IITIAN1997 STUDIO

Epoxy Resins

Bisphenol-A + epichlorohydrin (DGEBA) and curing

Watch the animated P&ID →

Epoxy resins are thermosetting polymers with reactive epoxide (oxirane) groups. The most common, diglycidyl ether of bisphenol-A (DGEBA), is made by reacting bisphenol-A with excess epichlorohydrin in the presence of sodium hydroxide, which also removes HCl as salt. Liquid resins (n ≈ 0.1–0.2) are used for coatings, composites and adhesives; higher-molecular-weight solid resins (n up to 25) are made by the "taffy" or advancement process. Cured with amines or anhydrides, epoxies give hard, chemically resistant, strongly adhesive networks.

Raw materials

  • Bisphenol-A (from phenol + acetone)
  • Epichlorohydrin (from propylene/allyl chloride or glycerol)
  • Caustic soda
  • Solvents (toluene, MIBK) for washing
  • Curing agents: aliphatic amines (DETA, TETA), polyamides, anhydrides

Products

  • Liquid epoxy resin (EEW 182–192 g/eq)
  • Solid epoxy resins (EEW 450–4000)
  • Formulated systems: coatings, adhesives, laminates

Uses

  • Protective and marine coatings, powder coatings, can linings
  • Fibre-reinforced composites (wind blades, aircraft), printed circuit boards
  • Structural adhesives, flooring, electrical encapsulation

Reactions

  • BPA + 2 ECH (+ NaOH) → DGEBA + 2NaCl + 2H₂O (coupling then dehydrochlorination)
  • Chain extension: n ≈ 0–25 repeating hydroxypropyl ether units
  • Amine cure: R–NH₂ + epoxide → R–NH–CH₂–CH(OH)– (cross-linking)
  • Epoxy equivalent weight (EEW) = g resin per mole of epoxide

Operating conditions

ECH : BPA mole ratio≈ 10 : 1 for liquid resins (low n)
Reaction60–100 °C, NaOH added gradually, water removed azeotropically
ECH recoveryVacuum distillation and recycle
Salt removalDissolving in solvent, water washing, separation
ProductViscosity 11–15 Pa·s at 25 °C (liquid DGEBA)

Process, step by step

  1. Charging. Bisphenol-A is dissolved in a large excess of epichlorohydrin in a glass-lined or stainless-steel reactor. The excess favours low-molecular-weight (n ≈ 0) diglycidyl ether.
  2. Coupling and dehydrochlorination. Aqueous sodium hydroxide is added slowly at 60–100 °C. The phenolic groups open the epoxide ring of ECH (coupling) and NaOH then closes a new epoxide by removing HCl as NaCl. Water is removed by azeotropic distillation with ECH under reduced pressure to keep the reaction selective.
  3. Epichlorohydrin recovery. After reaction, excess ECH is distilled off under vacuum, condensed and recycled to the next batch.
  4. Washing and salt removal. The crude resin is dissolved in a solvent (toluene or MIBK), treated with a little more caustic to complete ring closure, and washed with water to remove NaCl; phases are separated in a decanter.
  5. Solvent stripping and finishing. The solvent is stripped under vacuum and recycled, leaving liquid epoxy resin, which is filtered and drummed. Solid resins are made by reacting liquid resin with further BPA (advancement) and flaking.

Major engineering problems

Toxicity of epichlorohydrin

Closed handling, vapour recovery, operator protection (probable carcinogen).

Control of molecular weight and EEW

ECH : BPA ratio, caustic addition rate and temperature.

Hydrolysable chlorine in resin

Complete dehydrochlorination with extra caustic treatment.

Salt and waste water

Efficient washing, brine treatment and reuse.

Exothermic curing (in use)

Controlled mixing ratios and pot life; heat sinks in large castings.

Notes

  • Epoxy resins are thermoplastic before cure and thermoset after cure.
  • Novolac epoxies (from phenol–formaldehyde novolacs) give higher cross-link density and heat resistance.
  • Stoichiometric amine content = (amine H equivalent weight / EEW) × 100 phr.

Practice questions

DGEBA epoxy resin is made from

  1. phenol + formaldehyde
  2. bisphenol-A + epichlorohydrin
  3. urea + formaldehyde
  4. styrene + maleic anhydride
Show the answer

Answer: B. bisphenol-A + epichlorohydrin With NaOH.

The role of NaOH in epoxy manufacture is

  1. catalyst only
  2. coupling and dehydrochlorination (removes HCl as NaCl)
  3. curing agent
  4. solvent
Show the answer

Answer: B. coupling and dehydrochlorination (removes HCl as NaCl) Closes the epoxide ring.

A large excess of epichlorohydrin gives

  1. high-MW solid resin
  2. low-MW liquid resin
  3. no reaction
  4. cross-linked gel
Show the answer

Answer: B. low-MW liquid resin n ≈ 0.1–0.2.

Epoxy resins are cured with

  1. sulphur
  2. amines or anhydrides
  3. peroxides only
  4. water
Show the answer

Answer: B. amines or anhydrides Cross-linking.

EEW means

  1. epoxy equivalent weight
  2. effective epoxide work
  3. ester exchange weight
  4. epoxide evaporation weight
Show the answer

Answer: A. epoxy equivalent weight g resin per epoxide group.

Theory questions

Describe the manufacture of epoxy resin with reactions. (6 marks)

Show the model answer

BPA + excess ECH with gradual NaOH at 60–100 °C: coupling and dehydrochlorination giving DGEBA + NaCl + H₂O; azeotropic water removal; ECH vacuum recovery; solvent dissolution, caustic treatment and water washing; brine separation; solvent stripping; liquid resin (EEW ≈ 185); advancement with BPA for solid resins; curing with amines.

Frequently asked questions

How is epoxy resins manufactured?

Bisphenol-A + epichlorohydrin (DGEBA) and curing. Epoxy resins are thermosetting polymers with reactive epoxide (oxirane) groups. The most common, diglycidyl ether of bisphenol-A (DGEBA), is made by reacting bisphenol-A with excess epichlorohydrin in the presence of sodium hydroxide, which also removes HCl as salt. Liquid resins (n ≈ 0.1–0.2) are used for coatings, composites and adhesives; higher-molecular-weight solid resins (n up to 25) are made by the "taffy" or advancement process. Cured with amines or anhydrides, epoxies give hard, chemically resistant, strongly adhesive networks.

What raw materials are used to make epoxy resins?

Bisphenol-A (from phenol + acetone); Epichlorohydrin (from propylene/allyl chloride or glycerol); Caustic soda; Solvents (toluene, MIBK) for washing; Curing agents: aliphatic amines (DETA, TETA), polyamides, anhydrides

What catalyst is used in epoxy resins production?

sodium hydroxide (coupling and dehydrochlorination)

What is epoxy resins used for?

Protective and marine coatings, powder coatings, can linings; Fibre-reinforced composites (wind blades, aircraft), printed circuit boards; Structural adhesives, flooring, electrical encapsulation

Watch the animated P&ID →