Light
Topics: Mirrors, refractive index, critical angle, total internal reflection, optical fibre; prism; lenses; telescope.
Mirrors and lenses
A plane mirror gives an upright image as far behind the mirror as the object is in front of it. A concave mirror converges light, and a convex mirror spreads it. Radius of curvature is twice the focal length. A lens works by refraction: a convex lens converges light to a focus, and a concave lens diverges it.
To find an image, follow two rays: one parallel to the axis, which passes through the focus after the lens, and one through the centre, which goes straight on. Watch the diagram as the object moves. Beyond 2F the image is real, inverted and smaller. Between F and 2F it is real, inverted and larger. Inside F, a convex lens gives an upright, enlarged, virtual image, which is how a magnifying glass works.
Use the Cartesian sign convention: measure from the pole or optical centre, with the direction of the incoming light as positive. An object usually has a negative u. A convex lens has a positive f and a concave mirror has a negative f.
- Mirror: 1/f = 1/v + 1/u
- Lens: 1/f = 1/v − 1/u
- Magnification (lens): m = v/u
- Power: P = 1/f, in dioptre, with f in metres
- Lenses in contact: P = P₁ + P₂
Example: An object is 30 cm from a concave mirror of focal length 15 cm. Find the image.
- With signs, u = −30 and f = −15.
- 1/v = 1/f − 1/u = −1/15 + 1/30 = −1/30.
- v = −30 cm, in front of the mirror.
Answer: 30 cm in front: real, inverted, the same size
Example: An object is 30 cm from a convex lens of focal length 20 cm. Find the image and magnification.
- With signs, u = −30 and f = +20.
- 1/v = 1/f + 1/u = 1/20 − 1/30 = 1/60.
- v = +60 cm.
- m = v/u = 60/(−30) = −2.
Answer: 60 cm on the far side: real, inverted, twice the size
Example: Lenses of +5 D and −2 D touch each other. Find the combined power and focal length.
- P = 5 + (−2) = +3 D.
- f = 1/P = 1/3 m.
Answer: +3 D and about 33.3 cm
Refraction, critical angle and optical fibres
Light bends when it enters another medium, since its speed changes. Going into a denser medium, it bends toward the normal. Snell’s law says that sin i/sin r is constant for a given pair of media, and this constant is the refractive index. n also equals the speed of light in vacuum divided by its speed in the medium.
Going from denser to rarer, light bends away from the normal. As the angle of incidence grows, the refracted ray moves closer to the surface. At the critical angle C it runs along the surface. Beyond this, no light leaves at all, and it all reflects back. This is total internal reflection, and it needs two conditions: denser to rarer, and i greater than C.
An optical fibre has a glass core with a higher refractive index, covered with cladding of a lower index. Light strikes the wall above the critical angle and bounces along by total internal reflection, with little loss, even around bends. Fibres are used for internet links and in endoscopes. Numerical aperture measures how much light a fibre can accept.
- n = sin i/sin r = c/v
- sin C = 1/n
- NA = √(n₁² − n₂²) = sin θ_max
Example: Light at 60° enters glass and refracts at 30°. Find the refractive index and the speed in the glass.
- n = sin 60°/sin 30° = 0.866/0.5 = 1.732.
- v = c/n = 3 × 10⁸/1.732.
Answer: n ≈ 1.73 and v ≈ 1.73 × 10⁸ m/s
Example: Find the critical angle for glass with n = 1.5.
- sin C = 1/n = 1/1.5 = 0.667.
- C = sin⁻¹(0.667).
Answer: About 41.8°
Example: A fibre has n₁ = 1.5 and n₂ = 1.46. Find the numerical aperture and the acceptance angle.
- NA = √(1.5² − 1.46²) = √(2.25 − 2.1316).
- = √0.1184 ≈ 0.344.
- θ = sin⁻¹(0.344).
Answer: NA ≈ 0.344 and about 20°
Prism and telescope
A prism bends light twice, and the angle between the incoming and outgoing rays is called the deviation. As the angle of incidence rises, the deviation falls to a minimum value D and then rises again. At minimum deviation, the ray passes symmetrically through the prism, and this gives a way to measure n. White light splits into colours, because each colour has its own refractive index.
An astronomical telescope has two convex lenses. The objective has a long focal length and forms a small real image of a distant object. The eyepiece has a short focal length and magnifies this image, like a magnifying glass. In normal adjustment, the final image is at infinity, and the tube length is the sum of the focal lengths.
- n = sin((A + D)/2)/sin(A/2)
- Telescope, normal adjustment: M = f₀/fₑ
- Tube length = f₀ + fₑ
Example: A prism with A = 60° has a minimum deviation of 30°. Find n.
- (A + D)/2 = 45°, and A/2 = 30°.
- n = sin 45°/sin 30°.
- = 0.707/0.5.
Answer: About 1.41
Example: A telescope has f₀ = 100 cm and fₑ = 5 cm. Find the magnifying power and the tube length.
- M = f₀/fₑ = 100/5.
- Length = 100 + 5.
Answer: 20 times and 105 cm
Light reflects from mirrors and refracts on entering another medium. Mirror and lens formulas locate images using a sign convention. Refractive index n = sin i/sin r. When light goes from a denser to a rarer medium above the critical angle, it reflects totally, which is how an optical fibre guides light along its core. A prism deviates light and a telescope uses lenses to enlarge distant objects.
- sin C = 1/n relates critical angle and refractive index.
- Power of a lens P = 1/f, with f in metres; the unit is the dioptre.
- A fibre has a core with a higher index than its cladding.
- At minimum deviation, n = sin((A + D)/2)/sin(A/2).
Key formulas
- 1/f = 1/v + 1/u (mirror)
- 1/f = 1/v − 1/u (lens)
- n = sin i/sin r
- sin C = 1/n
- NA = √(n₁² − n₂²)
- n = sin((A + D)/2)/sin(A/2)
- P = 1/f
Practice questions
Total internal reflection needs light to go from
- rarer to denser
- denser to rarer
- vacuum to glass
- air to water
Show the answer
Answer: B. denser to rarer And above the critical angle.
An optical fibre works on
- refraction only
- total internal reflection
- diffraction
- polarisation
Show the answer
Answer: B. total internal reflection Light stays in the core.
The unit of lens power is
- watt
- dioptre
- metre
- lumen
Show the answer
Answer: B. dioptre P = 1/f.
For glass with n = 1.5, sin C is
- 2/3
- 3/2
- 1/2
- 1
Show the answer
Answer: A. 2/3 1/n.
A convex lens of focal length 50 cm has power
- +2 D
- −2 D
- +0.5 D
- +50 D
Show the answer
Answer: A. +2 D 1/0.5.
