IITIAN1997 STUDIO

Engineering Graphics (NEP 2020)

Semester 1 · ES-101 · 33 MCQs and 16 theory questions

Open this subject studio →

Unit I: Instruments, lines, lettering, dimensioning

Topics: Drawing equipment, sheet layout, types of lines, dimensioning systems, single-stroke lettering.

Why engineers draw, and how a sheet is set out

A drawing tells a worker exactly what to make without a single spoken word. Two people who share no language can still build the same part from the same drawing, because the symbols and rules are standard. In India those rules come from the Bureau of Indian Standards, mainly SP 46.

Paper sizes are chosen so that each size is half of the one above it: A0 has an area of one square metre, A1 is half of that, and so on down to A4. Every sheet gets a border, which leaves a margin for filing, and a title block in the lower right corner. The title block holds the name, the drawing number, the scale, the date and the projection symbol, so anyone can identify the sheet at a glance.

  • A4: 210 × 297 mm
  • A3: 297 × 420 mm
  • A2: 420 × 594 mm
  • A1: 594 × 841 mm
  • A0: 841 × 1189 mm

Example: What is the ratio of the longer side to the shorter side of any A-size sheet, and why does it matter?

  1. Check A4: 297/210 = 1.414.
  2. Check A3: 420/297 = 1.414.
  3. This is √2. Halving a √2 sheet across its long side gives two sheets of the same shape.

Answer: The ratio is √2, so a drawing can be enlarged or reduced between sizes without changing its proportions.

Lines: each type has one meaning

A reader understands a drawing from its lines, so each kind of line must be used only for its proper purpose. The thick continuous line shows what you can actually see. A thin continuous line carries information about the object, such as dimensions and hatching. Short dashes show an edge hidden behind a surface, and a thin chain line marks a centre or an axis.

When lines coincide, an order of priority decides which one is drawn: a visible edge comes first, then a hidden edge, then a cutting plane, then a centre line, and last a dimension or extension line.

Example: A hole runs right through a block. In the front view, you cannot see the hole. How should it be drawn?

  1. The hole’s edges lie behind the front face, so they are hidden: use short dashes.
  2. The hole has an axis, so add one thin chain line along its centre.
  3. The outline of the block stays thick and continuous.

Answer: Two dashed lines for the hole’s edges with a chain centre line between them, inside a thick outline.

Lettering and dimensioning

Lettering is written in single-stroke capitals, in which each stroke has the thickness of the pen, because this is quick and easy to read. It may be vertical or inclined at 75° to the horizontal.

A dimension has three parts. Extension lines lead away from the object, leaving a small gap. A dimension line with arrowheads runs between them. A figure gives the size. Dimensions are in millimetres, and the unit is not written beside each number. In the aligned system, figures are read from the bottom or right side of the sheet; in the unidirectional system, all of them are read from the bottom.

  • Give each dimension once only.
  • Keep dimensions outside the views where you can.
  • Do not use an outline or a centre line as a dimension line.
  • Put smaller dimensions nearer the view so that lines do not cross.
  • Show a diameter with ⌀ and a radius with R.

A drawing is the language of engineering. Drawing instruments include the T-square, set squares, drafter, compass and scale. Sheets have standard sizes (A0 to A4) with margins and a title block. Each line type has a meaning, and lettering is single-stroke, upright or inclined. Dimensions follow Indian Standard practice, in the aligned or unidirectional system.

  • A2 measures 420 × 594 mm; each smaller size halves the area.
  • Dimensions are in mm unless stated.
  • Dimension lines end in arrowheads, and extension lines stand slightly clear of the object.
  • Avoid repeating a dimension, or dimensioning inside the view where possible.

Key formulas

  • A4: 210 × 297 mm
  • A3: 297 × 420 mm
  • A2: 420 × 594 mm

Practice questions

A hidden edge is drawn with

  1. thick continuous lines
  2. short dashes
  3. long chains
  4. wavy lines
Show the answer

Answer: B. short dashes Standard line type.

A centre line is a

  1. long chain line
  2. thick line
  3. dotted square
  4. wavy line
Show the answer

Answer: A. long chain line Long dash and short dash.

The size of A3 paper is

  1. 297 × 420 mm
  2. 210 × 297 mm
  3. 420 × 594 mm
  4. 594 × 841 mm
Show the answer

Answer: A. 297 × 420 mm Standard size.

Lettering in drawings is usually

  1. single stroke
  2. cursive
  3. decorative
  4. free style
Show the answer

Answer: A. single stroke For clarity.

Unless stated, dimensions are in

  1. mm
  2. cm
  3. m
  4. inches
Show the answer

Answer: A. mm Standard practice.

