Carpentry shop
Topics: Wood, tools and machines; simple joints; utility job.
Timber, tools and joints
Carpentry shapes wood into useful articles. Timber is hardwood (such as teak and sal, strong and durable) or softwood (such as pine, easier to work). Plywood is made of thin veneers glued with their grains crossed, so it does not split easily and is stable in size. Freshly cut timber holds a lot of water and must be seasoned, dried slowly in air or in a kiln, or it will shrink, warp and crack later.
Tools fall into groups: marking and measuring (steel rule, try square, marking gauge), cutting (rip saw along the grain, cross-cut saw across it, tenon saw for fine joints), planing (jack plane), boring (brace and bits, hand drill), chiselling (firmer and mortise chisels) and striking (mallet). The carpentry vice holds the work.
Joints join pieces strongly. A lap joint halves each piece where they cross; a mortise and tenon fits a tongue into a slot, as in the diagram, and is used in door and window frames; a dovetail’s flared tongues cannot be pulled apart, so it suits drawers. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Hardwood: teak, sal. Softwood: pine
- Seasoning: air or kiln drying
- Rip saw: along the grain. Cross-cut: across it
- Joints: lap, mortise and tenon, dovetail, bridle
- Mallet, not a hammer, on chisels
Example: A plank weighs 12 kg when cut and 10 kg when oven-dry. Find its moisture content.
- Moisture content = (wet − dry)/dry × 100.
- (12 − 10)/10 × 100.
Answer: 20%
Example: Find the volume of a 2 m plank, 250 mm wide and 50 mm thick, and its cost at ₹60 000 per m³.
- Volume = 2 × 0.25 × 0.05 = 0.025 m³.
- Cost = 0.025 × 60 000.
Answer: 0.025 m³, costing ₹1500
Example: Which joint would you choose for the corners of a drawer, and why?
- A drawer front is pulled every time it opens.
- A dovetail’s flared tongues lock against that pull.
Answer: A dovetail joint
Carpentry works timber and plywood into useful shapes. Timber must be seasoned to remove moisture, which prevents warping and cracks. Tools fall into marking, cutting, planing, boring, striking and holding groups. Common joints include lap, mortise and tenon, and dovetail.
- Hardwoods include sal and teak; softwoods include pine and deodar.
- A try square checks right angles; a marking gauge marks parallel lines.
- Sharp tools are safer than blunt ones.
- Air seasoning is slow, while kiln seasoning is quick and controlled.
Practice questions
Seasoning of timber removes
- moisture
- colour
- bark only
- grain
Show the answer
Answer: A. moisture To reduce warping.
A try square checks
- right angles
- weight
- moisture
- hardness
Show the answer
Answer: A. right angles Its use.
Which is a carpentry joint?
- mortise and tenon
- butt weld
- socket
- elbow
Show the answer
Answer: A. mortise and tenon Woodwork joint.
A marking gauge
- marks parallel lines
- cuts timber
- drills
- polishes
Show the answer
Answer: A. marks parallel lines Its use.
Theory questions
Why is timber seasoned? (2 marks)
Show the model answer
To remove moisture, which reduces warping, shrinkage and decay and makes the timber stronger.
Describe the tools used in a carpentry shop and the safety rules to follow. (8 marks)
Show the model answer
Marking: try square, marking gauge. Cutting: saws and chisels. Planing: jack plane. Boring: brace and bit, gimlet. Striking: mallet and hammer. Holding: bench vice and clamps. Safety: keep tools sharp and in their place, cut away from the body, secure the job and wear suitable clothes.
Fitting shop
Topics: Marking, measuring, cutting, holding tools; filing, drilling and fitting.
Measuring, marking and fitting
The fitting shop makes metal parts fit together by hand. The work is marked out on a surface plate with a scriber, try square, dividers and a centre punch, then cut with a hacksaw, filed to the line, drilled and tapped. Files are classed by length, cut (rough, bastard, second cut, smooth) and shape (flat, square, round, half-round, triangular).
Precise measuring tools are essential. A vernier caliper has a sliding scale whose divisions are slightly shorter than the main scale’s; the least count is the difference between one main-scale and one vernier division. A micrometer turns a fine screw: its least count is the pitch divided by the number of thimble divisions, usually 0.5 mm/50 = 0.01 mm.
