Manufacturing Methods
Topics: Casting, forming, machining, joining and advanced manufacturing methods.
Classifying manufacturing processes
Manufacturing turns raw materials into useful products. Processes fall into a few families. Casting pours molten material into a mould shaped like the part. Forming changes the shape of solid material by force without removing any (forging, rolling, extrusion, drawing, sheet-metal bending and pressing). Machining removes material as chips with a cutting tool (turning, milling, drilling, grinding). Joining connects parts (welding, brazing, soldering, adhesives, fasteners). Finishing improves the surface (polishing, painting, plating).
Most products pass through several processes: a crankshaft is forged, machined, heat-treated and ground; a phone case is injection-moulded and painted. Choosing processes depends on the material, shape and size, the quantity required, the accuracy and surface finish needed, and cost. Casting and moulding suit complex shapes in large numbers; forming gives strong parts with good grain flow; machining gives the best accuracy but wastes material.
Material utilisation (the fraction of the starting material that ends up in the part) and the number of operations both drive cost. Near-net-shape processes (precision casting, forging, moulding, additive manufacturing) produce parts close to final size, cutting machining and waste.
- Casting, forming, machining, joining, finishing
- Real parts use several processes
- Choose by material, shape, quantity, accuracy, cost
- Machining: accurate but wasteful
- Near-net shape reduces waste and machining
Example: Suggest the main process for: (a) a plastic bottle cap; (b) a cast-iron engine block; (c) a steel spanner; (d) a hole in a steel plate.
- (a) Injection moulding; (b) sand casting.
- (c) Forging (then finishing); (d) drilling.
Answer: Moulding, casting, forging, drilling
Example: A 100 g steel bar is machined into a 60 g part. Find the material utilisation, and suggest how to improve it.
- Utilisation = 60/100 = 60 %; 40 g becomes chips.
- Start from a forged or cast blank closer to final shape (near net shape).
Answer: 60 %; use a near-net-shape blank
Casting and forming
Casting can make large and complex shapes, including internal cavities (using cores), in almost any metal. Sand casting is cheap and flexible; die casting forces molten aluminium or zinc into steel dies for accurate parts in large numbers; investment casting gives fine detail for turbine blades and jewellery. Typical defects are shrinkage cavities, gas porosity and inclusions.
Forming relies on plastic deformation. In bulk forming (forging, rolling, extrusion, wire drawing) the volume stays constant while the shape changes, which gives simple calculations: if a billet is upset to a shorter height, its cross-section grows in proportion. Hot working (above recrystallisation temperature) needs less force; cold working gives better finish, accuracy and strength through work hardening.
Sheet-metal forming (shearing, bending, deep drawing, spinning) makes car bodies, cabinets, ducts and utensils. Bends need a minimum radius to avoid cracking, and parts spring back slightly after bending, so tools over-bend a little.
- Casting: complex shapes, cores; sand, die, investment
- Forming: plastic deformation; volume constant
- Hot working (less force) vs cold working (finish, strength)
- Forging, rolling, extrusion, drawing
- Sheet metal: shear, bend (springback), draw
Example: A billet 50 mm in diameter and 100 mm long is upset-forged to 40 mm height. Find its new diameter (ignore barrelling).
- Volume is constant: d₁²h₁ = d₂²h₂.
- d₂ = 50 × √(100/40) = 50 × 1.581 = 79.1 mm.
Answer: About 79 mm
Example: A 20 mm thick plate 1 m long is rolled to 15 mm with no change in width. Find the new length and the reduction.
- Volume constant: 20 × 1 = 15 × L ⇒ L = 1.333 m.
- Reduction in thickness = (20 − 15)/20 = 25 %.
Answer: 1.33 m; 25 % reduction
Machining, joining and tolerances
Machining shapes parts by cutting chips with a harder tool. Turning on a lathe makes round parts, milling makes flat faces, slots and pockets, drilling makes holes, and grinding gives fine finish and accuracy. The cutting speed V = πDN/1000 m/min (D in mm, N in rpm) must suit the tool and work materials; feed and depth of cut set how fast material is removed.
No part can be made to an exact size, so drawings specify tolerances: the permitted variation between upper and lower limits. Tolerance = upper limit − lower limit. Mating parts are designed with a fit: a clearance fit always leaves a gap (shafts that turn), an interference fit always overlaps (pressed-in bearings, gears), and a transition fit may do either (accurate location). ISO hole-basis fits such as H7/g6, H7/k6 and H7/p6 are standard.
Joining methods are permanent (welding, brazing, soldering, riveting, adhesives) or detachable (bolts, screws, pins, keys, snap fits). The choice depends on strength, materials, whether the part must be dismantled, appearance and cost.
- Turning, milling, drilling, grinding
- V = πDN/1000 m/min
- Tolerance = upper − lower limit
- Fits: clearance, transition, interference (H7/g6, k6, p6)
- Permanent vs detachable joints
Example: A 25 mm hole is 25.000–25.021 mm and its shaft 24.980–24.993 mm. Find the maximum and minimum clearance and name the fit.
- Max clearance = largest hole − smallest shaft = 25.021 − 24.980 = 0.041 mm.
- Min clearance = smallest hole − largest shaft = 25.000 − 24.993 = 0.007 mm.
- Always positive: a clearance fit (H7/g6).
Answer: 0.041 and 0.007 mm; clearance fit
Example: A 50 mm bar turns at 400 rpm. Find the cutting speed.
- V = πDN/1000 with D in mm and N in rpm.
- V = π × 50 × 400/1000 = 62.8 m/min.
Answer: 62.8 m/min
Advanced manufacturing methods
Advanced (non-traditional) methods remove or add material by means other than a sharp tool, and handle hard materials, complex shapes and tiny features. Electrical discharge machining (EDM) erodes a conducting workpiece with sparks, ideal for hardened dies and sharp internal corners; wire EDM cuts profiles with a moving wire. Electrochemical machining (ECM) dissolves metal anodically without tool wear.
Laser beam machining cuts and engraves sheet metal, plastics and wood with a focused beam; abrasive water-jet cutting uses a high-pressure stream of water and abrasive to cut almost anything, including stone and glass, without heat damage; ultrasonic machining shapes brittle materials such as ceramics. Additive manufacturing (3D printing) builds parts layer by layer from plastics, resins or metal powders.
These methods are slower or costlier per unit than conventional ones for simple parts, so they are chosen when hardness, geometry, heat sensitivity or one-off production makes conventional methods hard. Computer control (CNC) and CAD/CAM link all of them to digital designs.
- EDM and wire EDM: sparks; hard conductive materials
- ECM: dissolves metal; no tool wear
- Laser, water-jet, ultrasonic machining
- Additive manufacturing: layer by layer
- Chosen for hardness, geometry, heat sensitivity, one-offs
Example: Choose a process: (a) a sharp-cornered cavity in a hardened steel die; (b) cutting 50 mm granite slabs to shape; (c) engraving a logo on plywood.
- (a) EDM.
- (b) Abrasive water-jet; (c) laser engraving.
Answer: EDM; water-jet; laser
Example: A laser cuts a part with a 1.2 m perimeter at 2 m/min. How long does the cut take?
- Time = length/speed = 1.2/2 = 0.6 min.
- = 36 s (plus piercing and travel).
Answer: About 36 s
Manufacturing turns raw material into useful shapes. Casting pours molten metal into a mould; forming (forging, rolling, extrusion, sheet-metal work) plastically deforms solid metal; machining removes material with cutting tools; joining (welding, brazing, soldering, fasteners, adhesives) assembles parts; advanced methods include EDM, laser and water-jet cutting, CNC and additive manufacturing. The choice depends on shape, material, quantity, accuracy and cost.
- Casting: complex shapes, large parts (engine blocks).
- Forming: strong parts with good grain flow (crankshafts, sheets).
- Machining: high accuracy and finish (shafts, bores).
- Joining: permanent (welding) or temporary (bolts).
- Advanced: non-traditional machining for hard materials and fine features.
Key formulas
- Tolerance = upper limit − lower limit
Practice questions
Which process removes material?
- casting
- forging
- machining
- welding
Show the answer
Answer: C. machining Chip formation.
Forging is a
- casting process
- forming process
- joining process
- additive process
Show the answer
Answer: B. forming process Plastic deformation.
Tolerance is the
- difference between limits
- nominal size
- surface roughness
- material grade
Show the answer
Answer: A. difference between limits Permissible variation.
EDM is used to machine
- soft wood
- hard conductive metals
- glass only
- rubber
Show the answer
Answer: B. hard conductive metals Spark erosion.
Theory questions
Classify manufacturing processes. (2 marks)
Show the model answer
Casting, forming, machining (material removal), joining, finishing, and additive/advanced processes.
Compare casting and forging. (4 marks)
Show the model answer
Casting: molten metal, complex shapes, possible porosity, lower strength. Forging: solid metal deformed, better grain structure and strength, simpler shapes, needs heavy equipment.
Explain the major manufacturing methods with examples and their selection criteria. (8 marks)
Show the model answer
Describe casting, forming, machining, joining, advanced/additive with examples; criteria: material, shape complexity, size, quantity, accuracy and finish, mechanical properties, cost and lead time.
CNC Machining and Additive Manufacturing
Topics: CNC machining and additive manufacturing.
CNC machines and G-code
A computer numerical control (CNC) machine moves its tool or table along programmed paths using motors on each axis, controlled from a program of instructions. CNC lathes, mills, routers, laser and plasma cutters and 3D printers all work this way. Compared with manual machines they give repeatable accuracy, complex shapes and unattended operation once set up.
The program is usually G-code. Preparatory G-codes set the type of motion: G00 rapid move (not cutting), G01 straight-line cut at feed F, G02 and G03 clockwise and anticlockwise arcs, G20/G21 inch or millimetre units, G90/G91 absolute or incremental coordinates. Miscellaneous M-codes control the machine: M03 spindle on clockwise, M05 spindle stop, M08 coolant on, M30 program end. Coordinates X, Y and Z give the target position, and S sets spindle speed.
Programs are rarely typed by hand now: CAM software generates them from a CAD model and the chosen tools and speeds. Before cutting, the operator sets the work origin (zero point) and tool lengths, and runs a simulation or a “dry run” above the part.
- CNC: motors on axes follow a program
- G00 rapid, G01 line, G02/G03 arcs
- G21 mm, G90 absolute, G91 incremental
- M03 spindle on, M05 stop, M08 coolant, M30 end
- CAM generates code; set the origin; simulate first
Example: What does this program do? G21 G90; G00 X0 Y0; G01 X60 Y0 F200; G01 X60 Y40; G03 X40 Y60 I-20 J0; G01 X0 Y60; G01 X0 Y0.
- Millimetres, absolute; rapid to the origin.
- Cut along the bottom to (60, 0), up to (60, 40), an anticlockwise arc of radius 20 to (40, 60), across to (0, 60) and back to the start.
Answer: It cuts a 60 × 60 mm outline with one rounded corner
Example: How long does G01 X60 Y0 F200 take from the origin?
- Distance 60 mm at 200 mm/min.
- Time = 60/200 = 0.3 min = 18 s.
Answer: 18 s
Cutting speed, feed and machining time
Three parameters govern cutting. Cutting speed V (m/min) is the speed of the work surface past the tool; it depends on the tool and work materials (about 25–30 m/min for HSS on mild steel, 100–200 for carbide, higher for aluminium). Spindle speed follows from it: N = 1000V/(πD). Feed f is how far the tool advances per revolution (mm/rev) in turning or per tooth in milling. Depth of cut d is how deep the tool goes.
Machining time for turning a length L is t = L/(fN). The material removal rate in turning is roughly MRR = V × f × d (with V converted to mm/min). Higher speeds and feeds save time but raise temperature, tool wear and roughness, so roughing passes use large feed and depth and finishing passes use small ones.
Coolants reduce heat and friction and wash chips away. Tools must be sharp and set at centre height on a lathe, and the work must be held rigidly. Never leave the chuck key in the chuck, and keep hands, sleeves and hair away from rotating parts.
- N = 1000V/(πD)
- Turning time t = L/(fN)
- MRR ≈ V f d
- Roughing vs finishing passes
- Coolant, sharp tools, rigid work; remove the chuck key
Example: Turning 40 mm mild steel with a carbide tool at 120 m/min: find N.
- N = 1000V/(πD).
- N = 1000 × 120/(π × 40) = 955 rpm.
Answer: About 955 rpm
Example: A 100 mm length is turned at 500 rpm and 0.2 mm/rev feed, 1 mm deep, on a 50 mm bar. Find the time and MRR.
- t = L/(fN) = 100/(0.2 × 500) = 1 min.
- V = π × 50 × 500/1000 = 78.5 m/min = 78 540 mm/min; MRR ≈ 78 540 × 0.2 × 1 ≈ 15 700 mm³/min.
Answer: 1 min; about 15 700 mm³/min
Additive manufacturing
Additive manufacturing (AM) builds parts layer by layer directly from a 3D model. Material extrusion (FDM) lays down molten filament; vat photopolymerisation (SLA, DLP) cures liquid resin with light; powder bed fusion (SLS for nylon, SLM/DMLS for metals) fuses powder with a laser; material and binder jetting deposit droplets. The workflow is CAD model → STL or 3MF → slicing (layers, supports, infill, tool paths) → printing → post-processing (removing supports, curing, sanding).
AM excels at complex geometry (internal channels, lattices, organic shapes), one-off and customised parts, rapid prototypes, and consolidating assemblies into one piece. It is slower and costlier per part than moulding or machining for large quantities, surfaces show layer lines, and properties depend on direction because layers bond less strongly than material within a layer.
Design for AM: limit overhangs to about 45° or add supports, keep walls at least a few nozzle widths thick, add clearances between moving parts, orient parts so loads run along layers, and hollow or infill large solid regions to save time and material.
- FDM, SLA/DLP, SLS/SLM, jetting
- CAD → STL → slice → print → post-process
- Strengths: complex, custom, consolidated parts
- Limits: speed, cost at volume, layer lines, anisotropy
- Design for AM: overhangs, walls, clearances, orientation
Example: A part needs 20 cm³ of material and the printer deposits about 10 mm³/s. Estimate the print time.
- 20 cm³ = 20 000 mm³.
- Time ≈ 20 000/10 = 2000 s ≈ 33 min (plus travel moves).
Answer: About half an hour
Example: When would you 3D-print rather than injection-mould a part?
- Printing has no tooling cost, so it wins for one-offs, prototypes and customised parts.
- Moulding needs a costly mould but is far cheaper per part in thousands.