Theory questions

Name four types of lines and their uses. (3 marks)

Show the model answer

Thick continuous for outlines; short dashes for hidden edges; long chain for centre lines; thin continuous for dimension and extension lines.

Describe the aligned and unidirectional systems of dimensioning and give five general rules. (8 marks)

Show the model answer

Aligned: figures are written along the dimension line, read from the bottom or right. Unidirectional: all figures read from the bottom. Rules: use one unit; do not repeat dimensions; keep them outside the view where possible; do not cross dimension lines; don’t use outlines as dimension lines.

Unit I: Geometrical constructions and curves

Topics: Lines, angles, polygons, circles, tangents; ellipse, parabola, hyperbola, tangents and normals to conics.

Conics by the eccentricity method

A conic is the path of a point P that moves so that its distance from a fixed point (the focus, F) divided by its distance from a fixed line (the directrix) stays constant. This constant is the eccentricity, e. If e is below 1 the curve is an ellipse, if e = 1 a parabola, and if e is above 1 a hyperbola. The same construction draws all three.

First place the vertex V on the axis, dividing the distance from directrix to focus so that VF/VD = e. Then a sloping line from the directrix’s foot through a point above V gives, at any position along the axis, a height equal to e times the distance from the directrix. Use that height as a radius from F, and cut the vertical line at that position. Each pair of cuts gives two points on the curve.

Example: Draw an ellipse with the focus 50 mm from the directrix and e = 2/3. Find the position of the vertex and describe the construction.

  1. VF/VD = 2/3, and VF + VD = 50 mm.
  2. So VF = 50 × 2/5 = 20 mm and VD = 30 mm.
  3. At V, erect VE = VF = 20 mm and join D to E, extending the line. Its height at any point is 2/3 of the distance from the directrix.
  4. Mark points 1, 2, 3 … along the axis beyond V and draw verticals.
  5. With F as centre and each vertical’s height up to the sloping line as radius, cut that vertical above and below the axis.
  6. Join the points with a smooth curve.

Answer: The vertex lies 30 mm from the directrix and 20 mm from the focus.

Example: Show how to draw the tangent and normal at a point P on this conic.

  1. Join P to the focus F.
  2. At F, draw a line at 90° to PF, meeting the directrix at T.
  3. Join T to P: this is the tangent.
  4. Through P, draw a line at 90° to the tangent: this is the normal.

Answer: Tangent PT, with the normal perpendicular to it at P.

Cycloid and involute

Roll a circle along a straight line without slipping and watch one point on its rim: its path is a cycloid. In one full turn, the circle travels a distance equal to its circumference, πD, and the point rises to a height D. To draw it, divide the circle and the length πD into 12 equal parts. As the centre moves to each position, the point stands at the matching height, found by striking an arc from the new centre.

If the circle rolls on the outside of another circle the curve is an epicycloid, and on the inside it is a hypocycloid. An involute is the path of the end of a taut string unwound from a circle. Gear teeth are shaped this way because such teeth transmit motion smoothly.

  • Cycloid: base length πD, height D.
  • Involute of a circle: unwound string length after one turn = πD.
  • Epicycloid: rolls outside. Hypocycloid: rolls inside.

Example: A circle of 50 mm diameter rolls along a line. Find the base length and height of the cycloid and give the first steps of drawing it.

  1. Base length = πD = π × 50 ≈ 157 mm.
  2. Height = D = 50 mm.
  3. Draw the circle with its point P at the bottom, and a 157 mm base.
  4. Divide the circle and the base into 12 equal parts.
  5. Draw horizontals through the divisions of the circle, and find the centres C1 to C12 along the line through its centre.
  6. With centre C1 and radius 25 mm, cut horizontal 1: this is P1. Repeat for all the rest and join the points smoothly.

Answer: A curve 157 mm long and 50 mm high.

Geometrical construction uses simple instruments to bisect lines, draw angles of 30°, 45°, 60° and 90°, and construct polygons, tangents and in-circles and circum-circles. Conic curves can be drawn by general methods: the ellipse by concentric circles or the eccentricity method, with parabola and hyperbola from focus and directrix.

  • The in-circle touches all sides of a polygon; the circum-circle passes through all vertices.
  • The sum of a regular polygon’s exterior angles is 360°.
  • Eccentricity e < 1 is an ellipse, = 1 a parabola, > 1 a hyperbola.
  • A tangent and a normal to a curve are at right angles.

Key formulas

  • Interior angle = (n − 2) × 180°/n
  • e = distance from focus/distance from directrix

Practice questions

Each interior angle of a regular hexagon is

  1. 60°
  2. 90°
  3. 120°
  4. 135°
Show the answer

Answer: C. 120° (6 − 2) × 180/6.

