IITIAN1997 STUDIO

Engineering Mechanics (NEP 2020)

Semester 2 · ES-206 · 42 MCQs and 22 theory questions

Open this subject studio →

Unit I: Force systems

Topics: Force as a vector, transmissibility, resolution; resultant of coplanar concurrent, non-concurrent and parallel forces; Bow’s notation, funicular polygon.

Force and the parallelogram law

A force is a push or a pull. It is a vector, so a number alone does not describe it: you need its magnitude, its direction, its point of application and its line of action. Its SI unit is the newton, the force that gives 1 kg an acceleration of 1 m/s².

Forces that act in one plane are coplanar. If their lines of action all pass through one point they are concurrent; if they are parallel, they form a parallel system; otherwise they are non-concurrent. By the principle of transmissibility, a force on a rigid body can slide anywhere along its own line of action without changing its effect, which is why only the line matters, not the exact point on it.

Two forces at a point can be replaced by one, their resultant. By the parallelogram law, if the two forces are drawn as adjacent sides of a parallelogram, the diagonal through their meeting point gives the resultant. The triangle law says the same thing by placing the forces head to tail, and the polygon law extends it to any number of forces.

  • R² = P² + Q² + 2PQ cos θ
  • tan α = Q sin θ/(P + Q cos θ), with α measured from P
  • θ = 0: R = P + Q. θ = 180°: R = P − Q. θ = 90°: R = √(P² + Q²)
  • Two equal forces F at θ: R = 2F cos(θ/2)
  • Transmissibility: a force may slide along its line of action

Example: Forces of 30 N and 40 N act at a point with 60° between them. Find the resultant and its direction.

  1. R² = 900 + 1600 + 2 × 30 × 40 × cos 60° = 3700.
  2. R = √3700 ≈ 60.8 N.
  3. tan α = 40 sin 60°/(30 + 40 cos 60°) = 34.64/50 = 0.693, so α ≈ 34.7° from the 30 N force.

Answer: R ≈ 60.8 N, at about 34.7° to the 30 N force

Example: Two equal forces of 50 N act at a point with 120° between them. Find the resultant.

  1. R = 2F cos(θ/2) = 2 × 50 × cos 60°.
  2. = 100 × 0.5.

Answer: 50 N, along the bisector of the angle

Example: Two forces at right angles have a resultant of 13 N. One of them is 5 N. Find the other.

  1. R² = P² + Q² when θ = 90°.
  2. Q² = 169 − 25 = 144.

Answer: 12 N

Resolution, and many forces at a point

Any force can be split into two perpendicular parts, its components. A force F at θ to the x-axis has Fx = F cos θ and Fy = F sin θ. Resolving is the reverse of the parallelogram law, and it is usually the easiest way to handle three or more forces.

For many forces at a point, resolve each one, add all the x-parts to get ΣFx and all the y-parts to get ΣFy, then combine. Keep signs with care: a component pointing left or down is negative. The direction of the resultant comes from tan α = ΣFy/ΣFx, but check the signs to put the angle in the right quadrant.

Graphical methods give the same answers. In the polygon method, forces are drawn to scale head to tail; the closing side, from the start to the last head, is the resultant. Bow’s notation names each force by the two spaces on either side of it (AB, BC and so on), which keeps a vector diagram in step with its space diagram.

  • Fx = F cos θ, Fy = F sin θ
  • R = √((ΣFx)² + (ΣFy)²)
  • tan α = ΣFy/ΣFx, with the quadrant from the signs
  • Polygon law: the closing side is the resultant
  • Bow’s notation: spaces are lettered, forces named by two letters

Example: Resolve a 100 N force acting at 30° above the horizontal.

  1. Fx = 100 cos 30° = 86.6 N.
  2. Fy = 100 sin 30° = 50 N.

Answer: 86.6 N horizontal and 50 N vertical

Example: Forces of 20 N, 30 N and 40 N act at a point at 0°, 60° and 150° to the x-axis. Find the resultant.

  1. ΣFx = 20 + 30 cos 60° + 40 cos 150° = 20 + 15 − 34.64 = 0.36 N.
  2. ΣFy = 0 + 30 sin 60° + 40 sin 150° = 25.98 + 20 = 45.98 N.
  3. R = √(0.36² + 45.98²) ≈ 46.0 N, and tan α = 45.98/0.36, so α ≈ 89.6°.

Answer: About 46.0 N, at about 89.6° to the x-axis (almost straight up)

Example: Forces of 10 N, 20 N and 30 N act at a point at 0°, 90° and 180°. Find the resultant.

  1. ΣFx = 10 − 30 = −20 N, and ΣFy = 20 N.
  2. R = √(400 + 400) ≈ 28.3 N. ΣFx is negative and ΣFy positive, so it points up and to the left.

Answer: About 28.3 N, at 135° to the x-axis

A force is a push or pull with magnitude, direction and point of application. Coplanar concurrent forces act in one plane through one point, and they can be combined by the parallelogram, triangle or polygon laws or by resolving along two axes. The principle of transmissibility allows a force to slide along its line of action. Bow’s notation labels spaces for graphical work.

  • Resolve: Fx = F cos θ, Fy = F sin θ.
  • R = √(ΣFx² + ΣFy²); tan α = ΣFy/ΣFx.
  • Space diagram shows the forces; a vector diagram adds them.
  • SI unit: newton.

Key formulas

  • R² = P² + Q² + 2PQ cos θ
  • R = √(ΣFx² + ΣFy²)
  • tan α = ΣFy/ΣFx

Practice questions

Two forces of 3 N and 4 N at 90° have a resultant of

  1. 5 N
  2. 7 N
  3. 1 N
  4. 12 N
Show the answer

Answer: A. 5 N √(9 + 16).

The resultant of two equal forces at 180° is

  1. 0
  2. 2F
  3. F
  4. √2 F
Show the answer

Answer: A. 0 They cancel.

Transmissibility lets a force move

  1. along its line of action
  2. anywhere
  3. perpendicular to itself
  4. in a circle
Show the answer

Answer: A. along its line of action Effect on a rigid body is unchanged.

The SI unit of force is

  1. newton
  2. pascal
  3. joule
  4. watt
Show the answer

Answer: A. newton Definition.

Concurrent forces

  1. meet at a point
  2. are parallel
  3. never meet
  4. are always equal
Show the answer

Answer: A. meet at a point Definition.

