Cement, aggregates, fresh and hardened concrete
Topics: Cement composition, hydration, fineness, setting times, soundness, grades and tests; water quality; aggregates; grades of concrete, durability, water–cement ratio; workability and slump test; compressive and flexural strength; mix design; curing, admixtures, special concretes.
Cement
Ordinary Portland cement is made by burning limestone and clay to clinker and grinding it with gypsum. Its main compounds (Bogue): C₃S (early strength), C₂S (later strength), C₃A (flash set, controlled by gypsum, heat) and C₄AF. OPC grades 33, 43 and 53 give their 28-day mortar strength in N/mm².
Tests: fineness, normal consistency (Vicat), initial setting time at least 30 min and final at most 600 min, soundness (Le Chatelier expansion at most 10 mm) and compressive strength.
- C₃S early strength; C₂S later strength
- Initial set ≥ 30 min; final ≤ 600 min
- Le Chatelier expansion ≤ 10 mm
Example: Which cement compound gives most of the strength in the first week?
- C₃S hydrates quickly.
- C₃S.
Answer: C₃S
Example: Why must the initial setting time not be too short?
- Concrete must be mixed, transported, placed and compacted before it stiffens.
- At least 30 minutes is allowed for this.
Answer: To allow time for placing
Aggregates, water–cement ratio and workability
Abrams’ law: for fully compacted concrete, strength falls as the water–cement ratio rises. Workability (ease of placing) is checked by the slump test (or compaction factor, Vee-Bee); true slump is wanted, shear slump means a harsh mix, collapse slump a very wet one.
Fineness modulus = sum of cumulative percentages retained on standard sieves ÷ 100; fine sand 2.2–2.6, medium 2.6–2.9, coarse 2.9–3.2.
- Strength ↓ as w/c ↑ (Abrams)
- Slump: true, shear, collapse
- FM = Σ cumulative % retained/100
Example: A mix uses 400 kg of cement at w/c = 0.45. How much water?
- Water = 0.45 × 400.
- = 180 kg (180 L).
Answer: 180 kg
Example: Cumulative percentages retained on the standard sieves add up to 275. Find the fineness modulus.
- FM = 275/100.
- = 2.75 (medium sand).
Answer: 2.75
Grades, mix design and curing
Grade M20 means a characteristic 28-day cube strength of 20 N/mm² (5 % of results may fall below it). Mix design targets a mean strength f_ck + 1.65s. Nominal mixes: M15 1:2:4, M20 1:1.5:3. Curing (keeping concrete moist for at least 7 days for OPC) lets hydration continue and prevents cracks.
Admixtures: plasticisers and superplasticisers raise workability, accelerators speed setting, retarders slow it, air-entraining agents improve freeze–thaw resistance.
- Target mean = f_ck + 1.65s
- M20 nominal 1:1.5:3
- Cube strength = load/area (150 mm cube)
Example: For M20 with standard deviation 4 N/mm², find the target mean strength.
- f_t = 20 + 1.65 × 4.
- = 26.6 N/mm².
Answer: 26.6 N/mm²
Example: A 150 mm cube fails at 675 kN. Find its strength.
- Area = 150 × 150 = 22 500 mm².
- 675 000/22 500 = 30 N/mm².
Answer: 30 N/mm²
Portland cement contains C₃S (early strength), C₂S (later strength), C₃A (flash set, controlled by gypsum) and C₄AF. IS limits: initial setting at least 30 min and final setting at most 10 h. Strength depends mainly on the water–cement ratio (Abrams’ law): less water gives more strength, as long as the concrete can be fully compacted. Workability is checked by slump, compaction factor and Vee-Bee tests. Grade M20 has a characteristic 28-day cube strength of 20 N/mm²; IS 456 requires at least M20 for reinforced concrete. Curing keeps concrete moist so hydration continues, for at least 7 days with OPC.
- Tests: Vicat (consistency, setting), Le Chatelier (soundness), fineness by sieve or Blaine.
- Nominal mix M20 is about 1:1.5:3.
- Plasticisers improve workability; accelerators such as CaCl₂ speed setting; retarders slow it.
- Segregation is separation of aggregate; bleeding is water rising to the surface.
- f_cr = 0.7√fck; Ec = 5000√fck; target mean strength = fck + 1.65S.
Key formulas
- w/c = water/cement (by mass)
- f_cr = 0.7√fck
- Ec = 5000√fck
- f′ck = fck + 1.65S
Practice questions
Initial setting time of OPC should be at least
- 10 min
- 30 min
- 60 min
- 600 min
Show the answer
Answer: B. 30 min IS 269.
Soundness of cement is tested by
- Vicat apparatus
- Le Chatelier apparatus
- slump cone
- Blaine apparatus
Show the answer
Answer: B. Le Chatelier apparatus Le Chatelier.
Gypsum is added to cement to
- speed up setting
- control setting
- colour it
- increase heat
Show the answer
Answer: B. control setting Controls flash set.
The compound giving early strength is
- C₃S
- C₂S
- C₄AF
- gypsum
Show the answer
Answer: A. C₃S C₃S.
Abrams’ law relates strength to
- aggregate size
- water–cement ratio
- cement fineness
- slump
Show the answer
Answer: B. water–cement ratio w/c ratio.
Workability is commonly measured by the
- slump test
- cube test
- Vicat test
- Le Chatelier test
Show the answer
Answer: A. slump test Slump cone.
The size of the standard cube for concrete is
- 100 mm
- 150 mm
- 200 mm
- 70 mm
Show the answer
Answer: B. 150 mm 150 mm.
Minimum grade for reinforced concrete under IS 456 is
- M10
- M15
- M20
- M30
Show the answer
Answer: C. M20 M20.
Water rising to the surface of fresh concrete is
- segregation
- bleeding
- creep
- shrinkage
Show the answer
Answer: B. bleeding Bleeding.
Calcium chloride in concrete acts as
- an accelerator
- a retarder
- an air-entrainer
- a plasticiser
Show the answer
Answer: A. an accelerator Speeds hydration.
M25 concrete means characteristic strength at 28 days of
- 25 N/mm²
- 25 kg/cm²
- 250 N/mm²
- 2.5 N/mm²
Show the answer
Answer: A. 25 N/mm² Cube strength.
Minimum curing for OPC concrete is about
- 1 day
- 3 days
- 7 days
- 28 days
Show the answer
Answer: C. 7 days IS 456.
The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.