Equilibrium of Rigid Bodies
Topics: Free-body diagrams; supports and reactions; force systems; resultant of coplanar concurrent and non-concurrent forces; equilibrium conditions for concurrent and non-concurrent forces in space; Coulomb friction: inclined plane, ladder, wedge; virtual work: virtual displacement, principle and applications.
Free-body diagrams, supports and force systems
Statics begins with one habit: cut the body free from everything that touches it and draw every external force that those contacts exert. This free-body diagram (FBD) shows the weight at the centre of gravity, applied loads, and a reaction wherever a support or another body was removed. Internal forces between parts of the same body cancel in pairs and never appear on its FBD.
Each support replaces the restraint it provides. A roller or a smooth surface stops motion only along the normal, so it gives one force normal to the surface. A pin or hinge stops translation in every direction, so it gives two components (Hx, Hy) but no moment. A fixed (built-in) support also stops rotation, giving two forces and a moment. A cable or rope can only pull, along its own line.
Forces are classified by their lines of action. Coplanar forces lie in one plane; concurrent forces meet at a point; parallel forces have parallel lines; and a general (non-concurrent) system has none of these. Concurrent forces can be replaced by one resultant through the common point, found by resolving: R = √((ΣFx)² + (ΣFy)²) at an angle tan⁻¹(ΣFy/ΣFx), using the signs of the sums to decide the quadrant.
- FBD: isolate, then show weight, loads and every reaction
- Roller: 1 normal force; pin: 2 components; fixed: 2 forces + moment
- Cable: tension along the cable only
- Concurrent resultant: R = √((ΣFx)² + (ΣFy)²)
- Direction from tan⁻¹(ΣFy/ΣFx) with signs
Example: Forces of 50 N at 0°, 80 N at 60° and 40 N at 150° (measured anticlockwise from the x-axis) act at a point. Find the resultant.
- ΣFx = 50 + 80 cos 60° + 40 cos 150° = 50 + 40 − 34.64 = 55.36 N.
- ΣFy = 0 + 80 sin 60° + 40 sin 150° = 69.28 + 20 = 89.28 N.
- R = √(55.36² + 89.28²) = √11 035.6 = 105.1 N.
- θ = tan⁻¹(89.28/55.36) = 58.2°, in the first quadrant since both sums are positive.
Answer: R ≈ 105.1 N at 58.2° to the x-axis
Example: A ladder rests on a rough floor and leans on a smooth wall. List the forces on its FBD.
- Weight W acting down at its middle.
- At the floor: normal reaction N (up) and friction F (along the floor, towards the wall, opposing the slip).
- At the smooth wall: one normal reaction R, horizontal, pushing away from the wall.
Answer: Four forces: W, N, F and R
Moments, couples and the resultant of non-concurrent forces
The moment of a force about a point is its turning effect: M = F × d, where d is the perpendicular distance from the point to the line of action. In coordinates, a force (Fx, Fy) acting at (x, y) has moment M = xFy − yFx about the origin, positive anticlockwise. Varignon’s theorem says the moment of a resultant equals the sum of the moments of its components, so a force may be split into easy components before taking moments.
Two equal, opposite, parallel forces a distance d apart form a couple of moment Fd. A couple has no resultant force and the same moment about every point, so it can be moved anywhere in its plane. Any force can be moved to a new point if a couple equal to its moment about that point is added; this is how a general system reduces to a single force at a chosen point plus a couple.
For non-concurrent forces the magnitude and direction of the resultant come from ΣFx and ΣFy exactly as before, but its position must also be found: choose a point O and place R so that its moment about O equals ΣM_O. For parallel forces this gives the familiar x̄ = ΣFᵢxᵢ/ΣFᵢ. If ΣF = 0 but ΣM ≠ 0, the system reduces to a couple.
- M = F × perpendicular distance
- In coordinates: M_O = xFy − yFx
- Varignon: moment of R = Σ moments of components
- Couple: same moment Fd about every point
- Position of R: R·d = ΣM_O; parallel forces x̄ = ΣFx/ΣF
Example: Downward forces of 10 kN, 20 kN and 30 kN act at 0, 2 m and 5 m along a beam. Locate their resultant.
- R = 10 + 20 + 30 = 60 kN downward.
- Moments about the 0 m point: 20 × 2 + 30 × 5 = 40 + 150 = 190 kN·m.
- x̄ = 190/60 = 3.17 m.
Answer: 60 kN downward, 3.17 m from the first force
Example: A 100 N force at 30° above the x-axis acts at the point (2 m, 1 m). Find its moment about the origin.
- Fx = 100 cos 30° = 86.6 N, Fy = 100 sin 30° = 50 N.
- By Varignon, M = xFy − yFx = 2 × 50 − 1 × 86.6.
- M = 100 − 86.6 = 13.4 N·m; positive, so anticlockwise.
Answer: 13.4 N·m anticlockwise
Conditions of equilibrium in the plane and in space
A rigid body is in equilibrium when the resultant force and the resultant moment are both zero. In a plane that gives three independent equations, ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point, so at most three unknown reactions can be found by statics alone. Taking moments about a point where two unknowns meet removes them from the equation and is usually the quickest first step.
For three concurrent forces in equilibrium the force triangle closes, and Lami’s theorem follows from the sine rule: each force is proportional to the sine of the angle between the other two, P/sin α = Q/sin β = R/sin γ. A useful corollary: if a body is in equilibrium under exactly three non-parallel forces, those forces must meet at one point.
In space a force is written by components along x, y and z; a force F directed from the origin towards the point (a, b, c) has components F(a, b, c)/√(a² + b² + c²). Equilibrium of a concurrent system in space needs ΣFx = ΣFy = ΣFz = 0 (three equations); a general body in space needs these and ΣMx = ΣMy = ΣMz = 0, six equations in all.
- Plane: ΣFx = 0, ΣFy = 0, ΣM = 0 (three unknowns at most)
- Lami: P/sin α = Q/sin β = R/sin γ
- Three-force body: the forces are concurrent
- Space: unit vector (a, b, c)/√(a² + b² + c²)
- Space equilibrium: six equations, three for concurrent forces
Example: A 200 N lamp hangs from two cords making 30° and 45° with a horizontal ceiling. Find the tensions.
- The angle between the two cords is 180° − 30° − 45° = 105°.
- Angle between the 45° cord and the weight = 90° + 45° = 135°; between the 30° cord and the weight = 90° + 30° = 120°.
- Lami: T₁ (30° cord) = 200 sin 135°/sin 105° = 141.4/0.966 = 146.4 N.
- T₂ (45° cord) = 200 sin 120°/sin 105° = 173.2/0.966 = 179.3 N.
Answer: T₁ ≈ 146.4 N, T₂ ≈ 179.3 N
Example: A 6 m simply supported beam AB carries 20 kN at 2 m and 10 kN at 4.5 m from A. Find the reactions.
- ΣM_A = 0: R_B × 6 = 20 × 2 + 10 × 4.5 = 85 ⇒ R_B = 14.17 kN.
- ΣFy = 0: R_A = 30 − 14.17 = 15.83 kN.
- Check with ΣM_B: R_A × 6 = 20 × 4 + 10 × 1.5 = 95 ⇒ R_A = 15.83 kN.
Answer: R_A ≈ 15.83 kN, R_B ≈ 14.17 kN
Example: A 650 N force acts from the origin towards the point (3, 4, 12) m. Find its components.
- Length = √(9 + 16 + 144) = 13 m.
- Fx = 650 × 3/13 = 150 N, Fy = 650 × 4/13 = 200 N, Fz = 650 × 12/13 = 600 N.
Answer: (150, 200, 600) N
Coulomb friction: inclined plane, ladder and wedge
Dry (Coulomb) friction acts along the contact surface and opposes the motion that would otherwise happen. It adjusts itself up to a limit: F ≤ μN, with F = μN only when slipping is about to start (limiting equilibrium). The resultant of N and the limiting friction is inclined to the normal at the angle of friction φ, where tan φ = μ; a block on a plane begins to slide on its own when the slope reaches this angle, so the angle of repose equals φ.
On an incline of angle θ, for a force parallel to the plane, the force to just push a weight W up is W(sin θ + μ cos θ) and the force to just hold it from sliding down is W(sin θ − μ cos θ). For a uniform ladder of length l on a rough floor (μ) against a smooth wall, moments about the foot give the least angle with the floor at which it can stand: tan θ = 1/(2μ).
A wedge is a small tapered block used to lift or shift heavy loads with a modest push. Treat the load and the wedge as separate bodies, each with reactions tilted by φ from the normals in the direction that opposes their relative sliding. For a load W guided vertically and lifted by a wedge of angle α, with the same φ on both faces and a frictionless guide, the push is P = W[tan(α + φ) + tan φ].
- F ≤ μN; F = μN at impending motion
- tan φ = μ; angle of repose = φ
- Up the plane: W(sin θ + μ cos θ); hold: W(sin θ − μ cos θ)
- Ladder (smooth wall): tan θ_min = 1/(2μ)
- Wedge: tilt each reaction by φ against relative slip
Example: A 500 N block rests on a 30° incline with μ = 0.25. Find the force parallel to the plane to (a) just move it up, (b) just stop it sliding down.
- N = 500 cos 30° = 433.0 N, so limiting F = 0.25 × 433.0 = 108.3 N.
- Weight down the slope = 500 sin 30° = 250 N.
- (a) P = 250 + 108.3 = 358.3 N.
- (b) P = 250 − 108.3 = 141.7 N.
Answer: (a) 358.3 N, (b) 141.7 N
Example: A uniform 5 m ladder weighing 200 N leans on a smooth wall; the floor has μ = 0.4. Find the least angle with the floor at which it stays put.
- ΣFy: N = 200 N; ΣFx: R (wall) = F = μN = 80 N at slipping.
- Moments about the foot: R × 5 sin θ = 200 × 2.5 cos θ.
- tan θ = 500/(5 × 80) = 1.25, which is 1/(2μ).
- θ = tan⁻¹ 1.25 = 51.3°.
Answer: θ ≈ 51.3° with the floor
Example: A 2 kN load in a smooth vertical guide is raised by a 15° wedge; μ = 0.2 on both wedge faces. Find the horizontal push.
- φ = tan⁻¹ 0.2 = 11.31°.
- Load: the wedge reaction is tilted α + φ = 26.31° from vertical, so its horizontal part is W tan 26.31° = 2000 × 0.4944 = 989 N.
- Floor reaction on the wedge has vertical part W and horizontal part W tan φ = 400 N.
- P = 989 + 400 = 1389 N.
Answer: P ≈ 1.39 kN
Virtual work
A virtual displacement is an imagined, infinitesimally small displacement consistent with the constraints, made without the forces changing. The principle of virtual work states that a body (or a system of connected bodies with frictionless joints) is in equilibrium if and only if the total virtual work of the active forces is zero for every such displacement: δU = ΣF·δr = 0.
Its strength is that ideal reactions at pins, smooth surfaces and inextensible links do no work, so they drop out. A mechanism with one degree of freedom then gives one equation that relates the applied forces directly. Write the position of each loaded point in terms of a single coordinate (an angle θ, say), differentiate to get δx or δy in terms of δθ, add the works, and set the sum to zero.
For a reaction of a statically determinate beam, release the support, give it a virtual displacement δ, and treat the reaction as an applied force; the beam rotates as a rigid bar and the loads move in proportion to their distances. Work done by a force is positive when the displacement has the same sense as the force, and a weight does work −W δy when its point rises by δy.
- Virtual displacement: small, imagined, allowed by the constraints
- Equilibrium ⇔ δU = ΣF·δr = 0
- Ideal reactions do no work
- One coordinate: write positions, then differentiate
- Reactions: release the support and rotate the beam
Example: Two equal links AC and CB (length l) are pinned at C. A is a fixed pin, B a roller on the same level, and a 100 N load hangs at C. Find the horizontal force P at B that holds the toggle at θ = 30°.
- y_C = l sin θ ⇒ δy_C = l cos θ δθ; x_B = 2l cos θ ⇒ δx_B = −2l sin θ δθ.
- P pushes towards A, so its work is P × 2l sin θ δθ when θ grows; the load does −W l cos θ δθ.
- δU = 0 ⇒ P = W/(2 tan θ).
- P = 100/(2 × 0.5774) = 86.6 N.
Answer: P ≈ 86.6 N
Example: Use virtual work to find the right-hand reaction of a 6 m simply supported beam with 30 kN at 2 m from the left end.
- Release the right support and raise it by δ; the beam pivots about the left support.
- The load point rises by δ × 2/6 = δ/3.
- δU = R_B δ − 30 × δ/3 = 0.
- R_B = 10 kN.
Answer: R_B = 10 kN
A free-body diagram isolates a body and shows all external forces, including support reactions (roller: one force normal to the surface; hinge/pin: two components; fixed support: two forces and a moment). For equilibrium in a plane ΣFx = 0, ΣFy = 0 and ΣM = 0; for three concurrent forces Lami’s theorem applies. Dry friction resists impending motion with F ≤ μN; at limiting equilibrium F = μN and the angle of friction φ satisfies tan φ = μ. The principle of virtual work states that for a body in equilibrium the total work done by the forces in any virtual displacement compatible with the constraints is zero — convenient for mechanisms.
- Resultant of concurrent forces: R = √((ΣFx)² + (ΣFy)²), tan θ = ΣFy/ΣFx.
- Varignon: moment of the resultant = sum of moments of components.
- Lami: P/sin α = Q/sin β = R/sin γ (angles opposite each force).
- Angle of repose = angle of friction for a body on an incline.
- Block on incline: force to push up P = W(sin θ + μ cos θ) (parallel to plane).
- Ladder problems: friction at floor and wall; take moments about the foot.
Key formulas
- ΣFx = 0, ΣFy = 0, ΣM = 0
- F_lim = μN, tan φ = μ
- P/sin α = Q/sin β = R/sin γ
- δW = ΣF·δr = 0
Practice questions
A roller support provides
- one reaction normal to the surface
- two reactions
- two reactions and a moment
- no reaction
Show the answer
Answer: A. one reaction normal to the surface Free to roll.
If μ = 0.5, the angle of friction is about
- 26.6°
- 30°
- 45°
- 60°
Show the answer
Answer: A. 26.6° tan⁻¹(0.5).
Lami’s theorem applies to
- two forces
- three concurrent forces in equilibrium
- any number of forces
- parallel forces
Show the answer
Answer: B. three concurrent forces in equilibrium Sine rule form.
The number of equilibrium equations for a planar rigid body is
- 1
- 2
- 3
- 6
Show the answer
Answer: C. 3 ΣFx, ΣFy, ΣM.
Theory questions
State Lami’s theorem. (2 marks)
Show the model answer
If three concurrent coplanar forces keep a body in equilibrium, each force is proportional to the sine of the angle between the other two.
A body of weight 500 N rests on a plane inclined at 30°; μ = 0.25. Find the force parallel to the plane needed to (a) just move it up, (b) just prevent it sliding down. (6 marks)
Show the model answer
N = 500 cos 30° = 433 N, F = 108.3 N. W sin 30° = 250 N. (a) P = 250 + 108.3 = 358.3 N. (b) P = 250 − 108.3 = 141.7 N.
A uniform ladder of length L and weight W rests against a smooth wall at 60° with a rough floor. Find the minimum coefficient of friction at the floor to prevent slipping. State and apply the principle of virtual work to a simple lever. (10 marks)
Show the model answer
Floor N₁ = W, friction F; wall reaction R horizontal. Moments about foot: R·L sin 60° = W(L/2) cos 60° ⇒ R = W/(2 tan 60°) = 0.289W. F = R ⇒ μ_min = 0.289. Virtual work: for a lever with effort P at arm a and load W at arm b, a small rotation δθ gives Pa δθ − Wb δθ = 0 ⇒ P = Wb/a.
Analysis of Structures
Topics: Method of joints, method of sections, graphical method.
Trusses: assumptions and determinacy
A truss is a framework of straight bars joined at their ends to form triangles, used for roofs, bridges and towers. The analysis rests on idealisations: members are pinned at the ends, loads and reactions act only at the joints, and self-weight is ignored or shared to the joints. Each member is then a two-force member, carrying only an axial force: tension if it is pulled, compression if it is pushed.
A triangle is the simplest rigid shape, and adding two new members for each new joint keeps the frame rigid. A plane truss with j joints therefore needs m = 2j − 3 members to be just rigid and statically determinate (a perfect truss). With fewer it is deficient and collapses into a mechanism; with more it is redundant, and the extra forces need deformation, not statics alone.
Two observations save time. At a joint with only two non-collinear members and no load, both members carry zero force. At a joint with three members, two collinear and no load, the third member carries zero force and the collinear pair carry equal forces. Zero-force members are not useless; they brace against buckling and carry loads in other load cases.
- Pinned two-force members; loads at joints only
- Perfect truss: m = 2j − 3
- Deficient (m < 2j − 3) or redundant (m > 2j − 3)
- Unloaded two-member joint: both zero
- Unloaded T-joint: the odd member is zero
Example: A plane truss has 6 joints and 9 members. Is it perfect?
- 2j − 3 = 2 × 6 − 3 = 9.
- m = 9 equals this, so it is just rigid and statically determinate.
Answer: Yes, it is a perfect truss
Example: A triangular roof truss has rafters at 30° to the horizontal tie and a 10 kN load at the apex. Find the member forces.
- Each support reaction = 5 kN by symmetry.
- At a support joint, vertical balance: F_rafter sin 30° = 5 ⇒ F_rafter = 10 kN, pushing the joint (compression).
- Horizontal balance: F_tie = F_rafter cos 30° = 8.66 kN, pulling (tension).
Answer: Rafters 10 kN compression; tie 8.66 kN tension
Method of joints
In the method of joints each pin is a particle in equilibrium under concurrent forces, so two equations, ΣFx = 0 and ΣFy = 0, apply at each joint. Find the support reactions first from the whole truss, then start at a joint with no more than two unknown members, solve, and move on to the next joint where only two unknowns remain.
Assume every unknown member is in tension, so its force arrow points away from the joint. A positive answer confirms tension; a negative one means compression. Keep the sign when the same member force is used at its other end. Resolve each member force using the member’s own slope, cos and sin taken from its horizontal and vertical lengths.
The method gives every member force, which suits a full design check. Its drawback is that errors carry forward joint by joint. A final joint gives spare equations, and if they balance the whole solution is confirmed.
- Reactions first from the whole truss
- Start where only two members are unknown
- Assume tension; negative means compression
- Use each member’s slope for its components
- The last joint is a free check
Example: Truss ABC: A pinned, B on rollers 4 m away, apex C 3 m above the midpoint of AB, 12 kN down at C. Find the forces in AC and AB.
- By symmetry R_A = R_B = 6 kN.
- AC rises 3 m over 2 m: length √13, so sin = 3/√13 = 0.832 and cos = 2/√13 = 0.555.
- Joint A, vertical: F_AC × 0.832 + 6 = 0 ⇒ F_AC = −7.21 kN (compression).
- Joint A, horizontal: F_AB + F_AC × 0.555 = 0 ⇒ F_AB = +4.00 kN (tension).
Answer: AC 7.21 kN compression; AB 4.00 kN tension
Example: In a truss, joint D has only members DE and DF (not in a line) and carries no load. What are their forces?
- Resolve perpendicular to DE: only DF has a component, so F_DF = 0.
- Then the only force left at D is F_DE, which must also be zero.
Answer: Both are zero-force members
Method of sections
When only a few member forces are needed, cut the truss by an imaginary section through at most three members whose forces are unknown, and treat either piece as a rigid body with three equations. The cut members act on the piece as external forces, assumed in tension. The piece with fewer loads is usually the easier one.
The key trick is the choice of moment centre. Taking moments about the point where two of the cut members meet removes them both and gives the third directly. If two cut members are parallel, ΣF perpendicular to them gives the third. Each force is then found from one equation, so a mistake in one does not spoil the others.
For a Pratt-type truss with horizontal chords this gives tidy results: the bottom chord force is the bending moment at the opposite top joint divided by the depth, the top chord force is the bending moment at the opposite bottom joint divided by the depth, and the diagonal carries the shear force in the panel.
- Cut at most three unknown members
- Moments about the meeting point of two cut members
- Parallel chords: resolve perpendicular for the third
- Chord force = moment/depth; diagonal carries the shear
- Each force from its own equation
Example: A truss of span 12 m has four 3 m panels and depth 4 m, with 10 kN at each of the three inner bottom joints. Diagonals run from top joint U1 (3 m, 4 m) down to bottom joint L2 (6 m, 0). Cut panel 2 and find the bottom chord L1L2.
- Reactions: 30/2 = 15 kN at each end.
- Top chord U1U2 and diagonal U1L2 meet at U1, so take moments about U1 for the left piece.
- Left loads: 15 kN at x = 0 (lever 3 m) and 10 kN at L1 directly below U1 (lever 0).
- F × 4 = 15 × 3 = 45 ⇒ F = 11.25 kN, pulling: tension.
Answer: L1L2 = 11.25 kN tension
Example: For the same cut, find the top chord U1U2 and the diagonal U1L2.
- Moments about L2 (6 m, 0): 15 × 6 − 10 × 3 = 60 kN·m, so F_top × 4 = 60 ⇒ 15 kN, pushing: compression.
- Shear in the panel = 15 − 10 = 5 kN upward on the left piece.
- The diagonal slopes 3 across, 4 down (length 5), so its vertical share is 0.8 F.
- 0.8 F = 5 ⇒ F = 6.25 kN; it pulls down on the left piece: tension.
Answer: Top chord 15 kN compression; diagonal 6.25 kN tension
Graphical method (Maxwell diagram)
For a joint in equilibrium the force vectors, drawn head to tail, close into a polygon. The graphical method builds one combined force diagram for the whole truss (a Maxwell or Cremona diagram), so every member appears once as a line whose length, to scale, is its force. It is quick for roof trusses with many inclined members, and gives a visual check of a numerical solution.
Bow’s notation labels the spaces between external forces and members with letters, so a member between spaces a and b is drawn as line ab in the force diagram. First draw the load line: the external loads and reactions to scale, in order clockwise round the truss. Then, joint by joint, draw lines parallel to the members from the known points until they intersect.
The direction in which a member’s line is traced, read round a joint clockwise, tells whether it pushes the joint (compression) or pulls it (tension). Accuracy depends on scale and drawing care, usually within a few per cent, which is why the method is now used more as a check than a design tool.
- Force polygon of a joint must close
- Bow’s notation: letters for spaces; member ab
- Draw the load line to scale first
- Lines parallel to members locate new points
- Sense round the joint: towards = compression, away = tension
Example: Check joint A of the 4 m × 3 m truss above graphically: 6 kN up at A, members AC (slope 3/2) and AB (horizontal).
- Draw 6 kN upward to scale, say 1 cm per kN.
- From its head draw a line parallel to AC; from its tail a horizontal line for AB.
- They meet to close the triangle; measure AC ≈ 7.2 cm and AB ≈ 4.0 cm.
Answer: About 7.2 kN and 4.0 kN, as by joints
Example: At a joint, a 10 kN load and two members at right angles balance; one member is at 40° to the load line. Find the member forces graphically, then confirm.
- The force triangle is right-angled with the 10 kN load as hypotenuse.
- The members are 10 cos 40° and 10 sin 40°.
- So 7.66 kN and 6.43 kN.
Answer: 7.66 kN and 6.43 kN
A truss is a structure of straight two-force members pin-jointed at their ends and loaded only at joints, so each member is in pure tension or compression. A plane truss is simple (statically determinate) when m = 2j − 3. In the method of joints, equilibrium of each joint (ΣFx = ΣFy = 0) gives member forces, starting where at most two forces are unknown. The method of sections cuts through at most three members and uses three equilibrium equations, ideal for finding a few member forces. The graphical method draws force polygons (Maxwell diagram) with Bow’s notation.
- Perfect truss: m = 2j − 3; deficient if fewer members, redundant if more.
- Assume all members in tension; a negative answer means compression.
- Zero-force members: at an unloaded joint with two non-collinear members, both are zero.
- Method of sections: take moments about the intersection of two cut members to find the third directly.
- Support reactions first from the whole truss.
Key formulas
- m = 2j − 3
- At each joint: ΣFx = 0, ΣFy = 0
Practice questions
A perfect plane truss with 7 joints has
- 10 members
- 11 members
- 12 members
- 14 members
Show the answer
Answer: B. 11 members 2 × 7 − 3 = 11.
Truss members carry
- bending moments
- only axial forces
- torsion
- shear only
Show the answer
Answer: B. only axial forces Two-force members.
The method of sections can cut at most
- 2 unknown members
- 3 unknown members
- 4 unknown members
- any number
Show the answer
Answer: B. 3 unknown members Three equations available.
A negative member force (assuming tension) indicates
- tension
- compression
- zero force
- an error
Show the answer
Answer: B. compression Opposite sense.
Theory questions
What is a perfect truss? (2 marks)
Show the model answer
A truss with just enough members to be stable and statically determinate: m = 2j − 3.
State the assumptions made in the analysis of trusses. (4 marks)
Show the model answer
Members are straight and pin-connected at ends; loads and reactions only at joints; self weight neglected or lumped at joints; members are two-force members (axial only); truss is plane and statically determinate.
Explain the method of joints and the method of sections with a worked example of a simple triangular truss. (10 marks)
Show the model answer
Equilateral truss, span 4 m, load 10 kN at apex: reactions 5 kN each. Joint A: AC·sin 60° = 5 ⇒ AC = 5.77 kN (compression), AB = AC cos 60° = 2.89 kN (tension). By symmetry BC = 5.77 kN compression. Sections: cut AC and AB, take moments etc. Compare methods.
Centre of Gravity and Moment of Inertia
Topics: Centre of gravity and centroid; location for simple and composite bodies; moment of inertia of plane areas; parallel and perpendicular axis theorems; mass and polar moment of inertia; radius of gyration; product of inertia; principal axes and principal moments.
Centre of gravity and centroid
The centre of gravity of a body is the point through which its whole weight acts, whatever its orientation. For a uniform thin plate it coincides with the centroid of the area, the purely geometric centre given by x̄ = ∫x dA/A and ȳ = ∫y dA/A. A line of symmetry always contains the centroid, so a shape with two such lines has its centroid where they cross.
Standard results: rectangle at its centre; triangle at h/3 from the base (where the medians meet); semicircle at 4r/(3π) from the diameter; quarter circle at 4r/(3π) from each straight edge; and a right circular cone (solid) at h/4 from the base. Solids such as a hemisphere have their centre at 3r/8 from the flat face.
A composite area is split into simple parts with known centroids: x̄ = ΣAᵢxᵢ/ΣAᵢ and ȳ = ΣAᵢyᵢ/ΣAᵢ. A hole or cut-out enters with a negative area. Measuring every coordinate from one reference corner or edge, and tabulating A, x, Ax, y, Ay, keeps the arithmetic clean.
- x̄ = ΣAx/ΣA, ȳ = ΣAy/ΣA
- Symmetry axes contain the centroid
- Triangle h/3; semicircle 4r/(3π); solid cone h/4; hemisphere 3r/8
- Holes: negative area
- One reference for all coordinates
Example: A T-section has a 100 × 20 mm flange on top of a 20 × 80 mm web. Find the centroid from the bottom.
- Web: A = 1600 mm² at y = 40 mm. Flange: A = 2000 mm² at y = 80 + 10 = 90 mm.
- ΣAy = 1600 × 40 + 2000 × 90 = 64 000 + 180 000 = 244 000 mm³.
- ȳ = 244 000/3600 = 67.8 mm (on the axis of symmetry).
Answer: ȳ ≈ 67.8 mm from the bottom
Example: An unequal angle has a vertical leg 10 × 100 mm and a horizontal leg 70 × 10 mm attached at its foot (total width 80 mm). Find the centroid from the outer corner.
- Vertical leg: A = 1000, x = 5, y = 50. Horizontal leg: A = 700, x = 10 + 35 = 45, y = 5.
- x̄ = (1000 × 5 + 700 × 45)/1700 = 36 500/1700 = 21.5 mm.
- ȳ = (1000 × 50 + 700 × 5)/1700 = 53 500/1700 = 31.5 mm.
Answer: (21.5, 31.5) mm
Example: A 200 mm square plate has a 100 mm diameter hole centred at (150, 150) mm from one corner. Find the centroid.
- Square: 40 000 mm² at (100, 100). Hole: π × 50² = 7854 mm² at (150, 150), taken negative.
- x̄ = (40 000 × 100 − 7854 × 150)/(40 000 − 7854) = 2 821 900/32 146.
- x̄ = 87.8 mm, and ȳ is the same by symmetry about the diagonal.
Answer: (87.8, 87.8) mm
Area moment of inertia: parallel and perpendicular axes
The second moment of area I = ∫y² dA measures how far an area is spread from an axis. It governs the bending stiffness and strength of beams, which is why I-sections put most of their material in flanges far from the neutral axis. For a rectangle b wide and d deep, I about the centroidal axis parallel to b is bd³/12; about its base it is bd³/3. For a circle of diameter d, I_G = πd⁴/64.
The parallel-axis theorem shifts I from a centroidal axis to any parallel axis a distance h away: I = I_G + Ah². It works only from the centroidal axis, which is where I is least. For a composite section, find the centroid first, then add each part’s own I_G plus its Ah² about the common centroidal axis.
The perpendicular-axis theorem applies to plane areas: the polar moment about an axis normal to the plane equals the sum of the moments about two perpendicular axes in the plane through the same point, J = I_x + I_y. For a solid circle J = πd⁴/32, and for a hollow shaft J = π(D⁴ − d⁴)/32, used in torsion.
- Rectangle: bd³/12 (centroid), bd³/3 (base)
- Triangle: bh³/36 (centroid), bh³/12 (base)
- Circle: πd⁴/64; polar πd⁴/32
- Parallel axis: I = I_G + Ah²
- Perpendicular axis: J = I_x + I_y
Example: Find I about the horizontal centroidal axis of the T-section above (centroid 67.8 mm from the bottom).
- Flange: 100 × 20³/12 = 66 667, plus 2000 × (90 − 67.78)² = 987 654.
- Web: 20 × 80³/12 = 853 333, plus 1600 × (67.78 − 40)² = 1 234 568.
- Sum = 66 667 + 987 654 + 853 333 + 1 234 568 = 3 142 222 mm⁴.
Answer: I ≈ 3.14 × 10⁶ mm⁴
Example: Find the polar moment of a hollow shaft with D = 60 mm and d = 40 mm.
- D⁴ − d⁴ = 12 960 000 − 2 560 000 = 10 400 000 mm⁴.
- J = π × 10 400 000/32 = 1 021 018 mm⁴.
Answer: J ≈ 1.02 × 10⁶ mm⁴
Example: A rectangle is 60 mm wide and 120 mm deep. Find I_x, I_y and the polar moment about its centroid.
- I_x = 60 × 120³/12 = 8 640 000 mm⁴.
- I_y = 120 × 60³/12 = 2 160 000 mm⁴.
- J = I_x + I_y = 10 800 000 mm⁴.
Answer: I_x = 8.64, I_y = 2.16, J = 10.8 (× 10⁶ mm⁴)
Mass moment of inertia and radius of gyration
In rotation, mass moment of inertia I = ∫r² dm plays the role mass plays in translation: torque = Iα and kinetic energy = ½Iω². It depends on how far the mass lies from the axis, so the same mass gives more inertia in a ring than in a solid disc. Standard values: thin rod about its centre ML²/12 and about an end ML²/3; solid disc or cylinder MR²/2; thin ring MR²; solid sphere 2MR²/5.
The radius of gyration k is the distance at which the whole mass (or area) could be concentrated to give the same moment of inertia: I = Mk², or I = Ak² for areas. It condenses shape into one length and appears in column buckling and in rolling problems: a body rolling down a slope has acceleration g sin θ/(1 + k²/r²).
The parallel-axis theorem holds for mass moments as well, I = I_G + Md², and the perpendicular-axis theorem holds for thin flat plates. The flywheel of an engine is designed with most of its mass in the rim to get a large I, smoothing the speed between power strokes.
- Rod: ML²/12 centre, ML²/3 end
- Disc MR²/2; ring MR²; sphere 2MR²/5
- Radius of gyration: I = Mk² (or Ak²)
- Parallel axis: I = I_G + Md²
- Rolling: a = g sin θ/(1 + k²/r²)
Example: A solid disc flywheel has mass 50 kg and radius 0.4 m. Find I and k.
- I = ½ × 50 × 0.4² = 4 kg·m².
- k = √(I/M) = √(4/50) = 0.283 m (that is, R/√2).
Answer: I = 4 kg·m², k ≈ 0.283 m
Example: A 3 kg rod is 1.2 m long. Find I about one end.
- About the centre: 3 × 1.2²/12 = 0.36 kg·m².
- Shift 0.6 m to the end: 0.36 + 3 × 0.6² = 0.36 + 1.08 = 1.44 kg·m² (= ML²/3).
Answer: 1.44 kg·m²
Example: Find the radius of gyration of the 60 × 120 mm rectangle about its horizontal centroidal axis.
- I_x = 8 640 000 mm⁴ and A = 7200 mm².
- k = √(8 640 000/7200) = √1200 = 34.6 mm (that is, d/√12).
Answer: k ≈ 34.6 mm
Product of inertia and principal axes
The product of inertia I_xy = ∫xy dA can be positive, negative or zero. It is zero whenever either axis is an axis of symmetry, because the contributions on the two sides cancel. It has its own transfer rule: I_xy = I_x′y′ + A x̄ ȳ, where x̄ and ȳ locate the centroid from the new axes.
Rotating the axes changes I_x, I_y and I_xy, but at one orientation the product of inertia vanishes. Those are the principal axes, at angle θ given by tan 2θ = 2I_xy/(I_y − I_x), and the moments about them are the greatest and least possible: I_max, min = (I_x + I_y)/2 ± √[((I_x − I_y)/2)² + I_xy²]. Their sum always equals I_x + I_y.
Unsymmetrical sections such as an unequal angle bend about their principal axes, not about the axes parallel to their legs, so a vertical load can make them deflect sideways too. Mohr’s circle, centred at (I_x + I_y)/2 with radius √[((I_x − I_y)/2)² + I_xy²], gives the same results graphically.
- I_xy = ∫xy dA; zero if either axis is a symmetry axis
- Transfer: I_xy = I_x′y′ + A x̄ ȳ
- tan 2θ = 2I_xy/(I_y − I_x)
- I_max, min = (I_x + I_y)/2 ± √[((I_x − I_y)/2)² + I_xy²]
- I_max + I_min = I_x + I_y
Example: Find I_xy of a 40 mm × 60 mm rectangle about axes along two of its edges meeting at a corner.
- About its own centroidal axes I_xy = 0 by symmetry.
- Transfer: I_xy = 0 + A x̄ ȳ = 2400 × 20 × 30.
- I_xy = 1 440 000 mm⁴ (which equals b²h²/4).
Answer: 1.44 × 10⁶ mm⁴
Example: A section has I_x = 4, I_y = 1 and I_xy = 1.5 (× 10⁶ mm⁴). Find the principal moments and the axis angle.
- Average = 2.5; radius = √(1.5² + 1.5²) = 2.121.
- I_max = 4.621, I_min = 0.379 (× 10⁶ mm⁴).
- tan 2θ = 3/(1 − 4) = −1 ⇒ 2θ = −45°, θ = −22.5° (the other axis at 67.5°).
Answer: 4.62 and 0.38 × 10⁶ mm⁴; axes at −22.5° and 67.5°
The centroid of an area is its geometric centre, x̄ = ΣAᵢxᵢ/ΣAᵢ, ȳ = ΣAᵢyᵢ/ΣAᵢ; for composite areas add parts and subtract holes. The (second) moment of area I = ∫y²dA measures resistance to bending about an axis; the parallel-axis theorem I = I_G + Ah² transfers it from the centroidal axis, and the perpendicular-axis theorem I_z = I_x + I_y gives the polar moment for plane areas. Radius of gyration k = √(I/A). Principal axes are those where the product of inertia I_xy is zero; I is then maximum and minimum.
- Rectangle (b × d): I_G = bd³/12, about the base bd³/3.
- Circle: I_G = πd⁴/64; polar J = πd⁴/32.
- Triangle (b, h): I_G = bh³/36, about the base bh³/12; centroid h/3 from the base.
- Semicircle centroid 4r/(3π) from the diameter.
- Mass MOI: rod about centre ML²/12, solid disc MR²/2, solid sphere 2MR²/5.
- Principal axes: tan 2θ = 2I_xy/(I_y − I_x).
Key formulas
- x̄ = ΣAᵢxᵢ/ΣAᵢ
- I = I_G + Ah²
- I_z = I_x + I_y
- k = √(I/A)
Practice questions
The centroid of a triangle from its base is at
- h/2
- h/3
- 2h/3
- h/4
Show the answer
Answer: B. h/3 One third of the height.
I of a rectangle about its centroidal axis parallel to b is
- bd³/3
- bd³/12
- db³/12
- bd²/6
Show the answer
Answer: B. bd³/12 Standard result.
The parallel-axis theorem is
- I = I_G − Ah²
- I = I_G + Ah²
- I = I_x + I_y
- I = Ak²
Show the answer
Answer: B. I = I_G + Ah² Transfer formula.
The polar moment of inertia of a circle of diameter d is
- πd⁴/64
- πd⁴/32
- πd³/32
- πd²/4
Show the answer
Answer: B. πd⁴/32 J = I_x + I_y.