An astronomical telescope’s magnifying power (normal) is
- f₀/fₑ
- fₑ/f₀
- f₀ + fₑ
- f₀fₑ
Show the answer
Answer: A. f₀/fₑ Objective over eyepiece.
Theory questions
Define critical angle and give its relation to refractive index. (2 marks)
Show the model answer
The angle of incidence in the denser medium for which the angle of refraction is 90°. sin C = 1/n.
An object is 30 cm from a convex lens of focal length 20 cm. Find the image position. (5 marks)
Show the model answer
1/v − 1/u = 1/f, with u = −30: 1/v = 1/20 − 1/30 = 1/60. v = +60 cm: a real image on the other side.
Explain the principle and structure of an optical fibre and find the numerical aperture for n₁ = 1.5 and n₂ = 1.46. (8 marks)
Show the model answer
Light enters a high-index core surrounded by lower-index cladding and travels by repeated total internal reflection. NA = √(1.5² − 1.46²) = √(2.25 − 2.1316) = √0.1184 ≈ 0.344. Fibres are used in communications and endoscopes.
Magnetism
Topics: Natural and artificial magnets; inverse square law; dipole fields; tangent law, deflection magnetometer; terrestrial magnetism.
Magnets and the inverse square law
Natural magnets such as lodestone occur in rock, and artificial ones are made from iron and its alloys. Every magnet has two poles. If you break a magnet, each piece has two poles, so an isolated pole has never been found. Like poles repel and unlike poles attract.
The force between two poles is proportional to the product of the pole strengths and inversely proportional to the square of the distance. Field lines leave the north pole and enter the south pole outside the magnet, and they form closed loops. They never cross, since a point cannot have two field directions.
A magnet in a uniform field feels a turning effect that tries to line it up with the field. A short magnet is a magnetic dipole with moment M. Its field at a distance d along its axis is twice its field at the same distance on the broad-side line.
- F = (μ₀/4π) m₁m₂/r², with μ₀/4π = 10⁻⁷
- τ = MB sin θ
- Short dipole, axial: B = (μ₀/4π) 2M/d³
- Short dipole, broad-side: B = (μ₀/4π) M/d³
- Tangent law: B = H tan θ
Example: Poles of 10 A m and 20 A m are 10 cm apart. Find the force.
- F = 10⁻⁷ × m₁m₂/r².
- = 10⁻⁷ × 200/(0.1)².
- = 10⁻⁷ × 20000.
Answer: 2 × 10⁻³ N
Example: A short magnet has M = 2 A m². Find its field 20 cm away on the axis and on the broad-side line.
- d³ = 0.2³ = 0.008.
- Axial: 10⁻⁷ × 2 × 2/0.008 = 5 × 10⁻⁵ T.
- Broad-side: half of this.
Answer: 5 × 10⁻⁵ T and 2.5 × 10⁻⁵ T
Example: Find the torque on a magnet with M = 2 A m² at 30° to a 0.5 T field.
- τ = MB sin θ.
- = 2 × 0.5 × sin 30°.
Answer: 0.5 N m
Example: A magnetometer needle deflects 60° where H = 3.2 × 10⁻⁵ T. Find the magnet’s field.
- The tangent law gives B = H tan θ.
- tan 60° = 1.732.
- B = 3.2 × 10⁻⁵ × 1.732.
Answer: About 5.5 × 10⁻⁵ T
Magnetic substances
Materials respond to a magnetic field in three ways. Diamagnetic materials such as bismuth and copper are weakly repelled, with a small negative susceptibility. Paramagnetic materials such as aluminium are weakly attracted, with a small positive susceptibility. Ferromagnetic materials such as iron, nickel and cobalt are strongly attracted, and they can keep their magnetism.
Soft iron magnetises easily and loses it easily, so it is used in transformer cores and electromagnets. Steel holds on to its magnetism, so it is used for permanent magnets. Heating a ferromagnet above its Curie temperature makes it paramagnetic.
- Diamagnetic: Bi, Cu
- Paramagnetic: Al
- Ferromagnetic: Fe, Ni, Co
The Earth as a magnet
A freely hanging compass settles nearly north-south, because the Earth behaves like a huge magnet. Three elements describe its field at any place. Declination is the angle between the geographic and the magnetic meridian. Dip is the angle that the field makes with the horizontal. The third is the horizontal component H.
A dip needle is horizontal at the magnetic equator and vertical at the magnetic poles. The total field B splits into a horizontal part and a vertical part. A compass responds to H, and that is why it does not work well near the magnetic poles.
- H = B cos δ
- V = B sin δ
- tan δ = V/H
- B² = H² + V²
Example: At a place where the dip is 60°, H = 0.3 G. Find the total field and the vertical part.
- B = H/cos δ = 0.3/0.5 = 0.6 G.
- V = B sin δ = 0.6 × 0.866.
Answer: B = 0.6 G and V ≈ 0.52 G
Like magnetic poles repel and unlike poles attract, with a force following an inverse square law. A dipole’s field is stronger on its end-on (axial) position than at the same distance broad-side on. Substances are diamagnetic, paramagnetic or ferromagnetic. The tangent law is used in a deflection magnetometer. The Earth behaves as a magnet described by three elements: declination, dip and the horizontal component.
- Magnetic field lines form closed loops and never cross.
- Ferromagnets such as iron are strongly attracted; diamagnets are weakly repelled.
- Tangent law: B = H tan θ.
- At the magnetic poles dip is 90°, and at the equator it is 0°.
- H = B cos δ, V = B sin δ.
Key formulas
- F = (μ₀/4π) m₁m₂/r²
- B_axial = (μ₀/4π) 2Md/(d² − l²)²
- τ = MB sin θ
- B = H tan θ
Practice questions
Iron is
- diamagnetic
- paramagnetic
- ferromagnetic
- non-magnetic
Show the answer
Answer: C. ferromagnetic Strongly magnetised.
Dip at the magnetic equator is
- 0°
- 45°
- 90°
- 180°
Show the answer
Answer: A. 0° The needle is horizontal.
Field lines of a magnet
- cross each other
- form closed loops
- are straight only
- start and end in air
Show the answer
Answer: B. form closed loops No isolated poles.
Torque on a magnet in a field is
- MB sin θ
- MB cos θ
- MB
- M/B
Show the answer
Answer: A. MB sin θ τ = MB sin θ.
The angle between geographic and magnetic meridians is
- dip
- declination
- inclination
- tangent
Show the answer
Answer: B. declination Definition.
Theory questions
Name the elements of terrestrial magnetism. (2 marks)
Show the model answer
Declination, dip (inclination) and the horizontal component of Earth’s field.
Dip at a place is 60° and H is 0.3 G. Find the total field. (3 marks)
Show the model answer
B = H/cos δ = 0.3/0.5 = 0.6 G.
