IITIAN1997 STUDIO

Sulphuric Acid

Double contact – double absorption (DCDA) process

Watch the animated P&ID →

Sulphuric acid is the most produced chemical in the world and its consumption is an index of a country’s industrial activity. Modern plants burn molten sulphur in dry air to SO₂, oxidise it over vanadium pentoxide catalyst in a multi-bed converter, and absorb the SO₃ in 98–98.5 % acid. In the double contact – double absorption (DCDA) scheme, SO₃ is removed after the third bed so that the equilibrium in the fourth bed is pushed further, giving 99.7–99.9 % overall conversion and very low SO₂ emission. The strongly exothermic reactions make the plant a net exporter of high-pressure steam.

Raw materials

  • Elemental sulphur (from Claus units of refineries and gas plants, or Frasch mining)
  • Alternative SO₂ sources: iron pyrites (FeS₂) roasting, smelter off-gases (Cu, Zn), spent acid regeneration
  • Air (dried) and process water

Products

  • 98–99 % H₂SO₄
  • Oleum (fuming sulphuric acid, 20–65 % free SO₃)
  • By-product: high-pressure steam (≈ 1.2–1.4 t per t acid)

Uses

  • Phosphatic fertilisers (phosphoric acid, SSP) and ammonium sulphate — about 60 % of demand
  • Petroleum refining (alkylation), steel pickling
  • Detergents (sulphonation), titanium dioxide pigments, rayon, lead-acid batteries, explosives (nitration mixtures)

Reactions

  • S (l) + O₂ → SO₂ ΔH = −297 kJ/mol
  • SO₂ + ½ O₂ ⇌ SO₃ ΔH = −99 kJ/mol (V₂O₅ catalyst, reversible, exothermic)
  • SO₃ + H₂O (in 98 % acid) → H₂SO₄ ΔH = −130 kJ/mol
  • SO₃ + H₂SO₄ → H₂S₂O₇ (oleum)

Operating conditions

Sulphur burner1000–1150 °C; gas 10–11.5 % SO₂
Converter inlet410–440 °C (catalyst ignition ≈ 380–400 °C)
CatalystV₂O₅ (6–9 %) promoted with K₂SO₄/Cs₂SO₄ on silica (kieselguhr)
Pressure1.2–1.5 atm (slightly above atmospheric)
Absorbing acid98–98.5 % H₂SO₄ at 70–80 °C
Overall conversion99.7–99.9 % (DCDA); ≈ 98 % single contact

Process, step by step

  1. Air drying. Atmospheric air is drawn through a packed drying tower irrigated with 93–98 % sulphuric acid, which removes moisture. Dry air is essential: water vapour would form sulphuric acid mist with SO₃ that passes through the absorbers and corrodes downstream equipment. The main air blower then supplies the dried air to the burner.
  2. Sulphur melting and burning. Solid sulphur is melted with steam coils at 135–145 °C (viscosity is lowest there), filtered and pumped through atomising guns into a horizontal brick-lined burner. It burns in excess dry air to SO₂; the gas leaves at about 1000–1150 °C containing 10–11.5 % SO₂ and 9–10 % O₂.
  3. Heat recovery. The hot gas passes through a waste-heat boiler that raises high-pressure steam and cools the gas to the converter inlet temperature of about 420 °C. Further economisers and superheaters between the converter beds recover the heat of oxidation.
  4. Catalytic conversion (beds 1–3). In the converter the gas passes down through three beds of vanadium catalyst. Each bed operates adiabatically, so the temperature rises as SO₂ is oxidised (about 2.6–2.8 °C per 1 % conversion for 10 % SO₂ gas). Because the reaction is reversible and exothermic, high temperature limits equilibrium conversion: the gas is cooled between beds to bring it back to ≈ 420–440 °C before the next bed. After three beds about 93–95 % of the SO₂ is converted.
  5. Intermediate absorption. Gas from the third bed is cooled and sent to the intermediate absorption tower where SO₃ is absorbed in circulating 98.5 % acid. Removing SO₃ shifts the equilibrium SO₂ + ½O₂ ⇌ SO₃ to the right, so the remaining SO₂ can be converted almost completely. The gas is reheated (by cross-exchange) and returned to the fourth bed.
  6. Final conversion and absorption. The fourth bed converts the remaining SO₂ (> 99.7 % overall). The gas is cooled and enters the final absorption tower, again irrigated with 98.5 % acid. Candle-type fibre mist eliminators at the tower outlets remove acid mist.
  7. Acid circulation and product. Acid from the towers collects in a pump tank. Water (or weaker acid) is added to hold the strength at 98–98.5 %; the acid is pumped through anodically protected shell-and-tube coolers back to the towers, and the net make is withdrawn as product. Absorption in 98.5 % acid (not water) is used because SO₃ reacting directly with water forms a stable fog that is almost impossible to absorb.
  8. Tail gas. The tail gas, now with less than about 200–300 ppm SO₂, is discharged through a stack. Single-absorption plants need scrubbing (e.g. with ammonia or caustic) to meet emission limits.

Major engineering problems

Equilibrium vs rate in the converter

Exothermic reversible reaction: use several adiabatic beds with interbed cooling and intermediate SO₃ removal (DCDA) so that each bed operates near the optimum temperature.

Corrosion

Use 98–98.5 % acid (least corrosive to steel), alloy/cast-iron acid piping, brick-lined towers, PTFE/stainless steel distributors and anodically protected acid coolers; keep the gas dry.

Acid mist and SO₂ emission

Dry the air thoroughly, absorb in 98.5 % acid, install candle fibre mist eliminators and use DCDA (or tail-gas scrubbing).