Internal threads are cut with a set of taps, after drilling a tap-drill hole of about the thread’s diameter minus its pitch. External threads are cut with a die. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Least count (vernier) = 1 MSD − 1 VSD
- Reading = main scale + matching line × least count
- Micrometer LC = pitch/divisions = 0.01 mm
- Tap drill ≈ D − p
- Files: rough, bastard, second cut, smooth
Example: A caliper has 50 vernier divisions equal to 49 mm. Find its least count, and the reading if the main scale shows 24 mm and the 7th vernier line matches.
- 1 VSD = 49/50 = 0.98 mm, so LC = 1 − 0.98 = 0.02 mm.
- Reading = 24 + 7 × 0.02.
Answer: LC 0.02 mm; reading 24.14 mm
Example: A micrometer shows 7.5 mm on the sleeve and 23 on the thimble. What is the reading?
- LC = 0.5/50 = 0.01 mm.
- 7.5 + 23 × 0.01.
Answer: 7.73 mm
Example: Find the tap-drill size for an M10 × 1.5 thread.
- Tap drill ≈ D − p.
- 10 − 1.5.
Answer: 8.5 mm
Fitting makes and assembles metal parts by hand. Marking uses a surface plate, try square, scriber, dot punch and height gauge. Cutting uses hacksaws and chisels; filing brings the job to size. Drilling makes holes, and taps and dies cut threads. A bench vice holds the work.
- Hacksaw teeth point forward, and cutting occurs on the push stroke.
- Files are classed by cut: rough, bastard, second and smooth.
- A centre punch guides the drill.
- Vernier calipers measure to about 0.02 mm.
Practice questions
A hacksaw cuts on the
- forward stroke
- return stroke
- both strokes
- neither
Show the answer
Answer: A. forward stroke Teeth point forward.
A tap cuts
- internal threads
- external threads
- wood
- plastic only
Show the answer
Answer: A. internal threads A die cuts external ones.
A surface plate is used for
- marking reference
- welding
- cooling
- painting
Show the answer
Answer: A. marking reference A flat datum.
A centre punch is used
- before drilling
- after painting
- for welding
- for bending
Show the answer
Answer: A. before drilling It locates the drill.
Theory questions
Distinguish between a tap and a die. (2 marks)
Show the model answer
A tap cuts internal threads, and a die cuts external threads.
Name the marking, measuring, cutting and holding tools in a fitting shop and give the steps to make a square from a metal piece. (8 marks)
Show the model answer
Marking and measuring: surface plate, try square, scriber, dot punch, Vernier caliper. Cutting: hacksaw, chisel, files. Holding: bench vice. Steps: file one side flat, check with a try square, mark the other sides with a scriber, dot-punch the lines, then saw and file to size, checking squareness and dimensions.
Plumbing shop
Topics: GI and PVC pipes and fittings; threading; simple job.
Pipes, fittings and drains
Plumbing carries clean water in and waste water out. Supply pipes are GI (galvanised iron), CPVC or PVC; drains and soil pipes are PVC or cast iron. Pipes are joined by fittings: couplings join two pipes, elbows and bends change direction, tees branch off, reducers change size, unions allow pipes to be taken apart, and caps and plugs close ends.
GI pipes are joined with threaded ends: the pipe is held in a pipe vice, cut with a pipe cutter, threaded with dies, and screwed into fittings using sealing tape. PVC pipes are cut, cleaned and joined with solvent cement. Taps and valves control the flow.
Drains must slope steadily so waste flows by gravity, and traps (U-bends) hold water to stop foul gases coming back. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Supply: GI, CPVC, PVC. Drains: PVC, cast iron
- Fittings: coupling, elbow, bend, tee, reducer, union, cap, plug
- GI: cut, thread, seal with tape
- PVC: solvent cement
- Drains slope; traps keep gases out
Example: A 12 m drain is laid at 1 in 40. How much does it fall?
- Fall = length/40.
- 12/40.
Answer: 0.3 m (300 mm)
Example: An overhead tank measures 1.5 m × 1 m × 1 m inside. How many litres does it hold?
- Volume = 1.5 m³.
- 1 m³ = 1000 L.
Answer: 1500 L
Example: Which fitting would you use to take a branch line off a straight pipe?
- A branch needs three openings.
- A tee has a straight run and a side outlet.
Answer: A tee
Plumbing installs pipes for water and waste. GI, PVC and flexible pipes are common. Tools include pipe wrenches, a pipe vice, hacksaw, and dies for threading. Fittings include sockets, elbows, tees, unions, reducers and valves. A pipeline is checked for leaks after it is assembled.