Answer: For a few or customised parts; mould for large volumes
In CNC (computer numerical control) machining, a program of G-codes and M-codes drives the axes and spindle, so complex parts are made accurately and repeatably. CAD models are converted to toolpaths with CAM software. Additive manufacturing (3D printing) builds parts layer by layer directly from CAD, ideal for prototypes and complex geometry with little waste.
- G00 rapid move, G01 linear feed, G02/G03 circular interpolation, M03 spindle on, M05 spindle off, M30 end.
- CNC advantages: accuracy, repeatability, complex profiles, less operator skill.
- Additive: FDM, SLA, SLS, DMLS (metal).
- Subtractive vs additive: subtractive wastes material but gives better finish and accuracy.
Key formulas
- Cutting speed V = πDN/1000 m/min
Practice questions
G01 means
- rapid traverse
- linear interpolation at feed
- spindle stop
- program end
Show the answer
Answer: B. linear interpolation at feed Straight cutting move.
M03 turns the spindle
- off
- on clockwise
- on anticlockwise
- to tool change
Show the answer
Answer: B. on clockwise M04 is anticlockwise.
3D printing is an
- additive process
- subtractive process
- forming process
- casting process
Show the answer
Answer: A. additive process Layer by layer.
Cutting speed depends on
- diameter and rpm
- colour
- coolant only
- tool length only
Show the answer
Answer: A. diameter and rpm V = πDN.
Theory questions
What is CNC? (2 marks)
Show the model answer
Computer numerical control: machine tool motion controlled by a program of coded instructions.
Compare additive and subtractive manufacturing. (4 marks)
Show the model answer
Additive builds up material (little waste, complex shapes, slower, rougher, prototypes); subtractive removes material from stock (waste, better accuracy and finish, mass production).
Write the meaning of common G and M codes and outline the CNC workflow from CAD to part. (8 marks)
Show the model answer
Codes as above. Workflow: CAD model → CAM toolpaths, tools, feeds and speeds → post-process to G-code → load and simulate → set workpiece and tool offsets → dry run → machine → inspect.
Fitting Operations and Power Tools
Topics: Fitting operations and power tools.
Fitting tools and operations
Fitting is bench work that shapes and assembles parts by hand. Marking tools include the surface plate, marking blue, scriber, try square, steel rule, odd-leg caliper, divider, surface gauge and centre punch; lines are marked from a filed datum edge. Holding tools are the bench vice (with soft jaws for finished surfaces), clamps and V-blocks.
Cutting tools include the hacksaw, whose blade is fitted with teeth pointing forward so it cuts on the push stroke; choose the blade pitch so that at least three teeth are in contact with the work (finer teeth for thin sheet and tube). Files come in shapes (flat, half-round, round, square, triangular) and cuts (rough, bastard, second cut, smooth); cross filing removes metal quickly and draw filing gives a fine finish. Chisels, scrapers and reamers complete the kit.
Good fitting practice: keep the file flat and use the full stroke, lift on the return, clean files with a file card, never use a file without a handle, and check work often with the try square and gauges.
- Marking: surface plate, blue, scriber, try square, punch
- Holding: vice (soft jaws), clamps, V-blocks
- Hacksaw cuts on the push; ≥ 3 teeth in contact
- Files: shape and cut; cross and draw filing
- Handles on files; check often
Example: Choose a hacksaw blade for 3 mm steel sheet using the three-teeth rule: 24 TPI or 32 TPI?
- Three teeth in 3 mm need a pitch of at most 1 mm.
- 24 TPI gives 25.4/24 = 1.06 mm; 32 TPI gives 0.79 mm.
Answer: 32 TPI (24 TPI is borderline)
Example: Put in order for making a square block: file the datum edge, saw off excess, mark lines, check with try square, file to the line.
- File a datum edge first, then mark from it.
- Saw close to the line, file to the line, check.
Answer: Datum → mark → saw → file → check
Precision measurement: vernier caliper and micrometer
The vernier caliper measures outside, inside and depth dimensions; with 50 vernier divisions matching 49 main-scale millimetres its least count is 0.02 mm. Reading = main-scale reading + (coinciding vernier division × least count), corrected for zero error.
The outside micrometer measures to 0.01 mm. Its spindle screw has a pitch of 0.5 mm, and the thimble has 50 divisions, so least count = pitch/divisions = 0.5/50 = 0.01 mm. Read the sleeve (whole and half millimetres showing) and add the thimble division on the reference line × 0.01 mm. Use the ratchet to apply the same light pressure every time.
Check zero error by closing the instrument: if it reads above zero (positive error), subtract the error; if below zero (negative error), add it. Clean the faces, measure at room temperature, and take several readings.
- Vernier least count 0.02 mm
- Micrometer least count = 0.5/50 = 0.01 mm
- Micrometer: sleeve + thimble × 0.01
- Use the ratchet for even pressure
- Correct zero error: subtract positive, add negative
Example: A micrometer shows 7.5 mm on the sleeve and the 23rd thimble division on the line. Read it; then correct for a zero error of +0.02 mm.
- Reading = 7.5 + 23 × 0.01 = 7.73 mm.
- Corrected = 7.73 − 0.02 = 7.71 mm.
Answer: 7.73 mm; corrected 7.71 mm
Example: Why is a micrometer’s least count 0.01 mm?
- One thimble turn advances the spindle by the 0.5 mm pitch.
- One of 50 divisions is 0.5/50 = 0.01 mm.
Answer: Pitch 0.5 mm ÷ 50 divisions
Drilling, tapping and power tools
Holes are drilled on a bench or pillar drill with twist drills, after centre-punching. Clamp the work (never hold it by hand), choose the spindle speed from the cutting speed, use cutting fluid on steel, and peck (withdraw periodically) to clear chips on deep holes. Drilling time t = depth/(feed × N).
Internal threads are cut with taps (taper, intermediate and bottoming in a set) after drilling a tap-drill hole, about the nominal diameter minus the pitch for metric threads. External threads are cut with dies held in a die stock. Turn half a turn forward and a quarter back to break chips, keep the tap square, and lubricate.
Portable power tools used in fitting include the hand drill, angle grinder, jigsaw and bench grinder. Wear safety glasses, keep guards in place, unplug before changing bits or discs, check discs for cracks and their speed rating, and keep the tool rest of a bench grinder within about 3 mm of the wheel.
- Centre-punch, clamp, right speed, coolant, peck
- Drilling time t = depth/(f × N)
- Tap drill ≈ nominal − pitch; taps: taper, intermediate, bottoming
- Half-turn forward, quarter back
- Power tools: glasses, guards, unplug to change
Example: A 20 mm deep hole is drilled at 800 rpm and 0.1 mm/rev. Find the drilling time.
- t = depth/(f × N) = 20/(0.1 × 800).
- = 0.25 min = 15 s.
Answer: 15 s
Example: Find the tap-drill size for M10 × 1.5 and M12 × 1.75.
- Tap drill ≈ nominal − pitch.
- M10: 10 − 1.5 = 8.5 mm; M12: 12 − 1.75 = 10.25 mm (10.2 mm drill).
Answer: 8.5 mm and about 10.2 mm
Fitting is bench work that shapes and assembles parts by hand: marking, sawing, filing, drilling, tapping and checking with measuring tools. Common tools are the bench vice, hacksaw, files (flat, half-round, triangular), try square, scriber, centre punch, surface plate, vernier caliper and micrometer.
- Hacksaw blade teeth face forward; cut on the forward stroke.
- Files: rough, bastard, second cut, smooth, dead smooth by tooth spacing.
