Urea (46 % N) is the most widely used nitrogen fertiliser in India. It is made from ammonia and the CO₂ by-product of the ammonia plant in two steps: a fast exothermic formation of ammonium carbamate and its slow endothermic dehydration to urea. Since the conversion in the reactor is only 60–65 %, unconverted carbamate must be decomposed and recycled. In the CO₂ stripping process, fresh CO₂ strips the reactor effluent at reactor pressure, so most of the recycle stays in the high-pressure loop and the plant is simpler and more energy-efficient.
Raw materials
- Liquid ammonia
- Carbon dioxide (from the ammonia plant, ≈ 0.75 t per t urea)
- Passivation air (O₂ protects stainless steel)
- Neem oil for coating (India)
Products
- Prilled or granulated urea (46 % N, biuret < 1 %)
- Technical urea, urea solutions (AdBlue/DEF)
- Neem-coated urea (mandatory in India since 2015)
Uses
- Fertiliser (≈ 90 %)
- Urea–formaldehyde and melamine resins
- Cattle feed supplement, diesel exhaust fluid
Reactions
- 2NH₃ + CO₂ ⇌ NH₂COONH₄ (ammonium carbamate) ΔH = −117 kJ/mol (fast)
- NH₂COONH₄ ⇌ NH₂CONH₂ + H₂O ΔH = +15.5 kJ/mol (slow, equilibrium-limited)
- Side reaction: 2NH₂CONH₂ → NH₂CONHCONH₂ (biuret) + NH₃ (high T, long residence, low NH₃)
- Hydrolysis (reverse) in dilute solutions at high temperature
Operating conditions
| Reactor | 180–185 °C, 140–145 bar, NH₃/CO₂ molar ratio ≈ 3, H₂O/CO₂ ≈ 0.4–0.5 |
|---|---|
| Conversion | ≈ 60 % of CO₂ per pass (total recycle ⇒ ≈ 99 % overall) |
| HP stripper | Falling-film, steam heated (≈ 20 bar steam), CO₂ as stripping gas |
| LP recirculation | 3–4 bar decomposer and condenser |
| Evaporation | Two-stage vacuum, 130–140 °C, to 99.7 % melt |
| Prilling | Tower 60–100 m high, counter-current air |
Process, step by step
- Feed compression. CO₂ from the ammonia plant (with a little passivation air) is compressed to about 145 bar in a multistage centrifugal compressor. Liquid ammonia is pumped to the same pressure by high-pressure pumps.
- High-pressure carbamate condensation. Ammonia and the gases leaving the top of the stripper (NH₃ + CO₂) condense to carbamate in the HP carbamate condenser (a pool condenser in newer designs). The large heat of carbamate formation generates low-pressure steam on the shell side.
- Urea reactor. Carbamate solution and remaining gases enter the bottom of the tall reactor fitted with sieve trays to reduce back-mixing. At 180–185 °C and 140 bar carbamate dehydrates to urea and water; about 60 % of the CO₂ is converted. Residence time is about 30–60 minutes.
- CO₂ stripping. Reactor effluent flows down the steam-heated tubes of the falling-film stripper while fresh CO₂ rises inside them. Lowering the NH₃ partial pressure and heating decomposes most of the unconverted carbamate into NH₃ and CO₂, which go back to the HP condenser — all at reactor pressure.
- HP scrubbing. Inerts leaving the reactor top carry NH₃ and CO₂; they are washed with carbamate solution from the LP section in the HP scrubber, and the inerts are vented safely.
- Low-pressure recirculation. The stripped urea solution is let down to about 3–4 bar; residual carbamate is decomposed in the LP rectifying column and condensed to carbamate solution that is pumped back to the HP loop via the scrubber.
- Evaporation. The urea solution (≈ 75 %) is concentrated to a 99.7 % melt in two-stage vacuum evaporators. Short residence time and low pressure keep biuret formation low. The evaporator condensates are treated (desorption and hydrolysis) to recover NH₃ and urea.
- Prilling or granulation. Molten urea is sprayed from a rotating prilling bucket at the top of a prilling tower; droplets solidify into prills while falling against cooling air. Modern plants use fluid-bed granulators for larger, stronger granules. Product is cooled, coated with neem oil and bagged.
Major engineering problems
Severe corrosion by carbamate
Urea-grade 316L, duplex (Safurex) or zirconium in HP equipment; passivation air (oxygen) in the CO₂ feed; titanium-lined strippers in some designs.
Biuret formation
Short residence at high temperature, vacuum evaporation, excess ammonia; biuret < 1 % (harms seedlings).