Theory questions
State the parallel and perpendicular axis theorems. (3 marks)
Show the model answer
Parallel: I about any axis = I about a parallel centroidal axis + Ah². Perpendicular (plane areas): I about an axis normal to the plane = sum of I about two perpendicular in-plane axes through the same point.
Find the centroid of a T-section: flange 100 × 20 mm, web 20 × 80 mm (web below flange). (5 marks)
Show the model answer
Flange A₁ = 2000 mm², y₁ = 90 mm; web A₂ = 1600 mm², y₂ = 40 mm (from the bottom). ȳ = (2000 × 90 + 1600 × 40)/3600 = 67.8 mm from the bottom.
Find the moment of inertia of the above T-section about its centroidal horizontal axis and its radius of gyration. (10 marks)
Show the model answer
Flange: I = 100 × 20³/12 + 2000 × (90 − 67.8)² = 66 667 + 985 680 ≈ 1.052×10⁶. Web: 20 × 80³/12 + 1600 × (67.8 − 40)² = 853 333 + 1 236 544 ≈ 2.090×10⁶. Total ≈ 3.14×10⁶ mm⁴; k = √(3.14×10⁶/3600) ≈ 29.5 mm.
Kinetics of Particles and Rigid Bodies
Topics: Newton’s second law, D’Alembert’s principle, linear and angular impulse and momentum, impulse–momentum principle, work–energy principle.
Newton’s second law and D’Alembert’s principle
Newton’s second law, ΣF = ma, links the forces on a particle to its acceleration. Draw the free-body diagram as in statics, choose a positive direction (usually the direction of motion), and write the law along each axis. Connected bodies, such as blocks joined by a string over a pulley, each get their own equation, tied together by a common acceleration and string tension.
D’Alembert’s principle rewrites the law as ΣF + (−ma) = 0: add an imaginary inertia force −ma, opposite to the acceleration, and the body may be treated as if in equilibrium. This lets the familiar statics tools, including moments, solve dynamic problems. It is especially handy for lifts, vehicles braking or accelerating, and bodies on rotating platforms.
In a lift accelerating upward the floor must push harder than the weight, N = m(g + a); accelerating downward, N = m(g − a); in free fall N = 0. For two masses over a light frictionless pulley (an Atwood machine), a = (m₁ − m₂)g/(m₁ + m₂) and T = 2m₁m₂g/(m₁ + m₂).
- ΣF = ma along each axis
- D’Alembert: add −ma and use equilibrium
- Lift: N = m(g ± a)
- Atwood: a = (m₁ − m₂)g/(m₁ + m₂)
- Tension T = 2m₁m₂g/(m₁ + m₂)
Example: A 70 kg person stands in a lift accelerating upward at 2 m/s². Find the floor reaction.
- Inertia force 70 × 2 = 140 N acts downward (opposite to a).
- Equilibrium: N = 70 × 9.81 + 140 = 686.7 + 140.
Answer: N ≈ 826.7 N
Example: Masses of 5 kg and 3 kg hang over a light frictionless pulley. Find the acceleration and tension.
- a = (5 − 3) × 9.81/8 = 2.45 m/s².
- T = 2 × 5 × 3 × 9.81/8 = 36.8 N.
- Check on 5 kg: 5 × 9.81 − 36.8 = 12.26 ≈ 5 × 2.45.
Answer: a ≈ 2.45 m/s², T ≈ 36.8 N
Example: A 20 kg block on a floor with μ = 0.3 is pulled by a 100 N horizontal force. Find its acceleration.
- N = 20 × 9.81 = 196.2 N; friction = 0.3 × 196.2 = 58.9 N.
- a = (100 − 58.9)/20 = 2.06 m/s².
Answer: a ≈ 2.06 m/s²
Rigid bodies in plane motion
A rigid body in plane motion translates with its centre of mass and rotates about it. Its equations are ΣF = ma_G for the centre and ΣM_G = I_Gα for the rotation. For rotation about a fixed axis O the moment equation may be written about O instead: ΣM_O = I_Oα, with I_O from the parallel-axis theorem.
Rolling without slipping links the two motions: a_G = rα and v_G = rω. Friction at the contact supplies the torque that spins the body, but does no work because the contact point is momentarily at rest. For a body rolling down a slope, combining the equations gives a = g sin θ/(1 + k²/r²): a sphere (k²/r² = 2/5) beats a disc (1/2), which beats a ring (1).
D’Alembert’s principle extends to rigid bodies by adding an inertia force −ma_G at the centre and an inertia couple −I_Gα; then the body is in dynamic equilibrium and moments can be taken about any convenient point.
- ΣF = ma_G; ΣM_G = I_Gα
- Fixed axis: ΣM_O = I_Oα
- Rolling: a = rα, v = rω
- Slope: a = g sin θ/(1 + k²/r²)
- Inertia couple −I_Gα with D’Alembert
Example: A rope wound on a 10 kg solid disc (radius 0.3 m) on a fixed frictionless axle is pulled with 30 N. Find α.
- I = ½ × 10 × 0.3² = 0.45 kg·m².
- Torque = 30 × 0.3 = 9 N·m.
- α = 9/0.45 = 20 rad/s².
Answer: α = 20 rad/s²
Example: A solid sphere rolls without slipping down a 30° slope. Find its acceleration.
- k²/r² = 2/5 for a solid sphere.
- a = 9.81 × 0.5/(1 + 0.4) = 4.905/1.4.
Answer: a ≈ 3.50 m/s²
Work–energy principle and power
Work done by a constant force is W = F s cos θ, the force times the displacement along it. The work–energy principle states that the total work done by all forces on a body equals the change in its kinetic energy: ΣU₁→₂ = ½mv₂² − ½mv₁². It skips acceleration and time entirely, so it is the natural tool when speeds and positions are given.
Gravity does work −mg Δh and a spring does work −½k(x₂² − x₁²); these can be moved to the other side as changes in potential energy, which gives conservation of mechanical energy when no friction acts. Friction always removes energy, F × distance, as heat. For rotating bodies the kinetic energy includes ½I_Gω², and a rolling body has both parts.
Power is the rate of doing work, P = Fv for a force moving at speed v, or Tω for a torque. Efficiency is the output power divided by the input power. A vehicle at steady speed must supply power equal to the resisting force times the speed.
- W = Fs cos θ
- ΣU = ΔKE = ½m(v₂² − v₁²)
- Gravity −mgΔh; spring −½k(x₂² − x₁²)
- Rolling KE = ½mv² + ½Iω²
- P = Fv = Tω; efficiency = output/input
Example: A 2 kg body falls 5 m onto a spring of stiffness 4000 N/m. Find the maximum compression x.
- From rest to rest: mg(5 + x) = ½ × 4000 x².
- 2000x² − 19.62x − 98.1 = 0.
- x = [19.62 + √(19.62² + 8000 × 98.1)]/4000 = (19.62 + 886.1)/4000.
- x = 0.226 m.
Answer: x ≈ 0.226 m
Example: A block slides 10 m down a 30° slope from rest; μ = 0.2. Find its speed at the bottom.
- Work per unit mass: g × 10 (sin 30° − 0.2 cos 30°) = 98.1 × 0.3268 = 32.06 J/kg.
- ½v² = 32.06 ⇒ v² = 64.1.
- v = 8.01 m/s; the mass cancels.
Answer: v ≈ 8.0 m/s
Example: A car meets 600 N of resistance at a steady 20 m/s. What power must its engine deliver to the wheels?
- At steady speed the driving force equals the resistance, 600 N.
- P = Fv = 600 × 20 = 12 000 W.
Answer: 12 kW
Impulse and momentum; collisions
Integrating Newton’s law over time gives the impulse–momentum principle: ∫F dt = mv₂ − mv₁. The impulse of a force is the area under its force–time graph, so a short sharp blow is described by its impulse even when the force itself is unknown. The average force is the impulse divided by the contact time; padding works by stretching the time and so lowering the force.
For rotation the same idea reads ∫M dt = I(ω₂ − ω₁): an angular impulse changes angular momentum. When the net external impulse (or angular impulse) on a system is zero, its momentum (or angular momentum) is conserved; this holds during a collision, because the large internal forces cancel in pairs.
In a direct central collision momentum is conserved, and Newton’s experimental law fixes how the bodies separate: v₂ − v₁ = e(u₁ − u₂), with the coefficient of restitution e between 0 (perfectly plastic, bodies move together) and 1 (perfectly elastic, no loss of kinetic energy). Kinetic energy is lost whenever e < 1.
- ∫F dt = Δ(mv); average F = impulse/time
- ∫M dt = Δ(Iω)
- No external impulse ⇒ momentum conserved
- v₂ − v₁ = e(u₁ − u₂)
- e = 1 elastic; e = 0 plastic
Example: A 0.15 kg ball arrives at 30 m/s and leaves the bat at 40 m/s in the opposite direction; contact lasts 0.01 s. Find the impulse and average force.
- Δv = 40 − (−30) = 70 m/s.
- Impulse = 0.15 × 70 = 10.5 N·s.
- Average force = 10.5/0.01 = 1050 N.
Answer: 10.5 N·s; 1.05 kN
Example: A 2 kg ball at 6 m/s strikes a 3 kg ball at rest head-on; e = 0.5. Find the velocities after impact.
- Momentum: 2v₁ + 3v₂ = 12.
- Restitution: v₂ − v₁ = 0.5 × 6 = 3.
- Substitute v₂ = v₁ + 3: 5v₁ + 9 = 12 ⇒ v₁ = 0.6 m/s, v₂ = 3.6 m/s.
Answer: 0.6 m/s and 3.6 m/s, both forward
Example: A constant torque of 20 N·m acts for 3 s on a flywheel with I = 4 kg·m², from rest. Find its final speed.
- Angular impulse = 20 × 3 = 60 N·m·s.
- ω = 60/4 = 15 rad/s.
Answer: 15 rad/s
Newton’s second law F = ma governs particles; for rigid bodies in plane motion ΣF = ma_G and ΣM_G = I_Gα. D’Alembert’s principle adds an inertia force −ma so a dynamics problem becomes one of (dynamic) equilibrium. The work–energy principle states that the work done by all forces equals the change in kinetic energy, avoiding acceleration altogether. The impulse–momentum principle states that impulse ∫F dt equals the change of momentum; with no external impulse momentum is conserved (collisions, coefficient of restitution e).
- D’Alembert: F − ma = 0 (inertia force opposite acceleration).
- Work–energy: ΣW = ½mv₂² − ½mv₁²; rolling adds ½Iω².
- Power = F·v; efficiency = output/input.
- Impulse J = ∫F dt = Δ(mv); angular impulse ∫M dt = Δ(Iω).
- Collisions: e = (v₂ − v₁)/(u₁ − u₂); e = 1 elastic, e = 0 perfectly plastic.
- Lift problems: N = m(g ± a).
Key formulas
- ΣF = ma, ΣM_G = I_Gα
- W = ΔKE
- J = Δp
- e = separation speed/approach speed
Practice questions
D’Alembert’s principle converts a dynamics problem into
- a static equilibrium problem
- an energy problem
- a momentum problem
- a kinematics problem
Show the answer
Answer: A. a static equilibrium problem Add inertia forces.
Work done by all forces equals change in
- momentum
- kinetic energy
- potential energy only
- velocity
Show the answer
Answer: B. kinetic energy Work–energy theorem.
For a perfectly elastic collision e =
- 0
- 0.5
- 1
- ∞
Show the answer
Answer: C. 1 Kinetic energy conserved.
A man of 60 kg in a lift accelerating up at 2 m/s² presses the floor with (g = 9.8)
- 588 N
- 708 N
- 468 N
- 600 N
Show the answer
Answer: B. 708 N 60 × 11.8.
Theory questions
State D’Alembert’s principle. (2 marks)
Show the model answer
The external forces on a body and the reversed effective (inertia) force −ma together form a system in equilibrium.
A 2 kg body falls 5 m onto a spring of stiffness 4 kN/m. Find the maximum compression (g = 9.81). (6 marks)
Show the model answer
Work–energy: mg(h + x) = ½kx² ⇒ 2 × 9.81(5 + x) = 2000x² ⇒ 2000x² − 19.62x − 98.1 = 0 ⇒ x ≈ 0.226 m.
Explain the work–energy and impulse–momentum principles with examples, and solve: a 10 g bullet at 400 m/s embeds in a 2 kg block at rest; find their common velocity and the energy lost. (10 marks)
Show the model answer
Principles as above. Momentum: 0.01 × 400 = 2.01v ⇒ v = 1.99 m/s. KE before = 800 J; after = ½ × 2.01 × 1.99² ≈ 3.98 J; loss ≈ 796 J (as heat and deformation).
Harmonic Motion
Topics: Harmonic oscillator; damped harmonic motion: over-damped, critically damped and under-damped; forced oscillation and resonance.
The simple harmonic oscillator
A mass m on a spring of stiffness k, displaced by x from equilibrium, feels a restoring force −kx. Newton’s law gives mẍ + kx = 0, whose solution is x = A sin(ωₙt + ϕ) with natural frequency ωₙ = √(k/m). The motion repeats every T = 2π/ωₙ, and the frequency f = 1/T is fixed by the system, not by how far it is pulled.
Velocity and acceleration follow by differentiation: the maximum speed is Aωₙ (at the centre) and the maximum acceleration Aωₙ² (at the ends). Energy swaps between kinetic and spring forms with the total ½kA² constant. For a vertical spring, gravity only shifts the equilibrium by the static deflection δ = mg/k, which gives the handy formula ωₙ = √(g/δ).
Springs in series combine like resistors in parallel, 1/k = 1/k₁ + 1/k₂, while springs in parallel add, k = k₁ + k₂. A simple pendulum is also harmonic for small swings, with ωₙ = √(g/l).
- mẍ + kx = 0
- ωₙ = √(k/m); T = 2π/ωₙ; f = 1/T
- v_max = Aωₙ; a_max = Aωₙ²
- Static deflection: ωₙ = √(g/δ)
- Series 1/k = Σ1/kᵢ; parallel k = Σkᵢ
Example: A 2 kg mass hangs on a 200 N/m spring. Find ωₙ, T and f.
- ωₙ = √(200/2) = 10 rad/s.
- T = 2π/10 = 0.628 s.
- f = 1/0.628 = 1.59 Hz.
Answer: 10 rad/s, 0.628 s, 1.59 Hz
Example: A machine deflects its mounting springs statically by 5 mm. Find its natural frequency.
- ωₙ = √(g/δ) = √(9.81/0.005) = √1962 = 44.3 rad/s.
- f = 44.3/(2π) = 7.05 Hz.
Answer: f ≈ 7.05 Hz
Example: An oscillator with ωₙ = 10 rad/s has amplitude 50 mm. Find its maximum speed and acceleration.
- v_max = 0.05 × 10 = 0.5 m/s.
- a_max = 0.05 × 10² = 5 m/s².
Answer: 0.5 m/s and 5 m/s²
Free damped vibration
Real vibrations die away because energy is lost. Viscous damping, a force proportional to speed (−cẋ), gives mẍ + cẋ + kx = 0. Its character depends on the damping ratio ζ = c/c_c, where the critical damping c_c = 2√(km) = 2mωₙ. With ζ < 1 (under-damped) the system oscillates inside a shrinking exponential envelope at the damped frequency ω_d = ωₙ√(1 − ζ²).