- Marking: surface plate, scriber, dot punch, try square, odd-leg caliper.
- Micrometer least count 0.01 mm; vernier 0.02 mm.
- Power tools: drill, angle grinder, bench grinder — use guards and goggles.
Key formulas
- Micrometer reading = MSR + (CSR × 0.01) mm
Practice questions
A hacksaw cuts on the
- backward stroke
- forward stroke
- both strokes
- neither
Show the answer
Answer: B. forward stroke Teeth face forward.
Least count of a common micrometer is
- 0.1 mm
- 0.01 mm
- 0.02 mm
- 1 mm
Show the answer
Answer: B. 0.01 mm Pitch 0.5 mm / 50 divisions.
A centre punch is used to
- cut metal
- mark hole centres
- measure angles
- file corners
Show the answer
Answer: B. mark hole centres Guides the drill.
The smoothest file grade listed is
- rough
- bastard
- second cut
- dead smooth
Show the answer
Answer: D. dead smooth Finest teeth.
Theory questions
Name four marking tools. (2 marks)
Show the model answer
Scriber, try square, centre/dot punch, surface plate, divider, odd-leg caliper.
Explain filing methods. (4 marks)
Show the model answer
Cross filing (stroke diagonally across the work for fast removal), straight filing (along the work), draw filing (file held crosswise and drawn along for a fine finish).
Describe the steps to make a square fitting job from a mild-steel plate. (8 marks)
Show the model answer
Check stock size; file reference edges square; apply marking medium; mark outlines with scriber and try square, punch witness marks; hacksaw close to the line; file to line checking squareness and dimensions with try square and vernier; drill and tap if required; deburr and finish.
Electrical and Electronics Practice
Topics: Electrical and electronics workshop practice.
Electrical safety, cables and wiring practice
Mains electricity (230 V, 50 Hz in India) can kill: currents of a few tens of milliamps through the body can stop the heart. Work only on isolated circuits: switch off, remove the fuse or lock the MCB, and test that the circuit is dead with a tester before touching. Use insulated tools, stand on a dry insulating surface, and never work alone on live equipment.
Indian colour codes for fixed wiring are red (phase), black (neutral) and green or green-yellow (earth); newer cables use brown, blue and green-yellow. Copper conductors are sized for current: typically 1.5 mm² for lighting and 2.5 mm² for 16 A power sockets, larger for heavy loads such as heaters and air conditioners. Switches must be in the phase wire so that the appliance is dead when switched off.
Common wiring practice exercises include one lamp controlled by one switch, two lamps in series and parallel, a lamp controlled from two places (staircase wiring with two two-way switches), fluorescent and LED tube connections, and a distribution board with MCBs. Check every circuit with a continuity tester and insulation tester before connecting to the supply.
- Isolate, lock out, test dead before touching
- Colours: red/brown phase, black/blue neutral, green(-yellow) earth
- 1.5 mm² lighting; 2.5 mm² 16 A sockets
- Switch in the phase wire
- Staircase wiring: two two-way switches
Example: A 2 kW heater runs on 230 V. Find its current and suggest the circuit rating.
- I = P/V = 2000/230 = 8.7 A.
- Use a 16 A socket circuit with 2.5 mm² copper and a 16 A MCB.
Answer: 8.7 A; 16 A circuit, 2.5 mm²
Example: Why must the switch be placed in the phase wire, not the neutral?
- With the switch in the neutral, the lamp holder stays connected to phase when off.
- Someone changing the bulb could touch a live part; in the phase, switching off isolates the lamp.
Answer: So that the appliance is dead when switched off
Protection: fuses, MCBs, RCCBs and earthing
Fuses and miniature circuit breakers (MCBs) protect cables and equipment from overload and short circuit by breaking the circuit when current exceeds their rating. An MCB has a thermal element for overloads and a magnetic trip for short circuits, and it can be reset. Rate the MCB to protect the cable, not the appliance.
A residual current circuit breaker (RCCB, or RCD) protects people. It compares the current going out in the phase with the current returning in the neutral; if they differ by more than its rating (30 mA for personal protection), current must be leaking through some other path, perhaps a person, and it trips within about 30 ms. An RCBO combines an MCB and an RCCB.
Earthing connects metal bodies of appliances to the ground through a low-resistance path (pipe or plate earth electrode), so that a fault current flows safely and operates the protective device instead of making the casing live. Earth electrodes need moist soil, and their resistance should be low (a few ohms); it is tested periodically with an earth tester.
- Fuse/MCB: overload and short circuit; protect the cable
- MCB: thermal + magnetic trip
- RCCB 30 mA: trips on phase–neutral imbalance
- RCBO = MCB + RCCB
- Earthing: low-resistance path; pipe or plate electrode
Example: A washing machine’s casing becomes live and a person touching it lets 35 mA flow to earth. What does each device do: the 16 A MCB and the 30 mA RCCB?
- 35 mA is far below 16 A, so the MCB does nothing.
- Phase and neutral now differ by 35 mA, above 30 mA, so the RCCB trips within about 30 ms.
Answer: Only the RCCB protects the person
Example: A 1.5 kW geyser runs 1 hour a day for 30 days at ₹6 per unit. Find the energy and cost.
- Energy = 1.5 kW × 1 h × 30 = 45 kWh (units).
- Cost = 45 × 6 = ₹270.
Answer: 45 kWh; ₹270
Electronics workshop practice
Electronics practice covers identifying and testing components (resistors by colour code, capacitors by markings and polarity, diodes and LEDs by their marked cathode, transistors by datasheet pinout), measuring with the multimeter and oscilloscope, and assembling circuits on breadboard and PCB.
Soldering is the core skill: clean the tip and tin it, heat the pad and lead together, feed solder to the joint, remove solder then iron, and inspect for a smooth, concave, shiny fillet. Avoid cold joints, bridges and excess heat that lifts pads. Use a stand, work in a ventilated place, and wash hands after handling leaded solder.
Typical exercises are a regulated power supply (transformer, bridge rectifier, filter capacitor and regulator), an LED flasher or 555 timer circuit, and a continuity tester. Test each stage with the multimeter and scope before moving on.
- Identify and test components; check polarity
- Solder: heat pad and lead; feed solder; inspect fillet
- Avoid cold joints, bridges, lifted pads
- Ventilate; wash hands after leaded solder
- Build and test stage by stage
Example: Decode a resistor banded red, red, brown, gold, and say how to check it.
- Red 2, red 2, brown ×10: 220 Ω ±5 %.
- Measure on the multimeter’s Ω range, out of circuit: it should read 209–231 Ω.
Answer: 220 Ω ±5 %; measure out of circuit
Example: A bridge rectifier output measures 0 V with the transformer working. Give two likely faults.
- A diode is reversed or open, or the output is shorted by a reversed electrolytic capacitor.
- Check diode orientation and the capacitor polarity, then test each diode on the diode range.
Answer: Wrong diode or capacitor orientation, or a failed diode
The electrical shop teaches safe wiring: identifying cables and accessories, making joints, wiring switches, sockets, lamps (including staircase two-way wiring), using a test lamp and multimeter, and soldering electronic components.
- Colour codes: phase red/brown, neutral black/blue, earth green/green-yellow.
- Two-way (staircase) wiring uses two SPDT switches to control one lamp from two places.
- Joints: Western Union, T-joint, married joint for conductors.
- Always isolate supply and test before work; use insulated tools.
- Soldering for electronic circuits: iron, flux-core solder, desoldering pump.