- A union allows a pipe to be removed easily.
- PVC pipes are joined with solvent cement.
- Use Teflon tape on threaded joints.
- A tee makes a branch; an elbow changes direction.
Practice questions
A tee is used to
- make a branch
- stop flow
- heat water
- cut pipe
Show the answer
Answer: A. make a branch Definition.
PVC pipes are joined with
- solvent cement
- arc welding
- rivets
- nails
Show the answer
Answer: A. solvent cement Chemical bond.
An elbow
- changes direction
- reduces pressure only
- holds a tap only
- cuts threads
Show the answer
Answer: A. changes direction Definition.
Threads on GI pipes are cut with a
- die
- chisel
- file only
- saw only
Show the answer
Answer: A. die External threads.
Theory questions
Name four pipe fittings and their uses. (3 marks)
Show the model answer
Socket joins two pipes; elbow changes direction; tee makes a branch; union allows easy dismantling.
Describe how to install water supply from a tank to a wash basin with GI pipes. (8 marks)
Show the model answer
Draw a line diagram and measure lengths. Cut pipes with a hacksaw, ream and thread them with a die. Apply Teflon tape and connect with sockets, elbows, a union and valve, tightening with wrenches. Fix them with clamps, connect the tap, fill the system and check every joint for leaks.
RCC shop
Topics: Materials, tools, bonds, bending and binding of rods, plinth layout, curing.
Concrete and reinforcement
Concrete is a mix of cement, sand (fine aggregate), stone chips (coarse aggregate) and water. Cement and water react and harden, binding the aggregates. A nominal mix is written by volume, such as 1 : 2 : 4 (cement : sand : aggregate), and the water–cement ratio, often about 0.5, controls strength: more water makes it easier to place but weaker.
Concrete is very strong when squeezed but weak when pulled. In a loaded beam, the top is squeezed and the bottom stretched, so steel bars are placed near the bottom to carry the tension: reinforced cement concrete (RCC). Stirrups hold the bars in place and resist shear.
Work in the RCC shop follows formwork, bending and tying steel, mixing, placing, compacting with a vibrator or tamping rod, and curing by keeping the concrete wet for about two weeks so it gains strength. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Concrete: cement + sand + aggregate + water
- Nominal mix 1 : 2 : 4; w/c about 0.5
- Strong in compression, weak in tension
- Steel bars at the tension side; stirrups for shear
- Formwork, steel, mix, place, compact, cure
Example: Estimate the cement for 1 m³ of 1 : 2 : 4 concrete. (Take dry volume = 1.54 × wet volume, and cement at 1440 kg/m³.)
- Dry volume = 1.54 m³; cement share = 1.54/7 = 0.22 m³.
- Mass = 0.22 × 1440 = 316.8 kg.
- In 50 kg bags: 316.8/50.
Answer: About 317 kg, or 6.3 bags
Example: With a water–cement ratio of 0.5, how much water does that cement need?
- Water = 0.5 × 316.8 kg.
- 1 kg of water ≈ 1 L.
Answer: About 158 L
Reinforced cement concrete combines concrete, which is strong in compression, with steel, which is strong in tension. Materials are cement, sand, aggregate, water and steel bars. Bars are cut, bent and tied into stirrups and cages. Concrete is mixed in a set proportion such as 1:2:4, compacted and cured. Masonry uses different bonds.
- Curing keeps concrete moist for strength, usually at least 7 days.
- A vibrator removes air from the mix.
- Too much water weakens concrete.
- English and Flemish are common brick bonds.
Practice questions
Concrete is strong in
- compression
- tension
- bending alone
- torsion alone
Show the answer
Answer: A. compression Steel handles tension.
Curing keeps concrete
- moist
- dry
- hot
- frozen
Show the answer
Answer: A. moist For hydration.
Mix 1:2:4 means cement : sand :
- aggregate
- water
- steel
- lime
Show the answer
Answer: A. aggregate By volume.
Stirrups are
- bent bars holding main steel
- pipes
- bricks
- tiles
Show the answer
Answer: A. bent bars holding main steel They resist shear.
Theory questions
Why is steel placed in concrete? (2 marks)
Show the model answer
Concrete is weak in tension, so steel carries the tensile force.
Describe the steps of casting an RCC beam, from materials to curing. (8 marks)
Show the model answer
Make the formwork and oil it. Cut, bend and tie the main bars and stirrups and place them with cover blocks. Mix cement, sand and aggregate in the given proportion with water. Pour, then compact with a vibrator. Remove the formwork when it has gained enough strength, and cure with water for at least 7 days.
Painting shop
Topics: Paint, resins, varnishes; wood and metal surfaces; spray painting.
Painting and finishing
Paint protects surfaces from rust and weather and makes them look good. It contains a binder (which forms the film), pigment (colour and body), solvent or thinner (to help it spread), and additives. Enamels give a hard glossy finish; emulsions are water-based for walls; varnishes are clear finishes for wood.
Most paint failures come from poor surface preparation. Metal must be cleaned of grease and rust, by wire brush, emery paper or sand blasting. A primer is applied first to grip the surface and, on steel, stop rust; then an undercoat to hide and level; then one or two finish coats, each allowed to dry.
Paint can be applied by brush, roller or spray gun. Common defects include blistering, peeling, runs and sags, and brush marks. Work in good ventilation, as solvents give off harmful vapours. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Paint: binder, pigment, solvent, additives
- Steps: clean, prime, undercoat, finish coats
- Brush, roller or spray
- Defects: blistering, peeling, runs, brush marks
- Ventilate; solvents are harmful
Example: A 4 m × 3 m wall needs two coats. If 1 L covers 12 m² per coat, how much paint is needed?
- Area per coat = 12 m², so two coats = 24 m².
- 24/12.
Answer: 2 L
Example: Paint on a steel gate peels off in flakes within months. What was probably skipped?
- Peeling usually means the paint did not bond to the surface.
- Rust and grease were not removed, or no primer was used.
Answer: Surface cleaning and priming
Paint protects a surface and improves its look. It has a base, pigment, vehicle (binder), thinner and drier. A surface is cleaned and primed, followed by undercoats and a finish coat. Varnish is a transparent coating, usually based on resin. Tools include brushes, rollers, scrapers and spray guns.
- Sandpaper smooths wood before painting.
- Primer helps paint stick and resists rust.
- Spray painting needs ventilation and a mask.
- Clean brushes after use.
Practice questions
Primer is applied
- first
- last
- never
- after polish
Show the answer
Answer: A. first To help paint stick.
Varnish is usually
- transparent
- opaque black
- powdered
- metallic only
Show the answer
Answer: A. transparent It shows the grain.
A pigment gives paint its
- colour
- smell
- weight only
- wetness
Show the answer
Answer: A. colour Definition.
Spray painting needs
- ventilation and a mask
- a welder
- a lathe
- nothing
Show the answer
Answer: A. ventilation and a mask Fumes are harmful.
Theory questions
Name the constituents of paint. (3 marks)
Show the model answer
Base, pigment, vehicle (binder), thinner and drier.
Describe how to paint a new metal surface by spray gun. (8 marks)
Show the model answer
Remove grease and rust with a scraper, wire brush and sandpaper. Mix the primer and fill the spray gun, connect the compressor, and spray evenly at a steady distance. Let it dry and rub lightly. Apply the finish coat in overlapping strokes. Work in a ventilated area with a mask and clean the gun after use.
Welding shop
Topics: Arc and gas welding, gas cutting; rods and flames; safety.
Arc and gas welding
Welding joins metals by melting their edges together, usually with a filler metal. In arc welding, an electric arc between a coated electrode and the work gives intense heat; the coating melts to form gas and slag that shield the hot weld from the air. AC transformers or DC sets supply the current, which is chosen by electrode size and job thickness.
Gas welding burns acetylene with oxygen in a torch, giving a flame of about 3200 °C. A neutral flame (equal oxygen and acetylene) suits most steels; a carburising flame has excess acetylene, and an oxidising flame excess oxygen, used for brass. Common joints are butt, lap, corner, T and edge.
Welding produces ultraviolet light, sparks, fumes and very hot metal. Always use a proper welding shield with the right filter glass, leather gloves and apron, keep fuel gas cylinders upright and away from heat, and never look at an arc with bare eyes. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Arc: electrode + arc + flux coating + slag
- Gas: oxy-acetylene, about 3200 °C
- Flames: neutral, carburising, oxidising
- Joints: butt, lap, corner, T, edge
- Heat input = ηVI/v
Example: An arc runs at 25 V and 150 A with 80% efficiency, moving at 5 mm/s. Find the heat input per mm.
- Heat input = ηVI/v = 0.8 × 25 × 150/5.
- = 3000/5.
Answer: 600 J/mm
Example: Which flame would you use for welding mild steel?
