

Answer: A. Flammable liquids and gases Flammable liquids and gases (petrol, oil)

Class C fire:

  1. Combustibles
  2. Electrical equipment fires
  3. Flammable liquids
  4. Metal
Show the answer

Answer: B. Electrical equipment fires

Class D fire:

  1. Ordinary combustibles
  2. Combustible metals
  3. Flammable liquids
  4. Electrical
Show the answer

Answer: B. Combustible metals Combustible metals (magnesium, sodium, potassium)

Deluge system:

  1. Open sprinklers activated simultaneously by fire detection
  2. Foam system
  3. None
  4. Sprinkler
Show the answer

Answer: A. Open sprinklers activated simultaneously by fire detection Open sprinklers activated simultaneously by fire detection - flood zone with water

Halon alternatives (clean agents):

  1. FM-200, Novec 1230, CO₂
  2. None
  3. Water only
  4. Sand only
Show the answer

Answer: A. FM-200, Novec 1230, CO₂ FM-200 (HFC-227ea), Novec 1230, CO₂ - used in computer rooms, electrical cabinets

MSDS (Material Safety Data Sheet) / SDS (Safety Data Sheet):

  1. Only storage info
  2. Only toxicity info
  3. None
  4. Document providing hazard, handling, storage, and emergency info for chemicals
Show the answer

Answer: D. Document providing hazard, handling, storage, and emergency info for chemicals

GHS (Globally Harmonised System):

  1. International system for classification and labelling of chemicals with standardised pictograms
  2. US only
  3. None
  4. Indian standard only
Show the answer

Answer: A. International system for classification and labelling of chemicals with standardised pictograms

TLV-TWA (Threshold Limit Value - Time-Weighted Average):

  1. Maximum average airborne concentration for 8-hr workday exposure
  2. Any duration
  3. Peak concentration
  4. None
Show the answer

Answer: A. Maximum average airborne concentration for 8-hr workday exposure

STEL (Short-Term Exposure Limit):

  1. 8-hour limit
  2. None
  3. Maximum concentration for 15-minute exposure
  4. 1-hour limit
Show the answer

Answer: C. Maximum concentration for 15-minute exposure Maximum concentration for 15-minute exposure (not more than 4 times/day)

IDLH (Immediately Dangerous to Life or Health):

  1. Concentration posing immediate danger to life or health
  2. Safe concentration
  3. None
  4. TLV-TWA
Show the answer

Answer: A. Concentration posing immediate danger to life or health Concentration posing immediate danger to life or health - escape within 30 minutes

Risk matrix:

  1. Quantitative only
  2. Combines likelihood and consequence to rank risks (colour-coded
  3. Only consequence
  4. Only likelihood
Show the answer

Answer: B. Combines likelihood and consequence to rank risks (colour-coded Combines likelihood and consequence to rank risks (colour-coded: green/yellow/red)

Inherently Safer Design (ISD) principles:

  1. Minimise, Substitute, Moderate, Simplify
  2. None
  3. Add more controls
  4. Increase safeguards
Show the answer

Answer: A. Minimise, Substitute, Moderate, Simplify Minimise, Substitute, Moderate, Simplify - reduce hazard at source rather than add protection

Layer of Protection Analysis (LOPA):

  1. Same as FTA
  2. None
  3. Semi-quantitative method to determine if sufficient IPLs exist
  4. HAZOP variant
Show the answer

Answer: C. Semi-quantitative method to determine if sufficient IPLs exist Semi-quantitative method to determine if sufficient IPLs (independent protection layers) exist

IPL (Independent Protection Layer):

  1. None
  2. Non-independent control
  3. Device or system that prevents hazardous event independent of initiating cause
  4. Operator action only
Show the answer

Answer: C. Device or system that prevents hazardous event independent of initiating cause Device or system that prevents hazardous event independent of initiating cause (e.g. SIS, relief valve)

MOC (Management of Change):

  1. Formal process to review and approve changes to process, equipment, or procedures before implementation
  2. Post-change review only
  3. None
  4. No review needed
Show the answer

Answer: A. Formal process to review and approve changes to process, equipment, or procedures before implementation

Incident investigation tools:

  1. Root Cause Analysis, 5-Why, fishbone, bow-tie
  2. Only reporting
  3. None
  4. Only corrective action
Show the answer

Answer: A. Root Cause Analysis, 5-Why, fishbone, bow-tie Root Cause Analysis (RCA), 5-Why, fishbone (Ishikawa), bow-tie