Compare diamagnetic, paramagnetic and ferromagnetic substances with examples. (8 marks)
Show the model answer
Diamagnetic: weakly repelled, small negative susceptibility, such as bismuth and copper. Paramagnetic: weakly attracted, small positive susceptibility, such as aluminium. Ferromagnetic: strongly attracted, large susceptibility and retained magnetism, such as iron, nickel and cobalt.
Electrostatics
Topics: Charge, Coulomb’s law, field, lines of force; potential; capacitors and combinations.
Charge, Coulomb’s law and the field
Rubbing a plastic comb moves electrons between the comb and the hair. A body with extra electrons is negative, and one short of electrons is positive. Charge is conserved, and it comes in whole numbers of the electronic charge, 1.6 × 10⁻¹⁹ C. Like charges repel and unlike charges attract.
Coulomb’s law gives the force between point charges: proportional to the product of the charges and inversely proportional to the square of the distance. Double the distance, and the force falls to a quarter. A medium with dielectric constant K reduces the force K times.
The electric field at a point is the force on a unit positive charge placed there. Lines of force show its direction. They start on positive charges, end on negative ones and never cross. They are closest where the field is strongest.
- F = kq₁q₂/r², with k = 9 × 10⁹ N m²/C²
- E = F/q = kq/r², in N/C
- Force on a charge: F = qE
Example: Charges of 1 μC and 2 μC are 10 cm apart. Find the force.
- F = 9 × 10⁹ × (1 × 10⁻⁶)(2 × 10⁻⁶)/(0.1)².
- Numerator: 9 × 10⁹ × 2 × 10⁻¹² = 0.018.
- F = 0.018/0.01.
Answer: 1.8 N, repelling
Example: Find the field 20 cm from a 4 nC charge.
- E = kq/r².
- = 9 × 10⁹ × 4 × 10⁻⁹/(0.2)².
- = 36/0.04.
Answer: 900 N/C
Electric potential
Potential at a point is the work done in bringing a unit positive charge from infinity to that point. It is a scalar, so potentials from several charges simply add. Positive charge moves naturally from higher potential to lower potential, just as water flows downhill. Potential difference is measured in volts, and 1 V = 1 J/C.
Field and potential are connected: the field is the rate at which potential falls with distance. Between two parallel plates, the field is uniform, and E = V/d.
- V = kq/r
- Work: W = qV
- E = −dV/dx; in a uniform field E = V/d
Example: Find the potential 20 cm from a 4 nC charge, and the work to bring a 2 μC charge there from far away.
- V = kq/r = 9 × 10⁹ × 4 × 10⁻⁹/0.2 = 180 V.
- W = qV = 2 × 10⁻⁶ × 180.
Answer: 180 V and 3.6 × 10⁻⁴ J
Capacitors
A capacitor stores charge on two conducting plates separated by an insulator. Connected to a battery, it charges until its voltage matches the battery. The charge is proportional to the voltage, and the constant is the capacitance, measured in farads. A farad is very large, so μF and pF are common.
Bigger plates and a smaller gap give a larger capacitance. A dielectric between the plates raises it K times. Capacitors in parallel share the voltage, and their capacitances add. In series they carry the same charge, and their reciprocals add, so the total is less than the smallest one. The stored energy is released quickly on discharge, as in a camera flash.
- C = Q/V
- C = Kε₀A/d
- Parallel: C = C₁ + C₂
- Series: 1/C = 1/C₁ + 1/C₂
- U = ½CV²
Example: Plates of area 0.1 m² are 1 mm apart with air between them. Find C, and then C with a dielectric of K = 5.
- C = ε₀A/d = 8.85 × 10⁻¹² × 0.1/10⁻³.
- = 8.85 × 10⁻¹⁰ F = 885 pF.
- With the dielectric: 5 × 885 pF.
Answer: 885 pF and 4425 pF
Example: 3 μF and 6 μF in series are connected to 12 V. Find the total capacitance, the charge and each voltage.
- 1/C = 1/3 + 1/6 = 1/2, so C = 2 μF.
- Q = CV = 2 × 12 = 24 μC on each.
- V₁ = 24/3 = 8 V and V₂ = 24/6 = 4 V, which add to 12 V.
Answer: 2 μF, 24 μC, 8 V and 4 V
Example: Find the energy in a 10 μF capacitor at 100 V.
- U = ½CV².
- = ½ × 10⁻⁵ × 100².
- = ½ × 10⁻⁵ × 10⁴.
Answer: 0.05 J
Charge comes from an excess or shortage of electrons. Coulomb’s law gives the force between charges, and the electric field is the force per unit positive charge. Potential is work per unit charge. A capacitor stores charge, and its capacitance depends on plate area, separation and the dielectric between the plates. Capacitors in parallel add directly, and in series their reciprocals add.
- Field lines start on positive and end on negative charges and never cross.
- A dielectric of constant K multiplies capacitance by K.
- Gauss’s law links flux through a closed surface to the charge inside.
- E = −dV/dx links field and potential.
Key formulas
- F = kq₁q₂/r², k = 9 × 10⁹
- E = F/q = kq/r²
- V = kq/r
- C = Q/V
- C = Kε₀A/d
- C_p = C₁ + C₂
- 1/C_s = 1/C₁ + 1/C₂
- U = ½CV²
Practice questions
The SI unit of charge is
- ampere
- coulomb
- volt
- farad
Show the answer
Answer: B. coulomb Definition.
If distance doubles, Coulomb force becomes
- double
- half
- one quarter
- four times
Show the answer
Answer: C. one quarter Inverse square law.
Capacitance is measured in
- henry
- farad
- ohm
- tesla
Show the answer
Answer: B. farad C = Q/V.
A dielectric makes capacitance
- fall
- rise
- zero
- unchanged
Show the answer
Answer: B. rise C ∝ K.
Two 6 μF capacitors in series give
- 12 μF
- 6 μF
- 3 μF
- 36 μF
Show the answer
Answer: C. 3 μF 1/C = 1/6 + 1/6.
Electric field lines
- cross each other
- form loops in electrostatics
- start on + and end on −
- are always circular
Show the answer
Answer: C. start on + and end on − Property.
Theory questions
State Coulomb’s law. (2 marks)
Show the model answer
The force between two point charges is proportional to the product of the charges and inversely to the square of the distance between them.
Find the equivalent of 2 μF and 3 μF in series, and in parallel. (3 marks)
Show the model answer
Series: 6/5 = 1.2 μF. Parallel: 5 μF.
Derive the relation for capacitors in series and find the charge on each when 3 μF and 6 μF in series are connected to 12 V. (8 marks)
Show the model answer
In series the charge is the same and V = V₁ + V₂ = Q/C₁ + Q/C₂, so 1/C = 1/C₁ + 1/C₂. Here C = 2 μF and Q = CV = 24 μC on each.
Current electricity
Topics: Voltaic cell and its defects; Leclanché, Daniell and dry cells; primary and secondary cells, grouping; Ohm’s law, Kirchhoff’s laws, bridge.
Current, Ohm’s law and resistance
Current is the rate of flow of charge. Metals conduct because they have free electrons that drift when a potential difference is applied. Conventional current is taken from positive to negative, which is opposite to the electrons’ movement. One ampere means one coulomb passing every second.
Ohm’s law says that the current in a conductor is proportional to the potential difference across it, as long as temperature and other conditions stay the same. The ratio V/I is the resistance. It depends on the length, the area and the material: a long, thin wire resists more. Resistivity ρ is a property of the material. In metals, resistance rises with temperature, because the atoms vibrate more and obstruct the electrons.
- I = q/t
- V = IR
- R = ρL/A
- R_t = R₀(1 + αt)
- Series: R = R₁ + R₂ + …
- Parallel: 1/R = 1/R₁ + 1/R₂ + …
Example: Find the resistance of a copper wire 100 m long with an area of 1 mm², where ρ = 1.7 × 10⁻⁸ Ω m.
- A = 10⁻⁶ m².
- R = ρL/A = 1.7 × 10⁻⁸ × 100/10⁻⁶.
Answer: 1.7 Ω
Example: A coil has 10 Ω at 0 °C and α = 0.004 per °C. Find its resistance at 100 °C.
- R = R₀(1 + αt).
- = 10 × (1 + 0.004 × 100).
- = 10 × 1.4.
Answer: 14 Ω
Example: 2 Ω, 3 Ω and 6 Ω in parallel are in series with 4 Ω, across 10 V. Find the current from the source.
- Parallel part: 1/R = 1/2 + 1/3 + 1/6 = 1, so R = 1 Ω.
- Total: 1 + 4 = 5 Ω.
- I = 10/5.
Answer: 2 A
Cells, emf and internal resistance
A cell turns chemical energy into electrical energy. Its emf is the energy it gives to each coulomb, measured when no current flows. When current does flow, some voltage is lost inside the cell because of its internal resistance, so the terminal voltage is less than the emf.
Cells in series add their emfs, which suits a load that needs a higher voltage. Equal cells in parallel keep the same emf, but their internal resistance falls, which suits a load that needs a larger current. A primary cell, such as a dry cell, cannot be recharged. A secondary cell, such as a lead-acid battery, can be.
- I = E/(R + r)
- V = E − Ir
- n in series: I = nE/(R + nr)
- n equal in parallel: I = E/(R + r/n)
Example: A 12 V cell with r = 1 Ω feeds a 5 Ω resistor. Find the current and terminal voltage.
- I = E/(R + r) = 12/6 = 2 A.
- V = E − Ir = 12 − 2 × 1.
Answer: 2 A and 10 V
Example: Six 1.5 V cells, each with r = 0.5 Ω, are in series with a 6 Ω load. Find the current.
- Total emf = 6 × 1.5 = 9 V.
- Total internal resistance = 6 × 0.5 = 3 Ω.
- I = 9/(6 + 3).
Answer: 1 A
Example: Three 1.5 V cells, each with r = 0.6 Ω, are in parallel with a 2.8 Ω load. Find the current.
- The emf stays 1.5 V.
- r/n = 0.6/3 = 0.2 Ω.
- I = 1.5/(2.8 + 0.2).
Answer: 0.5 A
Voltaic cell and its defects
A simple voltaic cell has a zinc plate and a copper plate in dilute sulphuric acid, and gives about 1 V. It has two defects. In local action, impurities in the zinc form tiny cells on the plate, so zinc dissolves even when no current is taken. It is reduced by coating the zinc with mercury, which is called amalgamating. In polarisation, hydrogen bubbles collect on the copper plate. These raise the internal resistance and set up an opposing emf, and the current falls off.
Polarisation is cured by a depolariser, a chemical that removes the hydrogen. The Daniell cell uses copper sulphate solution and gives about 1.1 V. The Leclanché cell uses manganese dioxide with a zinc rod in ammonium chloride, and gives about 1.5 V. A dry cell is a Leclanché cell with the electrolyte as a paste, so it can be carried anywhere.
Storage cells are secondary cells. A lead-acid cell gives about 2 V and uses lead plates in sulphuric acid. An Edison cell uses nickel and iron plates in alkali, and is lighter and more robust, but gives a lower voltage per cell.
- Local action: cure by amalgamating the zinc
- Polarisation: cure with a depolariser
- Daniell depolariser: CuSO₄
- Leclanché depolariser: MnO₂
Kirchhoff’s laws and the Wheatstone bridge
Kirchhoff’s current law says the currents entering a junction equal the currents leaving it, because charge does not pile up anywhere. His voltage law says that around any closed loop, the sum of the emfs equals the sum of the IR drops, because energy is conserved. Take a direction for each current. If the answer is negative, the current runs the opposite way.
The Wheatstone bridge has four resistors with a galvanometer across the middle. Adjust one resistor until the galvanometer reads zero. Then the two midpoints are at the same potential, and the ratio of the resistors on one side equals that on the other. This allows an unknown resistance to be measured very accurately, without knowing the current or the supply voltage.
- ΣI = 0 at a junction
- ΣE = ΣIR around a loop
- Balance: P/Q = R/S
Example: A 12 V and a 9 V cell push currents I₁ and I₂ through separate 2 Ω resistors, and the two currents join to flow through a shared 2 Ω resistor. Find the currents.
- The shared resistor carries I₁ + I₂.
- Loop 1: 12 = 2I₁ + 2(I₁ + I₂), so 2I₁ + I₂ = 6.
- Loop 2: 9 = 2I₂ + 2(I₁ + I₂), so 2I₁ + 4I₂ = 9.
- Subtract: 3I₂ = 3, so I₂ = 1 A.
- Then 2I₁ = 5, so I₁ = 2.5 A. Check loop 1: 5 + 7 = 12.
Answer: I₁ = 2.5 A, I₂ = 1 A, and 3.5 A through the shared resistor
Example: A bridge balances with P = 10 Ω, Q = 20 Ω and R = 30 Ω. Find S.
- P/Q = R/S.
- 10/20 = 30/S.
- S = 30 × 20/10.
Answer: 60 Ω
Current is the rate of flow of charge, driven by a potential difference. Ohm’s law says V = IR at a constant temperature. Resistance depends on length, area and material, and usually rises with temperature in metals. Kirchhoff’s laws solve networks: the current law expresses charge conservation and the voltage law expresses energy conservation. A cell’s emf exceeds its terminal voltage because of internal resistance, and the balanced Wheatstone bridge finds an unknown resistance.
- Series: R = R₁ + R₂; parallel: 1/R = 1/R₁ + 1/R₂.
- Bridge balance: P/Q = R/S.
- Cells in series add emf; cells in parallel add capacity at the same emf.
- A primary cell cannot be recharged; a secondary cell can.
- Joule’s law: heat H = I²Rt.
- A simple voltaic cell suffers from local action and polarisation; the Leclanché, Daniell and dry cells reduce these defects.
- Lead and Edison cells are the common storage cells.
Key formulas
- V = IR
- R = ρL/A
- R_t = R₀(1 + αt)
- I = E/(R + r)
- P = VI = I²R
- H = I²Rt
Practice questions
The SI unit of resistance is
- volt
- ampere
- ohm
- watt
Show the answer
Answer: C. ohm R = V/I.
Doubling a wire’s length makes its resistance
- half
- double
- four times
- the same
Show the answer
Answer: B. double R ∝ L.
Kirchhoff’s current law is based on conservation of
- energy
- charge
- momentum
- mass
Show the answer
Answer: B. charge Nothing accumulates at a node.
Two 4 Ω resistors in parallel give
- 8 Ω
- 4 Ω
- 2 Ω
- 1 Ω
Show the answer
Answer: C. 2 Ω 4/2.
A dry cell is a
- secondary cell
- primary cell
- fuel cell
- solar cell
Show the answer
Answer: B. primary cell Not rechargeable.
Power in a 10 Ω resistor with 2 A is
- 20 W
- 40 W
- 5 W
- 200 W
Show the answer
Answer: B. 40 W I²R.
Polarisation in a simple cell is caused by
- hydrogen bubbles on the copper plate
- zinc impurities
- too much acid
- heat
Show the answer
Answer: A. hydrogen bubbles on the copper plate The gas layer raises internal resistance.
Theory questions
Distinguish between emf and potential difference. (3 marks)
Show the model answer
Emf is the energy per unit charge given by a source, measured when no current flows. Potential difference is the energy per unit charge used between two points. V = E − Ir.
A 12 V cell with r = 1 Ω feeds a 5 Ω resistor. Find the current and terminal voltage. (3 marks)
Show the model answer
I = 12/6 = 2 A. V = E − Ir = 10 V.
State Kirchhoff’s laws and derive the balance condition of a Wheatstone bridge. (8 marks)
Show the model answer
KCL: the sum of currents at a junction is zero. KVL: the sum of emfs and voltage drops round a loop is zero. With no galvanometer current, I₁ flows through P and Q and I₂ through R and S. The midpoints are at equal potential, so I₁P = I₂R and I₁Q = I₂S. Dividing gives P/Q = R/S.
Effects of current
Topics: Joule’s law, power, electrolysis, Faraday’s law and plating.
Heating effect and energy bills
Joule’s law says that heat produced is proportional to the square of the current, the resistance and the time. Doubling the current gives four times the heat. A heater element uses an alloy such as nichrome, with high resistance and a high melting point. A fuse wire has a low melting point and is connected in series, so it melts and breaks the circuit when too much current flows.
Electricity boards charge for energy. One unit is one kilowatt-hour, the energy used by a 1 kW device in an hour. To choose a fuse, find the current from I = P/V and use a rating a little above it.
- H = I²Rt
- P = VI
- Units = kW × hours
- 1 unit = 3.6 × 10⁶ J
Example: A 1000 W heater runs for 5 hours a day for 30 days, at ₹6 per unit. Find the cost.
- Units = 1 × 5 × 30 = 150.
- Cost = 150 × 6.
Answer: ₹900
Example: A 1000 W kettle heats 2 kg of water from 20 °C to 100 °C, with c = 4200 J/kg K. How long does it take if no heat is lost?
- Q = mcΔT = 2 × 4200 × 80 = 672000 J.
- t = Q/P = 672000/1000 = 672 s.
Answer: 672 s, about 11.2 minutes
Example: An appliance takes 1100 W from a 220 V supply. What current does it draw?
- I = P/V.
- = 1100/220.
Answer: 5 A, so its fuse needs a rating a little above this
Chemical effect and electrolysis
Acids, bases and salts in water contain ions that carry current. Passing a current through such a liquid breaks it down, which is electrolysis. Positive ions move to the cathode, and negative ions move to the anode. In electroplating the object is the cathode, the coating metal is the anode, and the electrolyte is a salt of that metal.
Faraday’s first law says that the mass deposited is proportional to the charge passed. Z is the electrochemical equivalent, the mass deposited per coulomb. His second law says that for the same charge, the masses of different substances are in the ratio of their chemical equivalents.
- m = ZIt
- m₁/m₂ = E₁/E₂
- Copper: Z ≈ 3.29 × 10⁻⁷ kg/C
Example: A current of 2 A passes through copper sulphate solution for 30 minutes. Find the mass of copper deposited.
- t = 30 × 60 = 1800 s.
- Charge = 2 × 1800 = 3600 C.
- m = 3.29 × 10⁻⁷ × 3600 ≈ 1.18 × 10⁻³ kg.
Answer: About 1.18 g
Example: The same charge deposits 1.08 g of silver and some copper. Equivalents are 108 for silver and 31.75 for copper. Find the mass of copper.
- m_Cu/m_Ag = E_Cu/E_Ag.
- m_Cu = 1.08 × 31.75/108.
Answer: 0.3175 g
A current produces heat, chemical and magnetic effects. Joule’s law gives the heat in a resistor, which is used in heaters and fuses. Electrical energy is billed in kilowatt-hours. A current through an electrolyte decomposes it, and Faraday’s laws of electrolysis relate the mass deposited to the charge passed. This is used in electroplating.
- A fuse has a low melting point and is connected in series.
- 1 kWh = 1 unit = 3.6 × 10⁶ J.
- A heater element has a high resistance and a high melting point.
- A copper voltameter measures charge by the mass deposited.
Key formulas
- H = I²Rt
- P = VI
- m = ZIt
Practice questions
Joule’s law gives H proportional to
- I
- I²
- 1/I
- nothing
Show the answer
Answer: B. I² H = I²Rt.
A 1 kW heater used for 2 h consumes
- 1 unit
- 2 units
- 0.5 unit
- 20 units
Show the answer
Answer: B. 2 units kW × h.
A fuse is connected
- in parallel
- in series
- to earth only
- after the load only
Show the answer
Answer: B. in series It must carry all the current.
In electroplating the object is the
- anode
- cathode
- electrolyte
- battery
Show the answer
Answer: B. cathode Metal ions deposit on it.
Faraday’s first law: m is proportional to
- charge
- voltage
- time only
- density
Show the answer
Answer: A. charge m = Zq.
Theory questions
State Joule’s law of heating. (2 marks)
Show the model answer
Heat produced is proportional to the square of the current, the resistance and the time: H = I²Rt.
A 1000 W, 220 V heater runs 5 h a day for 30 days. Find the units used and the cost at ₹6 per unit. (5 marks)
Show the model answer
Energy = 1 × 5 × 30 = 150 units. Cost = ₹900.
Electromagnetism
Topics: Magnetic effect; Fleming’s rules; force between conductors; induction; transformer.
The magnetic effect of current
Oersted found that a current deflects a compass, so a current produces a magnetic field. Around a straight wire, the field lines are circles. The right-hand thumb rule gives the direction: point the thumb along the current, and the fingers curl in the direction of the field. Winding the wire into a coil strengthens the field.
- Straight wire: B = μ₀I/(2πr)
- Centre of a coil: B = μ₀NI/(2r)
- μ₀ = 4π × 10⁻⁷ T m/A
Example: Find the field 5 cm from a long wire carrying 10 A.
- B = μ₀I/(2πr) = (4π × 10⁻⁷ × 10)/(2π × 0.05).
- This simplifies to 2 × 10⁻⁷ × 10/0.05.
Answer: 4 × 10⁻⁵ T
Example: A coil of 100 turns and radius 10 cm carries 1 A. Find the field at its centre.
- B = μ₀NI/(2r).
- = 4π × 10⁻⁷ × 100 × 1/(2 × 0.1).
- = 2π × 10⁻⁴.
Answer: About 6.28 × 10⁻⁴ T
Force on a charge and on a conductor
A charge moving in a magnetic field feels a force at right angles to both its velocity and the field. Because this force is sideways, it changes the direction and not the speed. A current is many moving charges, so a wire carrying current also feels a force. This is how an electric motor works.
Fleming’s left-hand rule gives the direction. Hold the thumb, first finger and second finger at right angles. The first finger points along the field, the second along the current, and the thumb gives the motion. Two parallel wires with current in the same direction attract each other, and with opposite currents they repel.
- F = qvB sin θ
- F = BIL sin θ
- Parallel wires: F/L = μ₀I₁I₂/(2πd)
Example: An electron at 10⁶ m/s moves at right angles to a 0.5 T field. Find the force.
- F = qvB sin 90°.
- = 1.6 × 10⁻¹⁹ × 10⁶ × 0.5.
Answer: 8 × 10⁻¹⁴ N
Example: A 20 cm wire carrying 4 A lies at right angles to a 0.5 T field. Find the force.
- F = BIL.
- = 0.5 × 4 × 0.2.
Answer: 0.4 N
Example: Parallel wires 10 cm apart carry 10 A and 20 A in the same direction. Find the force per metre.
- F/L = 2 × 10⁻⁷ × I₁I₂/d.
- = 2 × 10⁻⁷ × 200/0.1.
Answer: 4 × 10⁻⁴ N/m, attracting
Electromagnetic induction
Faraday found the reverse effect: a changing magnetic flux through a coil produces an emf, and the emf lasts only while the flux is changing. Move a magnet toward a coil and the meter deflects. Hold it still and the reading drops to zero. Move it away and the meter deflects the other way. The faster the change and the more turns in the coil, the larger the emf.
Lenz’s law gives the direction: the induced current opposes the change that causes it. Push a north pole in, and the coil’s near face becomes north and pushes back. So you must do work against it, and this work becomes electrical energy. This is why Lenz’s law is a form of energy conservation. For a wire moving through a field, Fleming’s right-hand rule gives the direction of the current.
- Φ = BA cos θ, in weber
- e = −N dΦ/dt
- Moving wire: e = BLv
Example: The flux through a coil of 100 turns changes by 0.02 Wb in 0.1 s. Find the emf.
- e = N ΔΦ/Δt.
- = 100 × 0.02/0.1.
Answer: 20 V
Example: A 20 cm wire moves at 10 m/s at right angles to a 0.5 T field. Find the emf.
- e = BLv.
- = 0.5 × 0.2 × 10.
Answer: 1 V
Transformers and long-distance transmission
A transformer has two coils on an iron core. Alternating current in the primary creates a changing flux in the core, and this flux induces an emf in the secondary. It works only with AC, since a steady DC gives no change in flux. A step-up transformer has more secondary turns, and a step-down one has fewer. If the voltage goes up, the current comes down, because power cannot increase.
Real transformers have copper losses in the windings, eddy-current and hysteresis losses in the core, and some flux leakage. A laminated soft iron core reduces the core losses.
Power stations send electricity at very high voltage. For a given power, a higher voltage means a smaller current, and the heat lost in the lines is I²R. Ten times the voltage gives a tenth of the current and only a hundredth of the loss. Transformers near homes then step it down to a safe voltage.
- V₂/V₁ = N₂/N₁
- Ideal: V₁I₁ = V₂I₂
- η = output power/input power
- Line loss = I²R
Example: A transformer has 200 primary and 1000 secondary turns, with 230 V input. Find the output voltage, and the primary current if the secondary gives 1 A (ideal).
- V₂ = 230 × 1000/200 = 1150 V.
- V₁I₁ = V₂I₂, so I₁ = 1150 × 1/230.
Answer: 1150 V and 5 A
Example: 100 kW is sent through a line of 1 Ω. Compare the loss at 1 kV and at 10 kV.
- At 1 kV: I = 100000/1000 = 100 A, and the loss = 100² × 1 = 10 kW.
- At 10 kV: I = 10 A, and the loss = 10² × 1 = 100 W.
Answer: 10 kW against 0.1 kW: a hundred times less
A current produces a magnetic field whose direction follows the right-hand thumb rule. A charge moving in a field feels a force, and a current-carrying conductor feels a force given by Fleming’s left-hand rule. Faraday’s law says a changing flux induces an emf, and Lenz’s law says it opposes the change. A transformer uses mutual induction to change AC voltage, which lets power travel long distances with low losses.
- Parallel currents in the same direction attract each other.
- Fleming’s right-hand rule gives induced current direction.
- A transformer works only on AC.
- High-voltage transmission means low current and low I²R loss.
- Losses: copper, iron (eddy, hysteresis), flux leakage.
Key formulas
- F = qvB sin θ
- F = BIL sin θ
- e = −N dΦ/dt
- B = μ₀I/(2πr)
- V₂/V₁ = N₂/N₁ = I₁/I₂
Practice questions
Lenz’s law is based on conservation of
- charge
- energy
- mass
- momentum
Show the answer
Answer: B. energy The induced effect opposes the cause.
A transformer works on
- DC
- AC
- both equally
- batteries
Show the answer
Answer: B. AC It needs changing flux.
Fleming’s left-hand rule gives
- induced emf
- the force on a conductor
- resistance
- capacitance
Show the answer
Answer: B. the force on a conductor Motor rule.
A step-up transformer has
- N₂ > N₁
- N₂ < N₁
- N₂ = N₁
- no core
Show the answer
Answer: A. N₂ > N₁ More turns on the secondary.
Long-distance power is sent at
- low voltage
- high voltage
- zero current
- DC only
Show the answer
Answer: B. high voltage Reduces I²R loss.
