Materials, masonry, foundations and finishes
Topics: Stones and bricks, sand and mortars, timber and miscellaneous materials, painting and varnishing; foundations, masonry, doors and windows, damp proofing and floors, plastering and pointing; excavation, pile foundations, building planning and bye-laws, fire protection and acoustics.
Bricks, stones and mortar
A standard modular brick is 190 × 90 × 90 mm (200 × 100 × 100 mm with mortar), so about 500 bricks make a cubic metre of brickwork. First-class bricks are well burnt, give a ringing sound, absorb less than about 20 % water by weight and have a crushing strength above about 10 N/mm².
Mortar binds masonry: cement mortar (1:3 to 1:6), lime mortar, or mud. Dry materials shrink when mixed with water, so the dry volume is taken as about 1.27 times the wet volume of mortar.
- Modular brick 190 × 90 × 90 mm
- ≈ 500 bricks per m³ of brickwork
- Dry volume of mortar ≈ 1.27 × wet volume
Example: How much cement is needed for 1 m³ of 1:6 cement mortar?
- Dry volume ≈ 1.27 m³; cement share = 1.27/7 ≈ 0.181 m³.
- × 1440 kg/m³ ≈ 261 kg ≈ 5.2 bags of 50 kg.
Answer: ≈ 261 kg (about 5 bags)
Example: How many modular bricks are needed for 10 m³ of brickwork?
- Each brick with mortar occupies 0.2 × 0.1 × 0.1 = 0.002 m³, i.e. 500 per m³.
- 10 × 500 = 5000 bricks (plus a few per cent for breakage).
Answer: ≈ 5000
Timber, paints and foundations
Timber must be seasoned (dried) to a moisture content of about 10–15 % before use to prevent shrinkage, warping and decay; moisture content = (wet mass − dry mass)/dry mass. Paints have a base (white lead, zinc oxide), a vehicle (linseed oil), a pigment, a drier and a thinner.
Foundations spread the load to soil the ground can carry: shallow (spread, strip, raft) where good soil is near the surface; deep (piles, wells) where it is not.
- Moisture content on dry mass
- Paint: base, vehicle, pigment, drier, thinner
- Shallow vs deep foundations
Example: A timber sample weighs 120 g and 100 g after oven drying. Find its moisture content.
- MC = (120 − 100)/100.
- = 20 %.
Answer: 20 %
Damp proofing, plastering and stairs
A damp-proof course (DPC), typically cement concrete with a waterproofing compound or bitumen, is laid at plinth level to stop moisture rising by capillarity. Plastering protects and finishes walls (12 mm on the inside face is common); pointing finishes only the joints.
Stairs are comfortable when twice the riser plus the tread is about 600 mm (2R + T ≈ 600), with risers of 150–175 mm.
- DPC at plinth level
- 2R + T ≈ 600 mm
- Riser 150–175 mm
Example: With a 150 mm riser, what tread suits the 2R + T rule?
- T = 600 − 2 × 150.
- = 300 mm.
Answer: 300 mm
Example: How many risers are needed for a floor height of 3 m with 150 mm risers?
- 3000/150.
- = 20 risers.
Answer: 20
A standard modular brick is 19 × 9 × 9 cm (20 × 10 × 10 cm with mortar); first-class bricks absorb no more than 20% water and have compressive strength of at least 10.5 N/mm². In English bond, alternate courses are all headers and all stretchers, and a queen closer starts the header course to break vertical joints; Flemish bond alternates headers and stretchers within each course. Mortar is cement or lime with sand, for example 1:6. Timber is seasoned to reduce moisture and warping. Spread, raft and pile foundations carry progressively larger loads or weaker soils. A damp-proof course at plinth level stops rising moisture.
- Frog: indentation on a brick that holds mortar and shows the maker’s mark.
- Stones: igneous (granite), sedimentary (sandstone, limestone), metamorphic (marble, slate).
- Queen closer: brick cut lengthwise in half; king closer: one corner cut off.
- Paint: base, vehicle, pigment, drier, thinner.
- Bulking of sand peaks at about 4–6% moisture.
Key formulas
- Bricks per m³ ≈ 500 (modular, with mortar)
- 1 m³ cement ≈ 28.8 bags (50 kg, 1440 kg/m³)
Practice questions
The nominal size of a modular brick is
- 19 × 9 × 9 cm
- 20 × 10 × 10 cm
- 23 × 11 × 7 cm
- 25 × 12 × 8 cm
Show the answer
Answer: B. 20 × 10 × 10 cm Actual 19 × 9 × 9 cm plus joints.
Water absorption of a first-class brick should not exceed
- 5%
- 20%
- 30%
- 40%
Show the answer
Answer: B. 20% By weight, after 24 h.
The indentation on a brick is the
- closer
- frog
- bat
- bond
Show the answer
Answer: B. frog Frog.
Alternate courses of headers and stretchers is
- English bond
- Flemish bond
- stretcher bond
- header bond
Show the answer
Answer: A. English bond Strongest common bond.
A brick cut lengthwise into two halves is a
- king closer
- queen closer
- bat
- bevelled closer
Show the answer
Answer: B. queen closer Queen closer.
Marble is a
- igneous rock
- sedimentary rock
- metamorphic rock
- volcanic rock
Show the answer
Answer: C. metamorphic rock Metamorphosed limestone.
Seasoning of timber is done to
- increase moisture
- reduce moisture
- add colour
- increase weight
Show the answer
Answer: B. reduce moisture Prevents warping and decay.
For weak soil with a deep firm stratum, the suitable foundation is
- strip footing
- pile foundation
- isolated footing
- stepped footing
Show the answer
Answer: B. pile foundation Transfers load to depth.
A damp-proof course is usually provided at
- roof level
- plinth level
- lintel level
- sill level
Show the answer
Answer: B. plinth level Stops rising damp.
The main constituent giving body to a paint is the
- base
- vehicle
- drier
- thinner
Show the answer
Answer: A. base For example white lead.
Pointing is the finishing of
- floors
- mortar joints
- roof tiles
- door frames
Show the answer
Answer: B. mortar joints Exposed joints.
Bulking of sand is maximum at moisture of about
- 1%
- 5%
- 15%
- 30%
Show the answer
Answer: B. 5% Disappears when saturated.
The practice questions were written for this studio; they are not copied from ASTU papers. ASTU publishes no topic syllabus for these exams, so the topics are an informed guide based on diploma courses, not an official list.