Theory questions

State the parallelogram law of forces. (2 marks)

Show the model answer

If two forces at a point are represented by adjacent sides of a parallelogram, the diagonal through that point represents the resultant.

Forces 10 N, 20 N and 30 N act at a point at 0°, 90° and 180°. Find the resultant. (8 marks)

Show the model answer

ΣFx = 10 − 30 = −20 N; ΣFy = 20 N. R = √(400 + 400) ≈ 28.3 N. tan α = 20/20 with Fx negative, so it acts at 135° from the 10 N direction.

Unit I: Moments and couples

Topics: Moment, Varignon’s theorem, lever and couple.

Moment of a force, and Varignon’s theorem

A force can turn a body as well as push it. The turning effect about a point is the moment: the force times the perpendicular distance from the point to the force’s line of action. The perpendicular distance matters, not the distance to where the force happens to be applied. The SI unit is the newton metre (N m).

Moments are given a sense, clockwise or anticlockwise, and taken with opposite signs. A lever balances when the clockwise moments about its pivot equal the anticlockwise moments, which is the law of moments. That is why a long spanner needs less force: the longer arm gives the same moment with a smaller push.

Varignon’s theorem says that the moment of the resultant of several forces about any point equals the sum of the moments of the forces themselves. In practice, it lets you resolve a slanting force into easy components and add their moments, instead of finding an awkward perpendicular distance.

  • M = F × d, with d perpendicular to the line of action
  • Unit: N m (or kN m)
  • Law of moments: Σ clockwise = Σ anticlockwise
  • Varignon: moment of R = sum of moments of the parts
  • Lever: effort × effort arm = load × load arm

Example: A 25 cm spanner is pushed at its end with 80 N, at right angles. Find the moment on the nut.

  1. d = 0.25 m.
  2. M = 80 × 0.25.

Answer: 20 N m

Example: A 100 N force acts at the end of a 2 m horizontal bar, at 30° to the bar. Find its moment about the other end, in two ways.

  1. Perpendicular distance = 2 sin 30° = 1 m, so M = 100 × 1 = 100 N m.
  2. By Varignon: the component along the bar has no moment; the perpendicular component is 100 sin 30° = 50 N, at 2 m.
  3. 50 × 2 = 100 N m.

Answer: 100 N m, both ways

Example: A lever has its load of 600 N at 0.8 m from the pivot. Where must a 240 N effort act on the other side?

  1. Moments: 240 × x = 600 × 0.8 = 480.
  2. x = 480/240.

Answer: 2 m from the pivot

Couples and parallel forces

A couple is a pair of equal, opposite, parallel forces that do not share a line of action. Their resultant force is zero, so a couple cannot move a body along, but it does turn it. Its moment is one force times the perpendicular distance between them, the arm, and that moment is the same about every point in the plane.

A couple can only be balanced by another couple of equal and opposite moment, never by a single force. Turning a tap, a steering wheel or a key are everyday couples. For parallel forces that are not a couple, the resultant is their algebraic sum, and Varignon’s theorem gives its position: the moment of the resultant must equal the sum of the moments.

  • Couple moment = F × arm
  • Resultant force of a couple = 0
  • A couple is balanced only by an opposite couple
  • Parallel forces: R = ΣF, and x̄ = ΣFx/ΣF

Example: A steering wheel 40 cm across is turned by two 20 N forces at opposite ends of a diameter. Find the couple.

  1. The arm is the diameter, 0.4 m.
  2. M = 20 × 0.4.

Answer: 8 N m

Example: Can a single force balance a couple of 15 N m? Explain.

  1. A single force has a non-zero resultant, so it would push the body along.
  2. Balance needs zero net force and zero net moment, so only an opposite 15 N m couple works.

Answer: No: only a couple of 15 N m in the opposite sense

A moment is the turning effect of a force: force times perpendicular distance from the point. Varignon’s theorem says the moment of a resultant equals the sum of the moments of its components. A couple is two equal, opposite, parallel forces, which produce pure rotation. Moments are used in levers and to find a parallel force system’s resultant.

  • Clockwise and anticlockwise moments have opposite signs.
  • Couple moment = F × arm, the same about any point.
  • A couple cannot be balanced by a single force.
  • Lever: effort × effort arm = load × load arm.

Key formulas

  • M = F × d
  • Couple M = F × a
  • E × a = W × b

Practice questions

Moment equals

  1. force × perpendicular distance
  2. force/distance
  3. mass × velocity
  4. force + distance
Show the answer

Answer: A. force × perpendicular distance Definition.

The SI unit of moment is

  1. N m
  2. N
  3. N/m
  4. J/s
Show the answer

Answer: A. N m Force × distance.

A couple produces

  1. pure rotation
  2. pure translation
  3. no effect
  4. only heat
Show the answer

Answer: A. pure rotation Net force is zero.

Varignon’s theorem is about

  1. moments
  2. friction
  3. heat
  4. centroids only
Show the answer

Answer: A. moments Law of moments.

A 10 N force at 2 m has a moment of

  1. 20 N m
  2. 5 N m
  3. 12 N m
  4. 8 N m
Show the answer

Answer: A. 20 N m 10 × 2.

Theory questions

State Varignon’s theorem. (2 marks)

Show the model answer

The moment of the resultant of a system of forces about any point equals the algebraic sum of the moments of the forces about the same point.

A lever has a 2 m effort arm and a 0.5 m load arm. Find the effort for a 1000 N load. (3 marks)

Show the model answer

E × 2 = 1000 × 0.5, so E = 250 N.

What is a couple? Give its properties and two practical examples. (8 marks)

Show the model answer

Two equal, opposite, parallel forces separated by a distance. Its moment is F × a, the same about any point, and it produces rotation with no translation. It cannot be balanced by a single force. Examples: turning a tap handle and a steering wheel.

Unit II: Equilibrium

Topics: Free body diagram, equilibrant, conditions of equilibrium, two-, three- and four-force principles, Lami’s theorem.

Conditions of equilibrium and Lami’s theorem

A body is in equilibrium when it has no tendency to move along or to turn. For a coplanar system that means three conditions: ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. For forces through a single point the moment condition is automatic, so the first two are enough.