The unit of magnetic field is
- weber
- tesla
- henry
- farad
Show the answer
Answer: B. tesla B in tesla.
Theory questions
State Faraday’s laws of electromagnetic induction. (3 marks)
Show the model answer
A changing flux linked with a coil induces an emf, which lasts as long as the change does. Its magnitude is proportional to the rate of change of flux linkage.
A transformer has 200 primary and 1000 secondary turns. With 230 V input, find the output voltage. (3 marks)
Show the model answer
V₂ = 230 × 1000/200 = 1150 V.
Explain the principle and losses of a transformer and why AC power is transmitted at high voltage. (8 marks)
Show the model answer
An alternating primary current sets up a changing flux in the core, which induces an emf in the secondary by mutual induction. Losses: copper, eddy current, hysteresis and flux leakage. For a given power P = VI, higher V means lower I, so the I²R line loss falls greatly.
Modern physics
Topics: Photoelectric equation and cells; mass defect; X-rays; radioactivity; lasers.
Quanta and the photoelectric effect
Planck proposed that light energy comes in packets, called quanta or photons, each with an energy E = hf. A convenient form is E in eV ≈ 1240/λ, with λ in nm. Blue light has more energy per photon than red.
When light of a suitable frequency falls on a clean metal, electrons are ejected. The wave picture of light cannot explain the results. Below a threshold frequency, no electrons leave, however bright the light. Above it, electrons leave immediately. Their greatest kinetic energy depends on the frequency, not the brightness. Brighter light gives more electrons, and so a larger current, without giving them more energy.
Einstein explained this using photons. One photon gives all its energy to one electron. Part of it, the work function φ, frees the electron from the metal, and the rest becomes kinetic energy.
- E = hf = hc/λ, with h = 6.63 × 10⁻³⁴ J s
- hf = φ + ½mv²
- Threshold: hf₀ = φ
- Stopping potential: eV₀ = ½mv²
Example: Find the energy of a 620 nm photon, in eV.
- E ≈ 1240/λ.
- = 1240/620.
Answer: 2 eV
Example: A metal has φ = 2 eV, and photons of 5 eV fall on it. Find the greatest KE and the stopping potential.
- KE = hf − φ = 5 − 2 = 3 eV.
- The stopping potential in volts equals the KE in eV.
Answer: 3 eV and 3 V
Example: Find the threshold wavelength for a metal with φ = 2.3 eV.
- At the threshold, E = φ.
- λ₀ ≈ 1240/2.3.
Answer: About 539 nm
Radioactivity and the nucleus
Some heavy nuclei are unstable and decay on their own, unaffected by temperature or pressure. Alpha particles are helium nuclei: they are heavy, ionise strongly and are stopped by paper. Beta particles are fast electrons. Gamma rays are high-energy electromagnetic waves with no charge, and they penetrate the most.
Half-life is the time for half of the nuclei to decay. It is constant for each isotope. Alpha emission reduces the mass number by 4 and the atomic number by 2. Beta emission keeps the mass number the same and raises the atomic number by 1.
A nucleus has less mass than its separate protons and neutrons. The difference, called the mass defect, is the binding energy, given by E = mc². Splitting a heavy nucleus (fission) or joining light nuclei (fusion) gives more tightly bound products and releases energy. Nuclear reactors use controlled fission, and the Sun runs on fusion.
- After n half-lives: N = N₀/2ⁿ
- E = mc²
- 1 u = 931 MeV
Example: A 16 g sample has a half-life of 5 days. How much remains after 15 days?
- Number of half-lives: 15/5 = 3.
- N = 16/2³ = 16/8.
Answer: 2 g
Example: A helium nucleus has a mass of 4.00151 u. A proton is 1.00728 u, and a neutron is 1.00866 u. Find the binding energy.
- Parts: 2(1.00728) + 2(1.00866) = 4.03188 u.
- Mass defect: 4.03188 − 4.00151 = 0.03037 u.
- Energy: 0.03037 × 931 ≈ 28.3 MeV.
- Per nucleon: 28.3/4 ≈ 7.07 MeV.
Answer: About 28.3 MeV, or 7.07 MeV per nucleon
X-rays
X-rays are electromagnetic waves of very short wavelength. They are produced when fast electrons, accelerated by a high voltage in a Coolidge tube, strike a metal target. Most of the energy becomes heat, so the target needs a high melting point. The shortest wavelength occurs when an electron gives all its energy to one photon, and so it depends on the tube voltage.
X-rays pass through soft tissue but are absorbed more by bone, which is why they are used in medical imaging. Other uses include finding flaws in metal castings and studying crystal structure. Too much exposure is harmful, so operators use lead shielding.
- eV = hc/λ_min
- λ_min (Å) ≈ 12400/V
Example: Find the shortest wavelength from an X-ray tube at 40 kV.
- λ_min ≈ 12400/V.
- = 12400/40000.
Answer: About 0.31 Å
Lasers
LASER stands for Light Amplification by Stimulated Emission of Radiation. An atom in a higher level can drop down by itself at a random moment, which is spontaneous emission. However, a passing photon of the right energy can trigger the drop, and the new photon is an exact copy of the first. This is stimulated emission.
Normally most atoms are in the lower level, so photons get absorbed more often than copied. Pumping lifts atoms into a metastable level where they stay for a long time, until more atoms are up than down. This is population inversion. Mirrors at the ends send the light back and forth, building a strong beam.
Laser light is monochromatic, coherent and highly directional. It is used for cutting and welding, eye surgery, optical fibre communication and barcode readers.
- Needs: pumping, a metastable level and mirrors
- Properties: monochromatic, coherent, directional
Planck proposed that energy comes in quanta E = hf. In the photoelectric effect, light above a threshold frequency ejects electrons, and Einstein’s equation gives their kinetic energy. Radioactivity is the spontaneous decay of nuclei with alpha, beta and gamma emission. Mass defect provides the binding energy of a nucleus, and it is released in fission and fusion. X-rays are penetrating short-wave radiation. A laser gives coherent light through stimulated emission and population inversion.
- Photocurrent depends on intensity; the electrons’ energy depends on frequency.
- Fission splits heavy nuclei; fusion joins light ones.
- Population inversion means more atoms in the upper (metastable) state.
- Laser light is monochromatic, coherent and highly directional.
- 1 a.m.u. = 931 MeV.
Key formulas
- E = hf
- hf = φ + ½mv²
- E = mc²
- λ = c/f
Practice questions
The photoelectric equation was given by
- Planck
- Einstein
- Bohr
- Newton
Show the answer
Answer: B. Einstein hf = φ + KE.
Gamma rays are
- electrons
- helium nuclei
- electromagnetic waves
- neutrons
Show the answer
Answer: C. electromagnetic waves No charge.