Catalyst poisoning and dusting

Arsenic, fluorine, chlorine and dust (pyrites and smelter gas) poison or plug V₂O₅ beds — clean the gas by cyclones, electrostatic precipitators, scrubbers and wet ESP; sieve catalyst periodically.

Heat recovery

About 5.5 GJ of heat per tonne of acid is released; waste-heat boilers, superheaters and economisers export HP steam to run turbines or nearby fertiliser plants.

Notes

  • Chamber (lead chamber) process using nitrogen oxides gave only 60–78 % acid and is obsolete.
  • Oleum is made by absorbing SO₃ in 98 % acid in a separate oleum tower; dilution of oleum with water gives acid of any strength.
  • Production capacity is usually quoted as tonnes per day of 100 % H₂SO₄ (MTPD).
  • From the stoichiometry S + 1.5O₂ + H₂O → H₂SO₄, 1 t of sulphur gives 98/32 ≈ 3.06 t of acid.

Practice questions

In the contact process SO₃ is absorbed in

  1. water
  2. 98–98.5 % H₂SO₄
  3. dilute H₂SO₄
  4. oleum only
Show the answer

Answer: B. 98–98.5 % H₂SO₄ SO₃ with water forms a fog of acid mist that is hard to absorb; 98.5 % acid absorbs it completely.

The catalyst used in modern sulphuric acid converters is

  1. platinum gauze
  2. V₂O₅ promoted with K₂SO₄
  3. iron oxide
  4. nickel
Show the answer

Answer: B. V₂O₅ promoted with K₂SO₄ Vanadium catalyst is cheaper and resistant to poisons compared with Pt.

Why is gas cooled between catalyst beds?

  1. to condense SO₃
  2. the oxidation is exothermic and reversible, so lower temperature raises equilibrium conversion
  3. to save catalyst
  4. to remove water
Show the answer

Answer: B. the oxidation is exothermic and reversible, so lower temperature raises equilibrium conversion Adiabatic temperature rise lowers the equilibrium conversion; interbed cooling restores it.

DCDA plants achieve an overall SO₂ conversion of about

  1. 90 %
  2. 95 %
  3. 98 %
  4. 99.7 %
Show the answer

Answer: D. 99.7 % Intermediate absorption shifts the equilibrium in the last bed.

Air for sulphur burning is dried with

  1. silica gel
  2. concentrated sulphuric acid
  3. CaCl₂
  4. molecular sieves
Show the answer

Answer: B. concentrated sulphuric acid A packed drying tower irrigated with 93–98 % acid.

Oleum is

  1. dilute H₂SO₄
  2. SO₃ dissolved in H₂SO₄ (H₂S₂O₇)
  3. SO₂ in water
  4. sulphur trioxide gas
Show the answer

Answer: B. SO₃ dissolved in H₂SO₄ (H₂S₂O₇) Fuming sulphuric acid.

Theory questions

Why is SO₃ not absorbed directly in water? (2 marks)

Show the model answer

SO₃ reacts with water vapour in the gas phase to form a fine mist of H₂SO₄ droplets which passes through absorbers and is very difficult to remove. Absorption in 98–98.5 % acid (which has the lowest vapour pressure of water and SO₃) is complete.

Explain with a flow diagram the manufacture of sulphuric acid by the DCDA process. (10 marks)

Show the model answer

Dry air (drying tower with 98 % acid) burns molten sulphur at 1000–1150 °C to 10–11 % SO₂; a waste-heat boiler cools the gas to ≈ 420 °C. In a four-bed V₂O₅ converter with interbed cooling ≈ 95 % conversion is reached after three beds; SO₃ is absorbed in an intermediate absorber (98.5 % acid), the gas is reheated and the fourth bed gives > 99.7 % overall conversion. A final absorber removes the remaining SO₃; acid strength is held by adding water, coolers remove the heat, product acid is withdrawn and tail gas goes to the stack.

Discuss the major engineering problems of a sulphuric acid plant and their solutions. (5 marks)

Show the model answer

Equilibrium limitation (multi-bed, interbed cooling, DCDA); corrosion (98 % acid, alloy and anodically protected coolers, dry gas); acid mist and SO₂ emission (dry air, mist eliminators, DCDA/scrubbing); catalyst poisoning (gas cleaning for pyrites/smelter gas); heat recovery (waste-heat boilers, superheaters, economisers for HP steam).

Frequently asked questions

How is sulphuric acid manufactured?

Double contact – double absorption (DCDA) process. Sulphuric acid is the most produced chemical in the world and its consumption is an index of a country’s industrial activity. Modern plants burn molten sulphur in dry air to SO₂, oxidise it over vanadium pentoxide catalyst in a multi-bed converter, and absorb the SO₃ in 98–98.5 % acid. In the double contact – double absorption (DCDA) scheme, SO₃ is removed after the third bed so that the equilibrium in the fourth bed is pushed further, giving 99.7–99.9 % overall conversion and very low SO₂ emission. The strongly exothermic reactions make the plant a net exporter of high-pressure steam.

What raw materials are used to make sulphuric acid?

Elemental sulphur (from Claus units of refineries and gas plants, or Frasch mining); Alternative SO₂ sources: iron pyrites (FeS₂) roasting, smelter off-gases (Cu, Zn), spent acid regeneration; Air (dried) and process water

What catalyst is used in sulphuric acid production?

V₂O₅ promoted with K₂SO₄ on silica

What is sulphuric acid used for?

Phosphatic fertilisers (phosphoric acid, SSP) and ammonium sulphate — about 60 % of demand; Petroleum refining (alkylation), steel pickling; Detergents (sulphonation), titanium dioxide pigments, rayon, lead-acid batteries, explosives (nitration mixtures)

Watch the animated P&ID →