OSHA (USA) / HSE (UK) equivalent in India:

  1. SEBI
  2. RBI
  3. CPCB
  4. Director General Factory Advice Service and Labour Institutes; State Factory Inspectorates
Show the answer

Answer: D. Director General Factory Advice Service and Labour Institutes; State Factory Inspectorates Director General Factory Advice Service and Labour Institutes (DGFASLI); State Factory Inspectorates

Factories Act India (1948) requires:

  1. Safety, health and welfare provisions for workers in factories employing 10+ workers with power
  2. Only chemical factories
  3. Only large factories
  4. None
Show the answer

Answer: A. Safety, health and welfare provisions for workers in factories employing 10+ workers with power

The Manufacture, Storage and Import of Hazardous Chemicals Rules (MSIHC) 1989:

  1. Pharmaceutical only
  2. Identifies major hazard installations; requires on-site and off-site emergency plans
  3. Fertiliser only
  4. None
Show the answer

Answer: B. Identifies major hazard installations; requires on-site and off-site emergency plans

Dispersion modelling for gas release:

  1. No modelling needed
  2. Only visual inspection
  3. None
  4. Gaussian plume model or PHAST/SAFETI software
Show the answer

Answer: D. Gaussian plume model or PHAST/SAFETI software Gaussian plume model or PHAST/SAFETI software - predicts concentration downwind

Toxic gas cloud - consequence modelling:

  1. Only colour coding
  2. IDLH, ERPG, AEGL levels used for impact zones
  3. None
  4. Only alarm setting
Show the answer

Answer: B. IDLH, ERPG, AEGL levels used for impact zones IDLH, ERPG (Emergency Response Planning Guidelines), AEGL levels used for impact zones

BLEVE (Boiling Liquid Expanding Vapour Explosion):

  1. Normal fire
  2. Gas explosion only
  3. Pressurised vessel fails
  4. None
Show the answer

Answer: C. Pressurised vessel fails Pressurised vessel fails - liquid flashes to vapour - explosive expansion + fireball (LPG tank fires)

Fireball vs UVCE vs flash fire:

  1. No difference
  2. All same
  3. None
  4. Fireball
Show the answer

Answer: D. Fireball Fireball: burning cloud rises; UVCE (unconfined vapour cloud explosion): deflagration/detonation; Flash fire: burns without explosion

Detonation vs deflagration:

  1. Detonation
  2. Deflagration faster
  3. Same
  4. None
Show the answer

Answer: A. Detonation Detonation: supersonic flame front (>Mach 1) - more destructive; Deflagration: subsonic (<Mach 1)

DDT (Deflagration-to-Detonation Transition):

  1. Flame accelerates in confined space until it transitions to detonation
  2. Never occurs
  3. Always detonation
  4. None
Show the answer

Answer: A. Flame accelerates in confined space until it transitions to detonation Flame accelerates in confined space until it transitions to detonation - critical in gas pipelines

TNT equivalency method:

  1. None
  2. Converts explosive energy of vapour cloud to equivalent TNT mass for blast damage estimation
  3. Overpressure only
  4. Thermal only
Show the answer

Answer: B. Converts explosive energy of vapour cloud to equivalent TNT mass for blast damage estimation

Probit method in QRA:

  1. Binary outcome only
  2. Converts dose to probability of injury/death
  3. None
  4. HAZOP method
Show the answer

Answer: B. Converts dose to probability of injury/death Converts dose (concentration × time) to probability of injury/death - dose-response relationship

Individual risk:

  1. Societal risk
  2. Probability per year of death for a specific person at a specific location due to hazard
  3. None
  4. Group risk
Show the answer

Answer: B. Probability per year of death for a specific person at a specific location due to hazard

Societal risk (FN curve):

  1. Location risk
  2. None
  3. Individual risk
  4. Frequency vs Number of fatalities curve
Show the answer

Answer: D. Frequency vs Number of fatalities curve Frequency vs Number of fatalities curve - shows risk to population

Risk tolerability criteria:

  1. Broadly acceptable <10⁻⁶/year; intolerable >10⁻⁴/year; ALARP in between
  2. Only 10⁻³
  3. None
  4. No criteria
Show the answer

Answer: A. Broadly acceptable <10⁻⁶/year; intolerable >10⁻⁴/year; ALARP in between

Inerting:

  1. Purging with air
  2. None
  3. Replacing air in vessel with inert gas to prevent flammable atmosphere
  4. Adding O₂
Show the answer