- Mild steel should not gain carbon or be oxidised.
- A neutral flame does neither.
Answer: A neutral flame
Welding joins metals by heat, with or without pressure and filler. Arc welding uses an electric arc and a coated electrode. Gas welding uses an oxy-acetylene flame, which may be neutral, oxidising or carburising. TIG and MIG use a gas shield, while spot and seam welding are resistance processes. Joints are lap, butt, T, corner and edge.
- The flux coating on an electrode protects the weld and stabilises the arc.
- A neutral flame suits most steel.
- Defects include porosity, undercut, slag inclusion and cracks.
- Always wear a helmet, gloves and an apron.
Practice questions
An oxy-acetylene flame with equal gases is
- neutral
- oxidising
- carburising
- cold
Show the answer
Answer: A. neutral Most common.
MIG welding uses a
- consumable wire with shielding gas
- wood electrode
- water jet
- hammer
Show the answer
Answer: A. consumable wire with shielding gas Metal inert gas.
A common welding defect is
- porosity
- polishing
- annealing
- painting
Show the answer
Answer: A. porosity Gas holes.
Which is a resistance welding process?
- spot welding
- arc welding
- gas welding
- TIG
Show the answer
Answer: A. spot welding Current and pressure.
A helmet protects from
- arc rays
- noise only
- rain
- dust only
Show the answer
Answer: A. arc rays UV and glare.
Theory questions
Name the three types of oxy-acetylene flame. (2 marks)
Show the model answer
Neutral, oxidising and carburising (reducing).
Compare arc and gas welding. List the safety precautions and common defects. (8 marks)
Show the model answer
Arc welding uses an electric arc and electrode, is faster and suits thick sections. Gas welding uses an oxy-acetylene flame, suits thin sheets and gives better control. Precautions: helmet, gloves, ventilation, no flammable materials nearby and checks of gas leaks. Defects: porosity, undercut, slag inclusion, cracks.
Machine and turning shops
Topics: Lathe and other machine tools; turning, facing and related operations (two shops in the syllabus).
The lathe and machining
A machine shop removes metal as chips to make accurate parts. The centre lathe turns the work while a single-point tool moves along or across it. Its main parts are the bed, headstock (with the spindle and speed gears), tailstock, carriage (with the tool post) and lead screw. Operations include facing, plain and step turning, taper turning, drilling, knurling and thread cutting.
The cutting speed is the speed of the work surface past the tool: V = πDN/1000 in m/min, with D in mm and N in rpm. Each material and tool has a suitable cutting speed, so a larger diameter needs a lower spindle speed. The feed is how far the tool moves per revolution, and the time for a cut is the length divided by the feed rate.
A taper can be turned by swivelling the compound rest to half the taper angle, where tan α = (D − d)/(2L). Other machines include the drilling machine, shaper, milling machine and grinder. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- V = πDN/1000 (m/min)
- N = 1000V/(πD)
- Time = L/(fN)
- Taper: tan α = (D − d)/(2L)
- Lathe parts: bed, headstock, tailstock, carriage, lead screw
Example: A 50 mm bar turns at 400 rpm. Find the cutting speed.
- V = π × 50 × 400/1000.
- = 62.8 m/min.
Answer: About 62.8 m/min
Example: What spindle speed gives 30 m/min on a 40 mm bar?
- N = 1000V/(πD) = 30 000/(π × 40).
- = 238.7 rpm.
Answer: About 240 rpm
Example: A 100 mm length is turned at 0.2 mm/rev and 400 rpm. How long does one cut take?
- Feed rate = 0.2 × 400 = 80 mm/min.
- Time = 100/80.
Answer: 1.25 minutes
Example: Find the compound-rest angle to turn a taper from 50 mm to 40 mm over 100 mm.
- tan α = (50 − 40)/(2 × 100) = 0.05.
- α = tan⁻¹ 0.05.
Answer: About 2.86°
A machine shop shapes metal by removing chips. Common machines are the lathe, drilling machine, shaper, milling machine and grinder. A lathe holds the work in a chuck and turns it against a tool held in a tool post. Operations include facing, turning, taper turning, knurling, thread cutting and parting. Cutting speed depends on material and diameter.
- Lathe parts: bed, headstock, tailstock, carriage and tool post.
- Coolant reduces heat and improves finish.
- Cutting speed v = πDN/1000 m/min, with D in mm.
- Never adjust a job while the spindle is rotating.
