IITIAN1997 STUDIO

Hydrogenation of Oils

Vanaspati (hydrogenated vegetable fat) with nickel catalyst

Watch the animated P&ID →

Hydrogenation adds hydrogen to the carbon–carbon double bonds of unsaturated fatty acids in an oil, raising its melting point and oxidative stability and turning liquid oils into semi-solid fats — vanaspati ghee, margarine and shortenings. Refined oil is reacted with pure hydrogen in an agitated, dead-end batch reactor over a finely divided supported nickel catalyst at 150–200 °C and 2–5 bar. The reaction is stopped at the target iodine value/melting point; the catalyst is filtered off and the product is post-refined.

Raw materials

  • Refined, dried oil (low in soap, sulphur, phosphatides, FFA)
  • Hydrogen (electrolytic or reformer H₂, > 99.9 %)
  • Nickel catalyst (Ni on kieselguhr/silica, 20–25 % Ni)

Products

  • Vanaspati (hydrogenated fat, MP 31–41 °C), shortening, margarine base
  • Hardened oils for soaps and industrial uses

Uses

  • Cooking fat, bakery and confectionery
  • Hardened fat for soap and fatty acid production

Reactions

  • –CH=CH– + H₂ → –CH₂–CH₂– (Ni catalyst, exothermic ≈ −120 kJ/mol per double bond)
  • Linolenic → linoleic → oleic → stearic (selective sequence)
  • Triolein + 3H₂ → tristearin
  • Isomerisation side reaction: cis → trans (elaidic acid), positional isomers

Operating conditions

Temperature150–200 °C (higher → more selective but more trans)
Hydrogen pressure2–5 bar (low pressure → selective)
Catalyst0.05–0.2 % Ni on oil, supported on kieselguhr
AgitationHigh — gas–liquid mass transfer controls the rate
End pointIodine value / refractive index / melting point (IV drops by ≈ 1 per 0.0035 % H₂ absorbed)

Process, step by step

  1. Oil pre-treatment. Oil must be fully refined and bleached, dry and free of soap, sulphur and phosphorus compounds, all of which poison the nickel catalyst. It is deaerated and heated in a feed tank under vacuum.
  2. Hydrogen supply. Hydrogen produced by water electrolysis (or reforming) is purified, dried and compressed into a gas holder, then fed to the reactor at 2–5 bar.
  3. Hydrogenation reaction. Oil and slurried catalyst are charged to the converter (autoclave) fitted with a gas-dispersing agitator and heating/cooling coils. Hydrogen is admitted; the exothermic reaction is controlled by cooling water. Samples are checked for refractive index/iodine value until the required hardness is reached (typically 1–3 h). Unreacted gas is recirculated (dead-end operation).
  4. Catalyst removal. The hardened oil is cooled to about 90 °C and filtered through plate-and-frame or leaf filters to remove nickel catalyst, which can be reused for a few batches; dissolved nickel traces are removed by post-bleaching with earth and citric acid.
  5. Post-refining, deodorising and packing. The fat is post-bleached, deodorised, blended, fortified with vitamins A and D (mandatory in vanaspati) and chilled in scraped-surface heat exchangers (votator) to give a fine, smooth crystal texture before packing in tins.

Major engineering problems

Catalyst poisoning

Thorough refining of feed oil; low sulphur and phosphorus; catalyst dosing control.

Trans fatty acids (health)

Lower temperature/higher pressure, selective catalysts, interesterification and fractionation alternatives; India limits trans fat to 2 %.

Hydrogen safety

Flameproof electricals, leak detection, nitrogen purging, relief valves.

Heat removal and mass transfer

Efficient agitators and gas dispersion, cooling coils.

Nickel in product

Filtration and post-bleaching with chelating agents.

Notes

  • Selectivity: hydrogenating linolenic before linoleic before oleic preserves oil quality and avoids excessive saturation.
  • Vanaspati in India must contain 5 % sesame oil (identification) under earlier rules and added vitamins.
  • Alternatives to partial hydrogenation: interesterification (enzymatic/chemical) and fractionation of palm oil.

Practice questions

The catalyst for hydrogenation of oils is

  1. platinum
  2. nickel
  3. iron
  4. vanadium
Show the answer

Answer: B. nickel Ni on kieselguhr.

Hydrogenation lowers the oil’s

  1. melting point
  2. iodine value
  3. saponification value
  4. density only
Show the answer

Answer: B. iodine value Fewer double bonds.

An undesirable by-product of partial hydrogenation is

  1. glycerol
  2. trans fatty acids
  3. soap
  4. hexane
Show the answer

Answer: B. trans fatty acids Elaidic acid etc.

Typical hydrogenation temperature is

  1. 30–50 °C
  2. 150–200 °C
  3. 400 °C
  4. 700 °C
Show the answer

Answer: B. 150–200 °C With 2–5 bar H₂.

Catalyst poisons in hydrogenation include

  1. nitrogen
  2. sulphur and soap
  3. water vapour only
  4. carbon dioxide
Show the answer

Answer: B. sulphur and soap Hence the oil must be refined.

Theory questions

Explain the hydrogenation of vegetable oils with a flow diagram. (8 marks)

Show the model answer

Refined dry oil + Ni catalyst in agitated autoclave at 150–200 °C, 2–5 bar H₂ (dead-end with recirculation), cooling coils; end point by IV/RI; filter catalyst; post-bleach (citric acid) and deodorise; add vitamins; chill in votator; pack. Selectivity and trans fat control by T, P, agitation.

What is meant by selective hydrogenation? (3 marks)

Show the model answer

Preferential hydrogenation of the more unsaturated acids (linolenic → linoleic → oleic) before saturation of oleic to stearic; favoured by high temperature, low pressure, low agitation and selective catalysts; gives stable fats without excessive hardness.

Frequently asked questions

How is hydrogenation of oils manufactured?

Vanaspati (hydrogenated vegetable fat) with nickel catalyst. Hydrogenation adds hydrogen to the carbon–carbon double bonds of unsaturated fatty acids in an oil, raising its melting point and oxidative stability and turning liquid oils into semi-solid fats — vanaspati ghee, margarine and shortenings. Refined oil is reacted with pure hydrogen in an agitated, dead-end batch reactor over a finely divided supported nickel catalyst at 150–200 °C and 2–5 bar. The reaction is stopped at the target iodine value/melting point; the catalyst is filtered off and the product is post-refined.

What raw materials are used to make hydrogenation of oils?

Refined, dried oil (low in soap, sulphur, phosphatides, FFA); Hydrogen (electrolytic or reformer H₂, > 99.9 %); Nickel catalyst (Ni on kieselguhr/silica, 20–25 % Ni)

What catalyst is used in hydrogenation of oils production?

finely divided nickel on kieselguhr

What is hydrogenation of oils used for?

Cooking fat, bakery and confectionery; Hardened fat for soap and fatty acid production

Watch the animated P&ID →