Answer: C. Replacing air in vessel with inert gas to prevent flammable atmosphere Replacing air in vessel with inert gas (N₂, CO₂) to prevent flammable atmosphere

Purging methods:

  1. No purging needed
  2. Pressure purge, vacuum purge, sweep purge
  3. Only one method
  4. None
Show the answer

Answer: B. Pressure purge, vacuum purge, sweep purge Pressure purge (fill/vent), vacuum purge (evacuate/fill), sweep purge (flow-through)

Static electricity control:

  1. No control needed
  2. Only ventilation
  3. None
  4. Bonding and earthing of vessels during transfer of flammable liquids
Show the answer

Answer: D. Bonding and earthing of vessels during transfer of flammable liquids Bonding and earthing (grounding) of vessels during transfer of flammable liquids

Minimum Ignition Energy (MIE):

  1. Not measurable
  2. None
  3. Minimum energy to ignite flammable mixture
  4. Same for all fuels
Show the answer

Answer: C. Minimum energy to ignite flammable mixture Minimum energy to ignite flammable mixture - hydrogen lowest (~0.017 mJ); dust explosions higher

Dust explosion pentagon:

  1. 3 factors
  2. None
  3. Fuel, Oxidiser, Ignition, Dispersion, Confinement
  4. Fire triangle only
Show the answer

Answer: C. Fuel, Oxidiser, Ignition, Dispersion, Confinement Fuel, Oxidiser, Ignition, Dispersion, Confinement - all 5 needed

Kst value for dust:

  1. Concentration only
  2. None
  3. Deflagration index
  4. Particle size only
Show the answer

Answer: C. Deflagration index Deflagration index (bar·m/s) - measures dust explosion severity (KSt 0 = no explosion; >300 = severe)

Explosion suppression systems:

  1. Passive only
  2. Only venting
  3. None
  4. Detect early pressure rise and inject suppressant to stop explosion
Show the answer

Answer: D. Detect early pressure rise and inject suppressant to stop explosion Detect early pressure rise and inject suppressant (halon alternative, NaHCO₃) to stop explosion

Explosion venting (deflagration venting):

  1. Always sufficient
  2. Only for detonation
  3. None
  4. Weak panels or rupture discs relieve pressure of dust/gas explosion to safe area
Show the answer

Answer: D. Weak panels or rupture discs relieve pressure of dust/gas explosion to safe area

Double block and bleed (DBB):

  1. Optional
  2. None
  3. Two isolation valves with bleed valve between
  4. Single valve isolation
Show the answer

Answer: C. Two isolation valves with bleed valve between Two isolation valves with bleed valve between - ensures full isolation (no leak-by) for maintenance

Blind flange vs spectacle blind:

  1. Both isolate but spectacle blind allows easy switching between isolation and flow
  2. Same as each other
  3. None
  4. Spectacle blind is permanent
Show the answer

Answer: A. Both isolate but spectacle blind allows easy switching between isolation and flow

Car seal open/car seal closed valves:

  1. Valves sealed in required position with wire seal to prevent inadvertent operation
  2. Locked valves
  3. None
  4. Normally open/closed
Show the answer

Answer: A. Valves sealed in required position with wire seal to prevent inadvertent operation

Deluge valve activation:

  1. None
  2. Sprinkler only
  3. Dry pipe with open heads; deluge valve opens on fire detection signal
  4. Wet pipe system
Show the answer

Answer: C. Dry pipe with open heads; deluge valve opens on fire detection signal Dry pipe with open heads; deluge valve opens on fire detection signal - floods entire zone

Foam fire suppression:

  1. AFFF floats on fuel surface
  2. Water only
  3. CO₂ only
  4. None
Show the answer

Answer: A. AFFF floats on fuel surface AFFF (aqueous film-forming foam) floats on fuel surface - smothers flammable liquid fires

Dry chemical powder:

  1. Interrupts chain reaction; used for Class B and C fires
  2. Water-based
  3. CO₂ type
  4. None
Show the answer

Answer: A. Interrupts chain reaction; used for Class B and C fires Interrupts chain reaction; used for Class B and C fires - residue can damage equipment

Carbon dioxide extinguishing:

  1. None
  2. Displaces O₂
  3. Flammable
  4. Leaves residue
Show the answer

Answer: B. Displaces O₂ Displaces O₂ - good for enclosed spaces, electrical fires; asphyxiation hazard to people

