IITIAN1997 STUDIO

Design of steel structures

JLEE CE · 12 practice questions with answers

Practise and take a mock test →

Connections and members to IS 800

Topics: Steel sections and properties; design considerations; riveted, bolted and welded connections; simple beam connections; tension and compression members; beams; column bases.

Steel sections and the limit state approach

IS 800:2007 uses limit state design with partial safety factors γ_m0 = 1.10 (yielding) and γ_m1 = 1.25 (ultimate). Structural steel E250 (Fe410) has f_y = 250 MPa and f_u = 410 MPa. Rolled sections: I-beams (ISMB), channels, angles, tees and tubes.

  • γ_m0 = 1.10; γ_m1 = 1.25
  • E250: f_y 250, f_u 410 MPa
  • T_dg = A_g f_y/γ_m0

Example: An angle with A_g = 1000 mm² (E250) is in tension. Find its gross-yielding strength.

  1. T_dg = 1000 × 250/1.10.
  2. ≈ 227 kN.

Answer: ≈ 227 kN

Bolted and welded connections

A bolt’s design shear strength V_dsb = f_ub/(√3 γ_mb) × n_n A_nb (γ_mb = 1.25), where A_nb is the net tensile stress area (245 mm² for M20). Bearing on the plate is also checked. Fillet welds have an effective throat of 0.7 × size; their strength per mm = f_u/(√3 γ_mw) × throat (γ_mw = 1.25 shop).

  • V_dsb = f_ub A_nb/(√3 × 1.25)
  • Throat = 0.7s
  • Check shear and bearing

Example: Find the single-shear strength of an M20 bolt of grade 4.6 (f_ub = 400 MPa, A_nb = 245 mm²).

  1. V = 400/(1.732 × 1.25) × 245.
  2. ≈ 45.3 kN.

Answer: ≈ 45 kN

Example: Find the strength per mm of a 6 mm shop fillet weld (f_u = 410 MPa).

  1. Throat = 0.7 × 6 = 4.2 mm.
  2. 410/(1.732 × 1.25) × 4.2 ≈ 795 N/mm.

Answer: ≈ 0.8 kN/mm

Tension and compression members, beams

A tension member’s strength is the least of gross yielding, net-section rupture (T_dn = 0.9 A_n f_u/γ_m1 for plates) and block shear. Compression members are designed by buckling class curves; the slenderness ratio KL/r should not exceed 180 for members carrying loads. Beams are checked for bending, shear, deflection and lateral-torsional buckling.

  • T_dn = 0.9 A_n f_u/γ_m1
  • KL/r ≤ 180 (compression)
  • Design strength = least of all checks

Example: A plate has net area 800 mm² (f_u = 410 MPa). Find its rupture strength.

  1. T_dn = 0.9 × 800 × 410/1.25.
  2. ≈ 236 kN.

Answer: ≈ 236 kN

Example: A strut 3 m long has r = 20 mm and K = 1. Is its slenderness within 180?

  1. KL/r = 3000/20 = 150.
  2. 150 < 180: acceptable.

Answer: 150, acceptable

Structural mild steel (E250) has yield stress 250 MPa and Young’s modulus 2 × 10⁵ MPa. IS 800:2007 uses limit state design with γm0 = 1.10 for yielding and γm1 = 1.25 for ultimate failure. Tension members are checked for yielding (Tdg = Ag·fy/γm0), net-section rupture and block shear. Bolts are checked for shear and bearing. A fillet weld has effective throat of about 0.7 times its size. Compression members depend on slenderness KL/r. A column base spreads the load to concrete through a slab or gusset base.

  • Minimum bolt pitch 2.5d.
  • Slenderness limits: 180 for loaded compression members; 400 for tension members.
  • High-strength friction grip bolts carry load by friction.
  • Shear lag reduces the net area efficiency of angles connected through one leg.
  • Rolled sections: ISMB (beam), ISMC (channel), ISA (angle).

Key formulas

  • Tdg = Ag·fy/γm0
  • t_e = 0.7s
  • λ = KL/r
  • Pitch ≥ 2.5d

Practice questions

Yield stress of E250 steel is

  1. 150 MPa
  2. 250 MPa
  3. 415 MPa
  4. 500 MPa
Show the answer

Answer: B. 250 MPa Grade name.

Partial safety factor for yielding, γm0, is

  1. 1.10
  2. 1.25
  3. 1.5
  4. 1.15
Show the answer

Answer: A. 1.10 IS 800.

Partial safety factor for ultimate failure, γm1, is

  1. 1.10
  2. 1.25
  3. 1.5
  4. 2.0
Show the answer

Answer: B. 1.25 IS 800.

Throat of a fillet weld with size s is

  1. 0.5s
  2. 0.7s
  3. s
  4. 1.4s
Show the answer

Answer: B. 0.7s For a 90° joint.

Minimum pitch of bolts is

  1. 1.5d
  2. 2.5d
  3. 5d
  4. 10d
Show the answer

Answer: B. 2.5d Nominal diameter d.

Young’s modulus of steel is about

  1. 2 × 10⁵ MPa
  2. 2 × 10³ MPa
  3. 2 × 10⁷ MPa
  4. 25 MPa
Show the answer

Answer: A. 2 × 10⁵ MPa 200 GPa.

An ISMB section is a

  1. rolled beam
  2. channel
  3. angle
  4. plate
Show the answer

Answer: A. rolled beam Medium-weight beam.

The main load on a column base is

  1. axial compression
  2. torsion
  3. wind suction
  4. temperature
Show the answer

Answer: A. axial compression Spreads load to concrete.

Maximum slenderness for loaded compression members is

  1. 100
  2. 180
  3. 400
  4. 1000
Show the answer

Answer: B. 180 IS 800.

HSFG bolts transfer load by

  1. bearing only
  2. friction
  3. welding
  4. adhesive
Show the answer

Answer: B. friction Clamping force.

An ISA section is

  1. a rolled angle
  2. a rolled beam
  3. a channel
  4. a tube
Show the answer

Answer: A. a rolled angle Indian Standard Angle.

Shear lag affects mainly

  1. members connected through one leg
  2. solid slabs
  3. soil
  4. cables only
Show the answer

Answer: A. members connected through one leg Uneven stress in angles.

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →