IITIAN1997 STUDIO

Physics

BS101 · 35 questions with answers

Open this subject studio →

Quantum Mechanics

Topics: Wave nature of particles, uncertainty principle, wave function and wave packets, time-dependent and time-independent Schrödinger equation, particle in a one-dimensional box.

Wave nature of particles

Light shows both faces: interference and diffraction need waves, while the photoelectric effect needs particles (photons of energy hν). In 1924 de Broglie proposed the reverse: every moving particle has a wave of wavelength λ = h/p, where p is its momentum. The wave is not a ripple in a medium but governs where the particle is likely to be found.

Davisson and Germer confirmed this in 1927 by scattering 54 eV electrons from a nickel crystal and finding a diffraction peak exactly where Bragg’s law predicted for λ = h/p. Electron microscopes exploit the short wavelength of fast electrons to resolve detail far below the limit of light.

For an electron accelerated from rest through V volts, p = √(2meV), so λ = h/√(2meV) ≈ 1.227/√V nm. For everyday objects the wavelength is absurdly small, which is why wave behaviour is never noticed for a cricket ball. The wave of a particle travels with a phase velocity greater than c, but the energy and the particle move with the group velocity, which equals the particle’s speed.

  • λ = h/p = h/(mv)
  • Electron through V volts: λ = h/√(2meV) ≈ 1.227/√V nm
  • Davisson–Germer: electron diffraction from nickel
  • Group velocity = particle velocity
  • Large objects: λ too small to notice

Example: Find the de Broglie wavelength of an electron accelerated through 100 V.

  1. p = √(2meV) = √(2 × 9.109 × 10⁻³¹ × 1.602 × 10⁻¹⁹ × 100) = 5.40 × 10⁻²⁴ kg·m/s.
  2. λ = h/p = 6.626 × 10⁻³⁴/5.40 × 10⁻²⁴.
  3. λ = 1.227 × 10⁻¹⁰ m, the same as 1.227/√100 nm.

Answer: 0.123 nm

Example: Find the de Broglie wavelength of a 0.1 kg ball moving at 10 m/s, and comment.

  1. p = 0.1 × 10 = 1 kg·m/s.
  2. λ = 6.626 × 10⁻³⁴/1 = 6.63 × 10⁻³⁴ m.
  3. This is about 10¹⁹ times smaller than a proton, so no diffraction can ever be seen.

Answer: 6.63 × 10⁻³⁴ m: undetectable

Example: What wavelength did the Davisson–Germer electrons of 54 eV have?

  1. λ = 1.227/√54 nm.
  2. λ = 1.227/7.35 = 0.167 nm.

Answer: 0.167 nm, comparable with atomic spacings

Uncertainty principle and wave packets

A single wave of one wavelength stretches forever, so a particle that is somewhere in particular must be described by a wave packet: a sum of many waves with a spread of wavelengths that reinforce in one region and cancel elsewhere. The narrower the packet in space, the wider the spread of wavelengths, and hence of momenta, needed to build it.

Heisenberg’s uncertainty principle states this precisely: Δx·Δp ≥ ħ/2, where ħ = h/2π. It is not a defect of instruments but a property of waves. A similar relation, ΔE·Δt ≥ ħ/2, links the energy spread of a state to its lifetime, which is why short-lived excited states give spectral lines with a natural width.

The principle explains why electrons cannot sit inside the nucleus (confinement to 10⁻¹⁴ m would need momenta far beyond observed beta-electron energies), why atoms have a minimum size, and why even at absolute zero oscillators keep a zero-point energy.

  • Δx·Δp ≥ ħ/2 = h/(4π)
  • ΔE·Δt ≥ ħ/2
  • Narrow packet ⇔ wide momentum spread
  • Natural line width from finite lifetime
  • No electrons in the nucleus; zero-point energy

Example: An electron is confined to 1 Å (10⁻¹⁰ m). Find the least uncertainty in its momentum and velocity.

  1. Δp ≥ h/(4πΔx) = 6.626 × 10⁻³⁴/(4π × 10⁻¹⁰) = 5.27 × 10⁻²⁵ kg·m/s.
  2. Δv = Δp/m = 5.27 × 10⁻²⁵/9.109 × 10⁻³¹.
  3. Δv ≈ 5.79 × 10⁵ m/s.

Answer: Δp ≈ 5.3 × 10⁻²⁵ kg·m/s, Δv ≈ 5.8 × 10⁵ m/s

Example: An excited atomic state lives 10⁻⁸ s. Estimate the least spread in its energy.

  1. ΔE ≥ h/(4πΔt) = 6.626 × 10⁻³⁴/(4π × 10⁻⁸) = 5.27 × 10⁻²⁷ J.
  2. In eV: 5.27 × 10⁻²⁷/1.602 × 10⁻¹⁹ = 3.3 × 10⁻⁸ eV.

Answer: About 3.3 × 10⁻⁸ eV

Wave function and the Schrödinger equation

The state of a particle is described by a wave function ψ(x, t). Born’s interpretation gives it meaning: |ψ|² dx is the probability of finding the particle between x and x + dx. Because the particle must be somewhere, ψ is normalised, ∫|ψ|² dx = 1. An acceptable ψ must be single-valued, finite and continuous, with a continuous slope wherever the potential is finite.

The time-dependent Schrödinger equation, iħ ∂ψ/∂t = −(ħ²/2m) ∂²ψ/∂x² + Vψ, plays the role of Newton’s law. When V does not depend on time, separating ψ = φ(x) e^(−iEt/ħ) gives the time-independent equation −(ħ²/2m) d²φ/dx² + Vφ = Eφ, whose acceptable solutions exist only for certain energies E: this is how quantisation arises.

Measurable quantities are found from expectation values, for example ⟨x⟩ = ∫ψ* x ψ dx. Momentum is represented by the operator −iħ d/dx and energy by iħ ∂/∂t. For a stationary state |ψ|² does not change with time, which is why bound states such as atomic orbitals are stable.

  • |ψ|² dx = probability; ∫|ψ|² dx = 1
  • ψ single-valued, finite, continuous
  • Time-dependent: iħ ∂ψ/∂t = −(ħ²/2m)∂²ψ/∂x² + Vψ
  • Time-independent: −(ħ²/2m)φ″ + Vφ = Eφ
  • Expectation value ⟨x⟩ = ∫ψ* x ψ dx

Example: Normalise ψ = A sin(πx/L) for 0 ≤ x ≤ L (zero outside).

  1. ∫₀ᴸ A² sin²(πx/L) dx = A² × L/2 (the average of sin² over whole half-waves is ½).
  2. Set A²L/2 = 1.
  3. A = √(2/L).

Answer: A = √(2/L)

Example: For the ground state of a box of length L, find the probability of finding the particle in the middle third.

  1. P = (2/L)∫ sin²(πx/L) dx from L/3 to 2L/3.
  2. Using sin² = (1 − cos 2θ)/2: P = 1/3 − (1/2π)[sin(4π/3) − sin(2π/3)].
  3. P = 1/3 + √3/(2π) = 0.333 + 0.276.

Answer: P ≈ 0.609, much more than one third

Particle in a one-dimensional box

Take V = 0 for 0 < x < L and V infinite outside. Inside, the time-independent equation reads φ″ + k²φ = 0 with k² = 2mE/ħ², so φ = A sin kx + B cos kx. The walls force φ(0) = 0, giving B = 0, and φ(L) = 0, giving kL = nπ with n = 1, 2, 3 … . The wave functions are standing waves φₙ = √(2/L) sin(nπx/L), with n − 1 nodes inside.

The allowed energies are Eₙ = n²h²/(8mL²). The lowest energy is not zero: a confined particle always moves (zero-point energy), as the uncertainty principle demands. The levels spread apart as n², and squeezing the box raises them all as 1/L², which is the physics behind quantum dots whose colour depends on their size.

A transition from level n₂ down to n₁ emits a photon of energy (n₂² − n₁²)h²/(8mL²). The model is crude but useful: it estimates the colours of conjugated dye molecules (π electrons in a chain), the energies of electrons in thin semiconductor layers, and the size of quantum effects.

  • φₙ = √(2/L) sin(nπx/L), n = 1, 2, 3 …
  • Eₙ = n²h²/(8mL²)
  • E₁ ≠ 0: zero-point energy
  • Levels grow as n²; shrink the box and they rise as 1/L²
  • Photon energy (n₂² − n₁²)h²/(8mL²)

Example: An electron is in a box of width 1 Å. Find E₁ and E₂ in eV.

  1. E₁ = h²/(8mL²) = (6.626 × 10⁻³⁴)²/(8 × 9.109 × 10⁻³¹ × 10⁻²⁰) = 6.02 × 10⁻¹⁸ J.
  2. In eV: 6.02 × 10⁻¹⁸/1.602 × 10⁻¹⁹ = 37.6 eV.
  3. E₂ = 4E₁ = 150.4 eV.

Answer: E₁ ≈ 37.6 eV, E₂ ≈ 150 eV

Example: What wavelength does that electron emit when it drops from n = 2 to n = 1?

  1. ΔE = 3E₁ = 112.8 eV.
  2. λ = hc/ΔE = 1240 eV·nm/112.8 eV.

Answer: λ ≈ 11.0 nm (extreme ultraviolet)

Example: Repeat E₁ for a box 1 nm wide, and comment.

  1. E ∝ 1/L², and L is 10 times larger.
  2. E₁ = 37.6/100 = 0.376 eV.

Answer: 0.376 eV: a ten-fold wider box lowers the levels a hundred-fold

Matter shows wave behaviour with de Broglie wavelength λ = h/p. Because a particle is a wave packet, its position and momentum cannot both be sharp (Heisenberg). The state is described by a wave function ψ whose square |ψ|² is the probability density; ψ obeys the Schrödinger equation. Confining an electron in a box of width L allows only standing waves, so energy is quantised as Eₙ = n²h²/(8mL²).

  • de Broglie: λ = h/p = h/√(2mE); for an electron accelerated through V volts, λ = 1.226/√V nm.
  • Uncertainty: Δx·Δp ≥ ħ/2 (often written ≥ h/4π); also ΔE·Δt ≥ ħ/2.
  • Well-behaved ψ: single-valued, finite, continuous, with continuous first derivative; normalised ∫|ψ|²dx = 1.
  • Phase velocity of a matter wave exceeds c, but the group velocity of the wave packet equals the particle velocity.
  • Particle in a box: ψₙ = √(2/L) sin(nπx/L), n = 1, 2, 3…; zero-point energy E₁ ≠ 0; n − 1 nodes inside the box.
  • Time-independent form −(ħ²/2m)ψ″ + Vψ = Eψ comes from separating ψ(x, t) = ψ(x)e^(−iEt/ħ).

Key formulas

  • λ = h/p = h/(mv)
  • Δx·Δp ≥ ħ/2
  • iħ ∂Ψ/∂t = −(ħ²/2m)∂²Ψ/∂x² + VΨ
  • Eₙ = n²h²/(8mL²)
  • ψₙ(x) = √(2/L) sin(nπx/L)

Practice questions

The de Broglie wavelength of a particle is

  1. h/p
  2. p/h
  3. hp
  4. h/E
Show the answer

Answer: A. h/p λ = h/p, the inverse of momentum.

For a particle in a 1-D box, the energy of level n is proportional to

  1. n
  2. n²
  3. 1/n²
  4. √n
Show the answer

Answer: B. n² Eₙ = n²h²/8mL².

|ψ|² represents

  1. energy
  2. momentum
  3. probability density
  4. charge
Show the answer

Answer: C. probability density Born interpretation.

The lowest energy of a particle in a box is

  1. zero
  2. h²/8mL²
  3. h²/4mL²
  4. infinite
Show the answer

Answer: B. h²/8mL² Zero-point energy for n = 1; it cannot be zero because of the uncertainty principle.

Theory questions

State Heisenberg’s uncertainty principle and write its mathematical form. (2 marks)

Show the model answer

Position and momentum (and energy and time) cannot be measured simultaneously with arbitrary precision: Δx·Δp ≥ ħ/2, ΔE·Δt ≥ ħ/2.

What are the conditions for a wave function to be acceptable (well-behaved)? (4 marks)

Show the model answer

ψ must be single-valued, finite everywhere, continuous, have a continuous first derivative (where V is finite), and be normalisable: ∫|ψ|²dx = 1.

Solve the time-independent Schrödinger equation for a particle in a one-dimensional box of width L. Obtain the energy eigenvalues and normalised wave functions and sketch the first three. (10 marks)

Show the model answer

Inside (V = 0): ψ″ + k²ψ = 0, k² = 2mE/ħ² ⇒ ψ = A sin kx + B cos kx. ψ(0) = 0 ⇒ B = 0; ψ(L) = 0 ⇒ kL = nπ. So Eₙ = n²π²ħ²/(2mL²) = n²h²/(8mL²). Normalising ∫₀ᴸ A² sin²(nπx/L) dx = 1 ⇒ A = √(2/L). Sketch: n = 1 half wave (no node), n = 2 one node, n = 3 two nodes; energies in ratio 1 : 4 : 9.

Solids, Semiconductors and Superconductivity

Topics: Kronig–Penney model (qualitative), energy bands in metals, semiconductors and insulators, solar cell, LED, Hall effect; superconductors: Meissner effect, critical field, isotope effect, persistent current, levitation, Type-I and Type-II, BCS theory (qualitative).

Energy bands: Kronig–Penney model

In a crystal an electron moves through a periodic row of ion potentials. Kronig and Penney replaced them by a row of square wells and barriers and solved Schrödinger’s equation. The result is an equation of the form P sin(αa)/(αa) + cos(αa) = cos(ka), where the left side depends on energy and P measures barrier strength. Since cos(ka) lies between −1 and +1, only certain bands of energy are allowed, separated by forbidden gaps.

Two limits check the model. When P → 0 the barriers vanish and every energy is allowed: the free electron. When P → ∞ each well is isolated and the bands shrink to the sharp levels of a particle in a box. Real crystals lie between, and the bands widen as the energy rises because the higher electrons feel the barriers less.

Whether a solid conducts depends on how the bands are filled. In a metal the highest occupied band is only partly filled (or overlaps the next), so electrons find empty states next to them and move freely under a field. In an insulator a full valence band is separated from an empty conduction band by a wide gap (several eV). A semiconductor has the same picture with a narrow gap (about 1 eV), so heat or light lifts some electrons across.

  • Periodic potential ⇒ allowed bands and forbidden gaps
  • P → 0: free electron; P → ∞: particle in a box
  • Metal: partly filled band
  • Insulator: gap of several eV (diamond 5.5 eV)
  • Semiconductor: gap about 1 eV (Si 1.12 eV, Ge 0.67 eV)

Example: Silicon has a band gap of 1.12 eV. What is the longest wavelength it can absorb to create an electron–hole pair?

  1. λ = hc/E_g = 1240 eV·nm/1.12 eV.
  2. λ ≈ 1107 nm.

Answer: About 1.1 µm, in the near infrared

Example: Diamond has E_g = 5.5 eV. Explain why it is transparent.

  1. Its absorption edge is at 1240/5.5 = 225 nm, in the ultraviolet.
  2. Visible photons (1.6–3.1 eV) cannot lift an electron across the gap, so they pass through.

Answer: Visible light lacks the energy to cross the 5.5 eV gap

Semiconductors, the solar cell and the LED

A pure (intrinsic) semiconductor has equal numbers of electrons and holes. Doping with a group-V element adds donor electrons (n-type); a group-III element adds holes (p-type). Where p and n regions meet, carriers diffuse across and leave a depletion region with a built-in field. This p–n junction is the basis of both the solar cell and the LED, which do opposite jobs.

In a solar cell, photons with energy above the gap create electron–hole pairs; the built-in field sweeps them apart and drives current through an external load. Its I–V curve is characterised by the short-circuit current I_sc, the open-circuit voltage V_oc, and the fill factor FF = P_max/(I_sc V_oc). The efficiency is P_max divided by the incident light power.

An LED runs the other way: under forward bias, electrons and holes recombine across the junction and emit photons of energy close to the band gap, λ ≈ hc/E_g. Direct-gap materials such as GaAs, GaAsP and InGaN emit efficiently, and the colour is chosen by the alloy composition. Silicon has an indirect gap and makes a poor light emitter.

  • n-type: donors (P, As); p-type: acceptors (B, Al)
  • Solar cell: light → pairs → current; FF = P_max/(I_sc V_oc)
  • Efficiency = P_max/light power
  • LED: recombination → light; λ ≈ hc/E_g
  • Direct gap emits well; silicon does not

Example: A solar cell has V_oc = 0.6 V, I_sc = 3 A and FF = 0.75. Its area is 100 cm² under 1000 W/m². Find P_max and the efficiency.

  1. P_max = FF × V_oc × I_sc = 0.75 × 0.6 × 3 = 1.35 W.
  2. Light power = 1000 × 0.01 = 10 W.
  3. η = 1.35/10 = 13.5 %.

Answer: 1.35 W; 13.5 %

Example: An LED is made of GaAsP with a band gap of 1.9 eV. What colour does it give?

  1. λ = 1240/1.9 nm.
  2. λ ≈ 653 nm.

Answer: Red (about 653 nm)

Hall effect

When a current-carrying slab is placed in a magnetic field perpendicular to the current, the moving charges are pushed sideways by the force qv × B. They pile up on one face until the electric field of the piled-up charge balances the magnetic push: eE_H = evB. The voltage across the slab in that steady state is the Hall voltage, V_H = IB/(n e t), where t is the thickness along B.

The sign of V_H shows whether the carriers are negative (electrons) or positive (holes), the original proof that holes behave as positive charges. The Hall coefficient R_H = 1/(ne) gives the carrier density, and combined with the conductivity σ it gives the mobility μ = σR_H, the drift speed per unit field.

Because V_H is proportional to B, Hall probes measure magnetic fields. Hall sensors also count wheel rotations in vehicles, detect the position of brushless-motor rotors, and measure current without breaking the circuit. Semiconductors give much larger Hall voltages than metals because n is far smaller.

  • Steady state: eE_H = evB
  • V_H = IB/(n e t)
  • R_H = 1/(ne); sign gives the carrier type
  • Mobility μ = σR_H
  • Uses: field probes, speed and position sensors, current sensors

Example: A semiconductor slab 1 mm thick has n = 10²² m⁻³ and carries 10 mA in a field of 0.5 T. Find V_H and R_H.

  1. V_H = IB/(net) = 0.01 × 0.5/(10²² × 1.602 × 10⁻¹⁹ × 10⁻³) = 0.005/1.602.
  2. V_H = 3.12 × 10⁻³ V.
  3. R_H = 1/(ne) = 1/1602 = 6.24 × 10⁻⁴ m³/C.

Answer: V_H ≈ 3.12 mV; R_H ≈ 6.24 × 10⁻⁴ m³/C

Example: If the same sample has conductivity 100 S/m, find the mobility of its carriers.

  1. μ = σR_H = 100 × 6.24 × 10⁻⁴.
  2. μ = 0.0624 m²/(V·s).

Answer: 0.0624 m²/(V·s)

Superconductivity

Many metals and compounds lose all electrical resistance below a critical temperature T_c (mercury at 4.2 K, lead at 7.2 K, some cuprate ceramics above 77 K). A current started in a superconducting ring keeps flowing for years with no source: a persistent current. Superconductivity is destroyed by a strong enough field, H_c(T) = H₀[1 − (T/T_c)²], and therefore also by a large current, whose own field reaches H_c at the surface (Silsbee’s rule: I_c = 2πrH_c for a wire).

A superconductor is more than a perfect conductor: cooled in a field, it expels the field from its interior (the Meissner effect), becoming a perfect diamagnet. This is why a small magnet floats above a cooled superconductor. Type-I superconductors (pure metals) expel the field completely up to H_c and then turn normal at once. Type-II materials (alloys, ceramics) let the field enter in quantised vortices between a lower H_c1 and an upper H_c2, and stay superconducting to very high fields, so they are used for magnets.

The isotope effect, T_c ∝ M^(−1/2), shows that the vibrating lattice is involved. BCS theory explains it: an electron distorts the lattice and a second electron is attracted to the distortion, forming a Cooper pair. The pairs share one quantum state and move without scattering, and breaking a pair needs an energy gap of a few meV. Applications include MRI magnets, maglev trains, SQUID magnetometers and lossless cables.

  • Zero resistance below T_c; persistent currents
  • H_c(T) = H₀[1 − (T/T_c)²]; I_c = 2πrH_c
  • Meissner effect: B = 0 inside, levitation
  • Type I sharp H_c; Type II vortices between H_c1 and H_c2
  • Isotope effect T_c ∝ M^(−1/2); BCS Cooper pairs

Example: Lead has T_c = 7.2 K and H₀ = 6.5 × 10⁴ A/m. Find the critical field at 4.2 K.

  1. (T/T_c)² = (4.2/7.2)² = 0.340.
  2. H_c = 6.5 × 10⁴ × (1 − 0.340) = 4.29 × 10⁴ A/m.

Answer: 4.29 × 10⁴ A/m

Example: What is the largest current a lead wire of radius 1 mm can carry at 4.2 K without losing superconductivity?

  1. Silsbee: I_c = 2πrH_c.
  2. I_c = 2π × 10⁻³ × 4.29 × 10⁴ = 269 A.

Answer: About 269 A

Example: Mercury of mean isotopic mass 199.5 has T_c = 4.185 K. Estimate T_c for a sample of mass 203.4.

  1. T_c ∝ M^(−1/2), so T_c₂ = T_c₁ √(M₁/M₂).
  2. T_c₂ = 4.185 × √(199.5/203.4) = 4.185 × 0.9904.

Answer: ≈ 4.145 K

In a crystal the periodic potential (Kronig–Penney model) splits allowed electron energies into bands separated by forbidden gaps. Metals have a partly filled band or overlapping bands, semiconductors a small gap (~1 eV) and insulators a large gap (> 3 eV). A p-n junction can convert light to current (solar cell) or current to light (LED). In the Hall effect a magnetic field deflects carriers, giving a transverse voltage that reveals carrier type and density. Below a critical temperature some materials lose all resistance and expel magnetic fields (Meissner effect).

  • Band gap: Si 1.1 eV, Ge 0.67 eV, diamond ~5.5 eV; Eg decides conductivity and LED colour (λ = hc/Eg).
  • Solar cell: photons with E > Eg create electron–hole pairs that the junction field separates; key figures are Voc, Isc, fill factor and efficiency.
  • Hall voltage V_H = BI/(nqt); Hall coefficient R_H = 1/(nq): negative for electrons, positive for holes.
  • Meissner effect: a superconductor is a perfect diamagnet (χ = −1, B = 0 inside).
  • Critical field Hc(T) = H₀[1 − (T/Tc)²]; isotope effect Tc·M^α = constant (α ≈ 0.5), evidence for electron–phonon coupling.
  • Type-I: one sharp Hc, soft; Type-II: Hc1 and Hc2 with a mixed (vortex) state, used in magnets. BCS: Cooper pairs bound through lattice vibrations.

Key formulas

  • V_H = BI/(n q t)
  • R_H = 1/(n q)
  • Hc(T) = H₀[1 − (T/Tc)²]
  • λ(LED) = hc/Eg ≈ 1240/Eg(eV) nm

Practice questions

A semiconductor has a band gap of about

  1. 0 eV
  2. 1 eV
  3. 10 eV
  4. 100 eV
Show the answer

Answer: B. 1 eV Si 1.1 eV, Ge 0.67 eV.

The Meissner effect shows that a superconductor is

  1. paramagnetic
  2. ferromagnetic
  3. a perfect diamagnet
  4. non-magnetic
Show the answer

Answer: C. a perfect diamagnet It expels flux: B = 0 inside, χ = −1.

A positive Hall coefficient indicates

  1. electrons are majority carriers
  2. holes are majority carriers
  3. a metal
  4. zero current
Show the answer

Answer: B. holes are majority carriers R_H = 1/(nq) is positive for positive carriers.

Type-II superconductors have

  1. one critical field
  2. two critical fields
  3. no critical field
  4. negative Tc
Show the answer

Answer: B. two critical fields Lower Hc1 and upper Hc2 with a mixed state between.

Theory questions

Distinguish between metals, semiconductors and insulators on the basis of band theory. (4 marks)

Show the model answer

Metals: conduction band partly filled or valence and conduction bands overlap, no gap. Semiconductors: filled valence band, empty conduction band at 0 K, small gap (~1 eV) so carriers are thermally excited at room temperature. Insulators: large gap (> 3 eV), essentially no carriers.

What is the Hall effect? Derive the expression for Hall voltage and give two applications. (8 marks)

Show the model answer

A current-carrying conductor in a perpendicular magnetic field develops a transverse voltage. In equilibrium qE_H = qvB with I = nqvA ⇒ E_H = BI/(nqA), V_H = E_H·w = BI/(nqt). Uses: find carrier type and concentration, mobility (μ = σR_H), magnetic field sensors (Hall probes), current sensors.

Explain the Meissner effect, critical field and isotope effect. Compare Type-I and Type-II superconductors. (10 marks)

Show the model answer

Meissner: below Tc flux is expelled, perfect diamagnetism. Critical field Hc(T) = H₀(1 − T²/Tc²) destroys superconductivity. Isotope effect Tc ∝ M^(−1/2) shows lattice involvement (BCS). Type-I: single Hc, complete Meissner state, low Hc, mostly pure metals (Pb, Hg). Type-II: Hc1 < H < Hc2 mixed state with flux vortices, high Hc2, alloys/ceramics (NbTi, YBCO), used in MRI magnets.