Clean agent (FM-200, Novec 1230):

  1. Only CO₂ type
  2. Chemical suppression without leaving residue
  3. None
  4. Water equivalent
Show the answer

Answer: B. Chemical suppression without leaving residue Chemical suppression without leaving residue - for server rooms, control rooms

MAPP gas vs acetylene in welding:

  1. Acetylene higher flame temperature but more dangerous; MAPP safer, lower T
  2. MAPP hotter
  3. None
  4. Same temperature
Show the answer

Answer: A. Acetylene higher flame temperature but more dangerous; MAPP safer, lower T Acetylene higher flame temperature (~3480°C) but more dangerous; MAPP safer, lower T

Hot-work in flammable area - gas test:

  1. None
  2. Must test LEL before and during hot work; < 10% LEL typically required
  3. Only visual check
  4. No test needed
Show the answer

Answer: B. Must test LEL before and during hot work; < 10% LEL typically required

Cold work permit:

  1. No permit needed
  2. None
  3. For non-sparking work in potentially hazardous area
  4. Only hot work permit
Show the answer

Answer: C. For non-sparking work in potentially hazardous area For non-sparking work (e.g. painting, scaffolding) in potentially hazardous area

Confined space atmospheric hazards:

  1. Only flammable gas
  2. None
  3. O₂ deficiency, O₂ excess, flammable gas, toxic gas
  4. Only O₂ checked
Show the answer

Answer: C. O₂ deficiency, O₂ excess, flammable gas, toxic gas O₂ deficiency (<19.5%), O₂ excess (>23.5%), flammable gas (>10% LEL), toxic gas

Four-gas monitor used for confined space:

  1. O₂, LEL, CO, H₂S
  2. Only O₂
  3. Only LEL
  4. None
Show the answer

Answer: A. O₂, LEL, CO, H₂S O₂, LEL (combustibles), CO, H₂S - simultaneous measurement

Hydrogen sulphide (H₂S) hazards:

  1. Light gas
  2. Mild irritant
  3. Highly toxic, flammable, heavier than air, paralyses sense of smell at high conc
  4. None
Show the answer

Answer: C. Highly toxic, flammable, heavier than air, paralyses sense of smell at high conc Highly toxic (IDLH 50 ppm), flammable, heavier than air, paralyses sense of smell at high conc

Ammonia (NH₃) hazards:

  1. None
  2. Non-toxic
  3. Non-flammable
  4. Toxic, flammable 15-28% LEL-UEL, strong odour warning at low conc
Show the answer

Answer: D. Toxic, flammable 15-28% LEL-UEL, strong odour warning at low conc Toxic (TLV 25 ppm), flammable 15-28% LEL-UEL, strong odour warning at low conc

Chlorine (Cl₂) hazards:

  1. None
  2. Flammable
  3. Toxic, heavier than air
  4. Light gas
Show the answer

Answer: C. Toxic, heavier than air Toxic (IDLH 10 ppm), heavier than air - pools in low areas, used as chemical warfare agent WWI

Phosgene (COCl₂) hazards:

  1. Flammable
  2. Extremely toxic; delayed pulmonary oedema
  3. Low toxicity
  4. None
Show the answer

Answer: B. Extremely toxic; delayed pulmonary oedema Extremely toxic (IDLH 2 ppm); delayed pulmonary oedema - may feel fine then die 12-24 hr later

HF (Hydrofluoric acid) special hazards:

  1. Penetrates skin painlessly; F⁻ depletes Ca²⁺ and Mg²⁺
  2. None
  3. No special treatment
  4. Surface burns only
Show the answer

Answer: A. Penetrates skin painlessly; F⁻ depletes Ca²⁺ and Mg²⁺ Penetrates skin painlessly; F⁻ depletes Ca²⁺ and Mg²⁺ - cardiac arrest; requires calcium gluconate antidote

Thermal radiation from fire:

  1. Increases with distance
  2. Decreases with square of distance; fireball produces intense radiation
  3. Constant with distance
  4. None
Show the answer

Answer: B. Decreases with square of distance; fireball produces intense radiation Decreases with square of distance (inverse square law); fireball produces intense radiation

Overpressure from explosion - structural damage:

  1. None
  2. All the same
  3. Only threshold
  4. Side-on peak overpressure
Show the answer

Answer: D. Side-on peak overpressure Side-on peak overpressure: ~0.3 bar shatters glass, ~0.5 bar structural damage, >1 bar severe collapse

