IITIAN1997 STUDIO

Phosphoric Acid

Wet process (dihydrate) from rock phosphate

Watch the animated P&ID →

Wet-process phosphoric acid is the intermediate for TSP, DAP, MAP and NPK fertilisers. Finely ground rock phosphate (fluorapatite) is digested with sulphuric acid; phosphoric acid goes into solution while calcium precipitates as gypsum. In the common dihydrate process the slurry is held at 70–80 °C so that well-filterable CaSO₄·2H₂O crystals form; the gypsum is filtered and washed, and the 26–32 % P₂O₅ filter acid is concentrated by vacuum evaporation to 52–54 % P₂O₅ (merchant-grade acid).

Raw materials

  • Rock phosphate (fluorapatite Ca₁₀F₂(PO₄)₆, 30–38 % P₂O₅) — mostly imported (Morocco, Jordan) besides Rajasthan
  • Sulphuric acid 98 % (≈ 2.6–2.8 t per t P₂O₅)
  • Water

Products

  • Phosphoric acid 26–32 % P₂O₅ (filter grade) and 52–54 % P₂O₅ (merchant grade)
  • By-products: phosphogypsum (≈ 4.5–5 t per t P₂O₅), fluosilicic acid H₂SiF₆

Uses

  • DAP, MAP, TSP and NPK fertilisers
  • Purified acid for detergents (STPP), food (soft drinks), animal feed phosphates
  • Metal treatment

Reactions

  • Ca₁₀F₂(PO₄)₆ + 10H₂SO₄ + 20H₂O → 6H₃PO₄ + 10CaSO₄·2H₂O + 2HF
  • 6HF + SiO₂ → H₂SiF₆ + 2H₂O ; SiF₄ evolved, scrubbed to fluosilicic acid
  • Thermal route (pure acid): 2Ca₃(PO₄)₂ + 6SiO₂ + 10C → P₄ + 6CaSiO₃ + 10CO; P₄ + 5O₂ → P₄O₁₀ → H₃PO₄

Operating conditions

DigestionDihydrate: 70–80 °C, 26–32 % P₂O₅, 2–3 % free H₂SO₄, 4–8 h residence
Hemihydrate process90–110 °C, 40–50 % P₂O₅ directly
FiltrationTilting-pan (Prayon) or belt vacuum filter, counter-current washing
ConcentrationForced-circulation vacuum evaporators, graphite heaters, to 52–54 % P₂O₅
P₂O₅ recovery94–96 %

Process, step by step

  1. Rock grinding. Rock phosphate is ground in ball or roller mills to about 60–70 % below 75 µm (or fed as wet slurry), so that it is attacked rapidly and completely.
  2. Digestion (attack). Ground rock, sulphuric acid and return (recycled weak) acid are fed to a series of agitated reactors (or a single large compartmented reactor). Sulphate concentration and temperature are held so that gypsum dihydrate crystallises as large, easily filterable crystals and does not coat unreacted rock particles.
  3. Cooling. The reaction is exothermic; slurry is circulated through a vacuum flash cooler (or air-cooled) to hold 70–80 °C. Fluorine compounds (HF, SiF₄) liberated in the reactors and cooler go to the scrubber.
  4. Gypsum filtration. The slurry is filtered on a tilting-pan or horizontal belt vacuum filter. The cake is washed counter-currently with water; the first filtrate is the product acid (26–32 % P₂O₅), while weaker wash filtrates are returned to the reactor as return acid. Washed phosphogypsum is pumped to a stack or used for cement/plasterboard.
  5. Concentration. Filter acid is clarified and concentrated in forced-circulation vacuum evaporators heated by LP steam in graphite or alloy exchangers to 52–54 % P₂O₅. Sludge is removed by clarification.
  6. Fluorine recovery. Fluorine-containing vapours from the reactors and evaporators are scrubbed with water, giving fluosilicic acid (H₂SiF₆, ≈ 18–25 %) used for AlF₃ or sodium fluosilicate — preventing fluoride pollution.

Major engineering problems

Phosphogypsum disposal (≈ 5 t per t P₂O₅)

Lined gypsum stacks; use in cement, gypsum boards, soil amendment; radioactivity and fluoride monitoring.