The single force that would balance a system is its equilibrant: equal in size to the resultant, on the same line, but opposite in direction. Two forces are in equilibrium only if they are equal, opposite and collinear. Three non-parallel forces in equilibrium must all pass through one point, and drawn head to tail they form a closed triangle.

Lami’s theorem handles three concurrent forces in equilibrium neatly: each force is proportional to the sine of the angle between the other two. Measure each angle between the forces themselves, as they act at the point, not between strings and a wall. In the diagram, as the strings get flatter their tension rises steeply, which is why washing lines sag.

  • ΣFx = 0, ΣFy = 0, ΣM = 0
  • Equilibrant = resultant reversed
  • Two forces: equal, opposite, collinear
  • Three forces: concurrent, and they close a triangle
  • Lami: P/sin α = Q/sin β = R/sin γ, each angle opposite its force

Example: A 100 N lamp hangs from two strings, each at 30° to the horizontal. Find the tension.

  1. Horizontal parts cancel, by symmetry. Vertically: 2T sin 30° = 100.
  2. T = 100/(2 × 0.5).

Answer: 100 N in each string

Example: A 200 N weight hangs from two strings at 45° and 30° to the horizontal, on opposite sides. Find the tensions.

  1. Horizontal: T₁ cos 45° = T₂ cos 30°, so T₁ = 1.2247 T₂.
  2. Vertical: T₁ sin 45° + T₂ sin 30° = 200, so 0.866 T₂ + 0.5 T₂ = 200, giving T₂ = 146.4 N.
  3. T₁ = 1.2247 × 146.4 = 179.3 N. Lami checks it: 179.3/sin 120° = 146.4/sin 135° = 200/sin 105° ≈ 207.

Answer: 179.3 N in the 45° string, and 146.4 N in the 30° string

Free body diagrams

A free body diagram isolates one body and draws every force acting on it: its weight, every reaction from a support or surface, every tension and every applied load. Leave out forces the body exerts on other things. A wrong or missing force here makes every later step wrong, so this is the most important step.

A smooth surface gives a reaction perpendicular to itself. A string pulls along its own length, away from the body. A roller support pushes at right angles to its surface; a hinge can push in any direction, so it gives two components. Choose axes along and across a slope when the body sits on one, so that most forces have only one component.

  • Show weight, reactions, tensions and loads
  • Smooth surface: reaction normal to it
  • String: tension along it, pulling away
  • Hinge: two components; roller: one
  • Pick axes to suit the problem

Example: A 500 N block hangs from a single rope. A horizontal force pulls it until the rope makes 30° with the vertical. Find the force and the tension.

  1. Vertical: T cos 30° = 500, so T = 577.4 N.
  2. Horizontal: P = T sin 30° = 288.7 N.

Answer: P ≈ 288.7 N, and T ≈ 577.4 N

Example: Name the forces on a ladder resting on a rough floor against a smooth wall.

  1. Its weight, acting at its middle.
  2. At the floor: a normal reaction upward and friction along the floor. At the smooth wall: a normal reaction only, horizontal.

Answer: Weight, floor reaction, floor friction and wall reaction

A body is in equilibrium when the resultant force and the resultant moment are both zero. A free body diagram isolates the body and shows every force on it. The equilibrant is equal and opposite to the resultant. For three concurrent forces in equilibrium, Lami’s theorem says each force is proportional to the sine of the angle between the other two.

  • ΣFx = 0, ΣFy = 0, ΣM = 0.
  • Two-force principle: equal, opposite and collinear.
  • Three non-parallel forces in equilibrium are concurrent.
  • Always mark weights and reactions on the diagram.

Key formulas

  • ΣFx = 0, ΣFy = 0, ΣM = 0
  • P/sin α = Q/sin β = R/sin γ

Practice questions

Equilibrium needs

  1. zero resultant force and moment
  2. zero weight
  3. motion
  4. friction
Show the answer

Answer: A. zero resultant force and moment Definition.

Lami’s theorem applies to

  1. three concurrent forces
  2. four parallel forces
  3. friction only
  4. beams only
Show the answer

Answer: A. three concurrent forces Definition.

The equilibrant is

  1. opposite to the resultant
  2. equal to weight always
  3. always zero
  4. same direction as the resultant
Show the answer

Answer: A. opposite to the resultant Definition.

A free body diagram shows

  1. all forces on the body
  2. only weight
  3. the cost
  4. the material
Show the answer

Answer: A. all forces on the body Definition.

Theory questions

State Lami’s theorem. (2 marks)

Show the model answer

If three concurrent forces keep a body in equilibrium, each is proportional to the sine of the angle between the other two.

A 100 N lamp hangs by two strings, each at 30° to the horizontal. Find the tension. (8 marks)

Show the model answer

Vertical balance: 2T sin 30° = 100, so T = 100 N. Each string carries 100 N. Lami’s theorem gives the same result: T/sin 120° = 100/sin 120°.

Unit III: Beams

Topics: Types of beam, support and load; determinate beams; reactions by analytical and graphical methods.

Beams, supports and loads

A beam is a long member that carries loads across its supports, mainly by bending. A simply supported beam rests on supports at its two ends; a cantilever is fixed at one end and free at the other; an overhanging beam extends past a support; a fixed beam is fixed at both ends; a continuous beam rests on more than two supports.

Supports differ in what they can provide. A roller gives one reaction, at right angles to its surface. A hinge (pin) gives a reaction in any direction, so two components. A fixed support resists any movement or turning, so it gives two force components and a moment. Loads may be point loads, uniformly distributed loads (UDL, in kN/m), or uniformly varying loads.

If the equations of equilibrium alone can find all the reactions, the beam is statically determinate. For a beam in a plane there are three equations, so it can have at most three unknown reaction components. The diagram moves a single load along a simple beam: the nearer support always carries the larger share.

  • Roller: 1 reaction. Hinge: 2. Fixed: 2 forces and a moment
  • UDL w over length L acts as wL at its middle
  • Varying load (zero to w): total wL/2, at L/3 from the larger end
  • Determinate: unknown reactions ≤ 3
  • Check: sum of reactions = total load

Example: A 6 m simply supported beam carries 12 kN at 2 m from A. Find the reactions.

  1. Moments about A: R_B × 6 = 12 × 2, so R_B = 4 kN.
  2. Vertical forces: R_A = 12 − 4.

Answer: R_A = 8 kN, and R_B = 4 kN

Example: A 5 m simply supported beam carries a UDL of 2 kN/m on its whole span and 10 kN at 2 m from A. Find the reactions.

