IITIAN1997 STUDIO

Applied Physics-II (NEP 2020)

Semester 2 · BS-202 · 44 MCQs and 23 theory questions

Open this subject studio →

Properties of matter: elasticity

Topics: Stress, strain, moduli, Hooke’s law, stress-strain curve.

Stress, strain and Hooke’s law

When a force changes a body’s shape or size, the particles inside pull back with a restoring force. An elastic body such as a steel spring returns to its shape when the load is removed. A plastic body such as clay keeps the new shape.

Stress is the restoring force per unit area, and strain is the fractional change in size. Using these rather than plain force and stretch lets us compare materials fairly: a thick wire and a thin wire of the same steel have the same stress-strain behaviour. Hooke’s law says that within the elastic limit, stress is directly proportional to strain. The constant ratio is called a modulus of elasticity.

Read the graph from the start as the wire is loaded. It is straight to the proportional limit, and the elastic limit is close to this. At the yield point, the strain grows with hardly any extra stress and the stretch becomes permanent. Stress then climbs to its highest value, the ultimate stress. After that the wire necks and it breaks at the fracture point. A ductile material has a long plastic region, and a brittle one breaks soon after the elastic limit.

  • Stress = F/A, in N/m²
  • Longitudinal strain = ΔL/L, with no unit
  • Modulus = stress/strain

Example: A 100 N load acts on a wire of area 1 mm², 2 m long, which stretches 1 mm. Find the stress, strain and Young’s modulus.

  1. Convert: A = 1 mm² = 10⁻⁶ m² and ΔL = 10⁻³ m.
  2. Stress = 100/10⁻⁶ = 10⁸ N/m².
  3. Strain = 10⁻³/2 = 5 × 10⁻⁴.
  4. Y = stress/strain = 10⁸/(5 × 10⁻⁴).

Answer: Stress 10⁸ N/m², strain 5 × 10⁻⁴, Y = 2 × 10¹¹ N/m²

The three moduli and Poisson’s ratio

A force can change a body in three ways, and each has a modulus. Young’s modulus Y deals with a change in length. Bulk modulus K deals with a change in volume under pressure. The modulus of rigidity η deals with a change in shape, when a sideways force makes a block lean without changing its volume.

A stretched wire also gets thinner. The ratio of the sideways strain to the lengthwise strain is Poisson’s ratio. It has no unit, and for most metals it lies near 0.3. A large modulus means a stiff material: steel has a larger Young’s modulus than rubber, even though rubber stretches further.

  • Y = FL/(AΔL)
  • K = V ΔP/ΔV, in size
  • η = shear stress/shear strain
  • Poisson’s ratio σ = (Δd/d)/(ΔL/L)

Example: A steel wire is 1 m long with area 2 mm², and Y = 2 × 10¹¹ N/m². How much does a 400 N load stretch it?

  1. From Y = FL/(AΔL), ΔL = FL/(AY).
  2. A = 2 × 10⁻⁶ m².
  3. ΔL = 400 × 1/(2 × 10⁻⁶ × 2 × 10¹¹) = 400/(4 × 10⁵).
  4. = 10⁻³ m.

Answer: 1 mm

Example: A wire 100 cm long stretches by 0.1 cm, and its 1 mm diameter falls by 0.0003 mm. Find Poisson’s ratio.

  1. Lengthwise strain = 0.1/100 = 10⁻³.
  2. Sideways strain = 0.0003/1 = 3 × 10⁻⁴.
  3. σ = 3 × 10⁻⁴/10⁻³.

Answer: 0.3

Example: Water has K = 2 × 10⁹ N/m². Find the percentage fall in its volume under an extra pressure of 10⁷ N/m².

  1. ΔV/V = ΔP/K.
  2. = 10⁷/(2 × 10⁹) = 0.005.
  3. As a percentage: 0.005 × 100.

Answer: 0.5%

A deforming force changes a body’s shape, and an internal restoring force opposes it. An elastic body returns to its shape, and a plastic body does not. Stress is the restoring force per unit area, and strain is the fractional change in size. Within the elastic limit, stress is proportional to strain (Hooke’s law), and the constant is a modulus of elasticity.

  • Young’s modulus for length, bulk modulus for volume, rigidity modulus for shape.
  • Stress has units of N/m²; strain has none.
  • The stress-strain curve shows the proportional limit, yield point and breaking point.
  • Poisson’s ratio = lateral strain/longitudinal strain.

Key formulas

  • Stress = F/A
  • Strain = ΔL/L
  • Y = FL/(AΔL)
  • K = −V ΔP/ΔV
  • η = shear stress/shear strain

Practice questions

Hooke’s law relates

  1. force and time
  2. stress and strain
  3. mass and volume
  4. heat and work
Show the answer

Answer: B. stress and strain Within the elastic limit.

The unit of stress is

  1. N
  2. N/m²
  3. m
  4. no unit
Show the answer

Answer: B. N/m² Force per area.

Strain has

  1. the unit N
  2. no unit
  3. the unit m
  4. the unit Pa
Show the answer

Answer: B. no unit A ratio of lengths.

Change of shape relates to

  1. Young’s modulus
  2. bulk modulus
  3. rigidity modulus
  4. density
Show the answer

Answer: C. rigidity modulus Shear.

Beyond the yield point a wire

  1. is fully elastic
  2. deforms permanently
  3. shortens
  4. gains mass
Show the answer

Answer: B. deforms permanently Plastic behaviour.

Theory questions

State Hooke’s law. (2 marks)

Show the model answer

Within the elastic limit, stress is directly proportional to strain.

A 2 m wire of area 1 mm² stretches by 1 mm under 100 N. Find Young’s modulus. (5 marks)

Show the model answer

Y = FL/(AΔL) = 100 × 2/(10⁻⁶ × 10⁻³) = 2 × 10¹¹ N/m².

Draw and explain the stress-strain curve of a ductile wire. (8 marks)

Show the model answer

It is straight up to the proportional limit, where Hooke’s law holds; the elastic limit is close to this. At the yield point, strain rises with little extra stress and the deformation becomes permanent. Stress then rises to the ultimate value, after which the wire necks and breaks at the fracture point.

Properties of matter: fluids

Topics: Thrust, pressure, Pascal’s law, hydraulic press and brakes; buoyancy, Archimedes, specific gravity; surface tension, viscosity.

Thrust, pressure and Pascal’s law

Thrust is the total force acting at right angles to a surface, and pressure is the thrust per unit area. This is why a sharp knife cuts well and a wide belt on a bag feels comfortable: a small area gives high pressure, and a large area gives low pressure.

In a liquid at rest, pressure rises with depth because of the weight of the liquid above, and it acts equally in all directions. It does not depend on the shape of the vessel, only on the depth and density. That is why a dam is built thicker at the bottom.

Pascal’s law says that pressure applied to an enclosed liquid passes equally to all parts. In a hydraulic press, a small force on a small piston creates a pressure, and this same pressure acts on a large piston and gives a large force. Nothing is gained for free: the large piston moves up by much less than the small piston moves down, so the work is the same. Hydraulic brakes use the same idea.

  • P = F/A, in pascal
  • P = hρg
  • F₁/A₁ = F₂/A₂
  • Movement: A₁d₁ = A₂d₂

Example: Find the water pressure at a depth of 10 m, with ρ = 1000 kg/m³ and g = 9.8 m/s².

  1. P = hρg.
  2. = 10 × 1000 × 9.8.

Answer: 98000 Pa, on top of atmospheric pressure

Example: A tank with a base of 2 m² holds water 1.5 m deep. Find the thrust on the base due to the water.

  1. P = 1.5 × 1000 × 9.8 = 14700 Pa.
  2. Thrust = P × A = 14700 × 2.

Answer: 29400 N

Example: A press has pistons of 10 cm² and 500 cm². What load does a 100 N effort lift? How far does the load rise if the small piston moves 10 cm?

  1. F₂ = F₁ × A₂/A₁ = 100 × 500/10 = 5000 N.
  2. Volume is conserved: 10 × 10 = 500 × d₂.
  3. d₂ = 100/500 = 0.2 cm.

Answer: 5000 N, and the load rises 0.2 cm

Buoyancy and Archimedes’ principle

A mug feels lighter under water, because the pressure on the bottom of an object is greater than on its top. This difference gives an upward force called upthrust or buoyancy. Archimedes’ principle says that this upthrust equals the weight of the fluid displaced.

Compare the weight with the upthrust. If the weight is greater, the body sinks. If the two are equal, it floats. A steel ship floats because its hollow shape displaces a large amount of water. A floating body sinks just far enough to displace its own weight of liquid.

Relative density, also called specific gravity, compares a substance with water. It has no unit. It can be measured by weighing a body in air and then in water, because the loss of weight is the weight of an equal volume of water.

  • Upthrust = Vρg
  • R.D. = density of substance/density of water
  • R.D. = weight in air/loss of weight in water
  • Floating: fraction under liquid = ρ_body/ρ_liquid

Example: A body weighs 20 N in air and 15 N in water. Find its upthrust, relative density and density.

  1. Upthrust = loss of weight = 20 − 15 = 5 N.
  2. R.D. = 20/5 = 4.
  3. Density = 4 × 1000 kg/m³.

Answer: Upthrust 5 N, R.D. 4, density 4000 kg/m³

Example: A wooden block of density 600 kg/m³ floats in water. What fraction of it is under water?

  1. For a floating body, weight = upthrust.
  2. Vρ_wood g = V_in ρ_water g.
  3. V_in/V = 600/1000.

Answer: 0.6, or 60%

Surface tension and viscosity

A molecule inside a liquid is pulled equally in all directions, but one at the surface is pulled mainly inward. So the surface behaves like a stretched skin and tries to become as small as possible. This surface tension is why drops are round and a light needle can rest on still water. It is measured as force per unit length, in N/m.

In a narrow tube, water rises because it wets the glass, while mercury falls because it does not. This is capillary action, and it helps a wick draw up oil. The height is greater in a narrower tube.

Viscosity is the internal friction of a fluid. Honey has a much higher viscosity than water. In steady flow, layers slide over each other, and the force between layers depends on the area and on the velocity gradient. A small sphere falling through a viscous fluid soon reaches a steady speed, called the terminal velocity, when gravity is balanced by upthrust and drag.

  • T = F/L
  • Capillary rise: h = 2T cos θ/(rρg)
  • Viscous force: F = ηA(dv/dx)
  • Stokes’ drag: F = 6πηrv

Example: Find the rise of water in a capillary of radius 0.5 mm, with T = 0.07 N/m, θ = 0°, ρ = 1000 kg/m³ and g = 9.8 m/s².

  1. Convert: r = 5 × 10⁻⁴ m. Also cos 0° = 1.
  2. Numerator: 2 × 0.07 = 0.14.
  3. Denominator: 5 × 10⁻⁴ × 1000 × 9.8 = 4.9.
  4. h = 0.14/4.9 ≈ 0.0286 m.

Answer: About 2.9 cm

Example: A plate of area 0.1 m² moves at 1 m/s over a fluid layer 1 cm thick, with η = 0.1 N s/m². Find the force.

  1. Velocity gradient = 1/0.01 = 100 per second.
  2. F = ηA(dv/dx).
  3. = 0.1 × 0.1 × 100.

Answer: 1 N

Thrust is the total normal force on a surface and pressure is thrust per unit area. Pressure in a liquid rises with depth. Pascal’s law says that pressure applied to an enclosed liquid is transmitted equally in all directions, which is the basis of the hydraulic press and brakes. Archimedes’ principle says that a body in a fluid feels an upthrust equal to the weight of the fluid displaced. Surface tension and viscosity describe a liquid’s surface and its internal friction.

  • A body floats when its weight equals the upthrust.
  • Relative density has no unit: density of substance/density of water.
  • A hydraulic press multiplies force by A₂/A₁.
  • Surface tension is force per unit length, in N/m; viscosity is measured in N s/m².

Key formulas

  • P = hρg
  • F₂ = F₁(A₂/A₁)
  • Upthrust = Vρg
  • R.D. = weight in air/loss of weight in water

Practice questions

The SI unit of pressure is

  1. N
  2. pascal
  3. joule
  4. watt
Show the answer

Answer: B. pascal 1 Pa = 1 N/m².

A hydraulic press works on

  1. Newton’s law
  2. Pascal’s law
  3. Hooke’s law
  4. Ohm’s law
Show the answer

Answer: B. Pascal’s law Pressure is transmitted equally.

Upthrust equals the weight of

  1. the body
  2. the liquid displaced
  3. the container
  4. the air
Show the answer

Answer: B. the liquid displaced Archimedes’ principle.

Pressure in a liquid increases with

  1. area
  2. depth
  3. colour
  4. shape of vessel
Show the answer

Answer: B. depth P = hρg.

Relative density has

  1. the unit kg/m³
  2. no unit
  3. the unit N
  4. the unit Pa
Show the answer

Answer: B. no unit A ratio.

Theory questions

State Pascal’s law. (2 marks)

Show the model answer

Pressure applied to an enclosed fluid is transmitted equally in all directions.

A hydraulic press has pistons of 10 cm² and 500 cm². Find the load lifted by a 100 N effort. (5 marks)

Show the model answer

F₂ = F₁ A₂/A₁ = 100 × 50 = 5000 N.

State Archimedes’ principle. A body weighs 20 N in air and 15 N in water. Find its relative density. (8 marks)

Show the model answer

A body in a fluid loses weight equal to the weight of the fluid displaced. Loss = 5 N. R.D. = 20/5 = 4.

Wave and oscillation

Topics: SHM, simple pendulum, resonance; wave motion and stationary waves; speed of sound and Laplace’s correction; ultrasonics; echo, reverberation, Sabine’s law, Doppler effect.

Simple harmonic motion

A swinging pendulum or a mass on a spring moves back and forth about a mean position. The motion is simple harmonic when the acceleration is proportional to the displacement and always directed toward the mean position. At the ends the body stops for a moment and its acceleration is greatest. At the mean position its speed is greatest and its acceleration is zero.

Displacement follows y = A sin ωt, where A is the amplitude, the greatest displacement. One complete swing takes the period T, and the frequency f is the number of swings in a second. For small swings, a pendulum’s period depends only on its length and g, not on its mass or amplitude. A seconds pendulum has a period of 2 s, and its length is about 1 m.

Every body has a natural frequency. If a periodic force acts at this same frequency, the amplitude grows large. This is resonance. It is how a radio tunes to a station, and it is why soldiers break step on a bridge.

  • y = A sin ωt
  • ω = 2πf = 2π/T
  • Greatest speed = Aω; greatest acceleration = Aω²
  • T = 2π√(l/g)

Example: Find the period of a pendulum 1 m long, with g = 9.8 m/s².

  1. T = 2π√(l/g).
  2. l/g = 1/9.8 = 0.102, and √0.102 = 0.319.
  3. T = 2 × 3.14 × 0.319.

Answer: About 2.0 s

Example: A motion is y = 0.05 sin(10πt), in SI units. Find the amplitude, frequency, period, greatest speed and greatest acceleration.

  1. Comparing with y = A sin ωt: A = 0.05 m and ω = 10π rad/s.
  2. f = ω/2π = 5 Hz, and T = 1/5 = 0.2 s.
  3. Greatest speed = Aω = 0.05 × 31.4 ≈ 1.57 m/s.
  4. Greatest acceleration = Aω² = 0.05 × 986.96 ≈ 49.3 m/s².

Answer: A = 0.05 m, f = 5 Hz, T = 0.2 s, 1.57 m/s and 49.3 m/s²

Waves and the speed of sound

A wave carries energy from place to place without carrying the material along. In a transverse wave, such as a wave on a string, the particles move across the direction of travel, forming crests and troughs. In a longitudinal wave, such as sound, they move along the direction of travel, forming compressions and rarefactions. Sound needs a medium, so it cannot travel through a vacuum.

Newton assumed that the compressions in air happen at constant temperature, and he got v = √(P/ρ), about 280 m/s. That is too low compared with the measured 332 m/s. Laplace pointed out that the changes are so fast that heat has no time to flow, which makes them adiabatic. Including the factor γ gives the correct value.

Speed in a gas rises with temperature, since v ∝ √T in kelvin, and rises with humidity. It does not change with pressure at a fixed temperature, since P/ρ stays constant. Sound also goes faster in liquids and solids than in air.

  • v = fλ
  • Newton: v = √(P/ρ)
  • Laplace: v = √(γP/ρ), with γ = 1.41 for air
  • Audible range: 20 Hz to 20 kHz

Example: Find the wavelength of a 512 Hz note in air, with v = 340 m/s.

  1. λ = v/f.
  2. = 340/512.

Answer: About 0.66 m

Example: Calculate the speed of sound at 0 °C, with P = 1.013 × 10⁵ Pa, ρ = 1.293 kg/m³ and γ = 1.41.

  1. P/ρ = 1.013 × 10⁵/1.293 = 78345.
  2. Newton: √78345 ≈ 280 m/s.
  3. Laplace: √(1.41 × 78345) = √110467.

Answer: About 332 m/s

Example: If sound travels at 332 m/s at 0 °C, find its speed at 30 °C.

  1. Convert: T₁ = 273 K and T₂ = 303 K.
  2. v₂/v₁ = √(T₂/T₁) = √(303/273) = 1.0535.
  3. v₂ = 332 × 1.0535.

Answer: About 350 m/s

Echo, ultrasonics and room acoustics

The ear holds a sound for about 0.1 s, so a reflected sound is heard separately only if it returns after this time. With sound at 340 m/s, this means a reflector at least about 17 m away. In a closed hall, repeated reflections keep a sound going after the source stops. This is reverberation, and the time is given by Sabine’s formula.

A good hall has a suitable reverberation time, no echoes and even loudness. If the time is too long, speech becomes unclear, so soft absorbing materials such as curtains and panels are added. Sound above 20 kHz is ultrasonic. It is used to find the depth of the sea (SONAR), to detect flaws in metal, and in medical imaging.

  • Echo: minimum distance = v × 0.1/2
  • Depth by echo: d = vt/2
  • Sabine: T = 0.16V/Σas, with V in m³ and absorption in m²

Example: An ultrasonic pulse returns from the sea bed in 2 s, at 1500 m/s. Find the depth.

  1. The pulse travels down and back, so use half the time.
  2. d = vt/2 = 1500 × 2/2.

Answer: 1500 m

Example: A hall has a volume of 1000 m³ and total absorption of 200 m². Find the reverberation time.

  1. T = 0.16V/Σas.
  2. = 0.16 × 1000/200.

Answer: 0.8 s

Doppler effect

A train’s horn sounds higher as it comes toward you and lower as it goes away. The waves ahead of a moving source are squeezed closer, and those behind it are spread out, so a listener hears a changed frequency. This is the Doppler effect. It is used in speed guns, in weather radar and in studying the motion of stars.

  • Source approaching: f′ = fv/(v − vₛ)
  • Source moving away: f′ = fv/(v + vₛ)

Example: A 500 Hz whistle approaches you at 20 m/s, with sound at 340 m/s. What frequency do you hear?

  1. f′ = fv/(v − vₛ).
  2. = 500 × 340/(340 − 20).
  3. = 500 × 340/320.

Answer: About 531 Hz

Stationary waves

When two equal waves travel in opposite directions along the same line, they combine to form a stationary wave. Some points, called nodes, never move, and others midway between, called antinodes, swing the most. Unlike a progressive wave, a stationary wave carries no net energy along the line.

A string fixed at both ends must have a node at each end. So only certain wavelengths fit, and this is why a guitar string gives definite notes. The distance between adjacent nodes is λ/2, so the lowest mode has λ = 2L.

  • Node to next node: λ/2
  • Node to next antinode: λ/4
  • String, lowest mode: f = v/(2L)

Example: A string 0.5 m long carries waves at 200 m/s. Find the lowest frequency.

  1. λ = 2L = 2 × 0.5 = 1 m.
  2. f = v/λ = 200/1.

Answer: 200 Hz

Simple harmonic motion has an acceleration proportional to displacement and directed toward the mean position. A wave carries energy without carrying matter: transverse if particles move across the direction of travel, longitudinal if along it. Sound is a longitudinal wave. Newton’s formula for its speed in air gave too low a value, and Laplace corrected it by using adiabatic conditions.

  • A seconds pendulum has a period of 2 s and a length near 1 m.
  • Audible range: 20 Hz to 20 kHz; above is ultrasonic, below is infrasonic.
  • Resonance happens when a driving frequency equals a natural frequency.
  • An echo needs about 0.1 s between the sounds.
  • Ocean depth = vt/2 by ultrasonic echo.
  • A stationary wave has nodes and antinodes and carries no net energy, unlike a progressive wave.

Key formulas

  • v = fλ
  • T = 2π√(l/g)
  • y = A sin ωt, ω = 2πf
  • v_Newton = √(P/ρ)
  • v_Laplace = √(γP/ρ)
  • d = vt/2
  • Sabine: T = 0.16V/ΣaS

Practice questions

Sound in air is

  1. transverse
  2. longitudinal
  3. electromagnetic
  4. stationary only
Show the answer

Answer: B. longitudinal Particles vibrate along the direction of travel.

Speed of a wave equals

  1. f/λ
  2. fλ
  3. λ/f
  4. f + λ
Show the answer

Answer: B. fλ v = fλ.

The audible range is

  1. 2 to 200 Hz
  2. 20 Hz to 20 kHz
  3. 20 to 200 kHz
  4. above 1 MHz
Show the answer

Answer: B. 20 Hz to 20 kHz For human hearing.

Laplace corrected Newton by using

  1. isothermal change
  2. adiabatic change
  3. a vacuum
  4. liquids
Show the answer

Answer: B. adiabatic change Sound is too fast for heat to flow.