Lasers, Fibre Optics and Acoustics

Topics: Absorption, spontaneous and stimulated emission, Einstein coefficients, population inversion, pumping, metastable state, He–Ne laser, applications; optical fibre principle and structure, numerical aperture and acceptance angle, single/multimode, step/graded index, communication system; Weber–Fechner law, reverberation, Sabine’s formula, absorption coefficient, acoustics of buildings.

Absorption, spontaneous and stimulated emission

An atom with levels E₁ and E₂ interacts with light of frequency ν = (E₂ − E₁)/h in three ways. In absorption a photon lifts the atom up. In spontaneous emission an excited atom drops on its own, emitting a photon in a random direction and phase. In stimulated emission a passing photon triggers the drop, and the new photon is an exact copy: same frequency, direction, phase and polarisation. The last is what makes a laser possible.

Einstein described the rates with coefficients: absorption B₁₂ρN₁, spontaneous emission A₂₁N₂, stimulated emission B₂₁ρN₂, where ρ is the energy density of radiation at ν. Requiring these to balance in thermal equilibrium and to reproduce Planck’s law gives B₁₂ = B₂₁ and A₂₁/B₂₁ = 8πhν³/c³.

The ratio of spontaneous to stimulated emission in thermal radiation is e^(hν/kT) − 1. For visible light at room temperature this is enormous, so ordinary sources are almost entirely spontaneous and incoherent. Since A/B rises as ν³, lasers become much harder to make at short (X-ray) wavelengths.

  • Absorption, spontaneous emission, stimulated emission
  • Stimulated photon: same ν, direction, phase, polarisation
  • B₁₂ = B₂₁; A₂₁/B₂₁ = 8πhν³/c³
  • Spontaneous/stimulated = e^(hν/kT) − 1
  • Short wavelengths: harder lasing

Example: Find the ratio of spontaneous to stimulated emission for 600 nm light at 300 K.

  1. hν = hc/λ = 3.31 × 10⁻¹⁹ J; kT = 4.14 × 10⁻²¹ J.
  2. hν/kT = 79.9.
  3. Ratio = e^79.9 − 1 ≈ 5 × 10³⁴.

Answer: About 5 × 10³⁴: stimulated emission is negligible

Example: Find the photon energy of the He–Ne laser line at 632.8 nm.

  1. E = hc/λ = 6.626 × 10⁻³⁴ × 3.00 × 10⁸/632.8 × 10⁻⁹ = 3.14 × 10⁻¹⁹ J.
  2. In eV: 3.14 × 10⁻¹⁹/1.602 × 10⁻¹⁹.

Answer: 1.96 eV

Population inversion and the He–Ne laser

Light is amplified only if stimulated emission outpaces absorption, which needs more atoms in the upper level than the lower: a population inversion. In thermal equilibrium N₂/N₁ = e^(−ΔE/kT), always less than one, so inversion must be forced by pumping: optical (flash lamp), electrical discharge, or chemical. A two-level system cannot be inverted by optical pumping, because absorption and stimulated emission then balance.

Three- and four-level schemes solve this with a metastable state, a level with a long lifetime (around a millisecond rather than ten nanoseconds) where atoms accumulate. An optical resonator, two mirrors facing each other, one partly transmitting, sends the photons back through the medium many times so that the stimulated chain builds up along the axis and a narrow, directional, coherent beam emerges.

In the He–Ne laser an electric discharge excites helium atoms to metastable levels that happen to match levels of neon. Collisions hand the energy to neon, creating an inversion relative to a lower neon level that empties quickly. The 632.8 nm red line results. It is a continuous, low-power (about 1 mW) four-level gas laser. Laser uses include fibre communication, barcode scanners, surveying and alignment, eye and skin surgery, cutting and welding, holography and LIDAR.

  • Inversion: N₂ > N₁; thermally N₂/N₁ = e^(−ΔE/kT)
  • Pumping: optical, electrical, chemical
  • Metastable level: long-lived store of excited atoms
  • Resonator: two mirrors, one partly transmitting
  • He–Ne: He excites Ne; 632.8 nm, continuous, four-level

Example: A He–Ne laser emits 1 mW at 632.8 nm. How many photons leave per second?

  1. Energy per photon = 3.14 × 10⁻¹⁹ J.
  2. n = 10⁻³/3.14 × 10⁻¹⁹.

Answer: ≈ 3.2 × 10¹⁵ photons per second

Example: At 300 K, what is the thermal ratio N₂/N₁ for levels 1.96 eV apart? What does it show?

  1. kT = 0.0259 eV, so ΔE/kT = 75.8.
  2. N₂/N₁ = e^(−75.8) ≈ 1.2 × 10⁻³³.
  3. The upper level is practically empty; heating can never invert it.

Answer: ≈ 10⁻³³: inversion needs pumping

Optical fibres

An optical fibre guides light by total internal reflection. A glass core of index n₁ is surrounded by cladding of slightly lower index n₂; rays striking the core–cladding boundary beyond the critical angle sin⁻¹(n₂/n₁) are reflected without loss and zigzag along the fibre, even round gentle bends. A protective buffer coating surrounds the cladding.

Only rays entering within a cone are trapped. The half-angle of this acceptance cone, in air, satisfies sin θₐ = √(n₁² − n₂²), called the numerical aperture NA. The relative index difference Δ = (n₁ − n₂)/n₁ gives NA ≈ n₁√(2Δ). The number of paths (modes) a fibre carries is set by the V-number, V = 2πa NA/λ, where a is the core radius; a step-index fibre is single-mode if V < 2.405 and carries about V²/2 modes when V is large.

In a step-index multimode fibre, steep rays travel farther than axial ones and pulses spread (intermodal dispersion). A graded-index fibre, whose core index falls gradually from the axis, lets the outer rays travel faster and equalises the times. Single-mode fibres (core about 8–10 µm) avoid intermodal dispersion and carry long-distance traffic. A communication link has a transmitter (laser or LED), the fibre with repeaters or amplifiers, and a photodiode receiver. Loss is quoted in dB/km.

  • Core n₁ > cladding n₂; total internal reflection
  • NA = sin θₐ = √(n₁² − n₂²) ≈ n₁√(2Δ)
  • V = 2πa NA/λ; single-mode if V < 2.405; modes ≈ V²/2
  • Step-index vs graded-index; single-mode vs multimode
  • Loss in dB = 10 log(P_in/P_out)

Example: A fibre has n₁ = 1.50 and n₂ = 1.46. Find NA, the acceptance angle, Δ and the critical angle.

  1. NA = √(2.25 − 2.1316) = √0.1184 = 0.344.
  2. θₐ = sin⁻¹ 0.344 = 20.1°.
  3. Δ = 0.04/1.50 = 0.0267.
  4. Critical angle = sin⁻¹(1.46/1.50) = 76.7°.

Answer: NA 0.344; 20.1°; Δ 0.0267; 76.7°

Example: The same fibre has a 25 µm core radius and carries 1.3 µm light. Find V and the approximate number of modes.

  1. V = 2π × 25 × 0.344/1.3 = 41.6.
  2. Modes ≈ V²/2 = 865.

Answer: V ≈ 41.6; about 860 modes (multimode)

Example: A 10 km link loses 0.3 dB/km. If 1 mW goes in, how much comes out?

  1. Total loss = 3 dB.
  2. 3 dB is a factor of 10^0.3 ≈ 2.

Answer: About 0.5 mW

Acoustics of buildings

The ear responds to sound intensity roughly logarithmically: the Weber–Fechner law says the sensation grows as the logarithm of the stimulus. Hence loudness levels are measured in decibels, L = 10 log₁₀(I/I₀), with I₀ = 10⁻¹² W/m², the threshold of hearing. Doubling the intensity adds only 3 dB, and every 10 dB is a ten-fold rise in intensity.

In a closed hall, sound reflects many times from walls, floor, ceiling and audience, so it persists after the source stops. The reverberation time T is the time for the level to fall by 60 dB (to a millionth of the intensity). Too long and speech blurs into echoes; too short and the hall sounds dead. Typical targets are about 0.5–1 s for lecture rooms and 1.5–2 s for concert halls.

