IITIAN1997 STUDIO

Diammonium Phosphate (DAP)

Pre-neutraliser / pipe reactor + ammoniator–granulator

Watch the animated P&ID →

Diammonium phosphate (NH₄)₂HPO₄, sold as 18-46-0, is the most popular complex fertiliser in India. Phosphoric acid is partially neutralised with ammonia in a pre-neutraliser or pipe reactor to a mole ratio of about 1.4–1.5, and the hot slurry is sprayed onto a rolling bed of recycled granules in a rotary ammoniator–granulator, where more ammonia brings the ratio to 1.8–2.0. Granules are dried, screened, cooled and coated; fines and crushed oversize are recycled. The same plant can make MAP and NPK grades.

Raw materials

  • Phosphoric acid 40–54 % P₂O₅ (wet process)
  • Ammonia (liquid or gas)
  • Sulphuric acid (for grade control and scrubbing)
  • Coating oil / anti-caking agent

Products

  • DAP 18 % N, 46 % P₂O₅
  • MAP 11-52-0, NPK grades (10:26:26, 12:32:16) in the same plant

Uses

  • Basal fertiliser supplying N and P
  • Fire retardant, yeast nutrient (technical grade)

Reactions

  • H₃PO₄ + NH₃ → NH₄H₂PO₄ (MAP) ΔH ≈ −134 kJ/mol
  • NH₄H₂PO₄ + NH₃ → (NH₄)₂HPO₄ (DAP)
  • H₂SO₄ + 2NH₃ → (NH₄)₂SO₄ (when adjusting N)

Operating conditions

Pre-neutraliserNH₃ : H₃PO₄ mole ratio 1.4–1.5 (maximum solubility), 115–125 °C
GranulatorFinal mole ratio 1.8–2.0; recycle ratio 3–5 : 1
DryerCo-current rotary dryer, product ≈ 85–95 °C, moisture < 1.5 %
Product size2–4 mm granules
ScrubbingPhosphoric/sulphuric acid scrubbers recover NH₃

Process, step by step

  1. Acid and ammonia feed. Phosphoric acid (often combined with scrubber liquor) is pumped from storage; ammonia is fed as liquid or vapour. Accurate ratio control is essential because the solubility of ammonium phosphates depends strongly on the NH₃ : H₃PO₄ mole ratio.
  2. Pre-neutralisation. In the pre-neutraliser tank (or a pipe reactor) acid is reacted with ammonia to a mole ratio of 1.4–1.5, where the slurry has maximum solubility and stays fluid with only 15–20 % water. The heat of reaction evaporates much of the water.
  3. Ammoniation–granulation. The slurry is sprayed onto a rolling bed of recycled undersize and crushed oversize granules in the rotary drum; ammonia is injected under the bed through a sparger to complete the reaction to DAP (mole ratio 1.8–2.0). Particles grow by layering into round granules.
  4. Drying. Granules are dried in a co-current rotary dryer with hot gas from an oil/gas burner to below 1.5 % moisture. Over-drying would decompose DAP and release ammonia.
  5. Screening, crushing and recycle. Double-deck screens separate oversize (crushed in chain mills and recycled), undersize (recycled directly) and on-size product. Recycle controls granulation moisture.
  6. Cooling, coating and storage. On-size granules are cooled in a rotary or fluid-bed cooler and coated with oil and an anti-caking agent to prevent caking during storage, then bagged.
  7. Scrubbing. Ammonia and fluorine in the off-gases of the pre-neutraliser, granulator and dryer are scrubbed with phosphoric acid; the liquor returns to the pre-neutraliser, recovering nutrients.

Major engineering problems

Ammonia losses

Pre-neutraliser at maximum-solubility mole ratio, acid scrubbers recycling liquor, good sparger design.

Granulation control

Recycle ratio, slurry water content and temperature control; on-line size analysis.

Caking and dust

Proper drying and cooling, coating with oil/amines, closed handling.

Corrosion and scaling

Stainless steel, rubber-lined scrubbers, periodic cleaning of sparger and reactor scale.

Fluorine emission

Scrubbing; most F reports to the product.

Notes

  • Pure (NH₄)₂HPO₄ is 21.2 % N and 53.8 % P₂O₅; commercial 18-46 reflects impurities in wet-process acid.
  • India imports much of its DAP and phosphoric acid; DAP is subsidised under the Nutrient Based Subsidy scheme.
  • Pipe (tubular) reactors allow use of weaker acid and save energy.

Practice questions

DAP grade is

  1. 46-0-0
  2. 18-46-0
  3. 11-52-0
  4. 0-46-0
Show the answer

Answer: B. 18-46-0 18 % N, 46 % P₂O₅.

The pre-neutraliser operates near a NH₃ : H₃PO₄ mole ratio of

  1. 0.5
  2. 1.0
  3. 1.45
  4. 3.0
Show the answer

Answer: C. 1.45 Maximum solubility of the slurry.

Ammonia off-gases in a DAP plant are scrubbed with

  1. water only
  2. phosphoric acid
  3. caustic soda
  4. lime
Show the answer

Answer: B. phosphoric acid Liquor is recycled.

Oversize granules are

  1. discarded
  2. crushed and recycled
  3. sold separately
  4. dissolved
Show the answer

Answer: B. crushed and recycled Recycle controls granulation.

Monoammonium phosphate (MAP) forms at a mole ratio of

  1. 1
  2. 2
  3. 3
  4. 0.5
Show the answer

Answer: A. 1 NH₄H₂PO₄.

Theory questions

Describe the manufacture of DAP with a flow sheet. (8 marks)

Show the model answer

Phosphoric acid + NH₃ in pre-neutraliser (MR 1.4–1.5, 120 °C); slurry to rotary ammoniator–granulator with recycle and NH₃ sparger (MR 1.8–2.0); rotary dryer; screens — oversize crushed, undersize recycled; cooler; coating; scrubbers with H₃PO₄ returning liquor.

Why is a recycle of fines necessary in DAP granulation? (3 marks)

Show the model answer

Recycled solids absorb the slurry water so that the bed has the right liquid phase for granule growth; they control granule size and moisture, and return fines and crushed oversize to the product.

Frequently asked questions

How is diammonium phosphate (dap) manufactured?

Pre-neutraliser / pipe reactor + ammoniator–granulator. Diammonium phosphate (NH₄)₂HPO₄, sold as 18-46-0, is the most popular complex fertiliser in India. Phosphoric acid is partially neutralised with ammonia in a pre-neutraliser or pipe reactor to a mole ratio of about 1.4–1.5, and the hot slurry is sprayed onto a rolling bed of recycled granules in a rotary ammoniator–granulator, where more ammonia brings the ratio to 1.8–2.0. Granules are dried, screened, cooled and coated; fines and crushed oversize are recycled. The same plant can make MAP and NPK grades.

What raw materials are used to make diammonium phosphate (dap)?

Phosphoric acid 40–54 % P₂O₅ (wet process); Ammonia (liquid or gas); Sulphuric acid (for grade control and scrubbing); Coating oil / anti-caking agent

What catalyst is used in diammonium phosphate (dap) production?

no catalyst (acid–base neutralisation)

What is diammonium phosphate (dap) used for?

Basal fertiliser supplying N and P; Fire retardant, yeast nutrient (technical grade)

Watch the animated P&ID →