Practice questions
Staircase wiring needs
- one SPST switch
- two two-way switches
- a dimmer
- a fuse only
Show the answer
Answer: B. two two-way switches Control from two places.
Earth wire colour is
- red
- black
- green/green-yellow
- blue
Show the answer
Answer: C. green/green-yellow Standard colour.
Before working on a circuit you must
- switch off and test it is dead
- wet your hands
- remove the earth
- increase the fuse rating
Show the answer
Answer: A. switch off and test it is dead Isolate and verify.
A Western Union joint is used for
- joining two conductors end to end
- soldering ICs
- earthing
- fuses
Show the answer
Answer: A. joining two conductors end to end Straight joint.
Theory questions
What is two-way wiring? (2 marks)
Show the model answer
A circuit where one lamp is controlled independently from two locations using two SPDT switches, as in staircases.
List safety precautions in the electrical workshop. (4 marks)
Show the model answer
Isolate supply, use insulated tools, wear rubber footwear, never work with wet hands, use correct fuse/MCB rating, earth metal parts, keep first-aid and fire extinguisher ready, do not overload sockets.
Draw and explain staircase wiring and the steps to test it. (8 marks)
Show the model answer
Phase to common of switch 1, travellers between switches, common of switch 2 to lamp, lamp to neutral; any toggle changes state. Test continuity with multimeter before energising, check with test lamp, then verify all four switch combinations.
Carpentry
Topics: Carpentry.
Timber and carpentry tools
Timber is classed as softwood (from conifers: pine, deodar, fir; light, easy to work) or hardwood (from broad-leaved trees: teak, sal, sheesham; strong, durable). In Assam, bamboo is also an important building and craft material. Freshly felled timber contains much water and must be seasoned (dried, by air or kiln) to a moisture content of about 10–15 % for indoor use; otherwise it shrinks, warps and splits.
Moisture content (dry basis) = (wet mass − oven-dry mass)/oven-dry mass × 100 %. Timber also has defects to check before use: knots, shakes (cracks), warping, decay and insect attack. Engineered boards (plywood, block board, MDF, particle board) give large stable sheets.
Carpentry tools include marking and measuring tools (steel rule, try square, marking gauge, mortise gauge, bevel), saws (rip saw along the grain, cross-cut saw across it, tenon saw for fine joints, coping saw for curves), planes (jack, smoothing), chisels (firmer, bevel-edge, mortise) with a mallet, and drilling and boring tools.
- Softwood vs hardwood; bamboo
- Seasoning to about 10–15 % moisture
- MC = (wet − dry)/dry × 100 %
- Defects: knots, shakes, warping, decay
- Saws: rip, cross-cut, tenon, coping; planes; chisels with mallet
Example: A timber sample weighs 600 g wet and 500 g oven-dry. Find its moisture content. Is it ready for indoor furniture?
- MC = (600 − 500)/500 × 100 = 20 %.
- Indoor furniture needs about 10–15 %, so it needs further seasoning.
Answer: 20 %; not yet
Example: A teak plank is 2 m × 200 mm × 25 mm. Find its volume and cost at ₹60 000 per m³.
- V = 2 × 0.2 × 0.025 = 0.01 m³.
- Cost = 0.01 × 60 000 = ₹600.
Answer: 0.01 m³; ₹600
Carpentry joints
Joints connect pieces of timber. Lap joints (half lap, cross lap) overlap halved pieces for frames. Mortise and tenon joints, a tongue (tenon) fitted into a slot (mortise), are strong and used for doors, tables and chairs. Dovetail joints, with flared interlocking pins and tails, resist pulling apart and are used for drawers and boxes. Bridle joints, dowel joints and butt joints with screws or nails are also common.
Proportions follow rules of thumb: the mortise width is usually about one-third of the stock thickness, and the tenon length about three-quarters to the full width of the mating piece. Mark with gauges from the face side and face edge, cut on the waste side of the line, and test-fit before gluing.
Joints are glued (PVA or synthetic resin adhesive) and clamped until set. Good joints fit snugly by hand without forcing, with no gaps showing.
- Lap, mortise and tenon, dovetail, bridle, dowel, butt
- Mortise width ≈ one-third of thickness
- Mark from face side and face edge
- Cut on the waste side of the line
- Glue and clamp; snug hand fit
Example: Choose a joint for: (a) a drawer front; (b) a table leg to rail; (c) a simple window frame corner.
- (a) Dovetail, which resists pulling.
- (b) Mortise and tenon; (c) bridle or half-lap joint.
Answer: Dovetail; mortise and tenon; bridle/lap
Example: A rail is 45 mm thick. Suggest the mortise width.
- Mortise ≈ one-third of the thickness.
- 45/3 = 15 mm; use the nearest chisel size.
Answer: About 15 mm
Wood turning and safety
A wood lathe spins the work between centres (spindle turning, for legs and handles) or on a faceplate (bowls and plates) while hand-held tools rest on the tool rest. Gouges rough and shape, skew chisels smooth cylinders, and parting tools cut grooves and separate the work.
Speed must suit the diameter: surface speed rises with diameter, so large blanks turn slowly and small spindles fast. Surface speed = πDN; keeping it to a few hundred metres per minute is typical. Start at the lowest speed for an unbalanced blank.
Safety: wear a face shield, tie back hair and sleeves, check the blank for cracks and loose knots, keep the tool rest close and stop the lathe to adjust it, and spin the work by hand before switching on.
- Between centres or faceplate
- Gouge, skew chisel, parting tool
- Surface speed = πDN; large work turns slow
- Start slow for unbalanced blanks
- Face shield; adjust the rest only when stopped
Example: A 100 mm bowl turns at 1000 rpm. Find its rim speed.
- v = π × 0.1 m × 1000 rpm.
- = 314 m/min.
Answer: About 314 m/min
Example: What speed keeps a 300 mm blank’s rim at 300 m/min?
- N = v/(πD) = 300/(π × 0.3).
- N ≈ 318 rpm; start lower if it is unbalanced.
Answer: About 320 rpm
Carpentry shapes and joins wood. Tools include the marking gauge, try square, rip saw (along the grain), cross-cut saw, tenon saw, jack plane, chisels, mallet and brace and bit. Common joints are lap, mortise-and-tenon, dovetail and bridle joints.
- Rip saw cuts along the grain; cross-cut saw across it.
- Jack plane levels and smooths surfaces.
- Mortise-and-tenon: strong frame joint (doors, windows).
- Dovetail: interlocking drawer joint resisting pull-out.
- Seasoning reduces moisture so wood does not warp or crack.
Practice questions
A rip saw cuts
- across the grain
- along the grain
- metal
- plastic
Show the answer
Answer: B. along the grain Along the fibres.
A dovetail joint is common in
- drawers
- roof trusses
- pipes
- PCBs
Show the answer
Answer: A. drawers Resists pull-out.
Seasoning of timber removes
- colour
- moisture
- grain
- knots
Show the answer
Answer: B. moisture Prevents warping.
A mallet is used with
- chisels
- saws
- planes
- gauges
Show the answer
Answer: A. chisels Wooden hammer.
Theory questions
Name three carpentry joints. (2 marks)
Show the model answer
Lap, mortise-and-tenon, dovetail, bridle, T-halving joints.
Why is timber seasoned? (3 marks)
Show the model answer
To reduce moisture to equilibrium level so it does not shrink, warp, crack or decay, and becomes stronger and easier to work and finish.