An ellipse has eccentricity

  1. less than 1
  2. 1
  3. above 1
  4. 0 always
Show the answer

Answer: A. less than 1 Definition.

A tangent to a circle is perpendicular to the

  1. radius at the contact point
  2. chord
  3. diameter elsewhere
  4. arc
Show the answer

Answer: A. radius at the contact point Standard result.

A circum-circle of a polygon passes through

  1. the vertices
  2. the midpoints of sides
  3. the centre
  4. none
Show the answer

Answer: A. the vertices Definition.

Theory questions

Give the steps for drawing a hexagon of 30 mm side. (3 marks)

Show the model answer

Draw a circle of 30 mm radius; step off the radius six times around it; join the points in order.

Construct an ellipse with a major axis of 100 mm and a minor axis of 60 mm by the concentric circles method. Give the steps. (8 marks)

Show the model answer

Draw two concentric circles of 100 mm and 60 mm diameter. Draw radial lines at equal angles. From each intersection on the large circle, draw a vertical; from each on the small circle, draw a horizontal. Their crossings lie on the ellipse. Join them with a smooth curve.

Unit I: Scales

Topics: Representative fraction; plain and diagonal scales.

Representative fraction and the plain scale

A bridge cannot fit on a sheet and a watch part is too small to draw at its true size, so a scale changes the size in a stated ratio. The representative fraction (R.F.) is the length on the drawing divided by the actual length, with both in the same unit. So it has no unit of its own. An R.F. below 1 reduces, and an R.F. above 1 enlarges.

A plain scale reads two units, such as metres and decimetres. Its length is R.F. × the longest length to be measured. Divide it into equal main parts, place zero at the end of the first part and number to the right, then divide the first part into the smaller unit. A length is read by taking main parts to the right of zero and small parts to the left.

Example: Construct a plain scale of R.F. = 1/50 to show metres and decimetres, long enough to measure 8 m. Show 5.6 m on it.

  1. Length of scale = 8 m × 1/50 = 800 cm/50 = 16 cm.
  2. Draw a 16 cm line and divide it into 8 equal parts: each part is 1 m.
  3. Mark 0 at the end of the first part, then 1, 2, 3 … to the right.
  4. Divide the first part into 10: each small part is 1 dm.
  5. For 5.6 m, take 5 main parts to the right of 0 and 6 small parts to the left.
  6. Write “R.F. = 1/50” and the units on the scale.

Answer: A scale 16 cm long. The length 5.6 m measures 5.6 × 2 = 11.2 cm on it.

The diagonal scale

A plain scale reads only two units. To read a third, a diagonal scale uses similar triangles. A small length, such as one tenth of a part, is divided into ten equal bits by drawing a sloping line across ten equal heights. Each step up the slope moves sideways by exactly one tenth of the small division.

Example: Construct a diagonal scale of R.F. = 1/4000 to read up to 500 m in metres. Show 438 m.

  1. Length of scale = 500 m/4000 = 50000 cm/4000 = 12.5 cm.
  2. Divide it into 5 equal parts: each is 100 m and 2.5 cm long.
  3. Divide the first part into 10: each is 10 m.
  4. Erect a perpendicular at the left end and mark 10 equal heights: each height stands for 1 m.
  5. Draw the diagonals across the first part.
  6. For 438 m, go up to height 8 (8 m), and measure from the 400 mark to the diagonal for 30 m.

Answer: A scale 12.5 cm long. On height line 8, 438 m runs from the 400 division to the third diagonal.

The vernier scale

A vernier reads a fine fraction of the main division with no diagonals. Usually, 10 vernier divisions cover the length of 9 main divisions. Each vernier division is therefore shorter by one tenth of a main division, which is the least count. To read one, note the main scale just before the vernier zero, then find which vernier line exactly matches a main line and add that number of least counts.

  • Least count = 1 MSD − 1 VSD = MSD/n, for a direct vernier.
  • The reading = main scale reading + vernier line × least count.
  • Vernier callipers commonly have a least count of 0.1 mm or 0.02 mm.

Example: In a vernier, 10 vernier divisions equal 9 main divisions, and 1 MSD = 1 mm. The main scale reads 24 mm, and the 7th vernier line coincides. Find the reading.

  1. 1 VSD = 9/10 = 0.9 mm.
  2. Least count = 1 − 0.9 = 0.1 mm.
  3. Reading = 24 + 7 × 0.1.

Answer: 24.7 mm

A scale shows an object at a larger or smaller size on paper. The representative fraction (R.F.) is the ratio of the length on the drawing to the actual length, with both in the same unit. A plain scale reads two units such as metres and decimetres, while a diagonal scale reads three such as metres, decimetres and centimetres.

  • Length of scale = R.F. × maximum length to be measured.
  • R.F. below 1 is a reducing scale; above 1 is enlarging.
  • A diagonal scale uses similar triangles.
  • Always mark the R.F. and units on the scale.

Key formulas

  • R.F. = drawing length/actual length
  • Length of scale = R.F. × max length

Practice questions

If 1 cm represents 1 m, the R.F. is

  1. 1/10
  2. 1/100
  3. 1/1000
  4. 100
Show the answer

Answer: B. 1/100 1 cm/100 cm.

A diagonal scale reads

  1. one unit
  2. two units
  3. three units
  4. no unit
Show the answer

Answer: C. three units For example, m, dm and cm.

An R.F. less than 1 is

  1. enlarging
  2. reducing
  3. full size
  4. invalid
Show the answer

Answer: B. reducing The drawing is smaller.

R.F. has

  1. no unit
  2. the unit cm
  3. the unit m
  4. the unit N
Show the answer

Answer: A. no unit A ratio.

Theory questions

Define R.F. A 5 cm line represents 25 m. Find R.F. (3 marks)

Show the model answer

R.F. = 5 cm/2500 cm = 1/500.

Construct a plain scale with R.F. = 1/50 to show metres and decimetres, long enough for 8 m. Give the steps. (8 marks)

Show the model answer

Length of scale = 800 cm/50 = 16 cm. Draw a 16 cm line and divide it into 8 equal parts for metres. Divide the first part into 10 for decimetres. Mark zero at the end of the first part, number them, and write R.F. = 1/50.

Unit II: Projections of points, lines, planes, solids

Topics: Quadrants and planes; points; lines parallel, perpendicular and inclined; simple planes; solids with the axis perpendicular or horizontal to a plane.

Projections of points

A point is fixed by its distance from each plane. The front view a′ is drawn at the point’s height above or below XY, and the top view a at its distance in front of or behind the VP. Both lie on one projector, perpendicular to XY. Height decides where a′ goes, and distance from the VP decides where a goes.

  • First quadrant: a′ above XY, a below XY.
  • Second quadrant: both above XY.
  • Third quadrant: a′ below XY, a above XY.
  • Fourth quadrant: both below XY.

Example: A point P is 20 mm below HP and 30 mm behind VP. State its quadrant and describe its views.

  1. Below HP and behind VP means the third quadrant.
  2. The front view shows the height: p′ is 20 mm below XY.
  3. The top view shows the distance from VP: behind VP places p 30 mm above XY.
  4. Both lie on one projector.

Answer: Third quadrant, with p′ 20 mm below XY and p 30 mm above XY.

Projections of lines

A line parallel to a plane shows its true length (TL) on that plane. A line perpendicular to a plane shows as a point on that plane. A line inclined to a plane is foreshortened on it, and a line inclined to both planes is foreshortened in both views, with apparent angles larger than the true ones.

To draw a line inclined to both planes, first draw it as if it were parallel to the VP, at its true angle θ: its base gives the plan length, and its top gives the height of b′. Then do the same with the other angle to get the elevation length and the distance of b from the VP. Finally, swing each length to meet its locus line.

Example: A line AB, 80 mm long, has A 15 mm above HP and 20 mm in front of VP. It is inclined at 30° to HP and 45° to VP. Find the lengths and the positions of b′ and b.

  1. Plan length = 80 cos 30° = 69.3 mm.
  2. Elevation length = 80 cos 45° = 56.6 mm.
  3. Height of b′ above HP = 15 + 80 sin 30° = 55 mm.
  4. Distance of b from VP = 20 + 80 sin 45° = 76.6 mm.
  5. Horizontal distance between the projectors = √(69.3² − 56.6²) = √(4802 − 3204) ≈ 40 mm.
  6. Mark b′ on the 55 mm line and b on the 76.6 mm line, 40 mm along from A.

Answer: Top view 69.3 mm, front view 56.6 mm, with end projectors 40 mm apart.

Projections of planes and solids

A plane parallel to the HP shows its true shape in the top view and appears as a line in the front view. A plane inclined to the HP shows as a line at its inclination in the front view, and is foreshortened in the top view.

Solids are drawn in stages. In stage 1, the solid rests in the simplest position, with its axis perpendicular to a plane, so that the view on that plane shows the true shape of the base. In stage 2, the front view from stage 1 is redrawn tilted. Every corner’s distance from XY in the top view stays unchanged, so each new top-view point is found by projecting down from the tilted view and across from the first top view.

  • Prism and cylinder: two equal bases joined by side faces.
  • Pyramid and cone: one base and an apex.
  • A hidden edge lies behind a visible surface: draw it dashed.