  1. The UDL is 10 kN acting at 2.5 m.
  2. Moments about A: 5R_B = 10 × 2.5 + 10 × 2 = 45, so R_B = 9 kN.
  3. R_A = 20 − 9.

Answer: R_A = 11 kN, and R_B = 9 kN

Example: A 3 m cantilever carries 5 kN at its free end. Find the reaction and the fixing moment.

  1. Vertical: R = 5 kN.
  2. Moment at the wall: 5 × 3.

Answer: R = 5 kN, and M = 15 kN m

Overhanging beams

When a load sits on an overhang, beyond a support, it tends to lift the far end of the beam, like a see-saw. The support nearer the load can then carry more than the load itself, and the other support may need to pull down. Take moments about one support to find the other reaction, then resolve vertically.

Do not guess the direction of a reaction. Assume it acts upward, solve, and read the sign: a negative answer simply means it acts downward. Always finish with a check, such as taking moments about the other support.

  • Take moments about one support first
  • Assume reactions upward; a minus sign means downward
  • Check with moments about the other support

Example: A beam has supports at A (0 m) and B (5 m), and an overhang to C (6 m). It carries 10 kN at 2 m and 4 kN at C. Find the reactions.

  1. Moments about A: 5R_B = 10 × 2 + 4 × 6 = 44, so R_B = 8.8 kN.
  2. R_A = 14 − 8.8 = 5.2 kN.
  3. Check about B: 5R_A = 10 × 3 − 4 × 1 = 26, so R_A = 5.2 kN.

Answer: R_A = 5.2 kN, and R_B = 8.8 kN

Example: In the worked overhang above, what would happen if support A were a simple roller resting on the floor?

  1. A must pull down with 6 kN.
  2. A roller resting on a surface can only push, so it cannot pull down.

Answer: The beam would tip about B: A must be anchored

A beam carries loads across supports. Beams may be simply supported, cantilever, propped, fixed, continuous or overhanging. Supports may be simple, roller, hinged or fixed. Loads may be point, uniformly distributed or uniformly varying. Reactions are found from the equilibrium equations: take moments about one support and resolve vertically.

  • A UDL acts as a point load at the middle of its length.
  • A roller gives one reaction; a hinge gives two; a fixed end gives three.
  • A statically determinate beam can be solved by equilibrium alone.
  • Check: the sum of reactions equals total load.

Key formulas

  • ΣV = 0, ΣM = 0
  • UDL resultant = w × L
  • Central load: R_A = R_B = W/2

Practice questions

A roller support provides

  1. one reaction
  2. two reactions
  3. three reactions
  4. none
Show the answer

Answer: A. one reaction Normal to the surface.

A fixed support provides

  1. three reactions
  2. one reaction
  3. no reaction
  4. only a moment
Show the answer

Answer: A. three reactions Two forces and one moment.

A UDL of 2 kN/m over 3 m is equivalent to

  1. 6 kN
  2. 2 kN
  3. 3 kN
  4. 1.5 kN
Show the answer

Answer: A. 6 kN w × L.

A cantilever is

  1. fixed at one end
  2. supported at both ends
  3. supported at the centre
  4. free at both ends
Show the answer

Answer: A. fixed at one end Definition.

A 10 kN central load on a simply supported beam gives each reaction of

  1. 5 kN
  2. 10 kN
  3. 2.5 kN
  4. 20 kN
Show the answer

Answer: A. 5 kN Symmetry.

Theory questions

Name the types of beams. (2 marks)

Show the model answer

Simply supported, cantilever, propped cantilever, fixed, continuous and overhanging.

A 6 m simply supported beam carries 10 kN at 2 m from A. Find the reactions. (5 marks)

Show the model answer

Moments about A: R_B × 6 = 10 × 2, so R_B = 3.33 kN. R_A = 10 − 3.33 = 6.67 kN.

A 5 m simply supported beam carries a UDL of 2 kN/m on the whole span and 10 kN at 2 m from A. Find the reactions. (8 marks)

Show the model answer

UDL resultant 10 kN at 2.5 m. Moments about A: 5R_B = 10 × 2 + 10 × 2.5 = 45, so R_B = 9 kN. R_A = 20 − 9 = 11 kN.

Unit III: Trusses

Topics: Plane and space trusses; assumptions; redundancy; methods of joints and sections.

Trusses and their assumptions

A truss is a framework of straight members joined at their ends to form triangles. Triangles cannot change shape without a member changing length, which makes a truss stiff and light. Roof trusses, bridges and towers use them. A plane truss lies in one plane; a space truss, like a transmission tower, is three-dimensional.

Simple analysis rests on assumptions: members are joined by frictionless pins, loads and reactions act only at the joints, and the weights of members are ignored. Then each member carries only an axial force, a pull (tension) or a push (compression), along its length.

A plane truss is perfect, just stiff with no spare members, when m = 2j − 3, where m is the number of members and j the number of joints. With fewer members it is deficient and will collapse; with more it is redundant, and equilibrium alone cannot find all the forces.

  • Perfect: m = 2j − 3
  • Deficient: m < 2j − 3. Redundant: m > 2j − 3
  • Members carry axial force only
  • Tension pulls on the joint; compression pushes
  • Simple triangle, apex load W: rafter W/(2 sin θ), tie W/(2 tan θ)

Example: A plane truss has 6 joints. How many members make it perfect?

  1. m = 2j − 3.
  2. 2 × 6 − 3.

Answer: 9 members

Example: A triangular truss with base angles of 30° carries 10 kN at its apex. Find the forces in the rafters and the tie.

  1. Each support carries 5 kN. At a support joint, vertically: F sin 30° = 5, so each rafter carries 10 kN.
  2. Horizontally: tie = 10 cos 30° = 8.66 kN.
  3. The rafters push on the joints (compression) and the tie pulls (tension).

Answer: Rafters 10 kN compression, and tie 8.66 kN tension

Example: A truss has 7 members and 5 joints. What kind is it?

  1. 2j − 3 = 7.
  2. m equals 2j − 3.