The period of a seconds pendulum is

  1. 1 s
  2. 2 s
  3. 4 s
  4. 0.5 s
Show the answer

Answer: B. 2 s One second each way.

Resonance means

  1. zero amplitude
  2. equal natural and driving frequency
  3. no energy
  4. a change of medium
Show the answer

Answer: B. equal natural and driving frequency Amplitude becomes large.

In a stationary wave, points of zero displacement are

  1. antinodes
  2. nodes
  3. crests
  4. troughs
Show the answer

Answer: B. nodes Definition.

Theory questions

Define simple harmonic motion. (2 marks)

Show the model answer

Periodic motion in which acceleration is proportional to displacement from the mean position and directed toward it.

An ultrasonic pulse returns from the sea bed in 2 s. If its speed is 1500 m/s, find the depth. (3 marks)

Show the model answer

d = vt/2 = 1500 × 2/2 = 1500 m.

Give Newton’s formula for the speed of sound in air and explain Laplace’s correction. What factors affect this speed? (8 marks)

Show the model answer

Newton assumed isothermal change: v = √(P/ρ) ≈ 280 m/s, too low. Laplace took the changes as adiabatic: v = √(γP/ρ) ≈ 332 m/s, which agrees with experiment. Speed rises with temperature (v ∝ √T) and humidity and does not depend on pressure at a constant temperature.

Light

Topics: Mirrors; refractive index, critical angle, total internal reflection; optical fibre; prism; lenses and power; telescopes.

Mirrors and lenses

A plane mirror gives an upright image as far behind the mirror as the object is in front of it. A concave mirror converges light, and a convex mirror spreads it. Radius of curvature is twice the focal length. A lens works by refraction: a convex lens converges light to a focus, and a concave lens diverges it.

To find an image, follow two rays: one parallel to the axis, which passes through the focus after the lens, and one through the centre, which goes straight on. Watch the diagram as the object moves. Beyond 2F the image is real, inverted and smaller. Between F and 2F it is real, inverted and larger. Inside F, a convex lens gives an upright, enlarged, virtual image, which is how a magnifying glass works.

Use the Cartesian sign convention: measure from the pole or optical centre, with the direction of the incoming light as positive. An object usually has a negative u. A convex lens has a positive f and a concave mirror has a negative f.

  • Mirror: 1/f = 1/v + 1/u
  • Lens: 1/f = 1/v − 1/u
  • Magnification (lens): m = v/u
  • Power: P = 1/f, in dioptre, with f in metres
  • Lenses in contact: P = P₁ + P₂

Example: An object is 30 cm from a concave mirror of focal length 15 cm. Find the image.

  1. With signs, u = −30 and f = −15.
  2. 1/v = 1/f − 1/u = −1/15 + 1/30 = −1/30.
  3. v = −30 cm, in front of the mirror.

Answer: 30 cm in front: real, inverted, the same size

Example: An object is 30 cm from a convex lens of focal length 20 cm. Find the image and magnification.

  1. With signs, u = −30 and f = +20.
  2. 1/v = 1/f + 1/u = 1/20 − 1/30 = 1/60.
  3. v = +60 cm.
  4. m = v/u = 60/(−30) = −2.

Answer: 60 cm on the far side: real, inverted, twice the size

Example: Lenses of +5 D and −2 D touch each other. Find the combined power and focal length.

  1. P = 5 + (−2) = +3 D.
  2. f = 1/P = 1/3 m.

Answer: +3 D and about 33.3 cm

Refraction, critical angle and optical fibres

Light bends when it enters another medium, since its speed changes. Going into a denser medium, it bends toward the normal. Snell’s law says that sin i/sin r is constant for a given pair of media, and this constant is the refractive index. n also equals the speed of light in vacuum divided by its speed in the medium.

Going from denser to rarer, light bends away from the normal. As the angle of incidence grows, the refracted ray moves closer to the surface. At the critical angle C it runs along the surface. Beyond this, no light leaves at all, and it all reflects back. This is total internal reflection, and it needs two conditions: denser to rarer, and i greater than C.

An optical fibre has a glass core with a higher refractive index, covered with cladding of a lower index. Light strikes the wall above the critical angle and bounces along by total internal reflection, with little loss, even around bends. Fibres are used for internet links and in endoscopes. Numerical aperture measures how much light a fibre can accept.

  • n = sin i/sin r = c/v
  • sin C = 1/n
  • NA = √(n₁² − n₂²) = sin θ_max

Example: Light at 60° enters glass and refracts at 30°. Find the refractive index and the speed in the glass.

  1. n = sin 60°/sin 30° = 0.866/0.5 = 1.732.
  2. v = c/n = 3 × 10⁸/1.732.

Answer: n ≈ 1.73 and v ≈ 1.73 × 10⁸ m/s

Example: Find the critical angle for glass with n = 1.5.

  1. sin C = 1/n = 1/1.5 = 0.667.
  2. C = sin⁻¹(0.667).

Answer: About 41.8°

Example: A fibre has n₁ = 1.5 and n₂ = 1.46. Find the numerical aperture and the acceptance angle.

  1. NA = √(1.5² − 1.46²) = √(2.25 − 2.1316).
  2. = √0.1184 ≈ 0.344.
  3. θ = sin⁻¹(0.344).

Answer: NA ≈ 0.344 and about 20°

Prism and telescope

A prism bends light twice, and the angle between the incoming and outgoing rays is called the deviation. As the angle of incidence rises, the deviation falls to a minimum value D and then rises again. At minimum deviation, the ray passes symmetrically through the prism, and this gives a way to measure n. White light splits into colours, because each colour has its own refractive index.

An astronomical telescope has two convex lenses. The objective has a long focal length and forms a small real image of a distant object. The eyepiece has a short focal length and magnifies this image, like a magnifying glass. In normal adjustment, the final image is at infinity, and the tube length is the sum of the focal lengths.

  • n = sin((A + D)/2)/sin(A/2)
  • Telescope, normal adjustment: M = f₀/fₑ
  • Tube length = f₀ + fₑ

Example: A prism with A = 60° has a minimum deviation of 30°. Find n.

  1. (A + D)/2 = 45°, and A/2 = 30°.
  2. n = sin 45°/sin 30°.
  3. = 0.707/0.5.

Answer: About 1.41

Example: A telescope has f₀ = 100 cm and fₑ = 5 cm. Find the magnifying power and the tube length.

  1. M = f₀/fₑ = 100/5.
  2. Length = 100 + 5.

Answer: 20 times and 105 cm

Light reflects from mirrors and refracts on entering another medium. Mirror and lens formulas locate images using a sign convention. Refractive index n = sin i/sin r. When light goes from a denser to a rarer medium above the critical angle, it reflects totally, which is how an optical fibre guides light along its core. A prism deviates light and a telescope uses lenses to enlarge distant objects.

  • sin C = 1/n relates critical angle and refractive index.
  • Power of a lens P = 1/f, with f in metres; the unit is the dioptre.
  • A fibre has a core with a higher index than its cladding.
  • At minimum deviation, n = sin((A + D)/2)/sin(A/2).