With ζ = 1 (critically damped) the mass returns to rest in the shortest time without overshooting; with ζ > 1 (over-damped) it creeps back more slowly without oscillating. Car suspensions are made somewhat under-damped (ζ about 0.2 to 0.4) for comfort, while door closers and measuring instruments are set close to critical so they settle quickly without bouncing.
Damping is measured from a decay record using the logarithmic decrement δ = ln(x₁/x₂), the natural log of the ratio of two successive peaks. Over n cycles δ = (1/n) ln(x₀/xₙ). It relates to the damping ratio by δ = 2πζ/√(1 − ζ²), or ζ = δ/√(4π² + δ²).
- mẍ + cẋ + kx = 0
- c_c = 2√(km) = 2mωₙ; ζ = c/c_c
- Under-damped ω_d = ωₙ√(1 − ζ²)
- ζ = 1 fastest return; ζ > 1 slow creep
- δ = ln(x₁/x₂) = 2πζ/√(1 − ζ²)
Example: A system has m = 5 kg, k = 2000 N/m and c = 40 N·s/m. Find ωₙ, ζ, ω_d and δ.
- ωₙ = √(2000/5) = 20 rad/s.
- c_c = 2 × 5 × 20 = 200 N·s/m ⇒ ζ = 40/200 = 0.2.
- ω_d = 20√(1 − 0.04) = 19.6 rad/s.
- δ = 2π × 0.2/√0.96 = 1.28.
Answer: 20 rad/s, 0.2, 19.6 rad/s, 1.28
Example: Find the critical damping coefficient for m = 10 kg and k = 4000 N/m.
- c_c = 2√(km) = 2√40 000.
- c_c = 2 × 200 = 400 N·s/m.
Answer: 400 N·s/m
Example: Peaks of a free vibration fall from 10 mm to 2 mm over 5 cycles. Find δ and ζ.
- δ = (1/5) ln(10/2) = 0.322.
- ζ = 0.322/√(4π² + 0.322²) = 0.322/6.291.
- ζ = 0.051.
Answer: δ ≈ 0.322, ζ ≈ 0.051
Forced vibration and resonance
When a harmonic force F₀ sin ωt drives the damped system, the motion settles (after the free part decays) into a steady vibration at the driving frequency ω, lagging the force by a phase angle ϕ. Its amplitude X compared with the static deflection X_st = F₀/k is the magnification factor X/X_st = 1/√[(1 − r²)² + (2ζr)²], where r = ω/ωₙ is the frequency ratio, and tan ϕ = 2ζr/(1 − r²).
At low r the response follows the force almost statically; at high r inertia dominates and the amplitude falls below the static value. Near r = 1 the response peaks: this is resonance, and the peak (about 1/(2ζ) for light damping) is limited only by damping. Resonance is why soldiers break step on bridges and why machines are run well away from the natural frequencies of their mountings.
Designers avoid resonance by changing stiffness or mass to move ωₙ, by adding damping to cap the peak, or by running far above ωₙ, which also isolates the base: transmitted force is reduced only when r > √2. The phase angle passes through 90° at resonance.
- X/X_st = 1/√[(1 − r²)² + (2ζr)²]
- r = ω/ωₙ; X_st = F₀/k
- tan ϕ = 2ζr/(1 − r²); 90° at r = 1
- Peak ≈ 1/(2ζ) near r = 1
- Isolation needs r > √2
Example: m = 10 kg, k = 4000 N/m, c = 80 N·s/m, driven by 100 N at 16 rad/s. Find the steady amplitude and phase.
- ωₙ = 20 rad/s, r = 0.8; c_c = 400 ⇒ ζ = 0.2; X_st = 100/4000 = 25 mm.
- X/X_st = 1/√[(0.36)² + (0.32)²] = 1/√0.232 = 2.08.
- X = 25 × 2.08 = 51.9 mm.
- tan ϕ = 0.32/0.36 ⇒ ϕ = 41.6°.
Answer: X ≈ 51.9 mm, lagging by 41.6°
Example: For the same system driven at 20 rad/s, find the amplitude.
- r = 1, so X/X_st = 1/(2ζ) = 2.5.
- X = 25 × 2.5 = 62.5 mm.
Answer: 62.5 mm (resonance)
A mass on a spring obeys mẍ + kx = 0 and oscillates with natural frequency ωₙ = √(k/m). Adding viscous damping c gives mẍ + cẋ + kx = 0, characterised by the damping ratio ζ = c/(2√(km)): ζ < 1 under-damped (decaying oscillation), ζ = 1 critically damped (fastest return without overshoot), ζ > 1 over-damped (slow return). Under a harmonic force F₀ sin ωt the steady response has amplitude X = (F₀/k)/√[(1 − r²)² + (2ζr)²] with r = ω/ωₙ; near r = 1 the amplitude peaks — resonance.
- T = 2π√(m/k); f = 1/T.
- Damped natural frequency ω_d = ωₙ√(1 − ζ²).
- Logarithmic decrement δ = ln(x₁/x₂) = 2πζ/√(1 − ζ²).
- Critical damping c_c = 2√(km) = 2mωₙ.
- Resonance: maximum amplitude near ω = ωₙ, limited only by damping.
- Applications: vehicle suspensions (≈ critical), door closers, vibration isolators, instruments.
Key formulas
- ωₙ = √(k/m)
- ζ = c/(2√(km))
- ω_d = ωₙ√(1 − ζ²)
- X/X_st = 1/√[(1 − r²)² + (2ζr)²]
Practice questions
Critical damping gives
- oscillation
- fastest non-oscillatory return
- no return
- resonance
Show the answer
Answer: B. fastest non-oscillatory return ζ = 1.
Natural frequency of a 2 kg mass on a 200 N/m spring is
- 10 rad/s
- 100 rad/s
- 1 rad/s
- 20 rad/s
Show the answer
Answer: A. 10 rad/s √(200/2).
At resonance the forcing frequency equals
- zero
- the natural frequency
- twice the natural frequency
- the damping ratio
Show the answer
Answer: B. the natural frequency r = 1.
An over-damped system has ζ
- < 1
- = 1
- > 1
- = 0
Show the answer
Answer: C. > 1 Heavy damping.
Theory questions
Define damping ratio. (2 marks)
Show the model answer
ζ = actual damping coefficient/critical damping coefficient = c/(2√(km)).
A spring–mass system has m = 5 kg, k = 2000 N/m and c = 40 N·s/m. Find ωₙ, ζ, ω_d and the logarithmic decrement. (6 marks)
Show the model answer
ωₙ = √400 = 20 rad/s; c_c = 2 × 5 × 20 = 200 ⇒ ζ = 0.2; ω_d = 20√0.96 = 19.6 rad/s; δ = 2π(0.2)/√0.96 = 1.28.
Derive the equation of motion of a damped spring–mass system, discuss the three cases of damping with sketches, and explain resonance in forced vibration. (10 marks)
Show the model answer
mẍ + cẋ + kx = 0; trial x = e^(st) ⇒ s = −ζωₙ ± ωₙ√(ζ² − 1). ζ > 1: two real negative roots, x = Ae^(s₁t) + Be^(s₂t), no oscillation. ζ = 1: repeated root, x = (A + Bt)e^(−ωₙt), fastest return. ζ < 1: complex roots, x = Xe^(−ζωₙt) sin(ω_dt + φ), decaying oscillation. Forced: steady amplitude formula; peak near r = 1, large when ζ small; phase 90° at r = 1; examples: bridges, machines, tuning.