Projection represents a solid on two perpendicular reference planes, HP and VP, which divide space into four quadrants. A point is shown by its top view and front view, joined by a projector perpendicular to the reference line xy. A line parallel to a plane shows its true length on that plane. For a line inclined to both planes, the true length is found by rotating or using an auxiliary method.

  • First quadrant: above HP and in front of VP. Top view is below xy and front view is above.
  • Third quadrant: both views are reversed.
  • A line perpendicular to a plane projects as a point on that plane.
  • Plane figures are usually drawn in stages: parallel first and then tilted.

Practice questions

A point above HP and in front of VP lies in the

  1. first quadrant
  2. second quadrant
  3. third quadrant
  4. fourth quadrant
Show the answer

Answer: A. first quadrant Standard.

The line where HP and VP meet is

  1. xy
  2. the centre line
  3. the projector
  4. the normal
Show the answer

Answer: A. xy Reference line.

A line perpendicular to HP appears on HP as

  1. a point
  2. its true length
  3. a circle
  4. a dashed line
Show the answer

Answer: A. a point End view.

A line parallel to VP shows its true length in the

  1. front view
  2. top view
  3. side view only
  4. no view
Show the answer

Answer: A. front view It lies parallel to VP.

Theory questions

Draw the projections of a point 30 mm above HP and 20 mm in front of VP. State where each view lies. (3 marks)

Show the model answer

The front view is 30 mm above xy; the top view is 20 mm below xy, on the same vertical projector.

A line 60 mm long is parallel to VP and inclined at 30° to HP, with one end 15 mm above HP and 20 mm in front of VP. Give the steps to draw its views. (8 marks)

Show the model answer

Mark a′ 15 mm above xy and a 20 mm below on one projector. Draw a′b′ = 60 mm at 30° to xy: this is the true length in the front view. Project b′ down to a horizontal through a to obtain b. The top view ab is parallel to xy and has a length of 60 cos 30° ≈ 52 mm.

Unit III: Orthographic projection

Topics: Principle and method; first- and third-angle projection of simple objects.

The idea of first-angle projection

Imagine an object between you and a transparent plane. Parallel rays from its corners, perpendicular to the plane, mark its outline on the plane. A vertical plane (VP) gives the front view, and a horizontal plane (HP) gives the top view. The two planes meet along the reference line XY. To put both views on flat paper, the HP is swung down about XY.

In first-angle projection, which BIS recommends, the object is above the HP and in front of the VP. After the HP swings down, the top view lies below the front view. In third-angle projection, the planes lie between you and the object, so the top view lies above the front view.

Example: In first-angle projection, where is the view from the left placed on the sheet?

  1. In first angle, each view is drawn on the far side of the object from where you look.
  2. Looking from the left, the view appears on the right of the front view.

Answer: To the right of the front view

Example: A 30 mm cube rests on the HP with one face parallel to the VP and 10 mm in front of it. Describe its front and top views in first-angle projection.

  1. Front view: a 30 mm square standing on XY, since the cube rests on the HP.
  2. Top view: a 30 mm square below XY, its edge nearest XY drawn 10 mm below it, because that face is 10 mm in front of the VP.

Answer: A square on XY above, and a square starting 10 mm below XY

Orthographic projection shows an object through separate views, with parallel projectors perpendicular to the planes. In first-angle projection the object lies between the observer and the plane, so the top view goes below the front view. In third-angle projection the plane is between them, so the top view goes above. A sectional view cuts the object to reveal its interior, using hatching at 45°.

  • India’s BIS standard SP 46 favours first-angle projection.
  • A view shows one face: front, top or side.
  • Choose as the front view the one showing the most detail.
  • Solid projections usually start from the view that shows the true shape of the base.

Practice questions

In first-angle projection, the top view is placed

  1. below the front view
  2. above the front view
  3. left of the side view
  4. nowhere
Show the answer

Answer: A. below the front view Standard layout.

In third-angle projection, the top view is

  1. above the front view
  2. below the front view
  3. not used
  4. on the right
Show the answer

Answer: A. above the front view Standard layout.

Section lines are usually at

  1. 45°
  2. 90°
  3. 0°
  4. 10°
Show the answer

Answer: A. 45° Hatching.

Which is the front view chosen to show?

  1. most detail
  2. the least detail
  3. no edges
  4. only a corner
Show the answer

Answer: A. most detail Good practice.

Theory questions

Distinguish between first-angle and third-angle projection. (3 marks)

Show the model answer

First angle: object between observer and plane; the top view is below the front view. Third angle: plane between observer and object; the top view is above the front view.