Key formulas

  • 1/f = 1/v + 1/u (mirror)
  • 1/f = 1/v − 1/u (lens)
  • n = sin i/sin r
  • sin C = 1/n
  • NA = √(n₁² − n₂²)
  • n = sin((A + D)/2)/sin(A/2)
  • P = 1/f

Practice questions

Total internal reflection needs light to go from

  1. rarer to denser
  2. denser to rarer
  3. vacuum to glass
  4. air to water
Show the answer

Answer: B. denser to rarer And above the critical angle.

An optical fibre works on

  1. refraction only
  2. total internal reflection
  3. diffraction
  4. polarisation
Show the answer

Answer: B. total internal reflection Light stays in the core.

The unit of lens power is

  1. watt
  2. dioptre
  3. metre
  4. lumen
Show the answer

Answer: B. dioptre P = 1/f.

For glass with n = 1.5, sin C is

  1. 2/3
  2. 3/2
  3. 1/2
  4. 1
Show the answer

Answer: A. 2/3 1/n.

A convex lens of focal length 50 cm has power

  1. +2 D
  2. −2 D
  3. +0.5 D
  4. +50 D
Show the answer

Answer: A. +2 D 1/0.5.

An astronomical telescope’s magnifying power (normal) is

  1. f₀/fₑ
  2. fₑ/f₀
  3. f₀ + fₑ
  4. f₀fₑ
Show the answer

Answer: A. f₀/fₑ Objective over eyepiece.

Theory questions

Define critical angle and give its relation to refractive index. (2 marks)

Show the model answer

The angle of incidence in the denser medium for which the angle of refraction is 90°. sin C = 1/n.

An object is 30 cm from a convex lens of focal length 20 cm. Find the image position. (5 marks)

Show the model answer

1/v − 1/u = 1/f, with u = −30: 1/v = 1/20 − 1/30 = 1/60. v = +60 cm: a real image on the other side.

Explain the principle and structure of an optical fibre and find the numerical aperture for n₁ = 1.5 and n₂ = 1.46. (8 marks)

Show the model answer

Light enters a high-index core surrounded by lower-index cladding and travels by repeated total internal reflection. NA = √(1.5² − 1.46²) = √(2.25 − 2.1316) = √0.1184 ≈ 0.344. Fibres are used in communications and endoscopes.

Magnetism

Topics: Inverse square law; types of substances; dipole fields; tangent law; terrestrial magnetism.

Magnets and the inverse square law

Natural magnets such as lodestone occur in rock, and artificial ones are made from iron and its alloys. Every magnet has two poles. If you break a magnet, each piece has two poles, so an isolated pole has never been found. Like poles repel and unlike poles attract.

The force between two poles is proportional to the product of the pole strengths and inversely proportional to the square of the distance. Field lines leave the north pole and enter the south pole outside the magnet, and they form closed loops. They never cross, since a point cannot have two field directions.

A magnet in a uniform field feels a turning effect that tries to line it up with the field. A short magnet is a magnetic dipole with moment M. Its field at a distance d along its axis is twice its field at the same distance on the broad-side line.

  • F = (μ₀/4π) m₁m₂/r², with μ₀/4π = 10⁻⁷
  • τ = MB sin θ
  • Short dipole, axial: B = (μ₀/4π) 2M/d³
  • Short dipole, broad-side: B = (μ₀/4π) M/d³
  • Tangent law: B = H tan θ

Example: Poles of 10 A m and 20 A m are 10 cm apart. Find the force.

  1. F = 10⁻⁷ × m₁m₂/r².
  2. = 10⁻⁷ × 200/(0.1)².
  3. = 10⁻⁷ × 20000.

Answer: 2 × 10⁻³ N

Example: A short magnet has M = 2 A m². Find its field 20 cm away on the axis and on the broad-side line.

  1. d³ = 0.2³ = 0.008.
  2. Axial: 10⁻⁷ × 2 × 2/0.008 = 5 × 10⁻⁵ T.
  3. Broad-side: half of this.

Answer: 5 × 10⁻⁵ T and 2.5 × 10⁻⁵ T

Example: Find the torque on a magnet with M = 2 A m² at 30° to a 0.5 T field.

  1. τ = MB sin θ.
  2. = 2 × 0.5 × sin 30°.

Answer: 0.5 N m

Example: A magnetometer needle deflects 60° where H = 3.2 × 10⁻⁵ T. Find the magnet’s field.

  1. The tangent law gives B = H tan θ.
  2. tan 60° = 1.732.
  3. B = 3.2 × 10⁻⁵ × 1.732.

Answer: About 5.5 × 10⁻⁵ T

Magnetic substances

Materials respond to a magnetic field in three ways. Diamagnetic materials such as bismuth and copper are weakly repelled, with a small negative susceptibility. Paramagnetic materials such as aluminium are weakly attracted, with a small positive susceptibility. Ferromagnetic materials such as iron, nickel and cobalt are strongly attracted, and they can keep their magnetism.

Soft iron magnetises easily and loses it easily, so it is used in transformer cores and electromagnets. Steel holds on to its magnetism, so it is used for permanent magnets. Heating a ferromagnet above its Curie temperature makes it paramagnetic.

  • Diamagnetic: Bi, Cu
  • Paramagnetic: Al
  • Ferromagnetic: Fe, Ni, Co

The Earth as a magnet

A freely hanging compass settles nearly north-south, because the Earth behaves like a huge magnet. Three elements describe its field at any place. Declination is the angle between the geographic and the magnetic meridian. Dip is the angle that the field makes with the horizontal. The third is the horizontal component H.

A dip needle is horizontal at the magnetic equator and vertical at the magnetic poles. The total field B splits into a horizontal part and a vertical part. A compass responds to H, and that is why it does not work well near the magnetic poles.

  • H = B cos δ
  • V = B sin δ
  • tan δ = V/H
  • B² = H² + V²

Example: At a place where the dip is 60°, H = 0.3 G. Find the total field and the vertical part.

  1. B = H/cos δ = 0.3/0.5 = 0.6 G.
  2. V = B sin δ = 0.6 × 0.866.

Answer: B = 0.6 G and V ≈ 0.52 G

Like magnetic poles repel and unlike poles attract, with a force following an inverse square law. A dipole’s field is stronger on its end-on (axial) position than at the same distance broad-side on. Substances are diamagnetic, paramagnetic or ferromagnetic. The tangent law is used in a deflection magnetometer. The Earth behaves as a magnet described by three elements: declination, dip and the horizontal component.

  • Magnetic field lines form closed loops and never cross.
  • Ferromagnets such as iron are strongly attracted; diamagnets are weakly repelled.
  • Tangent law: B = H tan θ.
  • At the magnetic poles dip is 90°, and at the equator it is 0°.
  • H = B cos δ, V = B sin δ.

Key formulas

  • F = (μ₀/4π) m₁m₂/r²
  • B_axial = (μ₀/4π) 2Md/(d² − l²)²
  • τ = MB sin θ
  • B = H tan θ

Practice questions

Iron is

  1. diamagnetic
  2. paramagnetic
  3. ferromagnetic
  4. non-magnetic
Show the answer

Answer: C. ferromagnetic Strongly magnetised.

Dip at the magnetic equator is

  1. 0°
  2. 45°
  3. 90°
  4. 180°
Show the answer

Answer: A. 0° The needle is horizontal.

Field lines of a magnet

  1. cross each other
  2. form closed loops
  3. are straight only
  4. start and end in air
Show the answer

Answer: B. form closed loops No isolated poles.