Equilibrium-limited conversion
Excess NH₃, optimal temperature, low water; total recycle of unconverted material by stripping.
Prill tower dust and ammonia emissions
Wet scrubbers, granulation instead of prilling, acid scrubbing for NH₃.
Caking of product
Formaldehyde/urea-formaldehyde additive, cooling before storage, coating.
Waste water with urea and NH₃
Hydrolyser–desorber treatment and reuse as boiler feed.
Notes
- Urea contains 46.6 % N (28/60); 1 t urea needs 0.567 t NH₃ and 0.733 t CO₂ stoichiometrically.
- Other processes: Snamprogetti ammonia stripping, Toyo ACES; older once-through and partial-recycle processes.
- Neem coating slows nitrification and stops diversion of subsidised urea to industry.
- Urea plants are always integrated with ammonia plants because of the CO₂ supply.
Practice questions
The intermediate compound in urea manufacture is
- ammonium carbonate
- ammonium carbamate
- biuret
- cyanamide
Show the answer
Answer: B. ammonium carbamate NH₂COONH₄.
Dehydration of carbamate to urea is
- fast and exothermic
- slow and endothermic
- catalysed by iron
- irreversible
Show the answer
Answer: B. slow and endothermic ΔH ≈ +15.5 kJ/mol, equilibrium-limited.
In the Stamicarbon process the stripping agent is
- ammonia
- CO₂
- steam only
- nitrogen
Show the answer
Answer: B. CO₂ Fresh CO₂ feed strips the reactor effluent.
The undesirable by-product in urea is
- carbamate
- biuret
- melamine
- cyanuric acid
Show the answer
Answer: B. biuret Formed at high temperature; harmful to plants.
Nitrogen content of urea is about
- 21 %
- 35 %
- 46 %
- 82 %
Show the answer
Answer: C. 46 % 28/60.
Corrosion in urea plants is controlled by adding
- nitrogen
- oxygen (passivation air) to CO₂
- chlorine
- hydrogen
Show the answer
Answer: B. oxygen (passivation air) to CO₂ Keeps the stainless steel passive.
Theory questions
Write the reactions involved in urea synthesis and explain why recycling is necessary. (4 marks)
Show the model answer
2NH₃ + CO₂ → NH₂COONH₄ (fast, exothermic); NH₂COONH₄ ⇌ NH₂CONH₂ + H₂O (slow, endothermic, equilibrium ≈ 60–65 % at 185 °C, 140 bar). Unconverted carbamate and excess NH₃ must be decomposed and recycled to obtain high overall yield.
Explain the CO₂ stripping process for urea with a flow sheet. (10 marks)
Show the model answer
CO₂ compressed to 145 bar with passivation air enters the falling-film HP stripper; NH₃ pumped to the HP carbamate condenser together with stripper off-gas; carbamate to the reactor (185 °C, 140 bar, NH₃/CO₂ ≈ 3); reactor effluent stripped by CO₂; inerts scrubbed; stripped solution to LP recirculation, then vacuum evaporation to 99.7 % melt; prilling or granulation; neem coating.
What is biuret? How is its formation minimised? (3 marks)
Show the model answer
Biuret NH₂CONHCONH₂ forms from two urea molecules with loss of NH₃ at high temperature and long residence; it is toxic to seedlings. Minimised by short residence time, vacuum evaporation at lower temperature and excess ammonia; limit < 1 %.
Frequently asked questions
How is urea manufactured?
Total-recycle CO₂ stripping process (Stamicarbon type). Urea (46 % N) is the most widely used nitrogen fertiliser in India. It is made from ammonia and the CO₂ by-product of the ammonia plant in two steps: a fast exothermic formation of ammonium carbamate and its slow endothermic dehydration to urea. Since the conversion in the reactor is only 60–65 %, unconverted carbamate must be decomposed and recycled. In the CO₂ stripping process, fresh CO₂ strips the reactor effluent at reactor pressure, so most of the recycle stays in the high-pressure loop and the plant is simpler and more energy-efficient.
What raw materials are used to make urea?
Liquid ammonia; Carbon dioxide (from the ammonia plant, ≈ 0.75 t per t urea); Passivation air (O₂ protects stainless steel); Neem oil for coating (India)
What catalyst is used in urea production?
no catalyst (thermal dehydration of carbamate)
What is urea used for?
Fertiliser (≈ 90 %); Urea–formaldehyde and melamine resins; Cattle feed supplement, diesel exhaust fluid