Emergency response plan (ERP) requirements:

  1. Roles and responsibilities, communication, evacuation, shelter-in-place, muster point, drills
  2. No plan needed
  3. None
  4. Only evacuation
Show the answer

Answer: A. Roles and responsibilities, communication, evacuation, shelter-in-place, muster point, drills

Muster point:

  1. Designated safe assembly area for headcount after emergency evacuation
  2. Entry point
  3. Storage area
  4. None
Show the answer

Answer: A. Designated safe assembly area for headcount after emergency evacuation

COSHH assessment (UK) / similar process safety health:

  1. Control of Substances Hazardous to Health
  2. Only for gases
  3. Only air quality
  4. None
Show the answer

Answer: A. Control of Substances Hazardous to Health Control of Substances Hazardous to Health - risk assessment and exposure controls

Biomonitoring in occupational health:

  1. Air monitoring only
  2. None
  3. Measuring biological markers of chemical exposure
  4. No monitoring needed
Show the answer

Answer: C. Measuring biological markers of chemical exposure Measuring biological markers (urine, blood) of chemical exposure - e.g. benzene metabolites

Noise dosimetry:

  1. None
  2. No standard
  3. Instantaneous only
  4. Personal device worn by worker measures cumulative noise dose over shift
Show the answer

Answer: D. Personal device worn by worker measures cumulative noise dose over shift Personal device worn by worker measures cumulative noise dose over shift - compared to 85 dB(A) limit

Psychosocial hazards in workplace:

  1. No occupational link
  2. Stress, fatigue, shift work, harassment
  3. Physical only
  4. None
Show the answer

Answer: B. Stress, fatigue, shift work, harassment Stress, fatigue, shift work, harassment - recognised occupational health hazards

OSHA PSM (Process Safety Management, USA):

  1. None
  2. 14 elements including PHA, MOC, incident investigation, emergency planning for highly hazardous chemicals
  3. Only documentation
  4. Only 3 elements
Show the answer

Answer: B. 14 elements including PHA, MOC, incident investigation, emergency planning for highly hazardous chemicals

EU Seveso III Directive:

  1. None
  2. USA directive
  3. Only Seveso I
  4. Requires major accident prevention policies and safety reports for COMAH sites
Show the answer

Answer: D. Requires major accident prevention policies and safety reports for COMAH sites Requires major accident prevention policies and safety reports for COMAH (upper/lower tier) sites

COMAH (Control of Major Accident Hazards) in UK:

  1. Optional in UK
  2. Only for nuclear
  3. None
  4. Implements Seveso Directive; requires safety reports for upper tier sites
Show the answer

Answer: D. Implements Seveso Directive; requires safety reports for upper tier sites

Safety Case regime (UK offshore):

  1. Duty holder must demonstrate risks are reduced ALARP
  2. Only nuclear
  3. None
  4. Only onshore
Show the answer

Answer: A. Duty holder must demonstrate risks are reduced ALARP Duty holder must demonstrate risks are reduced ALARP - required for all offshore installations

IEC 61511 standard:

  1. HAZOP standard
  2. None
  3. Risk matrix only
  4. Functional safety of safety instrumented systems in process industry
Show the answer

Answer: D. Functional safety of safety instrumented systems in process industry Functional safety of safety instrumented systems (SIS) in process industry - SIL assignment

SIS lifecycle (IEC 61511):

  1. Design only
  2. Concept → design → installation → validation → operation → maintenance → modification
  3. None
  4. Operation only
Show the answer

Answer: B. Concept → design → installation → validation → operation → maintenance → modification Concept → design → installation → validation → operation → maintenance → modification - all stages

Proof test:

  1. Periodic test of SIS components to reveal undetected failures and maintain required SIL
  2. None
  3. No testing needed
  4. Only for instruments
Show the answer

Answer: A. Periodic test of SIS components to reveal undetected failures and maintain required SIL

PFD (Probability of Failure on Demand) for SIL 2:

  1. 10⁻¹
  2. 10⁻³ to 10⁻²
  3. 10⁻⁵
  4. None
Show the answer

Answer: B. 10⁻³ to 10⁻² 10⁻³ to 10⁻² (0.001-0.01) - i.e. fails in 1 in 100-1000 demands

Emergency depressurisation system:

  1. None
  2. Only for water
  3. Rapidly vents vessel contents to reduce inventory in fire case
  4. Increases pressure
Show the answer