Sabine found that T = 0.161V/A (SI units), where V is the volume and A = Σαᵢsᵢ the total absorption, each surface area multiplied by its absorption coefficient (an open window has α = 1; that unit is the sabin). Good acoustic design also needs adequate loudness everywhere, no echoes or focusing from curved surfaces, no resonance, and low external noise. Absorption is added with porous panels, curtains, carpets and upholstered seats.

  • Weber–Fechner: sensation ∝ log(intensity)
  • L = 10 log(I/I₀) dB; ×2 intensity = +3 dB
  • T = time for a 60 dB fall
  • Sabine: T = 0.161V/Σαs
  • Fix: absorbers, no curved focusing surfaces, noise control

Example: A 2000 m³ hall has total absorption 200 m² sabins. Find T, and T after adding 100 m² sabins of panels.

  1. T = 0.161 × 2000/200 = 1.61 s.
  2. With 300 m²: T = 0.161 × 2000/300 = 1.07 s.

Answer: 1.61 s, falling to 1.07 s

Example: A 1500 m³ hall has walls 500 m² (α 0.02), carpet 200 m² (0.3), seated audience 300 m² (0.5) and ceiling 100 m² (0.04). Find T.

  1. A = 10 + 60 + 150 + 4 = 224 m² sabins.
  2. T = 0.161 × 1500/224.

Answer: T ≈ 1.08 s

Example: By how many decibels does the level rise when the intensity doubles?

  1. ΔL = 10 log₁₀ 2.
  2. ΔL = 3.01 dB.

Answer: ≈ 3 dB

A laser amplifies light by stimulated emission, which needs population inversion — more atoms in an upper (metastable) level than the lower one — achieved by pumping. The He–Ne laser uses helium to transfer energy to neon, emitting 632.8 nm. An optical fibre guides light by total internal reflection in a core of higher refractive index than the cladding; only rays inside the acceptance cone (NA = √(n₁² − n₂²)) are guided. In a hall, sound persists by reflection; Sabine’s reverberation time T = 0.161V/A must suit the use of the hall.

  • Einstein relations: A₂₁/B₂₁ = 8πhν³/c³ and B₁₂ = B₂₁; stimulated photons have the same phase, frequency, direction and polarisation.
  • Laser light is monochromatic, coherent, highly directional and intense.
  • He–Ne: four-level gas laser, continuous output at 632.8 nm, pumped by electric discharge.
  • NA = √(n₁² − n₂²) = sin θ_a; relative index difference Δ = (n₁ − n₂)/n₁; NA ≈ n₁√(2Δ).
  • Step-index: abrupt core index; graded-index: parabolic index reduces modal dispersion. Single-mode fibres have small cores (~8 µm).
  • Sabine: T = 0.161V/ΣαS (SI); good hall: right reverberation, no echoes or focusing, uniform loudness, low noise.

Key formulas

  • NA = sin θ_a = √(n₁² − n₂²)
  • Δ = (n₁ − n₂)/n₁
  • T = 0.161 V / Σ αᵢSᵢ
  • L = 10 log₁₀(I/I₀) dB

Practice questions

Population inversion means

  1. N₁ > N₂
  2. N₂ > N₁
  3. N₁ = N₂
  4. N₂ = 0
Show the answer

Answer: B. N₂ > N₁ More atoms in the upper level than the lower one.

The He–Ne laser emits at

  1. 694.3 nm
  2. 632.8 nm
  3. 1064 nm
  4. 10.6 µm
Show the answer

Answer: B. 632.8 nm 694.3 nm is ruby, 1064 nm Nd:YAG, 10.6 µm CO₂.

Numerical aperture of a fibre with n₁ = 1.5, n₂ = 1.48 is about

  1. 0.02
  2. 0.24
  3. 0.5
  4. 1.2
Show the answer

Answer: B. 0.24 √(2.25 − 2.19) = 0.245.

Sabine’s reverberation time is proportional to

  1. total absorption
  2. volume of the hall
  3. 1/volume
  4. frequency
Show the answer

Answer: B. volume of the hall T = 0.161V/A.

Theory questions

What is a metastable state? Why is it needed in a laser? (2 marks)

Show the model answer

A long-lived excited level (~10⁻³ s compared with ~10⁻⁸ s). Atoms accumulate there, making population inversion possible so stimulated emission can dominate.

Define numerical aperture and acceptance angle of an optical fibre and derive NA = √(n₁² − n₂²). (6 marks)

Show the model answer

Acceptance angle θ_a: maximum angle to the axis at which a ray is guided. At entry n₀ sin θ_a = n₁ sin θ_r; at the core–cladding boundary the angle (90° − θ_r) must equal the critical angle: sin(90° − θ_r) = n₂/n₁ ⇒ cos θ_r = n₂/n₁. So n₀ sin θ_a = n₁√(1 − n₂²/n₁²) = √(n₁² − n₂²) = NA (n₀ = 1 for air).

Explain with an energy-level diagram the construction and working of the He–Ne laser. Give three applications of lasers. (10 marks)

Show the model answer

Discharge tube with He:Ne ≈ 10:1, Brewster windows, optical resonator. Electrons excite He to metastable 2¹S and 2³S levels; resonant collisions transfer energy to Ne 3s and 2s levels (population inversion relative to 2p). Transitions 3s→2p give 632.8 nm; 2p atoms decay to 1s and return to ground by wall collisions. Continuous, coherent red output. Applications: barcode scanners, alignment/surveying, holography, eye surgery, fibre communication, material cutting (CO₂).

Electromagnetism and Dielectric Materials

Topics: Polar and non-polar molecules, dielectric polarisation and its types, polarisability, D = ε₀E + P, Gauss’s law in dielectrics, Clausius–Mossotti relation, frequency dependence; gradient, divergence, curl; Laplace and Poisson equations; continuity equation, displacement current, Maxwell’s equations.

Dielectric polarisation

A dielectric is an insulator whose charges cannot flow but can shift slightly under a field. Molecules are non-polar if their centres of positive and negative charge coincide (H₂, O₂, CO₂, CH₄) and polar if they carry a permanent dipole (H₂O, HCl, NH₃). An applied field E induces dipoles in non-polar molecules and partly aligns the existing dipoles of polar ones.

The dipole moment per unit volume is the polarisation P. Polarisation leaves bound charges on the surfaces that oppose the applied field, which is why a dielectric between capacitor plates lowers the field and raises the capacitance by the factor εᵣ (the dielectric constant). For a linear dielectric P = ε₀χE with susceptibility χ = εᵣ − 1.

The displacement D = ε₀E + P = ε₀εᵣE depends only on the free charges. Gauss’s law in a dielectric reads ∮D·dA = Q_free, so bound charges need not be tracked. At the molecular level each molecule acquires p = αE_local, where α is the polarisability; for a dilute gas with N molecules per m³, P = NαE and so ε₀(εᵣ − 1) = Nα.

  • Non-polar vs polar molecules
  • P = dipole moment per volume = ε₀(εᵣ − 1)E
  • D = ε₀E + P = ε₀εᵣE
  • Gauss: ∮D·dA = Q_free
  • p = αE; dilute gas: ε₀(εᵣ − 1) = Nα

Example: A dielectric with εᵣ = 4 is in a field of 10⁵ V/m. Find P and D.

  1. P = ε₀(εᵣ − 1)E = 8.854 × 10⁻¹² × 3 × 10⁵ = 2.66 × 10⁻⁶ C/m².
  2. D = ε₀εᵣE = 8.854 × 10⁻¹² × 4 × 10⁵ = 3.54 × 10⁻⁶ C/m².
  3. Check: ε₀E + P = 0.89 + 2.66 = 3.54 (× 10⁻⁶).

Answer: P ≈ 2.66 × 10⁻⁶ C/m²; D ≈ 3.54 × 10⁻⁶ C/m²

Example: A gas has 2.7 × 10²⁵ molecules/m³ and εᵣ = 1.0005. Find the polarisability of one molecule.

  1. α = ε₀(εᵣ − 1)/N.
  2. α = 8.854 × 10⁻¹² × 5 × 10⁻⁴/2.7 × 10²⁵.

Answer: α ≈ 1.64 × 10⁻⁴⁰ F·m²

Types of polarisation, Clausius–Mossotti relation and frequency dependence

Four mechanisms contribute. Electronic polarisation shifts the electron cloud against the nucleus (in every material, α_e = 4πε₀R³ for a simple atom). Ionic polarisation displaces positive and negative ions in a crystal such as NaCl. Orientation polarisation aligns permanent dipoles against thermal agitation, so it falls with temperature as 1/T. Space-charge polarisation piles charge at interfaces and grain boundaries.