Explain the purpose of a sectional view and give rules for hatching. (8 marks)

Show the model answer

A section reveals interior details by imagining the object cut by a plane. Hatching uses thin lines, usually at 45°, equally spaced. Adjacent parts are hatched in opposite directions. Hidden lines are normally omitted, and the cutting plane is shown by a chain line with letters.

Unit III: Isometric projection

Topics: Isometric scale, views and drawing of simple objects.

Isometric projection and the isometric scale

An isometric view shows three faces in one picture. Its three axes make 120° with one another. Vertical edges stay vertical, and the others are drawn at 30° to the horizontal. Since all three axes are equally inclined to the viewing plane, all edges shrink by the same factor, √(2/3) ≈ 0.816.

An isometric drawing ignores this shrinking and uses true lengths. The picture has the same shape but is about 22.5% larger, and it is much quicker to make. A true isometric projection uses the isometric scale, which you construct by comparing a 45° line carrying true lengths with a 30° line.

Example: A block measures 40 × 30 × 20 mm. Find the lengths used in an isometric projection, and in an isometric drawing.

  1. Isometric length = 0.816 × true length.
  2. 40 × 0.816 = 32.6 mm.
  3. 30 × 0.816 = 24.5 mm.
  4. 20 × 0.816 = 16.3 mm.
  5. An isometric drawing uses 40, 30 and 20 mm directly.

Answer: Projection: 32.6, 24.5 and 16.3 mm. Drawing: 40, 30 and 20 mm.

Circles: the four-centre method

A circle on an isometric face appears as an ellipse. To draw it, enclose it in an isometric square whose side equals the circle’s diameter. Join each obtuse corner to the midpoints of the two opposite sides. These lines cross at two points. The two obtuse corners and these two crossing points are the four centres: draw two large arcs and two small arcs, and they join smoothly.

  • Lines not parallel to the axes (non-isometric lines) do not keep the scale: locate their end points first.
  • To convert isometric to orthographic: choose the front direction, then read widths, heights and depths along the axes.
  • To convert orthographic to isometric: draw a box around the object, then cut away.

Example: A 40 mm circle lies on the top face of a block. What size of isometric square encloses it in an isometric drawing, and in an isometric projection?

  1. In an isometric drawing, true lengths are used: a 40 mm rhombus.
  2. In an isometric projection, lengths are scaled by 0.816: 40 × 0.816 = 32.6 mm.

Answer: 40 mm in the drawing, about 32.6 mm in the projection

An isometric view shows three faces in one picture. The three axes are 120° apart, with vertical edges drawn vertically and the others at 30° to the horizontal. In a true isometric projection lengths are reduced by the isometric scale, about 0.816. An isometric drawing uses true lengths for simplicity. Circles appear as ellipses.

  • Isometric length = true length × 0.816.
  • Lines parallel to the axes are measured; non-isometric lines are found by offsets.
  • Circles are drawn by the four-centre method.
  • Hidden lines are usually omitted.

Key formulas

  • Isometric length = 0.816 × true length

Practice questions

Isometric axes are

  1. 120° apart
  2. 90° apart
  3. 45° apart
  4. 30° apart
Show the answer

Answer: A. 120° apart Definition.

The isometric scale factor is about

  1. 0.816
  2. 0.5
  3. 1.414
  4. 0.707
Show the answer

Answer: A. 0.816 √(2/3).

A circle on an isometric face appears as

  1. an ellipse
  2. a square
  3. a triangle
  4. a line
Show the answer

Answer: A. an ellipse Foreshortened.

An isometric drawing uses

  1. true lengths
  2. half lengths
  3. no measurements
  4. double lengths
Show the answer

Answer: A. true lengths For simplicity.

Theory questions

Distinguish between isometric projection and isometric drawing. (3 marks)

Show the model answer

Isometric projection uses lengths reduced by the isometric scale. An isometric drawing uses true lengths, so it looks larger but is simpler to draw.

Describe how to construct an isometric scale and how to draw an isometric view of a rectangular block. (8 marks)

Show the model answer

Draw a horizontal line, and lines at 45° and 30° from one end. Mark true lengths on the 45° line and project them down to the 30° line, which gives isometric lengths. For a block, draw a vertical and two 30° edges from one corner, mark the lengths, complete parallels and darken the visible edges.

Unit IV: Free-hand sketches

Topics: V and square threads, hexagonal and square nuts and bolts, rivet heads and riveted joints.

Threads, bolts and nuts

A screw thread is a ridge wound in a helix round a cylinder (external thread, as on a bolt) or inside a hole (internal thread, as in a nut). Its terms: the major diameter is the largest, the minor (core) diameter the smallest; the crest is the top and the root the bottom of the thread; the pitch is the distance between neighbouring threads; the lead is how far the nut moves in one turn. For a single-start thread the lead equals the pitch; for a double-start thread it is twice the pitch.