Answer: C. Rapidly vents vessel contents to reduce inventory in fire case Rapidly vents vessel contents (liquid to flare, gas to flare) to reduce inventory in fire case

Inherently Safer Design levels:

  1. M
  2. [
  3. "
  4. i
Show the answer

Answer: B. [

Quantified Risk Assessment (QRA) steps:

  1. "
  2. a
  3. H
  4. [
Show the answer

Answer: D. [

Toxic release modelling - source models:

  1. i
  2. [
  3. L
  4. "
Show the answer

Answer: B. [

The Pasquill-Gifford stability classes range from A to:

  1. G
  2. D
  3. F
  4. H
Show the answer

Answer: C. F

Neutrally buoyant gas dispersion:

  1. "
  2. G
  3. a
  4. [
Show the answer

Answer: D. [

Dense (heavy) gas dispersion:

  1. [
  2. e
  3. H
  4. "
Show the answer

Answer: A. [

Phast/SAFETI software:

  1. "
  2. N
  3. [
  4. D
Show the answer

Answer: C. [

HAZID (Hazard Identification):

  1. [
  2. "
  3. E
  4. a
Show the answer

Answer: A. [

CHAZOP (Computer HAZOP):

  1. [
  2. "
  3. H
  4. A
Show the answer

Answer: A. [

Safety culture levels (Westrum):

  1. a
  2. P
  3. "
  4. [
Show the answer

Answer: D. [

Heinrich's Triangle ratio (major:minor:near-miss incidents) is:

  1. 1 : 29 : 300
  2. 1 : 10 : 100
  3. 1 : 5 : 50
  4. 1 : 50 : 500
Show the answer

Answer: A. 1 : 29 : 300

Swiss Cheese Model (Reason):

  1. [
  2. "
  3. M
  4. u
Show the answer

Answer: A. [

Bow-tie central event:

  1. [
  2. "
  3. T
  4. h
Show the answer

Answer: A. [

ISD - Process Intensification:

  1. "
  2. r
  3. [
  4. D
Show the answer

Answer: C. [

LOPA frequency criteria:

  1. "
  2. [
  3. I
  4. n
Show the answer

Answer: B. [

ATEX directive (EU):

  1. "
  2. [
  3. q
  4. E
Show the answer

Answer: B. [

IECEx certification:

  1. I
  2. [
  3. "
  4. n
Show the answer

Answer: B. [

Gas detection - point detector vs open path:

  1. P
  2. "
  3. o
  4. [
Show the answer

Answer: D. [

Catalytic bead (pellistor) sensor:

  1. [
  2. M
  3. e
  4. "
Show the answer

Answer: A. [

Photoionisation detector (PID):

  1. "
  2. [
  3. U
  4. V
Show the answer

Answer: B. [

Fire risk assessment:

  1. d
  2. I
  3. [
  4. "
Show the answer

Answer: C. [

Passive fire protection (PFP):

  1. "
  2. I
  3. n
  4. [
Show the answer

Answer: D. [

Active fire protection (AFP):

  1. p
  2. "
  3. [
  4. S
Show the answer

Answer: C. [

Fire and gas detection zoning:

  1. "
  2. a
  3. [
  4. E
Show the answer

Answer: C. [

Emergency shutdown (ESD) system test:

  1. "
  2. P
  3. [
  4. a
Show the answer

Answer: C. [

Two-out-of-three (2oo3) voting:

  1. S
  2. [
  3. "
  4. I
Show the answer

Answer: B. [

Pressure relief system design standard:

  1. "
  2. [
  3. P
  4. A
Show the answer

Answer: B. [

Multiple relief device sizing:

  1. [
  2. o
  3. "
  4. F
Show the answer

Answer: A. [

Flare system design:

  1. H
  2. [
  3. e
  4. "
Show the answer

Answer: B. [

Ground flare vs elevated flare:

  1. "
  2. G
  3. r
  4. [
Show the answer

Answer: D. [

SIMOPS (Simultaneous Operations):

  1. No risk in SIMOPS
  2. None
  3. Always prohibited
  4. Concurrent activities with potential interaction hazards
Show the answer

Answer: D. Concurrent activities with potential interaction hazards Concurrent activities with potential interaction hazards - requires risk assessment and controls

Hot work during SIMOPS:

  1. Special precautions
  2. Not allowed
  3. Normal hot work
  4. None
Show the answer

Answer: A. Special precautions Special precautions - additional gas monitors, standby fire watch, reduced radius - never routine

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →