IITIAN1997 STUDIO

Environmental engineering and sanitation

JLEE CE · 82 practice questions with answers

Practise and take a mock test →

Water supply, sewage and pollution

Topics: Environment and pollution; water demand, population forecasting, sources, intake; water quality and tests; purification (aeration, sedimentation, coagulation, filtration, disinfection); distribution; sewerage systems; sewage characteristics, treatment and disposal; sanitation.

Water demand and population

Design population is forecast by arithmetic increase (P = P₀ + n x̄), geometric increase (P = P₀(1 + r)ⁿ) or incremental methods. Demand per head: about 135 litres per capita per day for towns with full sewerage (CPHEEO). Fluctuations are covered by peak factors.

  • Arithmetic: P₀ + n x̄
  • Geometric: P₀(1 + r)ⁿ
  • 135 lpcd for sewered towns

Example: A town of 50 000 grows by 5000 a decade. Find the population after 3 decades (arithmetic).

  1. P = 50 000 + 3 × 5000.
  2. = 65 000.

Answer: 65 000

Example: Find the daily demand for 65 000 people at 135 lpcd.

  1. 65 000 × 135 = 8 775 000 L.
  2. ≈ 8.8 MLD.

Answer: ≈ 8.8 MLD

Water treatment

Treatment steps: screening, aeration (removes gases, oxidises iron), coagulation with alum and flocculation, sedimentation, rapid sand filtration, and disinfection by chlorine. Detention time of a tank = volume/flow. Chlorine dose = chlorine demand + residual (0.2 mg/L at the consumer end).

  • Detention time = V/Q
  • Alum coagulates fine particles
  • Dose = demand + residual

Example: A tank 20 × 10 × 3 m treats 300 m³/h. Find the detention time.

  1. V = 600 m³.
  2. t = 600/300 = 2 h.

Answer: 2 h

Example: A 10 MLD plant needs 1.8 mg/L demand plus 0.2 mg/L residual. Find the chlorine per day.

  1. Dose = 2 mg/L.
  2. 2 mg/L × 10 × 10⁶ L = 20 kg/day.

Answer: 20 kg/day

Sewage and its treatment

Sewage flow is roughly 80 % of the water supply. Its strength is measured by BOD (oxygen used by microbes in 5 days at 20 °C): BOD₅ = (D₁ − D₂)/P, where P is the dilution fraction. Treatment removes solids (primary) and dissolved organic matter (secondary: activated sludge, trickling filters, oxidation ponds).

  • Sewage ≈ 80 % of water supplied
  • BOD₅ = (D₁ − D₂)/P
  • Primary: settle; secondary: biological

Example: A 2 % dilution has DO 8 mg/L at first and 4 mg/L after 5 days. Find BOD₅.

  1. BOD = (8 − 4)/0.02.
  2. = 200 mg/L.

Answer: 200 mg/L

Water demand is population × per capita demand (commonly 135 litres per head per day in Indian towns). Treatment follows screening, aeration, sedimentation with coagulation (usually alum), filtration and disinfection by chlorine. A slow sand filter runs at about 100–200 L/h/m² and a rapid sand filter at 3000–6000 L/h/m². Sewage strength is measured by biochemical oxygen demand (BOD, standard 5-day test at 20 °C) and chemical oxygen demand (COD), with COD at least as large as BOD. Primary treatment settles solids; secondary treatment (activated sludge, trickling filter, oxidation pond) removes dissolved organics biologically. A septic tank serves individual houses.

  • Population forecasts: arithmetic, geometric and incremental increase methods.
  • Desirable pH of drinking water 6.5–8.5.
  • Hardness: temporary (bicarbonates, removed by boiling) and permanent (sulphates, chlorides).
  • E. coli and the MPN test indicate faecal contamination.
  • Detention time = tank volume/flow rate.

Key formulas

  • Demand = P × q
  • P_n = P₀ + nx̄
  • Detention time = V/Q
  • COD ≥ BOD

Practice questions

The common coagulant in water treatment is

  1. alum
  2. chlorine
  3. lime only
  4. ozone
Show the answer

Answer: A. alum Aluminium sulphate.

BOD is standardised over

  1. 1 day
  2. 5 days
  3. 10 days
  4. 30 days
Show the answer

Answer: B. 5 days At 20 °C.

Rapid sand filters compared with slow sand filters have

  1. a lower rate
  2. a higher rate
  3. the same rate
  4. no backwash
Show the answer

Answer: B. a higher rate About 30 times.

Disinfection is commonly done with

  1. alum
  2. chlorine
  3. lime
  4. carbon
Show the answer

Answer: B. chlorine Chlorination.

Temporary hardness is due to

  1. bicarbonates
  2. sulphates
  3. chlorides
  4. nitrates
Show the answer

Answer: A. bicarbonates Removed by boiling.

The desirable pH of drinking water is

  1. 2–4
  2. 6.5–8.5
  3. 9–11
  4. 12–14
Show the answer

Answer: B. 6.5–8.5 IS standard.

The MPN test detects

  1. hardness
  2. coliform bacteria
  3. turbidity
  4. fluoride
Show the answer

Answer: B. coliform bacteria Most probable number.

Which is a secondary sewage treatment?

  1. screening
  2. grit removal
  3. activated sludge
  4. primary settling
Show the answer

Answer: C. activated sludge Biological.

For the same sewage, COD is

  1. less than BOD
  2. at least equal to BOD
  3. always zero
  4. unrelated
Show the answer

Answer: B. at least equal to BOD Oxidises more material.

A septic tank is used for

  1. individual houses
  2. river intake
  3. city water supply
  4. rain gauging
Show the answer

Answer: A. individual houses On-site treatment.

Detention time of a tank equals

  1. Q/V
  2. V/Q
  3. V × Q
  4. V − Q
Show the answer

Answer: B. V/Q Volume/flow.

A commonly used domestic water demand in Indian towns is about

  1. 40 lpcd
  2. 135 lpcd
  3. 500 lpcd
  4. 1000 lpcd
Show the answer

Answer: B. 135 lpcd Litres per capita per day.

The earth’s atmosphere extends to a height of roughly ____ km.

  1. 10
  2. 200
  3. 1000
  4. 2000
Show the answer

Answer: B. 200

The lowest layer of the atmosphere, holding most of its mass, is the

  1. ionosphere
  2. troposphere
  3. stratosphere
  4. none of these
Show the answer

Answer: B. troposphere

Which of these is NOT a natural source of air pollution?

  1. Volcanic eruptions and lightening discharges.
  2. Biological decay of vegetable matter.
  3. Photochemical oxidation of organic matter.
  4. None of these.
Show the answer

Answer: D. None of these.

Which is a man-made source of air pollution?

  1. Automobile exhaust.
  2. Forest fire.
  3. Bacterial action in soil and swamp areas
  4. All (a), (b) and (c).
Show the answer

Answer: A. Automobile exhaust.

The largest share of air pollution comes from

  1. Industrial chimney exhaust.
  2. Forest fire.
  3. Automobiles exhaust.
  4. Photochemical oxidation of organic matter.
Show the answer

Answer: C. Automobiles exhaust.

For fish and other aquatic life, dissolved oxygen should not fall below about ____ ppm.

  1. 10000
  2. 5
  3. 500
  4. 1000
Show the answer

Answer: B. 5

Which of these is taken as the major constituent of air pollutants from industry?

  1. Oxides of sulphur
  2. Oxides of nitrogen
  3. Carbon monoxide
  4. Hydrogen sulphide
Show the answer

Answer: A. Oxides of sulphur

SO₂ in chimney gases causes

  1. respiratory & lung disease.
  2. reduction in plant's productivity owing to acid rain.
  3. corrosion of building materials.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Exposure to SO₂-laden flue gas leads to

  1. reduction in strength of leather & cloth.
  2. acceleration of corrosion rates of metals.
  3. increased drying & hardening time of paints.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Carbon monoxide is dangerous mainly because it causes

  1. respiratory disease (e.g. asthma).
  2. asphyxiation (suffocation) leading to death.
  3. retardation in crop growth.
  4. damage to building materials like marble.
Show the answer

Answer: B. asphyxiation (suffocation) leading to death.

Long exposure to high CO levels kills because CO

  1. of clotting of blood.
  2. of jamming of respiratory tract.
  3. it forms carboxyhaemoglobin by combining with haemoglobin of blood, thereby making it incapable of absorbing oxygen.
  4. it forms CO₂ by combining with oxygen present in the blood.
Show the answer

Answer: C. it forms carboxyhaemoglobin by combining with haemoglobin of blood, thereby making it incapable of absorbing oxygen.

Arrange nitrogen (A), argon (B), oxygen (C) and carbon dioxide (D) in decreasing order of their share in dry air.

  1. A, C, B,D
  2. A, D, B, C
  3. C, D, A, B
  4. A, C, D, B
Show the answer

Answer: A. A, C, B,D

Global warming can lead to

  1. flood
  2. cyclone
  3. decrease in food productivity
  4. all (a), (b) and (c)
Show the answer

Answer: D. all (a), (b) and (c)

Ozone is

  1. a primary pollutant.
  2. a secondary pollutant.
  3. impervious to ultra-violet rays.
  4. both (b) and (c)
Show the answer

Answer: D. both (b) and (c)

Smog is

  1. nothing but black smoke.
  2. a combination of smoke and fog.
  3. a liquid particle resulting from vapor condensation.
  4. a solid particle e.g. flyash.
Show the answer

Answer: B. a combination of smoke and fog.

Particles below 1 µm that stay suspended in air almost indefinitely are called

  1. fumes
  2. mists
  3. smoke
  4. aerosols
Show the answer

Answer: D. aerosols

Which of these is NOT a secondary air pollutant?

  1. Ozone
  2. Photochemical smog
  3. Sulphur dioxide
  4. All (a), (b) & (c)
Show the answer

Answer: C. Sulphur dioxide

Which pair is NOT classed as particulate pollutants?

  1. Dust & mists
  2. Smoke & fumes
  3. Photochemical smog & soot
  4. None of these
Show the answer

Answer: C. Photochemical smog & soot

The main source of carbon monoxide in air is

  1. industrial chimney exhaust.
  2. automobiles exhaust.
  3. photochemical reaction in polluted atmosphere.
  4. burning of domestic fuel.
Show the answer

Answer: B. automobiles exhaust.

Carcinogenic hydrocarbons in air at high levels cause

  1. cancer
  2. silicosis
  3. respiratory disease (e.g., asthma)
  4. reduced crop yield
Show the answer

Answer: A. cancer

Workers in cement plants and limestone quarries are prone to

  1. cancer
  2. asthma
  3. silicosis
  4. flourosis (bone disease)
Show the answer

Answer: C. silicosis

High levels of nitrogen dioxide in air cause

  1. cancer
  2. bronchitis
  3. asphyxiation
  4. corrosion
Show the answer

Answer: B. bronchitis

The bone disease fluorosis is linked to high levels of ____ in air.

  1. hydrocarbons
  2. hydrogen flouride
  3. hydrogen sulphides
  4. nitrogen dioxide
Show the answer

Answer: B. hydrogen flouride

Ozone and smog at high concentration cause

  1. embrittlement & decrease of folding resistance of paper.
  2. cracking of rubber products.
  3. fading of dye on textiles.
  4. damage of electrical insulator on high tension power line.
Show the answer

Answer: B. cracking of rubber products.

Hot, humid air rich in SO₂ causes

  1. fading of dyes on textiles.
  2. corrosion, tarnishing & soiling of metals.
  3. reduced strength of textiles.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Lead released by vehicles using leaded petrol causes

  1. paralysis of muscles & loss of appetite.
  2. nervous depression.
  3. gastroentisitis & diarrhea.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Which of these kills by asphyxiation when it exceeds about 50 ppm for long periods?

  1. Benzopyrene
  2. Peroxyacyl nitrate
  3. Carbon monoxide
  4. Sulphur dioxide
Show the answer

Answer: C. Carbon monoxide

For removing fly ash from flue gas in a thermal power station, the most suitable equipment is the

  1. gravity settling chamber
  2. cyclone separator
  3. electrostatic precipitator
  4. bag filter
Show the answer

Answer: C. electrostatic precipitator

Which adsorbent is commonly used to remove nitrogen oxides from gases?

  1. Active carbon
  2. Silica gel
  3. Bog iron (iron oxide)
  4. Pulverised limestone
Show the answer

Answer: B. Silica gel

Particles larger than about 75 µm are called

  1. grit
  2. dust
  3. powder
  4. smoke
Show the answer

Answer: A. grit

Carbon particles smaller than 1 µm are called

  1. grit
  2. aggregates
  3. aerosols
  4. smoke
Show the answer

Answer: D. smoke

Particles of 5–200 µm size are classed as

  1. colloids or aerosols
  2. powder
  3. dust
  4. smoke
Show the answer

Answer: A. colloids or aerosols

Material with 80 % finer than 200 mesh is called

  1. smoke
  2. powder
  3. grit
  4. aggregates
Show the answer

Answer: B. powder

Which of these is NOT emitted by volcanic eruptions?

  1. SO₂
  2. H₂S
  3. CO
  4. hydrocarbons
Show the answer

Answer: D. hydrocarbons

The main pollutant in automobile exhaust (among these) is

  1. SO₂
  2. CO₂
  3. NO
  4. hydrocarbons
Show the answer

Answer: C. NO

Which plant releases large amounts of SO₂?

  1. Nitric acid
  2. Sulphuric acid
  3. Chloralkali
  4. Iron & steel
Show the answer

Answer: B. Sulphuric acid

Which of these does NOT release much SO₂?

  1. Thermal power plant
  2. Petroleum refinery
  3. Nitric acid plant
  4. Sulphuric acid plant
Show the answer

Answer: C. Nitric acid plant

Besides CO₂, greenhouse gases include

  1. Methane
  2. Nitrous oxide
  3. Chlorofluro carbons (CFC)
  4. All (a), (b) and (c)
Show the answer

Answer: D. All (a), (b) and (c)

For sub-micron particles, the least efficient dust collector is the

  1. Dust catcher (gravity type)
  2. Cyclone separator
  3. Bag filter
  4. Hollow wet scrubber
Show the answer

Answer: A. Dust catcher (gravity type)

Photochemical smog from vehicle exhaust

  1. by reaction of hydrocarbon & nitric oxide in presence of sunlight.
  2. appears only on sunny days.
  3. is harmful for crops and trees also besides causing eye irritation & asthma.
  4. all (a), (b) & (c)
Show the answer

Answer: D. all (a), (b) & (c)

The threshold limit value (TLV) of SO₂ in air is about ____ ppm.

  1. 5
  2. 500
  3. 1000
  4. 2000
Show the answer

Answer: A. 5

The safe working limit of CO₂ in air is about ____ ppm.

  1. 50
  2. 1000
  3. 2000
  4. 5000
Show the answer

Answer: D. 5000

The TLV of carbon monoxide is about ____ ppm.

  1. 5
  2. 50
  3. 2000
  4. 5000
Show the answer

Answer: B. 50

Ammonia, NO₂ and phenol vapour each have a TLV of about ____ ppm.

  1. 5
  2. 100
  3. 1000
  4. 2000
Show the answer

Answer: A. 5

Life is in acute danger when CO₂ in air exceeds about ____ % by volume.

  1. 1
  2. 3
  3. 7
  4. 20
Show the answer

Answer: C. 7

SO₂ in air can be fatal above about ____ ppm.

  1. 20
  2. 100
  3. 400
  4. 200
Show the answer

Answer: C. 400

Death is very likely if CO in air exceeds about ____ ppm.

  1. 50
  2. 500
  3. 1000
  4. 3000 (i.e. 0.3%)
Show the answer

Answer: D. 3000 (i.e. 0.3%)

Above about ____ ppm of H₂S in air, life is in acute danger.

  1. 50
  2. 100
  3. 300
  4. 700
Show the answer

Answer: D. 700

Ozone and phosgene have a TLV of about ____ ppm.

  1. 0.1
  2. 25
  3. 100
  4. 1000
Show the answer

Answer: A. 0.1

Smoke from a furnace results from

  1. insufficient supply of combustion air and insufficient time for combustion.
  2. poor quality of fuel and improper mixing of fuel & combustion air.
  3. poor design & overloading of furnace.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

The Ringelmann chart is used to measure

  1. combustibles present in automobile exhaust.
  2. smoke density from a chimney.
  3. exhaust gas density.
  4. flue gas temperature.
Show the answer

Answer: B. smoke density from a chimney.

SO₂ has a noticeable pungent smell above roughly ____ ppm.

  1. 0.01
  2. 0.1
  3. 1
  4. 4
Show the answer

Answer: C. 1

Peroxyacyl nitrate (PAN) is a pollutant found in

  1. automobile exhaust.
  2. flue gas of coal based power plant.
  3. exhaust of nitric acid plant.
  4. exhaust of sulphuric acid plant.
Show the answer

Answer: A. automobile exhaust.

Which statement about BOD is wrong?

  1. Biological oxygen demand (BOD) is a characteristic and not a constituent of water.
  2. BOD is a measure of the amount of oxygen which will be demanded & used in 5 days by the biological decomposition of the organic matter.
  3. BOD is expressed in mg/litre (typically, BOD=2.5 mg/litre for potable water).
  4. none of these
Show the answer

Answer: D. none of these

Which statement about COD is correct?

  1. Chemical oxygen demand (COD) is a measure of chemically oxidisable organic matter present in water.
  2. COD is determined by oxidising the organic matter with potassium dichromate in concentrated sulphuric acid solution at boiling temperature.
  3. COD is related to BOD of a given waste in water but the relationship varies for different wastes.
  4. all (a), (b) and (c).
Show the answer

Answer: D. all (a), (b) and (c).

Among these, the most lethal water pollutants are

  1. Phenol and cynide
  2. Chlorine
  3. Alkalis
  4. Suspended solids
Show the answer

Answer: A. Phenol and cynide

Soluble organic matter in polluted water causes

  1. undesirable plants growth.
  2. depletion of oxygen.
  3. fire hazards.
  4. explosion hazards.
Show the answer

Answer: B. depletion of oxygen.

Non-biodegradable ABS from detergents in a stream causes

  1. fire hazards.
  2. explosion hazards.
  3. persistent foam.
  4. depletion of dissolved oxygen.
Show the answer

Answer: C. persistent foam.

Raw municipal sewage typically has a BOD of about ____ mg/L.

  1. 1-2
  2. 5-10
  3. 150-300
  4. 2000-3000
Show the answer

Answer: C. 150-300

The COD of raw municipal sewage is typically in the range of about ____ mg/L.

  1. 1-2
  2. 5-10
  3. 150-300
  4. 1500-2500
Show the answer

Answer: C. 150-300

Drinking water can be disinfected using

  1. ozone and iodine.
  2. chlorine or its compounds
  3. ultraviolet light for irradiation of water.
  4. all (a), (b) & (c).
Show the answer

Answer: D. all (a), (b) & (c).

Which of these does NOT lower the surface tension of water?

  1. Fat
  2. Soap
  3. Detergent
  4. Surfactant
Show the answer

Answer: A. Fat

A water-vapour concentration of 1 % in air equals ____ ppm.

  1. 10000
  2. 1000
  3. 100
  4. 10
Show the answer

Answer: A. 10000

Freezing 1 ton of water at 0 °C into ice at 0 °C in 24 hours needs a cooling rate of about ____ BTU per minute.

  1. 100
  2. 200
  3. 1000
  4. 2000
Show the answer

Answer: B. 200

The usual chlorine dose in public water supply is about ____ ppm.

  1. 0.5 to 1
  2. 10 to 15
  3. 300 to 500
  4. 1000 to 1500
Show the answer

Answer: A. 0.5 to 1

New wells are disinfected with chlorine supplied as

  1. sodium chloride
  2. sodium hypochlorate
  3. bleaching powder
  4. aluminium chloride
Show the answer

Answer: C. bleaching powder

Which substance is less dense as a solid than as a liquid?

  1. carbon dioxide
  2. water
  3. mercury
  4. none of these.
Show the answer

Answer: B. water

Which of these is a natural buffer solution?

  1. mercury
  2. lime water
  3. human blood
  4. concentrated nitric acid
Show the answer

Answer: C. human blood

Chlorine bleaches only when ____ is present.

  1. dry air
  2. pure oxygen
  3. moisture
  4. sun light
Show the answer

Answer: C. moisture

An aluminium ball quenched in water at 40 °C cools from 550 °C to 450 °C in 20 s. After another 20 s it will be at about ____ °C.

  1. 370
  2. 340
  3. 320
  4. 300
Show the answer

Answer: A. 370

The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.

Practise and take a mock test →