Answer: A perfect truss

Method of joints and method of sections

In the method of joints, first find the support reactions from the whole truss. Then pick a joint with no more than two unknown member forces, draw its free body, and use ΣFx = 0 and ΣFy = 0. Move on from joint to joint. Assume every unknown member is in tension; a negative answer means compression.

The method of sections finds the force in a particular member without working through the whole truss. Cut the truss through not more than three members whose forces are unknown, keep one side, and apply the three equations of equilibrium to that side. Taking moments about the point where two of the cut members meet gives the third directly.

One shortcut saves time: at a joint with no load where only two members meet at an angle, both members carry zero force. Where three members meet and two are in line, with no load, the third carries zero force.

  • Joints: start where only two unknowns meet
  • Sections: cut at most three unknown members
  • Assume tension; a minus sign means compression
  • Zero members: two non-collinear members at an unloaded joint

Example: At an unloaded joint, two members meet at 90°. What are their forces?

  1. Resolve along one member: the other has no component there, so the first force must be zero.
  2. Then the second must also be zero.

Answer: Both are zero

Example: A section cuts three members of a truss 2 m deep. Two of the cut members meet at a joint 4 m from support A, where R_A = 20 kN, with no other load on that side. Find the force in the third member.

  1. Moments about the joint where the other two meet: F × 2 = 20 × 4.
  2. F = 80/2.

Answer: 40 kN

A truss is a frame of straight members joined at their ends, loaded only at the joints, so members are in tension or compression. A plane truss is perfect when m = 2j − 3. In the method of joints, balance forces at each joint, beginning where no more than two unknowns exist. In the method of sections, cut through three members and use the equilibrium of one part.

  • Assumptions: pin joints, loads at joints, weightless members.
  • A member pulled away from the joint is in tension.
  • Fewer members than 2j − 3 means deficient; more means redundant.
  • At a joint with no load and two non-collinear members, both forces are zero.

Key formulas

  • m = 2j − 3

Practice questions

A perfect plane truss has m =

  1. 2j − 3
  2. 2j + 3
  3. j
  4. 3j
Show the answer

Answer: A. 2j − 3 Standard relation.

Truss members carry

  1. axial force
  2. bending only
  3. twisting only
  4. no force
Show the answer

Answer: A. axial force By assumption.

The method of sections cuts at most

  1. three unknown members
  2. all members
  3. one member
  4. ten members
Show the answer

Answer: A. three unknown members Three equilibrium equations.

With 5 joints, a perfect truss has

  1. 7 members
  2. 5 members
  3. 10 members
  4. 3 members
Show the answer

Answer: A. 7 members 2(5) − 3.

Theory questions

State the assumptions in the analysis of a plane truss. (3 marks)

Show the model answer

Members are straight and joined by pins, loads act only at joints, member weights are ignored, and all members carry axial force only.

Explain the method of joints with a suitable sequence of steps. (8 marks)

Show the model answer

Find the support reactions from the whole truss. Choose a joint with at most two unknown member forces. Draw its free body diagram, and apply ΣFx = 0 and ΣFy = 0. Assume tension; a negative answer means compression. Move to the next joint with two unknowns until all members are known.

Unit IV: Centroid and centre of gravity

Topics: Plane figures, composite figures, simple and composite solids.

Centroid of plane figures

The centre of gravity of a body is the point through which its whole weight acts, whichever way it is turned. The centroid is the geometric centre of a plane area, and for a uniform thin plate the two coincide. If a figure has an axis of symmetry, its centroid lies on that axis, and with two axes it is where they cross.

For a composite figure, split it into simple shapes whose centroids you know. Choose one reference axis for all the parts. Then x̄ = ΣAx/ΣA and ȳ = ΣAy/ΣA, which is Varignon’s idea applied to areas: the moment of the whole area equals the sum of the moments of the parts.

A hole is treated as a negative area: subtract its area and its moment. Measure every distance from the same axis, including the hole’s. The diagram widens the flange of a T-section, and the centroid rises towards it.

  • Rectangle: at its centre
  • Triangle: h/3 from the base
  • Semicircle: 4r/(3π) from the diameter
  • Quarter circle: 4r/(3π) from each straight edge
  • x̄ = ΣAx/ΣA, ȳ = ΣAy/ΣA
  • Holes: negative area

Example: Find the centroid of a T-section with a 100 × 20 mm flange on a 20 × 100 mm web, measured from the bottom of the web.

  1. Web: A = 2000 mm², at y = 50 mm. Flange: A = 2000 mm², at y = 110 mm.
  2. ȳ = (2000 × 50 + 2000 × 110)/4000.

Answer: 80 mm from the bottom, on the axis of symmetry

Example: A 200 × 100 mm plate has a hole of 50 mm diameter centred at (50, 50) mm. Find x̄ from the left edge.

  1. Plate: A = 20 000 mm² at x = 100. Hole: A = π × 25² = 1963.5 mm² at x = 50.
  2. x̄ = (20 000 × 100 − 1963.5 × 50)/(20 000 − 1963.5).
  3. = 1 901 825/18 036.5.

Answer: About 105.4 mm; ȳ stays 50 mm by symmetry

Example: Find the centroid of a semicircle of radius 60 mm from its diameter.

  1. ȳ = 4r/(3π).
  2. = 240/(3π).

Answer: About 25.5 mm

Centre of gravity of solids

For solids of one material, the centre of gravity is found the same way with volumes instead of areas: x̄ = ΣVx/ΣV. A few standard results are worth knowing by heart, each measured from the base of the solid.

The CG of a solid cone is a quarter of its height above the base, and that of a solid hemisphere 3r/8 above its flat face. A low centre of gravity makes a body more stable, which is why loaded trucks keep heavy goods low.

  • Solid cone: h/4 from the base
  • Solid hemisphere: 3r/8 from the flat face
  • Cylinder: at mid-height
  • x̄ = ΣVx/ΣV for one material
  • Lower CG: more stable

Example: Find the CG of a solid cone 120 mm high.

  1. ȳ = h/4 from the base.
  2. 120/4.

Answer: 30 mm above the base

Example: Find the CG of a solid hemisphere of radius 40 mm.

  1. ȳ = 3r/8 from the flat face.
  2. 3 × 40/8.

Answer: 15 mm from the flat face

The centre of gravity is the point through which a body’s weight acts, and the centroid is the geometric centre of an area. Symmetrical shapes have their centroid on the axis of symmetry. For a composite figure, split it into simple shapes and use the moments of area, treating a hole as a negative area.

  • Rectangle: at the mid-point. Triangle: h/3 from the base.
  • Semicircle: 4r/3π from the diameter.
  • Solid cone: h/4 from the base. Hemisphere: 3r/8 from the base.
  • Use one reference axis for all parts.

Key formulas

  • x̄ = ΣAx/ΣA
  • ȳ = ΣAy/ΣA

Practice questions

The centroid of a triangle is from the base at

  1. h/3
  2. h/2
  3. 2h/3
  4. h/4
Show the answer

Answer: A. h/3 Standard.

The centroid of a semicircle is from the diameter at

  1. 4r/3π
  2. r/2
  3. r/3
  4. 2r/π
Show the answer

Answer: A. 4r/3π Standard.

A hole is treated as

  1. negative area
  2. positive area
  3. zero
  4. a mass
Show the answer

Answer: A. negative area It is subtracted.

The CG of a solid cone is from the base at

  1. h/4
  2. h/3
  3. h/2
  4. 3h/4
Show the answer

Answer: A. h/4 Standard.

Theory questions

Distinguish between centre of gravity and centroid. (2 marks)

Show the model answer

The centre of gravity is the point where the total weight of a body acts. The centroid is the geometric centre of a plane figure.

Find the centroid of a T-section with a 100 × 20 mm flange on a 20 × 100 mm web, from the bottom. (8 marks)

Show the model answer

Web: A = 2000 mm², y = 50 mm. Flange: A = 2000 mm², y = 110 mm. ȳ = (2000 × 50 + 2000 × 110)/4000 = 80 mm from the bottom, on the axis of symmetry.

Unit IV: Moment of inertia

Topics: General formula, section modulus, radius of gyration, parallel and perpendicular axes, composite sections.

Moment of inertia of areas

The moment of inertia of an area about an axis, I = Σ(A y²), measures how far the area is spread from that axis. Because the distance is squared, area far from the axis counts for much more than area near it. Its unit is length to the fourth power, such as mm⁴. In beams, a larger I means a stiffer beam that bends less.

For a rectangle of breadth b and depth d about its own centroidal axis parallel to b, I = bd³/12. Depth appears cubed, so a plank on edge is far stiffer than the same plank laid flat, as the diagram shows. This is why floor joists and steel I-sections are deep, with most of their material far from the middle.

The radius of gyration k is the distance from the axis at which the whole area could be concentrated without changing I, so I = Ak². The section modulus Z = I/y_max links I to bending strength: the larger Z is, the smaller the bending stress for a given moment.

  • Rectangle about its centroid: bd³/12. About its base: bd³/3
  • Triangle about its centroid: bh³/36. About its base: bh³/12
  • Circle about a diameter: πd⁴/64
  • Hollow circle: π(D⁴ − d⁴)/64
  • I = Ak², k = √(I/A)
  • Z = I/y_max

Example: Find I for a 100 × 200 mm rectangle about its centroidal axis parallel to the 100 mm side, and its radius of gyration.

  1. I = bd³/12 = 100 × 200³/12 = 6.667 × 10⁷ mm⁴.
  2. k = √(I/A) = √(6.667 × 10⁷/20 000).

Answer: I ≈ 6.67 × 10⁷ mm⁴, and k ≈ 57.7 mm

Example: How much stiffer is a 50 × 200 mm plank on edge than laid flat?

  1. On edge: 50 × 200³/12 = 3.333 × 10⁷ mm⁴. Flat: 200 × 50³/12 = 2.083 × 10⁶ mm⁴.
  2. Ratio = (200/50)².

Answer: 16 times

Example: Find I about a diameter for a hollow shaft, 100 mm outside and 80 mm inside.

  1. I = π(D⁴ − d⁴)/64 = π(10⁸ − 4.096 × 10⁷)/64.
  2. = π × 5.904 × 10⁷/64.

Answer: About 2.90 × 10⁶ mm⁴

Parallel and perpendicular axis theorems

The parallel axis theorem moves I from a centroidal axis to any parallel axis: I_AB = I_G + Ah², where h is the distance between the axes. It is the key to composite sections: find each part’s own I_G, shift it to the common axis with Ah², and add.

The perpendicular axis theorem applies to a flat area: the moment of inertia about an axis perpendicular to the plane equals the sum of the moments about two perpendicular axes in the plane that cross at the same point, I_z = I_x + I_y. For a circle it gives the polar moment, πd⁴/32, used for shafts in twisting.

  • I_AB = I_G + Ah²
  • I_z = I_x + I_y (plane areas)
  • Circle: polar I = πd⁴/32
  • Composite: find I_G of each part, then shift and add

Example: Use the parallel axis theorem to find I of a 100 × 200 mm rectangle about its 100 mm base.

  1. I_G = 6.667 × 10⁷ mm⁴, A = 20 000 mm², and h = 100 mm.
  2. I = 6.667 × 10⁷ + 20 000 × 100² = 6.667 × 10⁷ + 2 × 10⁸.

Answer: 2.667 × 10⁸ mm⁴, the same as bd³/3

Example: Find the polar moment of inertia of a circle 100 mm across.

  1. About a diameter: π × 100⁴/64 = 4.909 × 10⁶ mm⁴.
  2. Polar = sum of two diameters: 2 × 4.909 × 10⁶.

Answer: About 9.82 × 10⁶ mm⁴

Moment of inertia of an area, I = Σ(Ay²), measures how the area is spread about an axis, and it governs bending. The radius of gyration k is the distance at which the whole area could be concentrated for the same I. The parallel axis theorem moves I to another axis, and the perpendicular axis theorem links axes in a plane to one normal to it. Section modulus Z = I/y.

  • Rectangle about centroid: bd³/12.
  • Circle: πd⁴/64.
  • Triangle about centroid: bh³/36.
  • A larger depth gives a much larger I, so beams are deep.

Key formulas

  • I = Ak²
  • I_AB = I_G + Ah²
  • I_z = I_x + I_y
  • Z = I/y
  • I_rect = bd³/12
  • I_circle = πd⁴/64

Practice questions

The MI of a rectangle about its centroid is

  1. bd³/12
  2. bd³/3
  3. bd²/6
  4. bd/12
Show the answer

Answer: A. bd³/12 Standard.