Thread profiles suit different jobs. The V thread (the ISO metric thread has a 60° angle) grips well and is used for fastening. The square thread has low friction and transmits power, as in screw jacks and vices. The Acme thread (29°) is a stronger, easier-to-cut alternative for lead screws. The buttress thread takes heavy load in one direction, and the knuckle thread, with rounded tops, suits rough use such as rail couplings.

Hexagonal and square nuts and bolts are sketched with proportions based on the bolt’s nominal diameter D: nut thickness about D, width across flats about 1.5D + 3 mm, width across corners about 2D, and bolt head thickness about 0.8D. In drawings, threads are shown by convention rather than true helices: the root is a thin line, and in end view the root circle is drawn as a thin three-quarter circle.

  • Major and minor diameter; crest and root; pitch; lead
  • Lead = number of starts × pitch
  • V (60° metric): fastening. Square: power. Acme (29°): lead screws
  • Buttress: one-way load. Knuckle: rough use
  • Nut: thickness ≈ D; across flats ≈ 1.5D + 3; across corners ≈ 2D
  • Bolt head thickness ≈ 0.8D

Example: A double-start thread has a pitch of 2 mm. How far does the nut move in 3 turns?

  1. Lead = 2 × 2 = 4 mm per turn.
  2. 3 × 4.

Answer: 12 mm

Example: Find the sketching proportions of a hexagonal nut for an M20 bolt.

  1. Thickness ≈ D = 20 mm; across flats ≈ 1.5 × 20 + 3 = 33 mm.
  2. Across corners ≈ 2D = 40 mm.

Answer: About 20 mm thick, 33 mm across flats and 40 mm across corners

Example: Which thread would you choose for a screw jack, and why?

  1. A screw jack transmits power to lift a load.
  2. A square thread has low friction for power transmission.

Answer: A square thread

Rivets and riveted joints

A rivet is a permanent fastener: a round shank with a head on one end, put through holes in the plates and closed by forming a second head. Rivet heads include the snap (cup) head, the pan head, the countersunk head (flush with the surface) and the conical head. The snap head is sketched with a diameter of about 1.6d and a height of about 0.7d, where d is the shank diameter.

In a lap joint the plates overlap; in a butt joint they meet edge to edge and are joined by one or two cover (strap) plates. Joints may be single-riveted, with one row, or double-riveted, with two rows arranged in chain (opposite each other) or zig-zag (staggered).

The rivet diameter is often found from Unwin’s formula, d = 6√t, with t the plate thickness in mm. The pitch (distance between rivets in a row) is about 3d, and the margin (from the rivet centre to the plate edge) about 1.5d. Riveting has largely given way to welding, but it is still used in some structures and in aircraft.

  • Heads: snap, pan, countersunk, conical
  • Snap head: diameter ≈ 1.6d, height ≈ 0.7d
  • Lap joint; butt joint with one or two cover plates
  • Single or double riveted; chain or zig-zag
  • Unwin: d = 6√t; pitch ≈ 3d; margin ≈ 1.5d

Example: Two 16 mm plates are to be riveted. Find the rivet diameter, pitch and margin.

  1. d = 6√16 = 6 × 4 = 24 mm.
  2. Pitch ≈ 3 × 24 = 72 mm; margin ≈ 1.5 × 24 = 36 mm.

Answer: d = 24 mm, pitch about 72 mm, margin about 36 mm

Example: Which rivet head would you use where the surface must stay flat?

  1. A raised head would stand above the surface.
  2. A countersunk head sits flush.

Answer: A countersunk head

Threads convert rotation into linear motion. V-threads are used in fasteners since they give high friction, and square threads carry power as in screw jacks. Nuts and bolts are temporary fastenings. Rivets form permanent joints: in a lap joint the plates overlap, and in a butt joint they meet edge to edge with one or two cover plates.

  • Pitch: distance between adjacent threads.
  • Lead = pitch × number of starts.
  • Rivet head types: snap, pan, countersunk and conical.
  • Threads may be represented conventionally to save drawing time.

Key formulas

  • Lead = n × pitch

Practice questions

A screw jack usually uses a

  1. square thread
  2. V-thread
  3. no thread
  4. buttress only
Show the answer

Answer: A. square thread Low friction, power transmission.

A riveted joint is

  1. permanent
  2. temporary
  3. liquid
  4. sliding
Show the answer

Answer: A. permanent Removal destroys it.

