IITIAN1997 STUDIO

Phenol

Cumene (Hock) process — phenol and acetone

Watch the animated P&ID →

More than 90 % of phenol is made by the cumene process. Benzene is alkylated with propylene to cumene (isopropylbenzene), cumene is oxidised with air to cumene hydroperoxide (CHP), and CHP is split by acid into phenol and acetone (Hock rearrangement). The process produces about 0.62 t of acetone per tonne of phenol, so its economics depend on both products. Phenol is the raw material for bisphenol-A (polycarbonate, epoxy), phenolic resins and caprolactam (nylon-6).

Raw materials

  • Benzene and propylene
  • Air (oxidation)
  • Catalysts: zeolite (beta/MCM-22) or solid phosphoric acid (alkylation); H₂SO₄ (cleavage)
  • NaOH/Na₂CO₃ (oxidation pH control)

Products

  • Phenol (≈ 1 t)
  • Acetone (≈ 0.62 t per t phenol)
  • By-products: α-methylstyrene (hydrogenated back to cumene), acetophenone, heavy ends

Uses

  • Bisphenol-A → polycarbonate and epoxy resins
  • Phenol–formaldehyde resins (Bakelite, plywood adhesives)
  • Caprolactam (nylon-6), alkylphenols, salicylic acid (aspirin), disinfectants

Reactions

  • Alkylation: C₆H₆ + CH₂=CHCH₃ → C₆H₅CH(CH₃)₂ (cumene) zeolite, 150–250 °C
  • Oxidation: C₆H₅CH(CH₃)₂ + O₂ → C₆H₅C(CH₃)₂OOH (CHP) 90–120 °C, 5–7 bar
  • Cleavage: C₆H₅C(CH₃)₂OOH → C₆H₅OH + CH₃COCH₃ H₂SO₄, 50–80 °C (highly exothermic)
  • Side: CHP → dimethylbenzyl alcohol → α-methylstyrene

Operating conditions

AlkylationLiquid-phase zeolite, excess benzene (B/P 2–4), 150–250 °C, 20–40 bar
OxidationAir, 90–120 °C, slightly alkaline, CHP 20–30 % in reactor (safety)
ConcentrationVacuum evaporation of CHP to 65–85 %
CleavageDilute H₂SO₄, 50–80 °C, careful temperature control
PurificationNeutralisation and distillation train; phenol 99.9 %

Process, step by step

  1. Alkylation of benzene. Benzene and propylene react in fixed beds of zeolite catalyst with a large benzene excess to suppress polyalkylation. Di- and tri-isopropylbenzenes are transalkylated with benzene back to cumene, and the cumene is purified by distillation.
  2. Oxidation. Cumene is oxidised by air bubbled through a series of bubble-column oxidisers at 90–120 °C under slight alkaline conditions. Conversion is limited to 20–30 % CHP for safety and selectivity; off-gas is chilled and passed through carbon beds to recover cumene.
  3. CHP concentration. Unreacted cumene is evaporated under vacuum, raising CHP to 65–85 %; the cumene is recycled to the oxidisers.
  4. Acid cleavage. Concentrated CHP is fed to a cleavage reactor with circulating product and a small amount of sulphuric acid. The Hock rearrangement is very fast and exothermic; product recirculation and coolers keep the temperature at 50–80 °C, avoiding runaway decomposition.
  5. Neutralisation and distillation. The cleavage mixture is neutralised and distilled in a train of columns: crude acetone column, acetone finishing, cumene/α-methylstyrene column (AMS hydrogenated back to cumene), and phenol finishing; heavy residues (tar) are burnt.

Major engineering problems

Explosive decomposition of CHP

Limit concentration and temperature, emergency quench and dump systems, careful acid dosing.

Polyalkylation and selectivity

Excess benzene, zeolite catalysts, transalkylation.

Coupled phenol/acetone markets

Acetone to MIBK/MMA/bisphenol-A; alternative processes (direct benzene oxidation) under study.

Phenol toxicity and effluent

Phenol recovery from waste water by extraction, biological treatment.

Corrosion in cleavage

Stainless steel/alloys, controlled acid concentration.

Notes

  • Mass ratio acetone : phenol = 58/94 = 0.62.
  • Older routes: benzene sulphonation–alkali fusion, chlorobenzene (Dow), toluene oxidation (benzoic acid).
  • Bisphenol-A: 2 phenol + acetone → BPA + H₂O (acid ion-exchange resin).

Practice questions

In the cumene process the co-product of phenol is

  1. acetic acid
  2. acetone
  3. methanol
  4. benzene
Show the answer

Answer: B. acetone 0.62 t per t phenol.

Cumene is made by alkylating benzene with

  1. ethylene
  2. propylene
  3. methanol
  4. chlorine
Show the answer

Answer: B. propylene Isopropylbenzene.

Cumene hydroperoxide is cleaved using

  1. NaOH
  2. dilute H₂SO₄
  3. Pt
  4. heat only
Show the answer

Answer: B. dilute H₂SO₄ Hock rearrangement.

CHP concentration in the oxidiser is limited to 20–30 % mainly for

  1. colour
  2. safety and selectivity
  3. cost of air
  4. viscosity
Show the answer

Answer: B. safety and selectivity Peroxide hazard.

Phenol is the raw material for

  1. PVC
  2. bisphenol-A and phenolic resins
  3. polyethylene
  4. SBR
Show the answer

Answer: B. bisphenol-A and phenolic resins Also caprolactam.

Theory questions

Describe the manufacture of phenol by the cumene process. (8 marks)

Show the model answer

Benzene + propylene alkylated on zeolite (excess benzene, transalkylation) → cumene; air oxidation at 90–120 °C to 20–30 % CHP; vacuum concentration to 80 %; acid cleavage with H₂SO₄ at 50–80 °C → phenol + acetone; neutralisation; distillation (acetone, cumene/AMS recycle, phenol, tar).

Frequently asked questions

How is phenol manufactured?

Cumene (Hock) process — phenol and acetone. More than 90 % of phenol is made by the cumene process. Benzene is alkylated with propylene to cumene (isopropylbenzene), cumene is oxidised with air to cumene hydroperoxide (CHP), and CHP is split by acid into phenol and acetone (Hock rearrangement). The process produces about 0.62 t of acetone per tonne of phenol, so its economics depend on both products. Phenol is the raw material for bisphenol-A (polycarbonate, epoxy), phenolic resins and caprolactam (nylon-6).

What raw materials are used to make phenol?

Benzene and propylene; Air (oxidation); Catalysts: zeolite (beta/MCM-22) or solid phosphoric acid (alkylation); H₂SO₄ (cleavage); NaOH/Na₂CO₃ (oxidation pH control)

What catalyst is used in phenol production?

zeolite (alkylation) and sulphuric acid (cleavage)

What is phenol used for?

Bisphenol-A → polycarbonate and epoxy resins; Phenol–formaldehyde resins (Bakelite, plywood adhesives); Caprolactam (nylon-6), alkylphenols, salicylic acid (aspirin), disinfectants

Watch the animated P&ID →