In a dense solid or liquid a molecule feels the applied field plus the field of its polarised neighbours. For a cubic arrangement this local (Lorentz) field is E + P/(3ε₀). Using it gives the Clausius–Mossotti relation (εᵣ − 1)/(εᵣ + 2) = Nα/(3ε₀), which links a measured bulk constant to a molecular property.

Each mechanism needs time to respond, so it drops out above a characteristic frequency: space charge above about 10³ Hz, orientation above about 10¹⁰ Hz (microwaves), ionic above about 10¹³ Hz (infrared), and electronic only in the ultraviolet. At optical frequencies only electronic polarisation remains, so εᵣ ≈ n². Near each fall-off the material absorbs energy (dielectric loss), the principle of microwave heating of water.

  • Electronic, ionic, orientation, space-charge
  • Orientation ∝ 1/T
  • Local field E + P/(3ε₀)
  • Clausius–Mossotti: (εᵣ − 1)/(εᵣ + 2) = Nα/(3ε₀)
  • At optical frequencies εᵣ ≈ n²; loss peaks at each fall-off

Example: A solid with 3 × 10²⁸ molecules/m³ has εᵣ = 1.5. Find α using Clausius–Mossotti.

  1. (εᵣ − 1)/(εᵣ + 2) = 0.5/3.5 = 0.1429.
  2. α = 3ε₀ × 0.1429/N = 3 × 8.854 × 10⁻¹² × 0.1429/3 × 10²⁸.
  3. α = 1.27 × 10⁻⁴⁰ F·m².

Answer: ≈ 1.27 × 10⁻⁴⁰ F·m²

Example: Water has static εᵣ ≈ 80 but refractive index 1.33. Explain the difference.

  1. At optical frequencies εᵣ ≈ n² = 1.77.
  2. The large static value comes from orienting the polar H₂O molecules, which cannot follow a field oscillating at 10¹⁴–10¹⁵ Hz.

Answer: Orientation polarisation is lost at optical frequencies

Gradient, divergence and curl

The operator ∇ = î∂/∂x + ĵ∂/∂y + k̂∂/∂z turns fields into fields. Acting on a scalar φ it gives the gradient ∇φ, a vector pointing in the direction of steepest increase with magnitude equal to that rate; in electrostatics E = −∇V. The derivative of φ in a direction n̂ is ∇φ·n̂.

The divergence ∇·F = ∂Fx/∂x + ∂Fy/∂y + ∂Fz/∂z measures how much a vector field spreads out from a point: positive at a source, negative at a sink, zero for a field with no sources. Gauss’s divergence theorem says the total outward flux through a closed surface equals the integral of ∇·F over the enclosed volume.

The curl ∇ × F measures the local rotation of a field, its direction being the axis of spin by the right-hand rule. A field with zero curl everywhere (such as an electrostatic field) is conservative and can be written as a gradient. Stokes’ theorem says the circulation of F round a loop equals the flux of ∇ × F through any surface it bounds. These two theorems turn Maxwell’s integral laws into differential form.

  • ∇φ: steepest rise; E = −∇V
  • ∇·F: source strength; divergence theorem
  • ∇ × F: rotation; Stokes’ theorem
  • Curl-free ⇒ conservative (F = ∇φ)
  • ∇·(∇ × F) = 0; ∇ × (∇φ) = 0

Example: Find ∇φ for φ = x²y + yz at the point (1, 2, 1).

  1. ∂φ/∂x = 2xy = 4.
  2. ∂φ/∂y = x² + z = 2.
  3. ∂φ/∂z = y = 2.

Answer: ∇φ = 4î + 2ĵ + 2k̂

Example: Find the divergence of F = x²î + y²ĵ + z²k̂ at (1, 1, 1), and the curl of G = −yî + xĵ.

  1. ∇·F = 2x + 2y + 2z = 6 at (1, 1, 1).
  2. ∇ × G has only a z-part: ∂(x)/∂x − ∂(−y)/∂y = 1 + 1 = 2.

Answer: ∇·F = 6; ∇ × G = 2k̂ (a uniform rotation)

Laplace and Poisson equations, continuity, displacement current and Maxwell’s equations

Combining E = −∇V with Gauss’s law ∇·E = ρ/ε₀ gives Poisson’s equation ∇²V = −ρ/ε₀; in a charge-free region it becomes Laplace’s equation ∇²V = 0. With boundary values fixed, the solution is unique, which lets engineers find fields in capacitors, cables and electron tubes.

Charge is conserved: whatever leaves a volume through its surface reduces the charge inside, which gives the continuity equation ∇·J + ∂ρ/∂t = 0. Ampère’s law ∇ × B = μ₀J contradicts this when charge piles up (a charging capacitor), because the divergence of a curl is zero. Maxwell fixed it by adding the displacement current density ε₀∂E/∂t, so a changing electric field produces a magnetic field just as a current does.

Maxwell’s equations in differential form are: ∇·D = ρ (Gauss), ∇·B = 0 (no magnetic poles), ∇ × E = −∂B/∂t (Faraday), and ∇ × H = J + ∂D/∂t (Ampère–Maxwell). In empty space they combine into a wave equation with speed c = 1/√(μ₀ε₀) = 3.00 × 10⁸ m/s: light is an electromagnetic wave, with E and B perpendicular to each other and to the direction of travel. In a medium the speed becomes c/√(μᵣεᵣ).

  • Poisson ∇²V = −ρ/ε₀; Laplace ∇²V = 0
  • Continuity: ∇·J + ∂ρ/∂t = 0
  • Displacement current I_d = ε₀ dΦ_E/dt = C dV/dt in a capacitor
  • ∇·D = ρ, ∇·B = 0, ∇ × E = −∂B/∂t, ∇ × H = J + ∂D/∂t
  • c = 1/√(μ₀ε₀); in a medium c/√(μᵣεᵣ)

Example: A 2 µF capacitor’s voltage rises at 1000 V/s. Find the displacement current between its plates.

  1. Between the plates I_d = ε₀ dΦ_E/dt = C dV/dt.
  2. I_d = 2 × 10⁻⁶ × 1000 = 2 × 10⁻³ A, equal to the conduction current in the wires.

Answer: 2 mA

Example: If V = x² volts (x in metres) in a region, what charge density is present?

  1. ∇²V = d²V/dx² = 2 V/m².
  2. Poisson: ρ = −ε₀∇²V = −2 × 8.854 × 10⁻¹².

Answer: ρ ≈ −1.77 × 10⁻¹¹ C/m³

Example: Find c from μ₀ = 4π × 10⁻⁷ H/m and ε₀, and the speed in a non-magnetic medium with εᵣ = 4.

  1. c = 1/√(4π × 10⁻⁷ × 8.854 × 10⁻¹²) = 3.00 × 10⁸ m/s.
  2. v = c/√4 = 1.50 × 10⁸ m/s.

Answer: 3.00 × 10⁸ m/s; 1.50 × 10⁸ m/s

A dielectric placed in a field develops dipole moment per unit volume P (polarisation) by electronic, ionic and orientational mechanisms; the displacement D = ε₀E + P = ε₀εᵣE obeys Gauss’s law with free charge only. The Clausius–Mossotti relation links the microscopic polarisability to the dielectric constant. Maxwell added the displacement current ε₀∂E/∂t so that Ampère’s law agrees with charge conservation, predicting electromagnetic waves travelling at c = 1/√(μ₀ε₀).

  • Electronic (all materials), ionic (ionic crystals) and orientational (polar molecules, temperature dependent) polarisation; space-charge polarisation at interfaces.
  • P = ε₀χE, εᵣ = 1 + χ; D = ε₀E + P.
  • Clausius–Mossotti: (εᵣ − 1)/(εᵣ + 2) = Nα/(3ε₀).
  • At high frequency the slower mechanisms cannot follow the field: εᵣ falls (orientational fails at microwaves, ionic in IR, electronic in UV).
  • ∇·E = ρ/ε₀ and ∇²V = −ρ/ε₀ (Poisson), ∇²V = 0 where ρ = 0 (Laplace).
  • Continuity: ∇·J + ∂ρ/∂t = 0; displacement current density J_d = ∂D/∂t.

Key formulas

  • D = ε₀E + P = ε₀εᵣE
  • (εᵣ − 1)/(εᵣ + 2) = Nα/(3ε₀)
  • ∇·D = ρ_free, ∇·B = 0
  • ∇×E = −∂B/∂t, ∇×H = J + ∂D/∂t
  • c = 1/√(μ₀ε₀)

Practice questions

Which polarisation is present in all dielectrics?