The unit of area MI is

  1. m⁴
  2. m²
  3. m³
  4. kg m²
Show the answer

Answer: A. m⁴ Area × distance².

The parallel axis theorem is

  1. I_G + Ah²
  2. I_G − A
  3. A/h
  4. I/y
Show the answer

Answer: A. I_G + Ah² Definition.

Section modulus is

  1. I/y
  2. I × y
  3. A/y
  4. y/I
Show the answer

Answer: A. I/y Definition.

The MI of a circle about its diameter is

  1. πd⁴/64
  2. πd⁴/32
  3. πd²/4
  4. πd³/32
Show the answer

Answer: A. πd⁴/64 Standard.

Theory questions

Define the radius of gyration. (2 marks)

Show the model answer

k = √(I/A): the distance from an axis at which the whole area could be concentrated without changing I.

Find the MI of a 100 × 200 mm rectangle about its centroidal axis parallel to the shorter side. (3 marks)

Show the model answer

I = bd³/12 = 100 × 200³/12 ≈ 6.67 × 10⁷ mm⁴.

State the parallel and perpendicular axis theorems. Find the MI of the same rectangle about its base. (8 marks)

Show the model answer

Parallel: I_AB = I_G + Ah². Perpendicular: I_z = I_x + I_y. About the base: I = 6.67 × 10⁷ + (20000)(100²) = 2.67 × 10⁸ mm⁴, which equals bd³/3.

Unit V: Friction

Topics: Coulomb’s laws, limiting friction, coefficient, angle of friction and repose, cone of friction; level and inclined planes; ladder and wedge.

Laws of friction

Friction is the force between two surfaces in contact that opposes their sliding over each other. As a push on a resting block grows, friction grows to match it, until it reaches a maximum, the limiting friction. Beyond that the block moves, and the friction drops slightly to its kinetic value.

Coulomb’s laws describe dry friction. Friction always opposes the relative motion, or the tendency to move. The limiting friction is proportional to the normal reaction, F = μN, where μ is the coefficient of friction. It depends on the nature of the surfaces, but not on the area of contact. Kinetic friction is a little less than limiting friction.

Friction is useful in walking, brakes, belts, and in nuts and bolts staying tight. It is harmful when it wears parts and wastes energy as heat, which is why machines are lubricated.

  • F_lim = μN
  • μ = tan φ, where φ is the angle of friction
  • Angle of repose = angle of friction
  • Kinetic friction < limiting friction
  • Independent of area of contact

Example: A 100 N block rests on a level floor with μ = 0.3. What horizontal force just moves it?

  1. N = 100 N.
  2. F = μN = 0.3 × 100.

Answer: 30 N

Example: A block just starts to slide when a plank is tilted to 21.8°. Find μ.

  1. At the point of sliding, the angle is the angle of repose, which equals φ.
  2. μ = tan 21.8°.

Answer: μ ≈ 0.40

Inclined planes, cone of friction and wedges

On a slope at θ, the weight W splits into W sin θ along the slope and W cos θ into it. So N = W cos θ, and limiting friction is μW cos θ. A block stays put without help while tan θ ≤ μ. When it is about to move up, friction acts down the slope; about to move down, friction acts up it.

If the total reaction, the resultant of N and friction, is swung round the normal at the angle of friction φ, it sweeps out a cone: the cone of friction. A body stays at rest as long as the resultant of the applied forces lies inside it.

A wedge is a tapered block driven in to lift or split a load, with friction on its faces. Solving a wedge means drawing a free body for the wedge and one for the load, with friction on each contact face opposing the motion, and using equilibrium for both.

  • N = W cos θ, along the slope: W sin θ
  • Moving up: P = W sin θ + μW cos θ (push parallel)
  • Holding it from sliding down: P = W sin θ − μW cos θ
  • Self-holding if tan θ ≤ μ
  • Cone of friction: semi-angle φ

Example: The same 200 N block on the 30° slope with μ = 0.25: what force parallel to the slope stops it sliding down?

  1. tan 30° = 0.577 > 0.25, so it would slide by itself.
  2. Friction now acts up the slope: P = 100 − 43.3.

Answer: 56.7 N, up the slope

Example: A 5 m ladder weighing 200 N stands on a rough floor against a smooth wall, at 60° to the floor. Find the least μ at the floor.

  1. Moments about the foot: R_wall × 5 sin 60° = 200 × 2.5 cos 60°, so R_wall = 57.7 N.
  2. Horizontally, friction F = R_wall = 57.7 N; vertically, N = 200 N.
  3. μ = F/N = 57.7/200.

Answer: μ ≈ 0.29

Friction opposes relative motion between surfaces. Limiting friction, F = μN, is the greatest static friction. Coulomb’s laws say it is proportional to the normal reaction and independent of area. The angle of friction satisfies tan φ = μ, and the angle of repose of a block on an incline equals φ. Ladder and wedge problems combine friction with equilibrium.

  • Kinetic friction is slightly lower than limiting friction.
  • Useful: walking, brakes and belts. Harmful: wear and heat.
  • On an incline: F = W sin θ, N = W cos θ.
  • Lubrication reduces friction.

Key formulas

  • F = μN
  • μ = tan φ
  • N = W cos θ on an incline

Practice questions

Limiting friction equals

  1. μN
  2. μ/N
  3. N/μ
  4. μ + N
Show the answer

Answer: A. μN Definition.

μ = tan of the

  1. angle of friction
  2. angle of incidence
  3. right angle
  4. dip
Show the answer

Answer: A. angle of friction Definition.

Friction does not depend on

  1. the area of contact
  2. the normal reaction
  3. the surface type
  4. μ
Show the answer

Answer: A. the area of contact Coulomb’s law.

If W = 100 N and μ = 0.3, the limiting friction is

  1. 30 N
  2. 100 N
  3. 3 N
  4. 300 N
Show the answer

Answer: A. 30 N μW on a level plane.

Kinetic friction is

  1. less than limiting
  2. more than limiting
  3. always zero
  4. infinite
Show the answer

Answer: A. less than limiting Generally.

Theory questions

State Coulomb’s laws of friction. (3 marks)

Show the model answer

Friction opposes motion, is proportional to the normal reaction up to the limit, depends on the surfaces, and is independent of the contact area.