Torque on a magnet in a field is

  1. MB sin θ
  2. MB cos θ
  3. MB
  4. M/B
Show the answer

Answer: A. MB sin θ τ = MB sin θ.

The angle between geographic and magnetic meridians is

  1. dip
  2. declination
  3. inclination
  4. tangent
Show the answer

Answer: B. declination Definition.

Theory questions

Name the elements of terrestrial magnetism. (2 marks)

Show the model answer

Declination, dip (inclination) and the horizontal component of Earth’s field.

Dip at a place is 60° and H is 0.3 G. Find the total field. (3 marks)

Show the model answer

B = H/cos δ = 0.3/0.5 = 0.6 G.

Compare diamagnetic, paramagnetic and ferromagnetic substances with examples. (8 marks)

Show the model answer

Diamagnetic: weakly repelled, small negative susceptibility, such as bismuth and copper. Paramagnetic: weakly attracted, small positive susceptibility, such as aluminium. Ferromagnetic: strongly attracted, large susceptibility and retained magnetism, such as iron, nickel and cobalt.

Modern physics

Topics: Photoelectric effect and cells; radioactivity, binding energy, fission and fusion; X-rays; lasers.

Quanta and the photoelectric effect

Planck proposed that light energy comes in packets, called quanta or photons, each with an energy E = hf. A convenient form is E in eV ≈ 1240/λ, with λ in nm. Blue light has more energy per photon than red.

When light of a suitable frequency falls on a clean metal, electrons are ejected. The wave picture of light cannot explain the results. Below a threshold frequency, no electrons leave, however bright the light. Above it, electrons leave immediately. Their greatest kinetic energy depends on the frequency, not the brightness. Brighter light gives more electrons, and so a larger current, without giving them more energy.

Einstein explained this using photons. One photon gives all its energy to one electron. Part of it, the work function φ, frees the electron from the metal, and the rest becomes kinetic energy.

  • E = hf = hc/λ, with h = 6.63 × 10⁻³⁴ J s
  • hf = φ + ½mv²
  • Threshold: hf₀ = φ
  • Stopping potential: eV₀ = ½mv²

Example: Find the energy of a 620 nm photon, in eV.

  1. E ≈ 1240/λ.
  2. = 1240/620.

Answer: 2 eV

Example: A metal has φ = 2 eV, and photons of 5 eV fall on it. Find the greatest KE and the stopping potential.

  1. KE = hf − φ = 5 − 2 = 3 eV.
  2. The stopping potential in volts equals the KE in eV.

Answer: 3 eV and 3 V

Example: Find the threshold wavelength for a metal with φ = 2.3 eV.

  1. At the threshold, E = φ.
  2. λ₀ ≈ 1240/2.3.

Answer: About 539 nm

Photocells

A photocell converts light into an electrical signal. A photo-emissive cell uses the photoelectric effect directly, with electrons leaving a cathode in a vacuum. A photo-conductive cell has a semiconductor whose resistance falls in light, which suits street-light switches. A photo-voltaic cell, the type used in solar panels, produces an emf directly from light falling on a P-N junction.

  • Photo-emissive: electrons leave a surface
  • Photo-conductive: resistance falls in light
  • Photo-voltaic: light produces an emf

Radioactivity and the nucleus

Some heavy nuclei are unstable and decay on their own, unaffected by temperature or pressure. Alpha particles are helium nuclei: they are heavy, ionise strongly and are stopped by paper. Beta particles are fast electrons. Gamma rays are high-energy electromagnetic waves with no charge, and they penetrate the most.

Half-life is the time for half of the nuclei to decay. It is constant for each isotope. Alpha emission reduces the mass number by 4 and the atomic number by 2. Beta emission keeps the mass number the same and raises the atomic number by 1.

A nucleus has less mass than its separate protons and neutrons. The difference, called the mass defect, is the binding energy, given by E = mc². Splitting a heavy nucleus (fission) or joining light nuclei (fusion) gives more tightly bound products and releases energy. Nuclear reactors use controlled fission, and the Sun runs on fusion.

  • After n half-lives: N = N₀/2ⁿ
  • E = mc²
  • 1 u = 931 MeV

Example: A 16 g sample has a half-life of 5 days. How much remains after 15 days?

  1. Number of half-lives: 15/5 = 3.
  2. N = 16/2³ = 16/8.

Answer: 2 g

Example: A helium nucleus has a mass of 4.00151 u. A proton is 1.00728 u, and a neutron is 1.00866 u. Find the binding energy.

  1. Parts: 2(1.00728) + 2(1.00866) = 4.03188 u.
  2. Mass defect: 4.03188 − 4.00151 = 0.03037 u.
  3. Energy: 0.03037 × 931 ≈ 28.3 MeV.
  4. Per nucleon: 28.3/4 ≈ 7.07 MeV.

Answer: About 28.3 MeV, or 7.07 MeV per nucleon

X-rays

X-rays are electromagnetic waves of very short wavelength. They are produced when fast electrons, accelerated by a high voltage in a Coolidge tube, strike a metal target. Most of the energy becomes heat, so the target needs a high melting point. The shortest wavelength occurs when an electron gives all its energy to one photon, and so it depends on the tube voltage.

X-rays pass through soft tissue but are absorbed more by bone, which is why they are used in medical imaging. Other uses include finding flaws in metal castings and studying crystal structure. Too much exposure is harmful, so operators use lead shielding.

  • eV = hc/λ_min
  • λ_min (Å) ≈ 12400/V

Example: Find the shortest wavelength from an X-ray tube at 40 kV.

  1. λ_min ≈ 12400/V.
  2. = 12400/40000.

Answer: About 0.31 Å

Lasers

LASER stands for Light Amplification by Stimulated Emission of Radiation. An atom in a higher level can drop down by itself at a random moment, which is spontaneous emission. However, a passing photon of the right energy can trigger the drop, and the new photon is an exact copy of the first. This is stimulated emission.

Normally most atoms are in the lower level, so photons get absorbed more often than copied. Pumping lifts atoms into a metastable level where they stay for a long time, until more atoms are up than down. This is population inversion. Mirrors at the ends send the light back and forth, building a strong beam.

Laser light is monochromatic, coherent and highly directional. It is used for cutting and welding, eye surgery, optical fibre communication and barcode readers.

  • Needs: pumping, a metastable level and mirrors
  • Properties: monochromatic, coherent, directional

Planck proposed that energy comes in quanta E = hf. In the photoelectric effect, light above a threshold frequency ejects electrons, and Einstein’s equation gives their kinetic energy. Radioactivity is the spontaneous decay of nuclei with alpha, beta and gamma emission. Mass defect provides the binding energy of a nucleus, and it is released in fission and fusion. X-rays are penetrating short-wave radiation. A laser gives coherent light through stimulated emission and population inversion.

  • Photocurrent depends on intensity; the electrons’ energy depends on frequency.
  • Fission splits heavy nuclei; fusion joins light ones.
  • Population inversion means more atoms in the upper (metastable) state.
  • Laser light is monochromatic, coherent and highly directional.
  • 1 a.m.u. = 931 MeV.
  • Photo-emissive, photo-conductive and photo-voltaic cells convert light into electrical signals or power.

Key formulas

  • E = hf
  • hf = φ + ½mv²
  • E = mc²
  • λ = c/f

Practice questions

The photoelectric equation was given by

  1. Planck
  2. Einstein
  3. Bohr
  4. Newton
Show the answer

Answer: B. Einstein hf = φ + KE.