  1. ionic
  2. orientational
  3. electronic
  4. space charge
Show the answer

Answer: C. electronic Every atom has electrons whose cloud shifts in a field.

The displacement current density is

  1. σE
  2. ∂D/∂t
  3. ∇×E
  4. ρv
Show the answer

Answer: B. ∂D/∂t Maxwell’s addition to Ampère’s law.

∇·B = 0 means

  1. no electric charge
  2. no magnetic monopoles
  3. B is constant
  4. no current
Show the answer

Answer: B. no magnetic monopoles Magnetic field lines are closed.

Orientational polarisation decreases with

  1. increasing temperature
  2. increasing field
  3. decreasing frequency
  4. increasing dipole moment
Show the answer

Answer: A. increasing temperature Thermal agitation randomises dipoles: α₀ = p²/(3kT).

Theory questions

Define polarisation vector and electric susceptibility. Write the relation between D, E and P. (3 marks)

Show the model answer

P = dipole moment per unit volume; P = ε₀χE where χ is the susceptibility; D = ε₀E + P = ε₀(1 + χ)E = ε₀εᵣE.

Derive the Clausius–Mossotti relation. (8 marks)

Show the model answer

Local (Lorentz) field E_loc = E + P/(3ε₀). Dipole moment per molecule p = αE_loc and P = Nα(E + P/3ε₀). With P = ε₀(εᵣ − 1)E: ε₀(εᵣ − 1)E = NαE[1 + (εᵣ − 1)/3] ⇒ (εᵣ − 1)/(εᵣ + 2) = Nα/(3ε₀).

Write Maxwell’s equations in differential form and explain the physical significance of each. Deduce the wave equation in free space. (10 marks)

Show the model answer

∇·D = ρ (Gauss: charge is the source of D); ∇·B = 0 (no monopoles); ∇×E = −∂B/∂t (Faraday induction); ∇×H = J + ∂D/∂t (Ampère–Maxwell, current and changing E produce B). In vacuum (ρ = 0, J = 0): ∇×(∇×E) = −μ₀ε₀∂²E/∂t² and ∇×∇×E = ∇(∇·E) − ∇²E = −∇²E ⇒ ∇²E = μ₀ε₀ ∂²E/∂t², a wave with speed c = 1/√(μ₀ε₀) = 3×10⁸ m/s.

Mechanics and Low-Temperature Physics

Topics: Elasticity and elastic constants, twisting couple on a wire, bending of beams, cantilever; non-inertial frames, rotating coordinates, five-term acceleration, centripetal and Coriolis acceleration (weather systems, Foucault pendulum); Joule–Thomson effect, liquefaction of air (Linde), liquefaction of helium, adiabatic demagnetisation, He-3 cryostat.

Elasticity and the elastic constants

A body that regains its shape when the load is removed is elastic. Within the proportional limit, stress is proportional to strain (Hooke’s law), and the constant depends on the kind of deformation. Young’s modulus Y is tensile stress over longitudinal strain; the bulk modulus K is pressure over volume strain; the rigidity (shear) modulus η, also written G, is shear stress over shear angle.

A stretched wire also gets thinner. Poisson’s ratio σ is the lateral strain divided by the longitudinal strain, theoretically between −1 and 0.5 and about 0.25–0.35 for most metals. The four constants are not independent: Y = 2η(1 + σ), Y = 3K(1 − 2σ) and 9/Y = 1/K + 3/η.

The stress–strain curve of a ductile metal rises straight to the proportional limit, then to the elastic limit and yield point, after which the metal flows plastically, hardens to the ultimate stress and finally necks and breaks. Brittle materials break soon after the elastic region. A stretched wire stores energy ½ × stress × strain per unit volume.

  • Y = stress/longitudinal strain; K = −p/(ΔV/V); η = shear stress/angle
  • σ = lateral strain/longitudinal strain
  • Y = 2η(1 + σ) = 3K(1 − 2σ)
  • Extension ΔL = FL/(AY)
  • Energy per volume = ½ stress × strain

Example: A steel wire 2 m long and 1 mm in diameter carries 100 N; Y = 2 × 10¹¹ Pa. Find the extension.

  1. A = π(0.5 × 10⁻³)² = 7.85 × 10⁻⁷ m².
  2. ΔL = FL/(AY) = 100 × 2/(7.85 × 10⁻⁷ × 2 × 10¹¹).
  3. ΔL = 1.27 × 10⁻³ m.

Answer: ≈ 1.27 mm

Example: For steel Y = 2 × 10¹¹ Pa and σ = 0.3. Find η and K.

  1. η = Y/(2(1 + σ)) = 2 × 10¹¹/2.6 = 7.69 × 10¹⁰ Pa.
  2. K = Y/(3(1 − 2σ)) = 2 × 10¹¹/1.2 = 1.67 × 10¹¹ Pa.

Answer: η ≈ 7.7 × 10¹⁰ Pa; K ≈ 1.67 × 10¹¹ Pa

Twisting couple on a wire; bending of beams and the cantilever

Twisting a wire of radius r and length l through an angle θ shears each thin cylindrical shell inside it. Adding up the shear stresses gives the restoring couple τ = (πηr⁴/2l)θ, so the couple per unit twist is C = πηr⁴/(2l). The fourth power of r means a wire twice as thick is sixteen times stiffer. A torsion pendulum, a disc of moment of inertia I on such a wire, oscillates with period T = 2π√(I/C), which is used to measure η.

When a beam bends, its upper fibres stretch and lower fibres compress (or the reverse), with a neutral surface in between that keeps its length. Fibres a distance z from it have strain z/R, where R is the radius of curvature, and the internal bending moment is YI/R, with I = ∫z² dA the geometrical moment of inertia of the cross-section: bd³/12 for a rectangle (d vertical), πr⁴/4 for a circle.

For a cantilever of length L fixed at one end and loaded with W at the free end, the bending moment at distance x from the fixed end is W(L − x); integrating the curvature twice gives the end depression δ = WL³/(3YI). Since δ ∝ L³/d³, depth matters far more than width, which is why girders and joists are deep and why an I-section puts most metal far from the neutral axis.

  • Couple per unit twist C = πηr⁴/(2l)
  • Torsion pendulum T = 2π√(I/C)
  • Bending moment = YI/R
  • I: bd³/12 (rectangle), πr⁴/4 (circle)
  • Cantilever end depression δ = WL³/(3YI)

Example: A wire of radius 0.5 mm and length 1 m has η = 8 × 10¹⁰ Pa. Find the couple per unit twist and the period of a disc with I = 10⁻³ kg·m² hung from it.

  1. C = π × 8 × 10¹⁰ × (0.5 × 10⁻³)⁴/(2 × 1) = 7.85 × 10⁻³ N·m/rad.
  2. T = 2π√(10⁻³/7.85 × 10⁻³) = 2π × 0.357.
  3. T = 2.24 s.

Answer: C ≈ 7.85 × 10⁻³ N·m/rad; T ≈ 2.24 s

Example: A steel cantilever 0.5 m long has a 2 cm wide, 0.5 cm deep rectangular section; Y = 2 × 10¹¹ Pa. Find the end depression under 10 N.

  1. I = bd³/12 = 0.02 × (0.005)³/12 = 2.08 × 10⁻¹⁰ m⁴.
  2. δ = WL³/(3YI) = 10 × 0.125/(3 × 2 × 10¹¹ × 2.08 × 10⁻¹⁰).
  3. δ = 1.25/125 = 0.01 m.

Answer: 10 mm

Non-inertial frames: centripetal and Coriolis acceleration

Newton’s laws hold only in inertial frames. In an accelerating or rotating frame, objects appear to be pushed by fictitious (pseudo) forces that are really the frame’s own acceleration seen from inside. In a frame accelerating at A, every body appears to feel −mA; in a lift starting upward you feel heavier for this reason.

For a frame rotating with angular velocity ω, the true acceleration a relates to the acceleration a′ seen in the frame by the five-term formula a = A₀ + a′ + 2ω × v′ + ω × (ω × r) + (dω/dt) × r: the frame origin’s acceleration, the relative acceleration, the Coriolis term, the centripetal term and the angular-acceleration term. Moved to the force side, these appear as the Coriolis force −2mω × v′ and the centrifugal force −mω × (ω × r).

On the rotating Earth (ω = 7.29 × 10⁻⁵ rad/s), the centrifugal term makes g slightly smaller at the equator and the Coriolis term deflects moving bodies to the right in the northern hemisphere, with horizontal size 2ωv sin λ at latitude λ. It makes winds spiral round low-pressure regions (anticlockwise cyclones in the north), and turns the swing plane of a Foucault pendulum once in (one sidereal day)/sin λ.