A 200 N block rests on a plane at 30°. Find the force parallel to the plane needed to push it up if μ = 0.25. (8 marks)

Show the model answer

N = 200 cos 30° = 173.2 N, F = 43.3 N. P = 200 sin 30° + 43.3 = 143.3 N.

Unit VI: Lifting machines

Topics: Simple and compound machines, law of a machine, simple lifting machines.

M.A., V.R. and efficiency

A lifting machine lets a small effort P raise a large load W. Its mechanical advantage is M.A. = W/P. Its velocity ratio is V.R. = distance moved by the effort/distance moved by the load in the same time, which depends only on the machine’s geometry. Efficiency is the work output over the work input, which works out as η = M.A./V.R.

In an ideal machine with no friction, η = 1, so the ideal effort is W/V.R. The real effort is larger; the difference, P − W/V.R., is the effort lost in friction. A compound machine combines simple ones, and its V.R. is the product of theirs.

If a machine’s efficiency is above 50%, it is reversible: on removing the effort, the load runs back down by itself. If it is 50% or less, it is self-locking, which is what you want in a screw jack holding up a car.

  • M.A. = W/P
  • V.R. = effort distance/load distance
  • η = M.A./V.R.
  • Ideal effort = W/V.R.; lost in friction = P − W/V.R.
  • Reversible if η > 50%; self-locking if η ≤ 50%

Example: A machine of V.R. 20 lifts 1000 N with an effort of 80 N. Find M.A., efficiency and the effort lost in friction. Is it reversible?

  1. M.A. = 1000/80 = 12.5, and η = 12.5/20 = 62.5%.
  2. Ideal effort = 1000/20 = 50 N, so 30 N is lost in friction.
  3. η > 50%.

Answer: M.A. 12.5, η = 62.5%, 30 N lost; it is reversible

Example: In a machine of V.R. 20, efforts of 50 N and 90 N lift 500 N and 1000 N. Find the law of the machine, and its maximum M.A. and efficiency.

  1. m = (90 − 50)/(1000 − 500) = 0.08, and c = 50 − 0.08 × 500 = 10. So P = 0.08W + 10.
  2. Maximum M.A. = 1/m = 12.5.
  3. Maximum η = 1/(m × V.R.) = 1/1.6.

Answer: P = 0.08W + 10; max M.A. 12.5; max η = 62.5%

Wheel and axle, and the screw jack

In a simple wheel and axle, the effort rope is wound on a wheel of diameter D and the load rope on an axle of diameter d, so V.R. = D/d. A differential wheel and axle has an axle with two diameters, d₁ and d₂: the load rope winds on one and off the other, so the load rises only by the difference, giving V.R. = 2D/(d₁ − d₂), a large ratio from a compact machine.

A screw jack lifts a load with a screw of pitch p turned by a lever of length L. One turn moves the effort 2πL and lifts the load one pitch (for a single-start thread), so V.R. = 2πL/p. Screw jacks have a large V.R. and, because their efficiency is usually below 50%, they are self-locking.

  • Wheel and axle: V.R. = D/d
  • Differential wheel and axle: V.R. = 2D/(d₁ − d₂)
  • Screw jack: V.R. = 2πL/p
  • Law of the machine: P = mW + c
  • Max M.A. = 1/m; max η = 1/(m × V.R.)

Example: A wheel of 400 mm diameter and axle of 100 mm diameter lift 400 N with 125 N. Find V.R., M.A. and efficiency.

  1. V.R. = 400/100 = 4, and M.A. = 400/125 = 3.2.
  2. η = 3.2/4.

Answer: V.R. 4, M.A. 3.2, η = 80%

Example: A differential wheel and axle has D = 300 mm, d₁ = 100 mm and d₂ = 80 mm. Find its V.R.

  1. V.R. = 2D/(d₁ − d₂).
  2. = 600/20.

Answer: 30

A lifting machine lifts a heavy load W using a smaller effort P. Mechanical advantage is W/P, velocity ratio is the distance moved by effort per distance moved by load, and efficiency is their ratio. The law of a machine is linear: P = mW + c. A machine is reversible if its efficiency exceeds 50%; below that it is self-locking. Examples include wheel and axle, differential wheel and axle, and screw jack.

  • Ideal effort = W/V.R.; friction effort = P − W/V.R.
  • Simple wheel and axle: V.R. = D/d.
  • Differential wheel and axle: V.R. = 2D/(d₁ − d₂).
  • Screw jack: V.R. = 2πL/p.

Key formulas

  • η = (M.A./V.R.) × 100%
  • P = mW + c
  • V.R. = 2πL/p (screw jack)

Practice questions

Efficiency equals

  1. M.A./V.R.
  2. V.R./M.A.
  3. M.A. × V.R.
  4. W × P
Show the answer

Answer: A. M.A./V.R. Definition.

A machine is self-locking if efficiency is

  1. below 50%
  2. above 50%
  3. 100%
  4. exactly 75%
Show the answer

Answer: A. below 50% Standard result.

With W = 500 N and P = 50 N, M.A. is

  1. 10
  2. 5
  3. 50
  4. 450
Show the answer

Answer: A. 10 W/P.

The law of a machine is

  1. P = mW + c
  2. P = W²
  3. W = 1/P
  4. P = c/W
Show the answer

Answer: A. P = mW + c Linear.

A screw jack’s V.R. is

  1. 2πL/p
  2. p/L
  3. πD
  4. L/p²
Show the answer

Answer: A. 2πL/p One turn raises the load by one pitch.

Theory questions

Define M.A., V.R. and efficiency. (2 marks)

Show the model answer

M.A. = load/effort. V.R. = distance moved by effort/distance moved by load. Efficiency = M.A./V.R.

A machine with V.R. = 20 lifts 1000 N with 80 N. Find its efficiency and whether it is reversible. (5 marks)

Show the model answer

M.A. = 12.5. η = 12.5/20 = 62.5%. Since it is above 50%, the machine is reversible.

In a lifting machine, efforts of 50 N and 90 N lift 500 N and 1000 N. Find the law and the effort for 800 N. (8 marks)

Show the model answer

P = mW + c: 50 = 500m + c and 90 = 1000m + c, so m = 0.08, c = 10. Law: P = 0.08W + 10. For W = 800 N, P = 74 N.

Chapters follow the SCTE Assam syllabus. The notes and questions were written for this studio and are not official.

Open this subject studio →