Gamma rays are

  1. electrons
  2. helium nuclei
  3. electromagnetic waves
  4. neutrons
Show the answer

Answer: C. electromagnetic waves No charge.

LASER’s S stands for

  1. sound
  2. stimulated
  3. spontaneous
  4. speed
Show the answer

Answer: B. stimulated Light Amplification by Stimulated Emission of Radiation.

Nuclear reactors use

  1. fusion
  2. fission
  3. combustion
  4. photoemission
Show the answer

Answer: B. fission Controlled chain reaction.

Below threshold frequency, emission

  1. is large
  2. does not occur
  3. depends on brightness
  4. is delayed
Show the answer

Answer: B. does not occur Whatever the intensity.

X-rays are used in medicine for

  1. imaging bones
  2. heating food
  3. communication
  4. cooling
Show the answer

Answer: A. imaging bones They penetrate soft tissue.

Theory questions

What is population inversion? (2 marks)

Show the model answer

A state with more atoms in a higher (metastable) level than in a lower one, needed for laser action, and reached by pumping.

Light of energy 5 eV falls on a metal of work function 2 eV. Find the maximum KE of the electrons. (3 marks)

Show the model answer

KE = hf − φ = 3 eV.

Explain the photoelectric effect and state its laws and Einstein’s equation. (8 marks)

Show the model answer

Light of a suitable frequency ejects electrons from a metal. No electrons leave below the threshold frequency. Photocurrent is proportional to intensity. KE depends on frequency, not intensity. Emission is immediate. Einstein: a photon hf gives its energy to one electron, hf = φ + ½mv², explaining all these laws.

Heat and thermodynamics

Topics: Heat, calorimetry; temperature scales; heat transfer; change of state; expansion, gas laws; laws of thermodynamics, heat engines.

Temperature and thermal expansion

Heat is energy that passes from a hot body to a colder one, and temperature tells us how hot a body is. A large tank of warm water holds more heat than a cup of boiling water, even though its temperature is lower. On the Celsius scale water freezes at 0 °C and boils at 100 °C. The same points are 32 °F and 212 °F on the Fahrenheit scale, and 273 K and 373 K on the Kelvin scale.

Most things expand when heated, because the particles vibrate more and move further apart. Solids have expansion in length, area and volume, with coefficients in the ratio 1 : 2 : 3. This is why railway lines have gaps and bridges have expansion joints.

Water is unusual. As it is heated from 0 °C to 4 °C it contracts, so it is densest at 4 °C. This is why a lake freezes from the top, and fish can survive in the water below the ice.

  • K = °C + 273
  • °F = 9C/5 + 32
  • L₂ = L₁(1 + αΔT)
  • β = 2α and γ = 3α

Example: Convert 98.6 °F to °C and K.

  1. C = (F − 32) × 5/9.
  2. = 66.6 × 5/9 = 37 °C.
  3. K = 37 + 273.

Answer: 37 °C = 310 K

Example: A 10 m steel rail warms by 40 °C, with α = 1.2 × 10⁻⁵ per °C. Find the expansion.

  1. ΔL = L₁αΔT.
  2. = 10 × 1.2 × 10⁻⁵ × 40.
  3. = 4.8 × 10⁻³ m.

Answer: 4.8 mm

Calorimetry and change of state

The heat needed to warm a body depends on its mass, the rise in temperature and the material. Specific heat c is the heat needed to warm 1 kg by 1 K. Water has a large value, 4200 J/kg K, which makes it a good coolant. When a hot body and a cold body are mixed with no loss to the outside, the heat lost by one equals the heat gained by the other. This is the principle of calorimetry.

During melting or boiling the temperature stays constant even as heat is supplied, because the energy goes into separating the particles. This hidden heat is called latent heat. It makes the flat steps on the graph. Steam at 100 °C causes a worse burn than water at 100 °C because it also gives up its latent heat as it condenses.

Pressure affects melting and boiling points. Increased pressure lowers the melting point of ice. This effect is regelation: a loaded wire passes through a block of ice, and the water refreezes behind it. Increased pressure raises the boiling point of water, which is how a pressure cooker works.

  • Q = mcΔT
  • Q = mL
  • Heat lost = heat gained
  • L for ice ≈ 336 kJ/kg, L for steam ≈ 2260 kJ/kg

Example: Mix 200 g of water at 80 °C with 300 g at 30 °C. Find the final temperature.

  1. Heat lost = heat gained: 200 × c × (80 − T) = 300 × c × (T − 30). The c cancels.
  2. 16000 − 200T = 300T − 9000.
  3. 25000 = 500T.

Answer: T = 50 °C

Example: Find the heat needed to change 1 kg of ice at 0 °C into water at 20 °C, with L = 336 kJ/kg and c = 4.2 kJ/kg K.

  1. Melting: Q₁ = mL = 1 × 336 = 336 kJ.
  2. Warming: Q₂ = mcΔT = 1 × 4.2 × 20 = 84 kJ.
  3. Add the two.

Answer: 420 kJ

Heat transfer

Heat travels in three ways. In conduction, the energy passes from particle to particle while the particles stay in place, mainly in solids. A metal spoon in hot tea becomes hot this way. In convection, the hot fluid itself moves: it expands, becomes lighter and rises, as in boiling water and sea breezes. Radiation needs no medium at all, which is how the Sun’s heat reaches us through space.

The rate of conduction through a slab increases with its area and temperature difference, and falls with its thickness. The constant k is the thermal conductivity. Metals have a high k, while wood, wool and air have a low k. A wool sweater keeps you warm because it traps still air.

  • Q/t = kA(T₁ − T₂)/d
  • k is in W/m K
  • Dark, rough surfaces absorb and emit radiation well; shiny ones do so poorly

Example: A bar has k = 400 W/m K, area 0.01 m² and length 0.5 m, with its ends 50 K apart. Find the rate of heat flow.

  1. Q/t = kAΔT/d.
  2. = 400 × 0.01 × 50/0.5.
  3. = 200/0.5.

Answer: 400 W

Gas laws and the laws of thermodynamics

Boyle’s law says that at a constant temperature, the pressure of a fixed mass of gas is inversely proportional to its volume. Charles’s law says that at a constant pressure, volume is proportional to the absolute temperature. They combine into PV/T = constant, and temperatures must be in kelvin.

The first law of thermodynamics is conservation of energy: heat given to a system goes partly into raising its internal energy and partly into doing work. The second law sets a limit. No engine working in a cycle can change all the heat it takes in into work. Some must always be rejected to a colder place. So a heat engine takes Q₁ from a hot source, does work W and rejects Q₂ to a sink, and its efficiency is always below 100%.

  • P₁V₁ = P₂V₂ at constant T
  • V₁/T₁ = V₂/T₂ at constant P
  • ΔQ = ΔU + ΔW
  • η = W/Q₁ = 1 − Q₂/Q₁

Example: A gas at 2 atm occupies 3 L. Find its volume at 1 atm with no change in temperature.

  1. P₁V₁ = P₂V₂.
  2. 2 × 3 = 1 × V₂.

Answer: 6 L

Example: A gas occupies 3 L at 27 °C. Find its volume at 127 °C at the same pressure.