  • Pseudo force −mA in an accelerating frame
  • a = A₀ + a′ + 2ω × v′ + ω × (ω × r) + ω̇ × r
  • Coriolis −2mω × v′; centrifugal −mω × (ω × r)
  • Horizontal Coriolis acceleration 2ωv sin λ
  • Foucault period = 23.93 h/sin λ

Example: A car drives north at 30 m/s at latitude 26° N (around Guwahati). Find the horizontal Coriolis acceleration.

  1. a = 2ωv sin λ = 2 × 7.292 × 10⁻⁵ × 30 × sin 26°.
  2. a = 1.92 × 10⁻³ m/s², towards the right (east).

Answer: ≈ 1.9 × 10⁻³ m/s², to the right

Example: How long does a Foucault pendulum at latitude 26.2° take to turn its swing plane through 360°?

  1. T = 23.93 h/sin 26.2°.
  2. T = 23.93/0.4415 = 54.2 h.

Answer: About 54 h

Example: Find the centripetal acceleration of a point on the equator due to the Earth’s spin (R = 6.371 × 10⁶ m).

  1. a = ω²R = (7.292 × 10⁻⁵)² × 6.371 × 10⁶.
  2. a = 0.0339 m/s², about 0.35 % of g.

Answer: ≈ 0.034 m/s²

Low-temperature physics

When a real gas expands through a porous plug or valve from high to low pressure with no heat exchange (a throttling process at constant enthalpy), its temperature changes: the Joule–Thomson effect. Intermolecular attraction makes the gas cool as the molecules move apart, while their finite size works the other way. A van der Waals gas cools only below the inversion temperature Tᵢ = 2a/(Rb); nitrogen and oxygen are below it at room temperature, but hydrogen and helium must be pre-cooled first.

Linde’s process liquefies air by repeating throttling with regenerative cooling. Air is compressed to about 200 atm, cooled with water, and expanded through a valve; the slightly cooled gas flows back through a counter-current heat exchanger and pre-cools the incoming high-pressure gas. The cooling builds up pass after pass until part of the gas liquefies near 77–90 K. Kamerlingh Onnes first liquefied helium (4.2 K) in 1908 by pre-cooling it with liquid hydrogen before Joule–Thomson expansion; modern plants add expansion engines.

Below about 1 K other methods are needed. Adiabatic demagnetisation magnetises a paramagnetic salt at about 1 K in a strong field while heat flows to the helium bath, then isolates it and removes the field slowly; the magnetic moments randomise by drawing energy from the lattice, so the temperature falls to millikelvins (T_final ≈ T_initial × B_final/B_initial in the ideal case). A He-3 cryostat pumps on liquid helium-3, a lighter isotope with higher vapour pressure, to reach about 0.3 K.

  • Joule–Thomson: throttling at constant enthalpy
  • Inversion temperature Tᵢ = 2a/(Rb) (van der Waals)
  • Linde: compress, cool, throttle, counter-current pre-cooling
  • Helium: pre-cool with liquid H₂, then throttle (4.2 K)
  • Adiabatic demagnetisation (mK); He-3 cryostat (≈ 0.3 K)

Example: Estimate the inversion temperatures of nitrogen (a = 0.137 Pa·m⁶/mol², b = 3.87 × 10⁻⁵ m³/mol) and helium (a = 3.46 × 10⁻³, b = 2.38 × 10⁻⁵).

  1. N₂: Tᵢ = 2 × 0.137/(8.314 × 3.87 × 10⁻⁵) = 852 K.
  2. He: Tᵢ = 2 × 3.46 × 10⁻³/(8.314 × 2.38 × 10⁻⁵) = 35 K.
  3. Room temperature lies below the first and far above the second.

Answer: ≈ 852 K and 35 K: helium must be pre-cooled

Example: Estimate the Joule–Thomson cooling of nitrogen at 300 K for a 100 bar (10⁷ Pa) drop, with C_p = 29.1 J/(mol·K).

  1. ΔT ≈ (2a/RT − b)ΔP/C_p.
  2. 2a/RT − b = 1.099 × 10⁻⁴ − 3.87 × 10⁻⁵ = 7.12 × 10⁻⁵ m³/mol.
  3. ΔT ≈ 7.12 × 10⁻⁵ × 10⁷/29.1 = 24 K.

Answer: About 24 K per pass (a van der Waals estimate)

Example: A paramagnetic salt at 1 K in 1 T is demagnetised adiabatically to an effective internal field of 0.01 T. Estimate the final temperature.

  1. Ideal case: T_f = T_i × B_f/B_i.
  2. T_f = 1 × 0.01/1 = 0.01 K.

Answer: About 10 mK

Within the elastic limit stress ∝ strain, giving Young’s modulus Y, bulk modulus K, rigidity modulus η and Poisson’s ratio σ, which are interrelated. A twisted wire exerts a restoring couple C = πηr⁴θ/(2l); a bent beam resists with bending moment YI/R. In a rotating frame extra (fictitious) accelerations appear: centripetal ω×(ω×r) and Coriolis 2ω×v, which deflect winds and rotate the Foucault pendulum’s plane. Gases cool on throttling below their inversion temperature (Joule–Thomson), used in the Linde process; even lower temperatures come from adiabatic demagnetisation.

  • Y = 2η(1 + σ) = 3K(1 − 2σ); 9/Y = 1/K + 3/η; theoretical σ lies between −1 and 0.5.
  • Twisting couple per unit twist C = πηr⁴/(2l); bending moment = YI/R with I = bd³/12 for a rectangle, πr⁴/4 for a circle.
  • Cantilever end depression δ = WL³/(3YI).
  • a_inertial = a_rot + 2ω×v + ω×(ω×r) + (dω/dt)×r + A_origin (five terms).
  • Coriolis deflects moving air to the right in the northern hemisphere (cyclones rotate anticlockwise there).
  • Joule–Thomson coefficient μ = (∂T/∂P)_H; cooling only below the inversion temperature (He: ~40 K, so pre-cooling is needed).

Key formulas

  • Y = 2η(1 + σ) = 3K(1 − 2σ)
  • C = πηr⁴/(2l)
  • δ = WL³/(3YI)
  • a_cor = −2ω×v
  • T_i = 2a/(Rb) (van der Waals inversion temperature)

Practice questions

Relation between Y, η and σ is

  1. Y = 2η(1 + σ)
  2. Y = 3η(1 − 2σ)
  3. Y = η(1 + 2σ)
  4. Y = 2η(1 − σ)
Show the answer

Answer: A. Y = 2η(1 + σ) Standard relation among elastic constants.

The Coriolis acceleration is

  1. ω×r
  2. 2ω×v
  3. ω×(ω×r)
  4. v²/r
Show the answer

Answer: B. 2ω×v Magnitude 2ωv sin θ.

Hydrogen and helium warm up on throttling at room temperature because

  1. they are monatomic
  2. room temperature is above their inversion temperature
  3. they are ideal gases
  4. they have no attractions
Show the answer

Answer: B. room temperature is above their inversion temperature They must be pre-cooled below the inversion temperature.

Depression at the free end of a loaded cantilever varies as

  1. L
  2. L²
  3. L³
  4. L⁴
Show the answer

Answer: C. L³ δ = WL³/3YI.

Theory questions

Define Poisson’s ratio. Why can it not exceed 0.5? (3 marks)

Show the model answer

σ = lateral strain/longitudinal strain. From K = Y/[3(1 − 2σ)], K must be positive, so 1 − 2σ > 0 ⇒ σ < 0.5.

Derive the expression for the couple per unit twist of a cylindrical wire. (8 marks)

Show the model answer

Consider a thin cylindrical shell of radius x, thickness dx. Shear angle φ = xθ/l, shear stress = ηxθ/l, force = (ηxθ/l)(2πx dx), moment = 2πηθx³dx/l. Integrating 0→r: τ = πηr⁴θ/(2l), so C = πηr⁴/(2l).

Derive the five-term acceleration formula in a rotating frame and discuss the Coriolis force with two examples. (10 marks)

Show the model answer

For any vector (dA/dt)_in = (dA/dt)_rot + ω×A. Apply to r and then to v: a_in = a_rot + 2ω×v_rot + ω×(ω×r) + (dω/dt)×r, plus acceleration of the origin. Coriolis force −2mω×v: deflects winds and ocean currents (cyclones anticlockwise in the northern hemisphere), rotates the plane of a Foucault pendulum at rate ω sin λ, makes falling bodies land slightly east, erodes one river bank more.

Open this subject studio →