IITIAN1997 STUDIO

Portland Cement

Dry process with suspension preheater, precalciner and rotary kiln

Watch the animated P&ID →

Portland cement is a hydraulic binder made by burning a finely ground, accurately proportioned mixture of limestone (lime) and clay or shale (silica, alumina, iron oxide) to partial fusion at about 1450 °C. The resulting nodules, called clinker, are cooled and ground with 3–5 % gypsum, which controls setting. Modern plants use the energy-efficient dry process: the raw meal is preheated by kiln exhaust in a 4–6 stage cyclone preheater, about 90 % calcined in a separately fired precalciner, and burnt in a short rotary kiln. India is the world’s second largest cement producer.

Raw materials

  • Calcareous: limestone, chalk, marl, sea shells (CaCO₃) — ≈ 1.5 t per t clinker
  • Argillaceous: clay, shale, slate (SiO₂, Al₂O₃, Fe₂O₃)
  • Correctives: bauxite/laterite (Al₂O₃, Fe₂O₃), iron ore, sand
  • Gypsum (CaSO₄·2H₂O) 3–5 % at grinding
  • Fuel: pulverised coal, petcoke, alternative fuels (tyres, RDF)
  • Pozzolanas / slag for blended cements (fly ash, granulated blast-furnace slag)

Products

  • Ordinary Portland Cement (OPC grades 33, 43, 53)
  • Portland Pozzolana Cement (PPC) and Portland Slag Cement (PSC)
  • Special cements (white, sulphate resisting, low heat, rapid hardening, oil-well)

Uses

  • Concrete and mortar for buildings, roads, bridges and dams
  • Precast products, pipes, sleepers
  • Oil-well cementing, grouting

Reactions

  • CaCO₃ → CaO + CO₂ ΔH = +178 kJ/mol (calcination, 800–900 °C)
  • 2CaO + SiO₂ → 2CaO·SiO₂ (C₂S, belite) 900–1200 °C
  • 3CaO + Al₂O₃ → 3CaO·Al₂O₃ (C₃A); 4CaO + Al₂O₃ + Fe₂O₃ → C₄AF 1200–1300 °C (liquid phase)
  • C₂S + CaO → 3CaO·SiO₂ (C₃S, alite) 1300–1450 °C
  • Hydration: 2C₃S + 6H → C₃S₂H₃ (C–S–H gel) + 3Ca(OH)₂

Operating conditions

Preheater4–6 cyclone stages; gas 1000 → 300 °C, meal heated to ≈ 800 °C
Precalciner850–900 °C, 55–60 % of fuel, 90–95 % calcination
Rotary kilnBurning zone ≈ 1450 °C (flame ≈ 2000 °C), slope 3–4 %, 3–5 rpm, L/D ≈ 15
Clinker coolerGrate cooler: clinker 1400 → ≈ 100 °C
Heat consumption≈ 700–750 kcal/kg clinker (dry); 1300–1600 (wet process)
Fineness300–350 m²/kg Blaine (OPC 53)