Describe the steps of making a mortise-and-tenon joint. (8 marks)
Show the model answer
Plane stock to size; mark tenon thickness (≈1/3 of stock) with mortise gauge; mark shoulders with try square; saw cheeks and shoulders with tenon saw; mark mortise; chop with mortise chisel and mallet; trial fit; glue and clamp.
Plastic Moulding and Glass Cutting
Topics: Plastic moulding and glass cutting.
Plastics and injection moulding
Plastics are thermoplastics, which soften on heating and can be remelted (polyethylene, polypropylene, PVC, polystyrene, ABS, nylon, PET), or thermosets, which set permanently when cured (bakelite, epoxy, melamine). Thermoplastics are shaped by melting and moulding; thermosets by curing in a heated mould.
Injection moulding is the main process for plastic parts: pellets are melted by a rotating screw in a heated barrel, injected under high pressure into a closed steel mould, held under pressure while they cool, and ejected. Cycle times are seconds, so millions of identical parts (caps, housings, buckets, toys) can be made cheaply, but the mould is expensive.
The clamping force must resist the injection pressure acting over the projected area of the part: F = A × p. Plastics shrink as they cool (roughly 0.5–2 %), so moulds are made slightly oversize. Good designs keep wall thickness uniform, add draft angles for easy ejection, and use ribs instead of thick sections to avoid sink marks.
- Thermoplastics (remeltable) vs thermosets (cured)
- Melt, inject, hold, cool, eject
- Clamp force = projected area × cavity pressure
- Shrinkage 0.5–2 %: oversize mould
- Uniform walls, draft angles, ribs
Example: A part has a projected area of 100 cm² and cavity pressure of 40 MPa. Find the clamping force.
- F = A × p = 0.01 m² × 40 × 10⁶ Pa = 4 × 10⁵ N.
- = 400 kN, about 40 tonnes-force.
Answer: About 400 kN (40 t)
Example: A part must be 100 mm long after 2 % shrinkage. What length should the mould cavity be?
- Final = cavity × (1 − 0.02).
- Cavity = 100/0.98 = 102.0 mm.
Answer: About 102 mm
Other plastic processes
Extrusion pushes molten plastic continuously through a shaped die, making pipes, rods, profiles, sheets and, with a blown bubble, film for bags. Blow moulding inflates a hot tube (parison) or preform inside a mould to make hollow articles such as bottles and jerrycans.
Compression moulding presses a charge of thermoset (or rubber) in a heated mould until it cures: electrical switch plates, sockets and melamine tableware. Thermoforming heats a plastic sheet and draws it over a mould by vacuum or pressure: food trays, cups and packaging. Rotational moulding spins powder in a heated mould to coat its walls, making large hollow parts such as the black water tanks on Indian rooftops.
Plastics bring environmental duties: choose recyclable materials, mark resin codes, avoid unnecessary single-use items, and design for reuse and recycling. India’s rules restrict many single-use plastics.
- Extrusion: continuous profiles, pipes, film
- Blow moulding: hollow bottles and cans
- Compression moulding: thermosets
- Thermoforming: sheet over a mould
- Rotational moulding: large tanks; recycle and mark resin codes
Example: Choose a process for: (a) a PVC water pipe; (b) a PET drink bottle; (c) a bakelite switch plate; (d) a 1000 L rooftop tank.
- (a) Extrusion; (b) blow moulding.
- (c) Compression moulding; (d) rotational moulding.
Answer: Extrusion, blow, compression, rotational moulding
Example: Why can a bakelite switch plate not be recycled by melting like a PET bottle?
- Bakelite is a thermoset: its chains are cross-linked when cured.
- Heating chars it instead of melting it; PET is a thermoplastic and can be remelted.
Answer: Thermosets do not remelt
Glass cutting
Flat glass is cut not by sawing but by scoring and breaking. A glass cutter’s hardened steel or carbide wheel draws a fine, continuous score that weakens the surface along the line; bending the glass so the score is on the outside (in tension) makes it crack cleanly along it.
Score only once, in one smooth stroke with steady pressure, holding the cutter upright; going over a score again damages the cutter and gives a ragged break. Break promptly, by snapping over a straight edge, tapping beneath the score, or with running pliers. Thick or curved cuts need more skill; toughened glass cannot be cut after tempering, as it shatters.
Safety: wear safety glasses and cut-resistant gloves, carry sheets vertically, sweep up fragments with a brush (not hands), and smooth sharp edges with an abrasive stone. Glass weighs about 2.5 kg per square metre per millimetre of thickness.
- Score and snap, not saw
- One smooth score with steady pressure; never re-score
- Snap promptly over an edge or with running pliers
- Toughened glass cannot be cut
- Glasses and gloves; ≈ 2.5 kg/m² per mm
Example: Find the mass of a 1 m² sheet of 4 mm glass.
- Glass density about 2500 kg/m³.
- Mass = 1 × 0.004 × 2500 = 10 kg.
Answer: 10 kg
Example: A student scores a line, finds a gap, and scores over it again. The break is ragged. Why?
- A second pass crushes the first score and chips the surface.
- Score once in one continuous stroke, then break promptly.
Answer: Re-scoring spoils the score; score once
Thermoplastics are shaped by heating: injection moulding forces molten plastic into a closed mould (bottle caps, housings), blow moulding inflates a parison (bottles), extrusion pushes it through a die (pipes), thermoforming draws heated sheets over a mould. Glass is cut by scoring a line with a diamond or wheel cutter and snapping along it.
- Thermoplastics re-melt (PE, PP, PVC, ABS); thermosets cure permanently (Bakelite, epoxy).
- Injection moulding cycle: clamp, inject, hold, cool, eject.
- Blow moulding for hollow objects.
- Glass cutting: clean surface, one continuous score, tap/snap along the line, wear gloves.
Practice questions
Plastic bottles are made by
- injection moulding
- blow moulding
- forging
- turning
Show the answer
Answer: B. blow moulding Inflated parison.
Bakelite is a
- thermoplastic
- thermoset
- metal
- glass
Show the answer
Answer: B. thermoset Cannot be re-melted.
Glass is cut by
- sawing
- scoring and snapping
- melting
- drilling only
Show the answer
Answer: B. scoring and snapping Controlled crack.
Pipes are made by
- extrusion
- casting
- blow moulding
- stamping
Show the answer
Answer: A. extrusion Continuous profile.
Theory questions
Differentiate thermoplastics and thermosets. (2 marks)
Show the model answer
Thermoplastics soften on heating and can be remoulded; thermosets undergo cross-linking and cannot be re-melted.
Explain injection moulding. (4 marks)
Show the model answer
Granules heated in barrel by heaters and screw shear; screw injects melt into closed mould; pressure held; part cools; mould opens; ejector pins push part out; cycle repeats.
Describe plastic moulding processes and glass cutting technique. (8 marks)
Show the model answer
Injection, blow, extrusion, compression and thermoforming with examples; glass cutting procedure and safety.
Metal Casting
Topics: Metal casting.
The sand-casting process
Sand casting makes a mould from a pattern packed in moulding sand (silica sand with clay binder and water, called green sand) inside a two-part box: the cope (top) and drag (bottom). The pattern is removed, cores are placed for hollow sections, and channels are cut: the pouring basin and sprue lead metal down, runners carry it across, and gates feed it into the cavity.
Molten metal from a furnace (cupola for cast iron, crucible or induction furnace for others) is poured steadily into the mould, solidifies, and the casting is knocked out, the gates and risers cut off, and the surface fettled (cleaned). Casting yield = casting mass/mass poured is often 50–80 %, since gates and risers are remelted.
Moulding sand needs permeability (to let gases escape), strength, refractoriness (to withstand heat), collapsibility (to let the casting shrink and to break out easily), and flowability. Its properties are tested in the foundry lab.
- Pattern, cope and drag, cores
- Basin, sprue, runner, gates; risers
- Pour, solidify, knock out, fettle
- Yield = casting mass/mass poured
- Sand: permeability, strength, refractoriness, collapsibility
Example: A cast-iron part has a volume of 500 cm³ (density 7.2 g/cm³) and casting yield is 70 %. How much metal must be poured?
- Casting mass = 500 × 7.2 = 3600 g = 3.6 kg.
- Pour = 3.6/0.70 = 5.14 kg.
Answer: About 5.1 kg
Example: Why is clay and water added to the silica sand, and why must the sand be permeable?
- Clay and water bond the grains so the mould holds its shape (strength).
- Steam and gases form as hot metal meets the sand; permeability lets them escape, avoiding blowholes.
Answer: For strength, and to vent gases
Patterns and allowances
A pattern is a replica of the casting used to form the mould cavity, made of wood, metal, plastic or wax. Types include single-piece, split (two-piece) patterns for shapes that cannot be drawn from one half, match-plate patterns for production, and loose-piece patterns for projections.
A pattern is not the same size as the part, because of allowances. Shrinkage (contraction) allowance makes it larger, since metal contracts as it cools (about 10 mm/m for grey cast iron, about 20 mm/m for steel, 13 mm/m for aluminium). Machining allowance adds metal on surfaces to be machined. Draft (taper) allowance of about 1–3° on vertical faces lets the pattern be withdrawn without damaging the mould. Distortion and shake (rapping) allowances are smaller corrections.
Patterns are colour-coded in many shops (for example, surfaces to be left unmachined, machined and core prints in different colours), and core prints on the pattern form seats that locate the cores.
- Single-piece, split, match-plate, loose-piece patterns
- Shrinkage: CI ≈ 10, steel ≈ 20, Al ≈ 13 mm/m
- Machining allowance on machined faces
- Draft 1–3° on vertical faces
- Core prints locate cores
Example: A cast-iron part is 300 mm long and both ends are machined, 3 mm each. With 10 mm/m shrinkage, find the pattern length.
- Rough casting length = 300 + 3 + 3 = 306 mm.
- Add shrinkage: 306 × 1.01 = 309.1 mm.
Answer: About 309 mm
Example: Why does a pattern need draft, and roughly how much?
- Vertical faces would drag sand away when the pattern is lifted.
- A taper of about 1–3° lets it come out cleanly.
Answer: For clean withdrawal; about 1–3°
Gating, risers, solidification and defects
Gating should fill the mould quickly but without turbulence, which entrains air and erodes sand. Risers are reservoirs of molten metal that feed the casting as it shrinks during solidification; to work, a riser must freeze after the casting section it feeds.
Chvorinov’s rule estimates solidification time: t = B(V/A)², where V/A, the volume-to-surface-area ratio (the casting modulus), measures how slowly a shape loses heat and B is a mould constant. Thick, compact shapes freeze slowly; thin plates quickly. Risers are therefore made with a larger modulus than the section they feed, usually as cylinders.
Defects include blowholes and gas porosity, shrinkage cavities, cold shuts and misruns (metal too cold or poured too slowly), hot tears (cracking as the casting shrinks against a hard mould), sand inclusions and mismatched cope and drag. Inspection uses visual checks, dimensional checks, and non-destructive tests such as dye penetrant and radiography.
- Quick, smooth filling; avoid turbulence
- Risers must freeze last
- Chvorinov: t = B(V/A)²
- Defects: blowholes, shrinkage, cold shut, misrun, hot tear, inclusions
- Inspect visually, dimensionally, NDT
Example: Compare the solidification times of a 100 mm cube and a 200 × 200 × 20 mm plate in the same mould.
- Cube: V/A = 100³/(6 × 100²) = 16.7 mm. Plate: V = 800 000 mm³, A = 2 × 200² + 4 × 200 × 20 = 96 000 mm², V/A = 8.33 mm.
- Time ratio = (16.7/8.33)² = 4.
Answer: The cube takes about 4 times as long
Example: A casting has a smooth-walled round hole inside a thick section, and a jagged cavity at its centre. Identify each defect.
- A smooth round hole is a blowhole (gas).
- A jagged cavity in a thick section is shrinkage, from inadequate feeding.
Answer: Blowhole; shrinkage cavity
Sand casting uses a pattern to make a cavity in moulding sand held in a flask (cope above, drag below). Molten metal is poured through the sprue, runners and gates; risers feed shrinkage. After solidification the casting is knocked out, fettled (cleaned) and inspected for defects such as blowholes, shrinkage, cold shuts and misruns.
- Pattern allowances: shrinkage, machining, draft, distortion, shake.
- Moulding sand: silica + clay binder + moisture; properties: permeability, strength, refractoriness.
- Gating system: pouring basin, sprue, runner, ingate; riser feeds shrinkage.
- Cores make internal cavities.
- Defects: blowholes (gas), shrinkage cavities, cold shut, misrun, hot tears.
Practice questions
The top half of a moulding flask is the
- drag
- cope
- core
- riser
Show the answer
Answer: B. cope Drag is the bottom.
A riser is provided to
- make holes
- feed shrinkage
- cool the mould
- hold the pattern
Show the answer
Answer: B. feed shrinkage Reservoir of molten metal.
Draft allowance helps
- strength
- easy withdrawal of the pattern
- colour
- cooling
Show the answer
Answer: B. easy withdrawal of the pattern Tapered sides.
Blowholes are caused by
- trapped gases
- too much metal
- cold pattern
- paint
Show the answer
Answer: A. trapped gases Low permeability or moisture.
Theory questions
Name pattern allowances. (2 marks)
Show the model answer
Shrinkage, machining (finish), draft, distortion and shake (rapping) allowances.
What properties should moulding sand have? (4 marks)
Show the model answer
Permeability, green and dry strength, refractoriness, cohesiveness, adhesiveness, collapsibility, flowability.
Describe the sand casting process with a neat sketch and list common defects. (8 marks)
Show the model answer
Pattern making, moulding in cope and drag with gating and riser, core setting, closing, pouring, solidification, shake-out, fettling, inspection; defects as listed with causes and remedies.
Welding and Brazing
Topics: Arc welding, gas welding, brazing.
Arc welding
Welding joins metals by melting the edges together, usually with added filler, so that they fuse into one piece when they solidify. In shielded metal arc welding (SMAW, “stick” welding) an electric arc between a flux-coated consumable electrode and the work melts both; the flux coating produces shielding gas and slag that protect the hot metal from air. Transformers (AC) or rectifiers and inverters (DC) supply the current.
Other arc processes include MIG/MAG (gas metal arc, with a wire fed continuously and shielding gas), TIG (gas tungsten arc, with a non-consumable tungsten electrode, for thin and high-quality welds), submerged arc and spot (resistance) welding. Heat input per unit length, about ηVI/v (efficiency × voltage × current ÷ travel speed), affects penetration, distortion and properties.
Edges are prepared by joint type: butt, lap, T, corner and edge joints, with V or U grooves on thick plates. The welder strikes the arc, keeps a short steady arc length, moves at an even speed and angle, and chips off slag between runs.
- SMAW: flux-coated electrode; shielding gas and slag
- MIG/MAG, TIG, submerged arc, spot
- Heat input ≈ ηVI/v
- Joints: butt, lap, T, corner, edge; V/U grooves
- Short steady arc; even speed; remove slag
Example: An arc runs at 25 V and 150 A with a travel speed of 5 mm/s and efficiency 0.8. Find the heat input per mm.
- VI/v = 25 × 150/5 = 750 J/mm.
- With efficiency 0.8: 600 J/mm into the work.
Answer: 600 J/mm (750 gross)
Example: Which process suits: (a) thin stainless-steel sheet with neat welds; (b) a farm gate of mild-steel angles in the field; (c) car-body panels in a factory?
- (a) TIG; (b) stick (SMAW), portable and tolerant of wind.
- (c) Resistance spot welding.
Answer: TIG; stick; spot welding
Gas welding and cutting
Oxy-acetylene welding burns acetylene with oxygen in a torch, giving a flame of about 3100–3200 °C at the tip of the inner cone, hot enough to melt steel; a filler rod is added by hand. It needs no electricity, which makes it portable, and the same equipment can braze, heat and cut.
The flame is adjusted by the gas ratio: a neutral flame (equal volumes) for most steels; a carburising flame (excess acetylene) for high-carbon steel and hard-facing; and an oxidising flame (excess oxygen) for brass and bronze. Oxy-fuel cutting preheats steel to its ignition temperature and then blows a jet of pure oxygen that burns the iron and blows the oxide away.
Cylinders in India are colour-coded: oxygen black, acetylene maroon. Keep them upright and chained, use regulators and flashback arrestors, check hoses for leaks with soapy water, open the acetylene valve only partly, light acetylene first and close it first, and wear tinted goggles.
- Oxy-acetylene ≈ 3100–3200 °C; portable
- Neutral, carburising, oxidising flames
- Cutting: preheat + oxygen jet
- Cylinders: oxygen black, acetylene maroon
- Upright, chained; regulators, flashback arrestors; goggles
Example: Which flame would you use to weld: (a) mild steel; (b) brass; (c) a hard-facing layer?
- (a) Neutral flame.
- (b) Oxidising flame, which forms a protective oxide that limits zinc fuming; (c) carburising flame.
Answer: Neutral; oxidising; carburising
Example: Why can oxy-fuel cutting cut mild steel but not stainless steel or aluminium easily?
- It depends on the metal burning in oxygen with an oxide that melts below the metal and blows away.
- Stainless and aluminium form refractory oxides (Cr₂O₃, Al₂O₃) that melt above the metal; plasma or laser cutting is used instead.
Answer: Their oxides are refractory; use plasma or laser
Brazing, soldering, weld quality and safety
Brazing joins metals with a filler that melts above 450 °C but below the base metals (brass or silver alloys), drawn into a close-fitting joint by capillary action; the base metals do not melt. It joins dissimilar metals (copper to steel), thin parts and pipes, with less distortion than welding. Soldering is similar but below 450 °C (tin-based solders) and weaker, used for electronics and plumbing. Fluxes clean the surfaces in both.
Weld defects include porosity (gas), slag inclusions, lack of fusion or penetration, undercut (a groove at the weld edge), cracks, and distortion. They are found by visual inspection, dye penetrant, magnetic particle, ultrasonic and radiographic testing. Pre-heating, correct current and speed, clean joints and proper sequence reduce them.
Welding is hazardous: ultraviolet and infrared radiation (use the correct shade of helmet filter and screens to protect others), fumes (ventilate), electric shock (dry gloves, insulated holders, earthed work), burns and fire (remove flammables, keep an extinguisher), and hot metal (use tongs, mark hot work). Never weld containers that held fuel without proper cleaning.
- Brazing > 450 °C, base metal not melted; capillary
- Soldering < 450 °C
- Defects: porosity, slag, lack of fusion, undercut, cracks
- NDT: dye penetrant, magnetic particle, ultrasonic, X-ray
- Shield eyes, ventilate, avoid shock, prevent fire
Example: Choose a joining process for: (a) a copper pipe to a brass fitting; (b) wires on a circuit board; (c) two thick steel plates in a structure.
- (a) Brazing (or soft soldering for low pressure).
- (b) Soldering; (c) arc welding.
Answer: Brazing, soldering, welding
Example: A weld shows a groove melted into the base metal along its edge. Name the defect and a likely cause.
- A groove at the weld toe is undercut.
- Typical causes: current too high, travel too fast, or wrong electrode angle.
Answer: Undercut; reduce current or correct the angle and speed
Welding joins metals by melting them locally, with or without filler. In shielded metal arc welding an electric arc (≈ 6000 °C) between a flux-coated electrode and the work melts both; the flux forms gas and slag that protect the weld. Oxy-acetylene gas welding uses a flame (≈ 3200 °C) whose type — neutral, oxidising or carburising — is set by the gas ratio. Brazing joins with a filler that melts above 450 °C but below the base metal’s melting point, without melting the parent metal; soldering is the same below 450 °C.
- Arc welding needs a transformer/rectifier, electrode holder, earth clamp, PPE (shield with dark filter glass, gloves, apron).
- Neutral flame (1 : 1 O₂ : C₂H₂) for most steels; oxidising for brass; carburising for high-carbon steel.
- Joints: butt, lap, T, corner, edge.
- Defects: porosity, slag inclusion, undercut, lack of fusion, cracks.
- Brazing: brass/silver filler, capillary action, flux; soldering: tin–lead or lead-free alloys.
Key formulas
- Heat input ≈ VI/v (arc)
Practice questions
A neutral oxy-acetylene flame has oxygen to acetylene ratio of about
- 1 : 1
- 2 : 1
- 1 : 2
- 3 : 1
Show the answer
Answer: A. 1 : 1 Equal volumes.
Brazing filler melts
- below 450 °C
- above 450 °C but below the base metal
- above the base metal
- at room temperature
Show the answer
Answer: B. above 450 °C but below the base metal Soldering is below 450 °C.
The flux coating on an arc electrode
- shields the weld from air
- cools the work
- increases current
- is decorative
Show the answer
Answer: A. shields the weld from air Gas and slag shielding.
Eyes are protected during arc welding by
- sunglasses
- a helmet with dark filter glass
- nothing
- a cap
Show the answer
Answer: B. a helmet with dark filter glass UV and IR radiation.
Theory questions
Differentiate welding, brazing and soldering. (3 marks)
Show the model answer
Welding melts parent metal (with/without filler); brazing uses filler above 450 °C without melting parent metal; soldering uses filler below 450 °C; strength decreases in that order.
Explain the three types of oxy-acetylene flames and their uses. (4 marks)
Show the model answer
Neutral (equal gases, clear inner cone; most metals), oxidising (excess O₂, short pointed cone; brass, bronze), carburising/reducing (excess C₂H₂, feather; high-carbon steel, hard facing).
Describe shielded metal arc welding with a sketch, its equipment, safety and defects. (8 marks)
Show the model answer
Power source (AC transformer or DC rectifier), cables, electrode holder, earth clamp, coated electrodes; arc struck by touch and lift, maintained at ~3 mm, travel along joint; flux shielding; chip slag. Safety: helmet with filter, gloves, apron, ventilation, dry area. Defects: porosity, slag inclusions, undercut, incomplete fusion, cracks, spatter.