LASER’s S stands for
- sound
- stimulated
- spontaneous
- speed
Show the answer
Answer: B. stimulated Light Amplification by Stimulated Emission of Radiation.
Nuclear reactors use
- fusion
- fission
- combustion
- photoemission
Show the answer
Answer: B. fission Controlled chain reaction.
Below threshold frequency, emission
- is large
- does not occur
- depends on brightness
- is delayed
Show the answer
Answer: B. does not occur Whatever the intensity.
X-rays are used in medicine for
- imaging bones
- heating food
- communication
- cooling
Show the answer
Answer: A. imaging bones They penetrate soft tissue.
Theory questions
What is population inversion? (2 marks)
Show the model answer
A state with more atoms in a higher (metastable) level than in a lower one, needed for laser action, and reached by pumping.
Light of energy 5 eV falls on a metal of work function 2 eV. Find the maximum KE of the electrons. (3 marks)
Show the model answer
KE = hf − φ = 3 eV.
Explain the photoelectric effect and state its laws and Einstein’s equation. (8 marks)
Show the model answer
Light of a suitable frequency ejects electrons from a metal. No electrons leave below the threshold frequency. Photocurrent is proportional to intensity. KE depends on frequency, not intensity. Emission is immediate. Einstein: a photon hf gives its energy to one electron, hf = φ + ½mv², explaining all these laws.
Electronics and semiconductors
Topics: Energy bands, doping, P-N junction and rectifiers.
Energy bands and doping
Electrons in a solid occupy bands of allowed energy. The valence band holds the bound electrons, and the conduction band holds those free to move. Between them may be a forbidden gap. In a conductor, these bands overlap, so plenty of electrons are free. In an insulator the gap is wide, about 5 eV or more. In a semiconductor it is small, about 1 eV, and heat can lift some electrons across. That is why a semiconductor’s resistance falls as temperature rises, unlike a metal’s.
Pure silicon or germanium is intrinsic, with equal numbers of electrons and holes. A hole is the vacancy left when an electron moves away, and it behaves like a positive charge. Adding a tiny amount of impurity is called doping. A pentavalent atom such as phosphorus or arsenic donates an extra electron, giving N-type material. A trivalent atom such as boron or aluminium leaves a hole, giving P-type material. Both types are still electrically neutral overall.
- Conductor: bands overlap
- Semiconductor: gap about 1 eV (Si 1.1 eV, Ge 0.7 eV)
- Insulator: gap of about 5 eV or more
- N-type: majority electrons
- P-type: majority holes
The P-N junction and rectifiers
Where P-type and N-type material meet, electrons and holes cross and cancel out near the junction. This leaves a thin depletion layer with a built-in barrier. In forward bias, with P connected to the positive terminal, the barrier falls and current flows once about 0.7 V is reached in silicon. In reverse bias the barrier rises, and almost no current flows. So a diode acts as a one-way valve.
A rectifier uses this to change AC into DC. A half-wave rectifier uses one diode and passes only one half of each cycle. A full-wave bridge uses four diodes, so both halves drive current the same way through the load. Its output has twice the frequency of the input and is easier to smooth with a capacitor filter.
A light emitting diode gives out light when forward biased, because electrons lose energy as they cross the junction. An LED needs a series resistor to limit its current.
- Half wave: V_dc = V_m/π, greatest efficiency ≈ 40.6%
- Full wave: V_dc = 2V_m/π, greatest efficiency ≈ 81.2%
- Ripple frequency: f for half wave, 2f for full wave
Example: A silicon diode and a 1 kΩ resistor are in series with a 5 V supply. Find the current, taking a 0.7 V drop across the diode.
- The voltage across the resistor = 5 − 0.7 = 4.3 V.
- I = 4.3/1000.
Answer: 4.3 mA
Example: An LED that drops 2 V and needs 20 mA runs from 9 V. Find the series resistor.
- The voltage across the resistor = 9 − 2 = 7 V.
- R = 7/0.02.
Answer: 350 Ω
Example: A peak voltage of 20 V is rectified. Find the DC output in half-wave and in full-wave.
- Half-wave: 20/π ≈ 6.37 V.
- Full-wave: 2 × 20/π ≈ 12.7 V.
Answer: About 6.4 V and 12.7 V
Energy bands explain conduction. Conductors have overlapping bands, insulators have a wide gap, and semiconductors have a small one. Doping creates N-type material (extra electrons) or P-type material (holes). A P-N junction conducts in forward bias and blocks in reverse bias, so it can rectify AC to DC. A transistor is a three-layer device, in PNP or NPN form. An LED gives out light in forward bias.
- Pure silicon or germanium is intrinsic; doped material is extrinsic.
- Pentavalent dopant (P, As) gives N-type; trivalent dopant (B, Al) gives P-type.
- A half-wave rectifier uses one diode; a bridge uses four.
- The resistance of a semiconductor falls as temperature rises.
Key formulas
- η_half-wave max ≈ 40.6%
- η_full-wave max ≈ 81.2%
- f_ripple(full) = 2f
Practice questions
Doping silicon with phosphorus gives
- P-type
- N-type
- an insulator
- a metal
Show the answer
Answer: B. N-type An extra electron.
In forward bias a diode has
- high resistance
- low resistance
- no current ever
- infinite voltage
Show the answer
Answer: B. low resistance It conducts.
A bridge rectifier uses
- 1 diode
- 2 diodes
- 4 diodes
- 8 diodes
Show the answer
Answer: C. 4 diodes Standard circuit.
The band gap is largest in
- conductors
- semiconductors
- insulators
- all equal
Show the answer
Answer: C. insulators Electrons cannot cross it.
Majority carriers in P-type are
- electrons
- holes
- ions
- protons
Show the answer
Answer: B. holes Trivalent doping.
LED stands for
- light emitting diode
- low energy device
- linear electronic diode
- light electric device
Show the answer
Answer: A. light emitting diode Definition.
Theory questions
Distinguish between intrinsic and extrinsic semiconductors. (2 marks)
Show the model answer
An intrinsic semiconductor is pure, with equal electrons and holes. An extrinsic one is doped, so one type of carrier dominates.
Explain conductors, semiconductors and insulators using energy bands. (5 marks)
Show the model answer
Conductors: valence and conduction bands overlap. Semiconductors: a small gap of about 1 eV is crossed by heat. Insulators: a large gap of about 5 eV or more stops conduction.
With a diagram, explain the working of a full-wave bridge rectifier. (8 marks)
Show the model answer
Four diodes form a bridge. In the positive half-cycle two opposite diodes conduct and current flows through the load in one direction. In the negative half-cycle the other two conduct and current through the load has the same direction. The output is pulsating DC at twice the input frequency, which a filter smooths.
Chapters follow the SCTE Assam syllabus. The notes and questions were written for this studio and are not official.