Practice questions
Turning reduces
- a job’s diameter
- its weight only
- its colour
- its hardness
Show the answer
Answer: A. a job’s diameter Definition.
Which lathe part holds the tool?
- tool post
- headstock
- bed
- chuck
Show the answer
Answer: A. tool post On the carriage.
Facing produces
- a flat end
- a thread
- a hole
- a groove only
Show the answer
Answer: A. a flat end Definition.
Knurling makes
- a rough gripping surface
- a hole
- a taper
- a weld
Show the answer
Answer: A. a rough gripping surface Definition.
Theory questions
Name the main parts of a lathe. (2 marks)
Show the model answer
Bed, headstock, tailstock, carriage (with the tool post) and feed mechanism.
Explain facing, turning, taper turning and thread cutting. Find the cutting speed for a 50 mm job at 300 rpm. (8 marks)
Show the model answer
Facing makes a flat end; turning reduces the diameter; taper turning gives a gradual change of diameter; thread cutting forms a helical groove using the lead screw. v = π × 50 × 300/1000 ≈ 47.1 m/min.
Blacksmithy shop
Topics: Forging tools and operations.
Forging in the smithy
Smithy (hand forging) shapes hot metal by hammering. Heated to a bright red or yellow heat in a forge, steel becomes soft enough to move under the hammer without cracking. Tools include the anvil, tongs to hold the work, hammers and sledges, and set tools such as swages, fullers and flatters.
Basic operations: drawing down lengthens and thins a bar, upsetting shortens and thickens it, bending, punching holes, cutting with a chisel, and forge welding. Because the volume of metal stays the same while it is shaped, the new size can be found by equating volumes.
Forging refines the grain and makes parts tough, which is why spanners, chisels and crankshafts are forged. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Tools: forge, anvil, tongs, hammers, swage, fuller, flatter
- Operations: drawing down, upsetting, bending, punching, cutting, forge welding
- Volume stays constant
- Forging improves grain and toughness
Example: A 20 mm square bar, 100 mm long, is drawn down to 10 mm square. How long does it become?
- Volume = 20 × 20 × 100 = 40 000 mm³.
- New length = 40 000/(10 × 10).
Answer: 400 mm
Example: A 25 mm round bar 80 mm long is upset to 40 mm diameter. Find the new length.
- Volume is constant, so length ∝ 1/d².
- 80 × (25/40)² = 80 × 0.390.
Answer: About 31 mm
Smithy shapes hot metal by hammering. A forge heats the metal, tongs hold it, and it is struck on an anvil using a hammer. Operations include upsetting, drawing out, bending, punching and swaging. Forging improves the grain structure, so forged parts are strong.
- Upsetting increases cross-section and reduces length.
- Drawing out does the opposite.
- Metal colour indicates its temperature.
- Stand clear of hot scale and wear protective gear.
Practice questions
Upsetting
- increases the cross-section
- decreases the cross-section
- cuts threads
- adds carbon
Show the answer
Answer: A. increases the cross-section Definition.
An anvil is used for
- supporting forging
- cutting wood
- measuring
- welding only
Show the answer
Answer: A. supporting forging Definition.
Forged parts are strong because of
- improved grain flow
- paint
- lower cost
- colour
Show the answer
Answer: A. improved grain flow Grain follows the shape.
Tongs are used to
- hold hot work
- cut metal
- measure
- polish
Show the answer
Answer: A. hold hot work Definition.
Theory questions
Name four forging operations. (2 marks)
Show the model answer
Upsetting, drawing out, bending and punching.
Describe the tools and safety rules of a smithy shop. (8 marks)
Show the model answer
Tools: forge, anvil, tongs, hammers, swages, fullers, and quenching tank. Safety: wear goggles, gloves and an apron, hold work firmly in suitable tongs, don’t touch hot pieces, keep the area clear and strike only when the metal is hot enough.
Electrical shop
Topics: Wiring, tools and safety.
House wiring in the shop
The electrical shop teaches safe wiring of lights, fans and sockets. Tools include combination pliers, screwdrivers, a wire stripper, a test lamp or tester, a multimeter and a drilling machine. Materials are PVC-insulated copper wires, switches, holders, sockets, ceiling roses, MCBs and fuses.
Basic circuits include a lamp controlled by one switch, two lamps in series and in parallel, a socket with its own switch, and staircase wiring, where two two-way switches let one lamp be turned on or off from either end. The switch always goes in the phase wire, never the neutral, so that the lamp holder is dead when switched off.
Every metal-bodied appliance must be earthed. Test a circuit before switching it on, and never work on a live circuit. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Switch in the phase wire
- Staircase wiring: two two-way switches
- Series: lamps share the voltage. Parallel: each gets full voltage
- Earth every metal body
- Test before switching on
Example: An energy meter read 4381 units last month and 4562 now. How many units were used, and the bill at ₹6 per unit?
- Units = 4562 − 4381 = 181.
- Cost = 181 × 6.
Answer: 181 units, ₹1086
Example: Two 230 V, 60 W lamps are joined in series across 230 V. Roughly what power does each give out (ignoring the change in filament resistance)?
- Each lamp’s resistance = 230²/60 = 881.7 Ω, so the current = 230/1763.3 = 0.13 A.
- Power each = 0.13² × 881.7 ≈ 15 W.
Answer: About 15 W each, so they glow dimly
The electrical shop teaches safe house wiring. Tools include pliers, screwdrivers, wire strippers, a tester and a multimeter. Wiring systems include batten, casing-capping and conduit. Components include switches, fuses, MCBs, sockets and earthing. Common circuits include staircase wiring, which uses two two-way switches to control one lamp.
- Switches go in the live wire.
- An MCB trips on overload and is reset rather than replaced.
- Earthing protects against shock.
- Switch the supply off before working.
- Colours: red or brown for live, black or blue for neutral, green for earth.
Practice questions
A switch is connected in the
- live wire
- neutral wire
- earth wire
- water pipe
Show the answer
Answer: A. live wire So that the load is dead when off.
An MCB protects against
- overcurrent
- rain
- noise
- dust
Show the answer
Answer: A. overcurrent It trips.
Earthing is for
- safety
- more current
- colour
- decoration
Show the answer
Answer: A. safety Fault current goes to earth.
Staircase wiring uses
- two two-way switches
- one fuse only
- one socket
- three lamps always
Show the answer
Answer: A. two two-way switches To control a lamp from two places.
Theory questions
Why is a switch placed in the live wire? (2 marks)
Show the model answer
So that when it is off, the appliance is disconnected from the supply, which is safer.
Draw and explain staircase wiring and list the safety rules of an electrical shop. (8 marks)
Show the model answer
Live goes to the common terminal of the first two-way switch, and two wires link the two switches. From the common terminal of the second switch, a wire goes to the lamp and on to neutral. Either switch can complete or break the circuit. Safety: switch off the supply, use insulated tools, wear rubber footwear, use correct fuses and never work with wet hands.
Pattern making shop
Topics: Pattern materials, types and allowances.
Patterns and their allowances
A pattern is a model of the part to be cast, used to make the cavity in the sand mould. Patterns are made of wood (cheap and easy for small numbers), metal (for long production runs), plastic or wax. Types include the solid (one-piece) pattern, the split pattern in two halves, the match-plate pattern and the loose-piece pattern.
A pattern is never exactly the size of the finished part. Metal shrinks as it cools, so a shrinkage allowance makes the pattern a little larger: roughly 1% for cast iron, and more for steel and aluminium (values vary between books). A machining allowance adds extra metal on surfaces that will be machined. A draft, a slight taper on vertical faces, lets the pattern be lifted out without breaking the mould.
Cores, made of sand, form holes and hollows in a casting; the pattern carries core prints to hold them in place. Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Materials: wood, metal, plastic, wax
- Types: solid, split, match-plate, loose-piece
- Shrinkage allowance (about 1% for cast iron)
- Machining allowance; draft; distortion allowance
- Core prints hold the cores
Example: A cast-iron part is to be 500 mm long. How long should the pattern be, with a 1% shrinkage allowance?
- Allowance = 1% of 500 = 5 mm.
- 500 + 5.
Answer: 505 mm
Example: The same face will also be machined, with 3 mm left for it. What is the pattern length now?
- Add the machining allowance to the size before shrinkage: 503 mm.
- Add 1% shrinkage: 503 × 1.01 ≈ 508 mm.
Answer: About 508 mm
A pattern is a replica of the casting used to form a cavity in sand. It is larger than the casting to allow for shrinkage, and it is usually made in wood. Allowances cover shrinkage, machining, draft, distortion and rapping. Types include single-piece, split, match-plate, loose-piece and sweep patterns.
- Draft is the taper that helps withdraw the pattern.
- Colour codes can mark surfaces to be machined.