Process, step by step

  1. Quarrying and crushing. Limestone is blasted in the quarry, transported by dumpers and reduced to below 75 mm in jaw/impact or hammer crushers. Clay and correctives are crushed separately. The materials are pre-blended in longitudinal or circular stockpiles (stacker–reclaimer) to even out chemical variation.
  2. Raw meal grinding and drying. Limestone, clay and correctives are proportioned by weigh feeders (controlled by on-line X-ray analysis) and ground in a vertical roller mill to ≈ 10–15 % residue on 90 µm. Hot kiln exhaust gas sweeps through the mill, drying the meal and carrying it to separators.
  3. Homogenisation. The raw meal is stored in a continuous blending silo where air fluidisation mixes it so that the lime saturation factor varies only within narrow limits — essential for stable kiln operation and uniform clinker.
  4. Cyclone preheater. Meal is fed into the riser duct of the top cyclone stage and travels down through four to six cyclones in counter-current with hot kiln gases rising from below. Heat transfer in suspension is extremely fast: the meal reaches about 800 °C while the gases cool from 1000 °C to about 300 °C. Moisture is driven off and clay minerals dehydrate.
  5. Precalciner. Before the bottom cyclone the meal enters the precalciner, a vessel in which 55–60 % of the total fuel is burnt with tertiary air from the cooler. Most of the calcination CaCO₃ → CaO + CO₂ (the most energy-consuming step) is completed here at 850–900 °C, so the meal enters the kiln about 90–95 % calcined. This allows short, high-capacity kilns (up to 10 000 t/day).
  6. Rotary kiln (clinkering). The inclined, refractory-lined rotary kiln turns slowly; the meal moves down toward the burner. In the transition zone C₂S forms; at 1250–1300 °C about 20–25 % of the charge melts (C₃A, C₄AF flux), and in the burning zone at ≈ 1450 °C C₂S reacts with free lime to give alite (C₃S). The partially fused material agglomerates into nodules — clinker. Coating of the refractory protects the lining.
  7. Clinker cooling. Clinker falls onto a reciprocating grate cooler where fans blow ambient air through the bed. Rapid cooling freezes alite (preventing its decomposition to C₂S), keeps MgO as fine periclase and makes clinker easier to grind. The hot air is reused as secondary air for the kiln burner and tertiary air for the precalciner; excess air goes through a dust collector.
  8. Cement grinding and dispatch. Clinker is stored, then ground with 3–5 % gypsum (and fly ash or slag for PPC/PSC) in closed-circuit ball mills or roller presses with high-efficiency separators to the required fineness. Gypsum retards the flash setting caused by C₃A. Cement is stored in silos and packed in 50 kg bags or dispatched in bulk.
  9. Gas cleaning and fuel preparation. Coal is dried and pulverised in a coal mill. Kiln exhaust is drawn by the ID fan through the raw mill (or a conditioning tower) and cleaned in bag filters or electrostatic precipitators to below 30 mg/Nm³ dust before the stack; collected dust returns to the process.

Major engineering problems

Huge CO₂ emission (≈ 0.8–0.9 t per t clinker)

About 60 % comes from calcination: blended cements (PPC/PSC), alternative fuels, efficient kilns, waste-heat recovery power and carbon capture.

Dust pollution

Bag filters/ESPs on kiln, mills, coolers and packers; enclosed conveyors.

Kiln rings, coating and refractory failure

Uniform raw meal (blending), controlled sulphur/alkali/chloride (kiln bypass), proper burner flame shape, good refractory selection.

High energy consumption

Dry process with 5–6 stage preheaters and precalciner, grate coolers, roller presses/VRMs, high-efficiency separators, waste-heat power generation.

NOx and SO₂ emissions

Staged combustion in the calciner, SNCR with ammonia/urea, low-sulphur fuels; most SO₂ is absorbed by the lime in the process.

Quality variation

On-line cross-belt and X-ray analysers controlling LSF, SM and AM.

Notes

  • Lime saturation factor LSF = CaO/(2.8SiO₂ + 1.2Al₂O₃ + 0.65Fe₂O₃) ≈ 0.92–0.98; silica modulus SM = SiO₂/(Al₂O₃ + Fe₂O₃) ≈ 2.3–2.7; alumina modulus AM = Al₂O₃/Fe₂O₃ ≈ 1.3–2.5.
  • Bogue: C₃S = 4.071C − 7.600S − 6.718A − 1.430F − 2.852SO₃; C₂S = 2.867S − 0.7544C₃S; C₃A = 2.650A − 1.692F; C₄AF = 3.043F.
  • Typical OPC oxides: CaO 60–67 %, SiO₂ 17–25 %, Al₂O₃ 3–8 %, Fe₂O₃ 0.5–6 %, MgO 0.1–4 % (limit 6 %), SO₃ 1–3 %.
  • Wet process (slurry with 35–40 % water, long kilns) is obsolete because of its high fuel use; semi-dry (Lepol) also exists.
  • Setting: initial ≥ 30 min, final ≤ 600 min (IS 4031); soundness by Le Chatelier and autoclave tests.
  • Grades 33/43/53 = minimum 28-day compressive strength in MPa.

Practice questions

The main compound responsible for the early strength of Portland cement is

  1. C₂S
  2. C₃S
  3. C₃A
  4. C₄AF
Show the answer

Answer: B. C₃S Alite hydrates quickly.

Gypsum is added to clinker to

  1. increase strength
  2. retard the flash setting of C₃A
  3. give colour
  4. reduce fineness
Show the answer

Answer: B. retard the flash setting of C₃A 3–5 % gypsum controls setting.