  1. Convert to kelvin: 300 K and 400 K.
  2. V₂ = V₁ × T₂/T₁ = 3 × 400/300.

Answer: 4 L

Example: A system takes in 500 J of heat and does 200 J of work. Find the rise in internal energy.

  1. ΔQ = ΔU + ΔW.
  2. 500 = ΔU + 200.

Answer: ΔU = 300 J

Example: An engine takes in 1000 J and rejects 600 J in each cycle. Find the work and efficiency.

  1. W = Q₁ − Q₂ = 400 J.
  2. η = 400/1000 = 0.4.

Answer: 400 J per cycle, and 40% efficiency

Heat is energy in transit because of a temperature difference, and temperature measures how hot a body is. Heat Q = mcΔT raises a temperature, and Q = mL changes the state at a fixed temperature. Heat travels by conduction, convection and radiation. Solids, liquids and gases expand when heated. The first law of thermodynamics is energy conservation, and the second says that no heat engine can convert all heat into work.

  • °C to K: add 273; °F = 9C/5 + 32.
  • α : β : γ = 1 : 2 : 3.
  • Water contracts when heated from 0 to 4 °C, so it is densest at 4 °C.
  • Boyle’s law: PV is constant at a fixed temperature.
  • Regelation: pressure lowers the melting point of ice.

Key formulas

  • Q = mcΔT
  • Q = mL
  • L₂ = L₁(1 + αΔT)
  • P₁V₁ = P₂V₂
  • Q = kAΔTt/d
  • ΔQ = ΔU + ΔW
  • η = 1 − Q₂/Q₁

Practice questions

The SI unit of specific heat is

  1. J/kg K
  2. J/kg
  3. J
  4. W
Show the answer

Answer: A. J/kg K Q = mcΔT.

Water has its maximum density at

  1. 0 °C
  2. 4 °C
  3. 100 °C
  4. −4 °C
Show the answer

Answer: B. 4 °C Anomalous expansion.

Heat from the Sun reaches us by

  1. conduction
  2. convection
  3. radiation
  4. all equally
Show the answer

Answer: C. radiation No medium is needed.

27 °C in kelvin is

  1. 27
  2. 246
  3. 300
  4. 373
Show the answer

Answer: C. 300 27 + 273.

The first law of thermodynamics is about

  1. momentum
  2. energy conservation
  3. entropy only
  4. force
Show the answer

Answer: B. energy conservation ΔQ = ΔU + ΔW.

The relation between linear and cubical expansion is

  1. γ = α
  2. γ = 2α
  3. γ = 3α
  4. γ = α/3
Show the answer

Answer: C. γ = 3α For small expansion.

Theory questions

Convert 98.6 °F to °C. (2 marks)

Show the model answer

C = (98.6 − 32) × 5/9 = 37 °C.

How much heat is needed to change 1 kg of ice at 0 °C to water at 20 °C? (L = 336 kJ/kg, c = 4.2 kJ/kg K) (5 marks)

Show the model answer

Melting 336 kJ + heating 1 × 4.2 × 20 = 84 kJ. Total 420 kJ.

State the first and second laws of thermodynamics and explain the basic idea of a heat engine. (8 marks)

Show the model answer

First law: heat supplied = rise in internal energy + work done. Second law: no engine operating in a cycle can convert all the heat it takes into work. An engine takes Q₁ from a hot source, does work W and rejects Q₂ to a sink; η = W/Q₁ = 1 − Q₂/Q₁, always below 1.

Nano physics

Topics: Nanomaterials, their types and applications.

What nanomaterials are and why size matters

A nanometre is 10⁻⁹ m, about a billionth of a metre. A nanomaterial has at least one dimension between about 1 and 100 nm. At this size, properties can differ greatly from those of the same material in bulk. Gold nanoparticles can look red instead of golden, and some materials become better catalysts or much stronger.

The main reason is surface area. Cut a cube into smaller cubes: the total volume stays the same, but the total surface grows. Surface area per unit volume is 6/a for a cube of side a, so it becomes enormous as a becomes small. More atoms sit at the surface, where they are free to react. At the smallest sizes, quantum effects also change the electrical and optical behaviour.

  • 0-D: nanoparticles and quantum dots
  • 1-D: nanotubes and nanowires
  • 2-D: thin films and graphene sheets
  • Surface/volume of a cube = 6/a

Example: A 1 cm cube is cut into cubes of side 1 mm. By what factor does the total surface grow?

  1. Original surface = 6 × 1² = 6 cm² = 600 mm².
  2. Number of small cubes = 10³ = 1000.
  3. New surface = 1000 × 6 × 1² = 6000 mm².
  4. Ratio = 6000/600.

Answer: 10 times

Example: Compare the surface-to-volume ratio of a cube of side 1 cm with one of side 10 nm.

  1. Side 1 cm = 10⁻² m: 6/10⁻² = 600 per metre.
  2. Side 10 nm = 10⁻⁸ m: 6/10⁻⁸ = 6 × 10⁸ per metre.
  3. Ratio = 6 × 10⁸/600.

Answer: A million times greater

Applications and care

Nanomaterials are already in everyday use. Sunscreens use nanoparticles of titanium dioxide or zinc oxide. Medicines can use nanocarriers to reach particular cells. Electronics use ever smaller structures, and coatings can resist scratches or repel water. Nanotubes give very strong, light composites.

Their small size also raises concerns: particles may enter the body or the environment in ways that bulk materials do not. Health and environmental effects are still being studied, so such materials need to be handled carefully.

  • Medicine: drug delivery and imaging
  • Electronics: sensors and memory
  • Materials: strong composites and coatings
  • Energy: catalysts and better batteries

Nanomaterials have at least one dimension of about 1 to 100 nanometres. At this size, the ratio of surface to volume is very large and properties change compared with the bulk material. They include nanoparticles, nanotubes and thin films, used in medicine, electronics, coatings and catalysts.

  • Types: 0-D (particles), 1-D (tubes and wires), 2-D (films).
  • Gold nanoparticles can look red, not gold.
  • Applications: sunscreens, drug delivery and sensors.
  • Health and environmental effects are still being studied.

Key formulas

  • 1 nm = 10⁻⁹ m

Practice questions

One nanometre is

  1. 10⁻³ m
  2. 10⁻⁶ m
  3. 10⁻⁹ m
  4. 10⁻¹² m
Show the answer

Answer: C. 10⁻⁹ m Definition.

Nanomaterials have a high

  1. mass
  2. surface-to-volume ratio
  3. length
  4. cost always
Show the answer

Answer: B. surface-to-volume ratio Key reason for new properties.

A carbon nanotube is

  1. 0-D
  2. 1-D
  3. 2-D
  4. 3-D
Show the answer

Answer: B. 1-D Long and thin.

A nanoparticle’s size is about

  1. 1–100 nm
  2. 1–100 mm
  3. 1–100 m
  4. 1–100 km
Show the answer

Answer: A. 1–100 nm Standard range.

Theory questions

What are nanomaterials? (2 marks)

Show the model answer

Materials with at least one dimension of about 1 to 100 nm, whose properties differ from those of the bulk material.

Give the types of nanomaterials and four applications. (5 marks)

Show the model answer

Types: 0-D particles, 1-D tubes and wires, 2-D films. Applications: drug delivery, sensors, catalysts and protective coatings.

Chapters follow the SCTE Assam syllabus. The notes and questions were written for this studio and are not official.

Open this subject studio →