Lead equals

  1. pitch × number of starts
  2. diameter
  3. pitch/2
  4. length
Show the answer

Answer: A. pitch × number of starts Definition.

In a butt joint, plates are

  1. edge to edge
  2. overlapped
  3. perpendicular
  4. not touching
Show the answer

Answer: A. edge to edge With cover plates.

Theory questions

Compare V-threads and square threads. (3 marks)

Show the model answer

V-threads have high friction and are used for fastening. Square threads have low friction and transmit power, as in a screw jack.

Sketch and describe the types of rivet heads and riveted joints. (8 marks)

Show the model answer

Heads: snap, pan, countersunk and conical. Joints: a lap joint, where plates overlap with one or more rows, and a butt joint, where plates meet edge to edge with a single or double cover plate. Rows may be chain or zig-zag riveted.

Unit V: Introduction to CAD

Topics: Tools, menus, toolbars; zoom, select, erase; annotations, dimensions, layers; basic shapes.

Telling the computer where points are

A CAD drawing is exact because points are given by numbers, not by eye. Absolute coordinates are measured from the origin. Relative coordinates start with @ and are measured from the last point. Polar coordinates give a distance and a direction from the last point. Most work uses relative and polar input, since you usually know the sizes rather than distances from the origin.

  • Absolute: 50,30
  • Relative: @20,10
  • Polar: @40<30
  • Angles are measured anticlockwise from the positive x-direction.

Example: A line starts at (10, 20). Its other end is entered as @60<30. Find the coordinates of its end.

  1. Δx = 60 cos 30° = 51.96.
  2. Δy = 60 sin 30° = 30.
  3. x = 10 + 51.96 = 61.96.
  4. y = 20 + 30 = 50.

Answer: (61.96, 50)

Example: Give the commands for a 100 × 60 rectangle starting at (20, 20).

  1. LINE, then 20,20.
  2. @100,0 for the bottom edge.
  3. @0,60 for the right edge.
  4. @-100,0 for the top edge.
  5. C to close back to the start.

Answer: A 100 × 60 rectangle drawn with one LINE command.

Drawing, editing and organising

Draw commands such as LINE, CIRCLE, ARC, POLYGON and ELLIPSE create entities. Modify commands such as TRIM, EXTEND, OFFSET, MIRROR, ARRAY, FILLET and CHAMFER edit them. Object snaps lock the cursor to exact positions, such as an endpoint, midpoint, centre or tangent point, which avoids tiny errors.

Layers work like transparent sheets. Outlines, centre lines, hidden lines and dimensions each go on their own layer, with a colour and line type, and a layer can be hidden, frozen or locked. Dimension styles control the text height, arrows and units.

  • ZOOM and PAN change only the view, never the object.
  • Wireframe: edges only.
  • Surface: skins without volume.
  • Solid: volume and mass properties, needed for analysis and manufacture.

Computer-aided drafting makes accurate, editable drawings. The screen has a menu, toolbars, a drawing area and a command line. Commands draw lines, circles and polygons; zoom and pan change the view; and erase and trim modify entities. Layers separate different kinds of line. Annotation and dimension commands finish the drawing.

  • Common commands: LINE, CIRCLE, POLYGON, TRIM, ZOOM, ERASE, DIM.
  • Layers control colour, line type and visibility.
  • Absolute, relative and polar coordinates can position points.
  • CAD files can be reused and edited quickly.

Key formulas

  • Relative: @dx,dy
  • Polar: @length<angle

Practice questions

Zoom changes

  1. the view only
  2. the object’s real size
  3. layers
  4. colours
Show the answer

Answer: A. the view only Display only.

Layers in CAD organise

  1. types of drawing content
  2. files
  3. printers
  4. keyboards
Show the answer

Answer: A. types of drawing content Such as centre lines and dimensions.

The command to remove entities is

  1. ERASE
  2. LINE
  3. ZOOM
  4. COPY
Show the answer

Answer: A. ERASE Definition.

Polar entry looks like

  1. @50<30
  2. 50,30,10
  3. x50
  4. #50
Show the answer

Answer: A. @50<30 Length and angle.

Theory questions

Give four advantages of CAD over manual drawing. (3 marks)

Show the model answer

Accuracy, easy editing, reuse of drawings and quicker copies and printing.

Explain coordinate input in CAD and the use of layers. (8 marks)

Show the model answer

Absolute coordinates are measured from the origin (x, y). Relative coordinates @dx,dy are measured from the last point. Polar coordinates @length<angle give a distance and direction. Layers group entities such as outlines, centre lines and dimensions, each with its own colour and line type, and can be turned off.

Chapters follow the SCTE Assam syllabus. The notes and questions were written for this studio and are not official.

Open this subject studio →