The burning-zone temperature in a cement kiln is about

  1. 800 °C
  2. 1000 °C
  3. 1450 °C
  4. 2000 °C
Show the answer

Answer: C. 1450 °C Partial fusion to clinker.

Most of the calcination in a modern dry-process plant takes place in the

  1. raw mill
  2. precalciner
  3. cooler
  4. cement mill
Show the answer

Answer: B. precalciner 90–95 % calcination before the kiln.

Sulphate-resisting cement has a low content of

  1. C₃S
  2. C₂S
  3. C₃A
  4. C₄AF
Show the answer

Answer: C. C₃A C₃A < 5 %.

White cement requires raw materials low in

  1. CaO
  2. SiO₂
  3. Fe₂O₃
  4. Al₂O₃
Show the answer

Answer: C. Fe₂O₃ Iron gives the grey colour.

Lime saturation factor of a good raw mix lies between

  1. 0.66–0.80
  2. 0.92–0.98
  3. 1.2–1.5
  4. 2.3–2.7
Show the answer

Answer: B. 0.92–0.98 2.3–2.7 is the silica modulus.

Low-heat cement contains a high proportion of

  1. C₃S
  2. C₂S
  3. C₃A
  4. free lime
Show the answer

Answer: B. C₂S Belite hydrates slowly with less heat.

Theory questions

Why is gypsum added to cement clinker? (2 marks)

Show the model answer

C₃A reacts very rapidly with water causing flash set; gypsum (3–5 %) reacts with C₃A to form ettringite on its surface, retarding hydration so that cement can be placed and compacted.

Describe with a flow diagram the dry process of Portland cement manufacture. (10 marks)

Show the model answer

Quarrying, crushing, pre-blending; proportioning and grinding in VRM with hot gas; homogenising silo; 4–6 stage cyclone preheater; precalciner (60 % fuel, 90 % calcination); rotary kiln burning zone 1450 °C forming C₃S, C₂S, C₃A, C₄AF; grate cooler (heat recovered as secondary/tertiary air); clinker silo; ball mill grinding with 4 % gypsum; silos and packing; bag filters/ESP, coal mill.

Give the composition and properties of the major compounds in Portland cement. (5 marks)

Show the model answer

C₃S 50–70 % early strength, high heat; C₂S 15–30 % late strength, low heat; C₃A 5–10 % flash set, poor sulphate resistance; C₄AF 5–15 % flux, colour. Typical oxides CaO 60–67, SiO₂ 17–25, Al₂O₃ 3–8, Fe₂O₃ 0.5–6 %.

Write short notes on special cements. (6 marks)

Show the model answer

Rapid hardening (more C₃S, finer), low heat (more C₂S, less C₃A, dams), sulphate resisting (C₃A < 5 %), PPC (15–35 % fly ash), PSC (slag), white (low iron), high alumina (bauxite + lime, refractory), oil-well (retarded, high T/P).

Frequently asked questions

How is portland cement manufactured?

Dry process with suspension preheater, precalciner and rotary kiln. Portland cement is a hydraulic binder made by burning a finely ground, accurately proportioned mixture of limestone (lime) and clay or shale (silica, alumina, iron oxide) to partial fusion at about 1450 °C. The resulting nodules, called clinker, are cooled and ground with 3–5 % gypsum, which controls setting. Modern plants use the energy-efficient dry process: the raw meal is preheated by kiln exhaust in a 4–6 stage cyclone preheater, about 90 % calcined in a separately fired precalciner, and burnt in a short rotary kiln. India is the world’s second largest cement producer.

What raw materials are used to make portland cement?

Calcareous: limestone, chalk, marl, sea shells (CaCO₃) — ≈ 1.5 t per t clinker; Argillaceous: clay, shale, slate (SiO₂, Al₂O₃, Fe₂O₃); Correctives: bauxite/laterite (Al₂O₃, Fe₂O₃), iron ore, sand; Gypsum (CaSO₄·2H₂O) 3–5 % at grinding; Fuel: pulverised coal, petcoke, alternative fuels (tyres, RDF); Pozzolanas / slag for blended cements (fly ash, granulated blast-furnace slag)

What catalyst is used in portland cement production?

no catalyst (high-temperature solid-state reactions)

What is portland cement used for?

Concrete and mortar for buildings, roads, bridges and dams; Precast products, pipes, sleepers; Oil-well cementing, grouting

Watch the animated P&ID →