Fluoride emissions

Scrubbers producing H₂SiF₆; closed systems.

Corrosion and scaling

Rubber-lined/316L/alloy 20 agitators and pumps; graphite heat exchangers; periodic descaling of fluosilicates and gypsum.

Filtration and P₂O₅ losses

Control of sulphate level and temperature for good crystals; counter-current washing; hemihydrate–dihydrate processes for higher recovery.

Impurities (Fe, Al, Mg)

Rock selection, sludge removal; affect product viscosity and fertiliser quality.

Notes

  • P₂O₅ ↔ H₃PO₄: % H₃PO₄ = % P₂O₅ × 1.38.
  • Superphosphoric acid (68–72 % P₂O₅) contains polyphosphates and is used for liquid fertilisers.
  • Thermal (furnace) acid is purer but far costlier; used for food and technical grades.

Practice questions

In the dihydrate process calcium leaves as

  1. CaSO₄·½H₂O
  2. CaSO₄·2H₂O
  3. CaF₂
  4. CaHPO₄
Show the answer

Answer: B. CaSO₄·2H₂O Gypsum.

Typical dihydrate digestion temperature is

  1. 30 °C
  2. 70–80 °C
  3. 150 °C
  4. 500 °C
Show the answer

Answer: B. 70–80 °C Higher temperatures form hemihydrate.

The main solid waste of a phosphoric acid plant is

  1. slag
  2. phosphogypsum
  3. lime mud
  4. red mud
Show the answer

Answer: B. phosphogypsum ≈ 5 t per t P₂O₅.

Fluorine is recovered as

  1. HF gas
  2. fluosilicic acid
  3. CaF₂ from the filter
  4. NaF
Show the answer

Answer: B. fluosilicic acid Scrubbing SiF₄/HF with water.

Merchant-grade phosphoric acid contains about

  1. 10 % P₂O₅
  2. 28 % P₂O₅
  3. 54 % P₂O₅
  4. 72 % P₂O₅
Show the answer

Answer: C. 54 % P₂O₅ After vacuum evaporation.

Theory questions

Describe the wet process for phosphoric acid with a flow sheet. (8 marks)

Show the model answer

Rock grinding; digestion with H₂SO₄ and return acid at 70–80 °C (dihydrate); flash cooling; vacuum filtration and counter-current washing of gypsum; filter acid 26–32 % P₂O₅; vacuum evaporation to 52–54 %; fluorine scrubbing to H₂SiF₆; phosphogypsum stacking.

What are the problems associated with phosphogypsum? (3 marks)

Show the model answer

Huge volume (≈ 5 t/t P₂O₅), residual acidity, fluoride and radioactivity (radium), stack stability and groundwater pollution; utilisation in cement retarder, plaster boards and soil conditioner.

Frequently asked questions

How is phosphoric acid manufactured?

Wet process (dihydrate) from rock phosphate. Wet-process phosphoric acid is the intermediate for TSP, DAP, MAP and NPK fertilisers. Finely ground rock phosphate (fluorapatite) is digested with sulphuric acid; phosphoric acid goes into solution while calcium precipitates as gypsum. In the common dihydrate process the slurry is held at 70–80 °C so that well-filterable CaSO₄·2H₂O crystals form; the gypsum is filtered and washed, and the 26–32 % P₂O₅ filter acid is concentrated by vacuum evaporation to 52–54 % P₂O₅ (merchant-grade acid).

What raw materials are used to make phosphoric acid?

Rock phosphate (fluorapatite Ca₁₀F₂(PO₄)₆, 30–38 % P₂O₅) — mostly imported (Morocco, Jordan) besides Rajasthan; Sulphuric acid 98 % (≈ 2.6–2.8 t per t P₂O₅); Water

What catalyst is used in phosphoric acid production?

no catalyst (sulphuric acid digestion)

What is phosphoric acid used for?

DAP, MAP, TSP and NPK fertilisers; Purified acid for detergents (STPP), food (soft drinks), animal feed phosphates; Metal treatment

Watch the animated P&ID →