- Split patterns suit complex shapes.
- Pattern wood should be seasoned and easy to work.
Practice questions
A pattern is
- a replica of a casting
- a molten metal
- a tool
- an electrode
Show the answer
Answer: A. a replica of a casting Definition.
Shrinkage allowance makes a pattern
- larger
- smaller
- the same
- hollow
Show the answer
Answer: A. larger Metal contracts on cooling.
Draft allowance helps
- withdraw the pattern
- pour metal
- cool the sand
- paint it
Show the answer
Answer: A. withdraw the pattern Taper on faces.
A common pattern material is
- wood
- glass
- water
- rubber band
Show the answer
Answer: A. wood Easy to shape.
Theory questions
Name the allowances given on a pattern. (3 marks)
Show the model answer
Shrinkage, machining, draft, distortion and rapping (shake) allowances.
Describe different types of patterns and allowances. (8 marks)
Show the model answer
Types: single-piece for simple work, split for complex shapes, match-plate for mass production, loose-piece for undercuts and sweep for symmetrical shapes. Allowances: shrinkage for contraction, machining for later finishing, draft for withdrawal, distortion for uneven cooling, and rapping for shaking loose.
Moulding shop
Topics: Sand, tools, moulding and defects.
Sand moulding and casting
In sand casting, a pattern is rammed in moulding sand inside a box called a flask (the upper part is the cope, the lower the drag). The pattern is removed, leaving a cavity, and molten metal is poured in through a pouring basin, sprue and runner, with a riser to feed the casting as it shrinks.
Green sand is silica sand mixed with a clay binder and water. Good moulding sand needs permeability (to let gases escape), strength (to hold its shape), refractoriness (to stand the heat), and collapsibility (to break away as the casting shrinks). Faults such as blow holes, cold shuts and misruns often trace back to the sand or the gating.
After cooling, the casting is shaken out, the gates and risers are cut off, and the surface is cleaned (fettled). Wear the protective gear the shop requires, keep tools sharp and in their place, and never use a machine you have not been shown.
- Flask: cope (top) and drag (bottom)
- Gating: pouring basin, sprue, runner, gate; riser
- Green sand: silica + clay + water
- Properties: permeability, strength, refractoriness, collapsibility
- Defects: blow holes, cold shut, misrun
Example: A cast-iron block is 200 × 100 × 50 mm. Find its mass (density 7200 kg/m³).
- Volume = 200 × 100 × 50 = 1 000 000 mm³ = 0.001 m³.
- Mass = 0.001 × 7200.
Answer: 7.2 kg
Example: A sand mix uses 100 kg of sand with 8% clay and 4% water (by weight of sand). How much of each?
- Clay = 0.08 × 100 = 8 kg.
- Water = 0.04 × 100 = 4 kg.
Answer: 8 kg clay and 4 kg water
Moulding makes a cavity in sand into which molten metal is poured. Moulding sand has silica, clay and moisture. Good sand must have strength, permeability, refractoriness and plasticity. A mould box has a cope and drag, with sprue, runner, gate and riser. Cores form hollow parts. Defects include blow holes, shrinkage and misruns.
- Permeability lets gases escape.
- A riser feeds metal as the casting shrinks.
- Ramming too hard reduces permeability.
- Wear protective clothing when pouring.
Practice questions
The top part of a moulding box is the
- cope
- drag
- cheek
- riser
Show the answer
Answer: A. cope Definition.
Permeability lets
- gases escape
- metal leak
- sand melt
- clay dissolve
Show the answer
Answer: A. gases escape Property of sand.
A core makes
- hollow parts
- external colour
- heat
- patterns
Show the answer
Answer: A. hollow parts Definition.
A riser
- feeds shrinkage
- cools sand
- holds the core only
- adds carbon
Show the answer
Answer: A. feeds shrinkage A reservoir of metal.
Theory questions
Name four properties of good moulding sand. (2 marks)
Show the model answer
Strength, permeability, refractoriness and plasticity.
Describe the steps of green sand moulding with a split pattern and name three casting defects. (8 marks)
Show the model answer
Place half the pattern in the drag, sieve and ram sand, and turn it over. Fit the cope and other half with a parting powder and ram again with the sprue pin in place. Vent the sand, separate the boxes, remove the pattern and cut the gate. Reassemble and pour. Defects: blow holes, shrinkage cavities and misruns.
Chapters follow the SCTE Assam syllabus. The notes and questions were written for this studio and are not official.